A novel potato peels waste ß-cyclodextrin biocomposite for the efficient uptake of diuron and glyphosate herbicides.

A novel biocomposite (FPPW-ß-CD) was prepared by a simple and sustainable method involving fine potato peel waste, ß-cyclodextrin (ß-CD), and green citric acid through the crosslinking reaction. The polymer was characterized using SEM, FTIR, XRD, TGA, and DSC analyses. The adsorbent performance was evaluated about the glyphosate and diuron adsorption from the aqueous solution. Pesticide removal was investigated regarding the influence of solution pH, temperature, and initial concentration of contaminants. Also, it highlights the main interactions involved in the adsorption phenomenon based on the pH effect and characteristics of adsorbent and adsorbate molecules. The maximum adsorption capacity values according to the Sips model were higher than 2000 µg g-1. The pseudo-second-order and general-order models described the kinetic data well. Thermodynamic parameters indicated that pesticide removal was spontaneous and favorable. The magnitude of enthalpy variation values (27.37 kJ mol-1 and - 100.79 kJ mol-1) revealed that the glyphosate and diuron adsorption occurred through the physisorption and chemisorption, respectively. The novel biocomposite is a promising green adsorbent for the uptake of micropollutant pesticides in aqueous solutions at concentrations of µg L-1.

A statistical physics-based physicochemical study of L-phenylalanine adsorption on activated carbon.

CONTEXT: In this comparative study of the adsorption of L-phenylalanine (L-Phe) on two modified low-activated carbons (ACK and ACZ) at four temperatures (293-313 K), steric and energetic characteristics of adsorption were investigated. An advanced statistical physics multilayer model involving single-layer and double-layer adsorption scenarios was developed to interpret the L-Phe adsorption phenomenon. Modeling results indicate that two and three L-Phe layers were arranged depending on the tested adsorption systems. The estimated number of L-Phe molecules per leading adsorption site varied from 1.71 to 2.09 and from 1.76 to 1.86 for systems L-Phe-ACK and L-Phe-ACZ, respectively. The results show that a multimolecular adsorption mechanism might connect this amino acid molecule on ACZ and ACK surfaces in a non-parallel location. These parameters changed as follows, according to the adsorbed quantity at saturation analysis: Qasat (L-Phe-ACK) ˃ Qasat (L-Phe-ACZ). This indicates that ACK material was more efficient and valuable for L-Phe adsorption than ACZ. It was also shown that the adsorption capacity decreases as the temperature increases, proving the exothermicity of the adsorption process. This analytical substantiation is confirmed by calculating the binding energies, suggesting the occurrence of physical bonds between L-Phe amino acid molecules and ACK/ACZ binding sites and among L-Phe-L-Phe molecules. Pore size distribution was interpreted and calculated by applying the Kelvin theory to data from single adsorption isotherms. All used temperatures depicted a distribution of pores below 2 nm. The docking analysis involving L-Phe and the ACZ and ACK adsorbents reveal a significant resemblance in how receptors detect ligands. Consequently, the findings from the docking process confirm that the calculated binding affinities fall within the spectrum of adsorption energy. METHODS: This study analyzed the adsorption capacity of the L-Phe through a model proposed by statistical physics formalism. Molecular docking was used to determine the various types of interactions between the two activated carbons. Two aspects, including orientation of L-Phe on the site, number of molecules per site n, interaction energy, density of receptor site, and adsorption capacity, were discussed to elucidate the influence of activation on the two adsorbents.

Efficient removal of organophosphate insecticide employing magnetic chitosan-derivatives.

Herein, this work reports an efficient acephate adsorption using chitosan (CS) incorporating varying amounts of magnetite. A co-precipitation methodology was employed for the functionalization of chitosan with iron nanoparticles, using Fe2+ as the sole iron source and with a low energy requirement. The adsorbents were characterized by FTIR, XRD, VSM, and nitrogen porosimetry techniques. The CS∙Fe3O4 1:1 NPs showed the highest acephate removal percentage (74.96 %) at pH 9 and ambient temperatures. The adsorption process exhibited high dependencies on pH, adsorbent dosage, initial concentration of adsorbate, and ionic strength. Sips and pseudo-second-order kinetics models best adjusted the experimental data, suggesting that the process occurs on a heterogeneous surface. Thermodynamic evaluation showed that the adsorption was exothermic, favorable, and predominately through chemical interactions. Finally, the CS∙Fe3O4 showed no significant decrease after several cycles of adsorption/desorption, avoiding centrifugation-filtration steps.

Effect of combining aminomethacrylate and fluoride against erosive and abrasive challenges on enamel and dentin.

This study evaluated the effect of solutions containing aminomethacrylate copolymer (AA) and sodium fluoride (F; 225 ppm F-) or fluoride plus stannous chloride (FSn; 225 ppm F-, 800 ppm Sn2+) against enamel and dentin erosion/abrasion. Solutions F, FSn, AA, F+AA, FSn+AA, and deionized water as negative control were tested. Bovine enamel and dentin specimens (n = 13/solution/substrate) underwent a set of erosion-abrasion cycles (0.3% citric acid [5 min, 4×/day], human saliva [1 h, 4×/day], brushing [15 s, 2×/day], and treatments [2 min, 2×/day]) for each of five days. Initial enamel erosion was evaluated using Knoop microhardness after the first and second acid challenge on day 1, and surface loss with profilometry after day 5. KOH-soluble fluoride was assessed. Data were analyzed with ANOVA/Tukey tests. The combination of fluoride and AA resulted in higher protection against enamel erosion, whereas this was not the case for the combination of AA and FSn. All treatments protected against enamel and dentin loss. The lowest surface loss values were observed with F+AA and FSn+AA. The polymer did not significantly influence the KOH-soluble fluoride formation on enamel/dentin specimens. The aminomethacrylate copolymer effectively enhanced the efficacy of sodium fluoride against initial erosion and improved the control of enamel and dentin wear of F and FSn solutions.

Rethinking food loss and waste to promote sustainable resource use and climate change mitigation in agri-food systems: A review.

The sustainable agri-food system is an important sector recognized for promoting the United Nations' Sustainable Development Goals on food security, resource conservation and climate change mitigation. However, the increasing food loss and waste (FLW) along the supply chains has continued to hinder these goals. This study evaluates the trend of FLW research from 1975 to 2022 and how it promotes the achievement of resource and environmental sustainability in agri-food systems. The salient research themes and hotspots that are of interest to researchers were identified. Bibliometric and network analyses were carried out on scholarly research articles from the Scopus database using bibliometrix and VOSviewer. Furthermore, the content analysis was conducted on the selected highly influential articles containing relevant data to understand the role of FLW in promoting sustainable agri-food systems. The results showed disaggregate and unbalanced research distribution on the impacts of FLW among the countries, with China and the United States having the highest contributions. The identified major research themes relating to sustainable agri-food systems are food waste and sustainable systems, food waste management and food waste impact assessment. Moreover, the circular economy was found to be a relatively new approach being explored in agri-food systems to promote FLW reduction and ensure sustainability of resource use. This study highlights the critical role of the impact of FLW in addressing the grand challenge of food security, resource use efficiency and environmental sustainability.

Statistical physical modeling insights for urinary analgesic drug adsorption on carbon nanomaterial derivative.

The presence of phenazopyridine in water is an environmental problem that can cause damage to human health and the environment. However, few studies have reported the adsorption of this emerging contaminant from aqueous matrices. Furthermore, existing research explored only conventional modeling to describe the adsorption phenomenon without understanding the behavior at the molecular level. Herein, the statistical physical modeling of phenazopyridine adsorption into graphene oxide is reported. Steric, energetic, and thermodynamic interpretations were used to describe the phenomenon that controls drug adsorption. The equilibrium data were fitted by mono, double, and multi-layer models, considering factors such as the numbers of phenazopyridine molecules by adsorption sites, density of receptor sites, and half saturation concentration. Furthermore, the statistical physical approach also calculated the thermodynamic parameters (free enthalpy, internal energy, Gibbs free energy, and entropy). The maximum adsorption capacity at the equilibrium was reached at 298 K (510.94 mg g-1). The results showed the physical meaning of adsorption, indicating that the adsorption occurs in multiple layers. The temperature affected the density of receptor sites and half saturation concentration. At the same time, the adsorbed species assumes different positions on the adsorbent surface as a function of the increase in the temperature. Meanwhile, the thermodynamic functions revealed increased entropy with the temperature and the equilibrium concentration.

Removal of phenazopyridine from water, synthetic urine, and real sample by adsorption using graphene oxide: A DFT theoretical/experimental approach.

Herein, graphene oxide was used as the highly efficient phenazopyridine adsorbent from aqueous medium, synthetic, and human urine. The nanoadsorbent was characterized by different instrumental techniques. The adsorption capacity (1253.17 mg g-1) was reached at pH 5.0, using an adsorbent dosage of 0.125 g L-1 at 298 K. The Sips and Langmuir described the equilibrium data well. At the same time, the pseudo-second order was more suitable for fitting the kinetic data. Thermodynamic parameters revealed the exothermic nature of adsorption with an increase in randomness at the solid-liquid interface. The magnitude of the enthalpy variation value indicates that the process involves the physisorption phenomenon. At the same time, ab initio molecular dynamics data corroborated with the thermodynamic results, indicating that adsorbent and adsorbate establish hydrogen bonds through the amine groups (adsorbate) and hydroxyl groups on the adsorbent surface (weak interactions). Electrostatic interactions are also involved. Additionally, the adsorption assays conducted in simulated medium and human urine showed the excellent performance of adsorbent material to remove the drug in real concentrations excreted by the kidneys (removal values higher than 60%).

Adsorptive features of cyclohexane carboxylic naphthenic acid on a novel cross-linked polymer developed from spent coffee grounds.

Naphthenic acids (NA) are organic compounds commonly found in crude oil and produced water, known for their recalcitrance and toxicity. This study introduces a new adsorbent, a polymer derived from spent coffee grounds (SCGs), through a straightforward cross-linking method for removing cyclohexane carboxylic acid as representative NA. The adsorption kinetics followed a pseudo-second-order model for the data (0.007 g min-1 mg-1), while the equilibrium data fitted the Sips model ( q m = 140.55 mg g-1). The process's thermodynamics indicated that the target NA's adsorption was spontaneous and exothermic. The localized sterical and energetic aspects were investigated through statistical physical modeling, which corroborated that the adsorption occurred indeed in monolayer, as suggested by the Sips model, but revealed the contribution of two energies per site ( n 1 ; n 2 ). The number of molecules adsorbed per site ( n ) was highly influenced by the temperature as n 1 decreased with increasing temperature and n 2 increased. These results were experimentally demonstrated within the pH range between 4 and 6, where both C6H11COO-(aq.) and C6H11COOH(aq.) species coexisted and were adsorbed by different energy sites. The polymer produced was naturally porous and amorphous, with a low surface area of 20 to 30 m2 g-1 that presented more energetically accessible sites than other adsorbents with much higher surface areas. Thus, this study shows that the relation between surface area and high adsorption efficiency depends on the compatibility between the energetic states of the receptor sites, the speciation of the adsorbate molecules, and the temperature range studied.

Advanced technologies in water treatment: Chitosan and its modifications as effective agents in the adsorption of contaminants.

Chitosan, derived from the abundant biopolymer chitin, has emerged as a promising option for water treatment due to its intrinsic bioavailability. This review emphasizes the notable characteristics of chitosan, which allow for various modifications, expanding its applications. The polymer's effectiveness in adsorbing contaminants, particularly in advanced water treatment technologies, is highlighted. The review underscores the potential of chitosan-based hybrid materials, including nanocomposites, hydrogels, membranes, films, sponges, nanoparticles, microspheres, and flakes, as innovative alternatives to traditional chemical-based adsorbents. The advantages of using these materials in wastewater treatment, especially in removing heavy metals, dyes, and emerging compounds, are explored. The study delves into the mechanisms involved in wastewater treatment with chitosan, emphasizing the interactions between the polymer and various contaminants. Additionally, the application of chitosan as a contaminant removal agent in a post-pandemic context is addressed, considering the challenges related to waste management and environmental preservation. The analysis highlights the potential contribution of chitosan in mitigating environmental impacts post-pandemic, offering practical solutions for treating contaminated effluents and promoting sustainability. The study addresses current obstacles and prospects for chitosan-based wastewater treatment, emphasizing its promising role in sustainable water management.

Remediation through the coordinated use of local rice husk residues for the selective adsorption of iron and nickel in real landfill leachate.

Herein, we demonstrate the prospects of tackling several environmental problems by transforming a local rice husk residue into an effective adsorbent, which was then applied for the treatment of real landfill leachate (LL). The study focused on establishing (i) the effect of simple washing on morphological aspects, (ii) evaluating target adsorption capacity for total iron (Fe) and nickel (Ni), (iii) determining regeneration and reuse potential of the adsorbent and (iv) complying to the requirements of worldwide legislations for reuse of treated LL wastewater. The adsorbent was prepared by employing a simple yet effective purification process that can be performed in situ. The LL was collected post-membrane treatment, and the characterizations revealed high concentrations of Fe, Ni, and organic matter content. The simple washing affected the crystallinity, resulting in structural alterations of the adsorbents, also increasing the porosity and specific surface. The adsorption process for Ni occurred naturally at pH 6, but adjusting the pH to 3 significantly improved removal efficiency and adsorption capacity for total Fe. The kinetics were accurately described by the pseudo-second-order model, while the Langmuir model provided a better fit for the isotherms. The adsorbent was stable for 5 reuses, and the metals adsorbed were recovered through basic leaching. The removal capacities achieved underscore the remarkable effectiveness of the process, ensuring the treated LL wastewater meets rigorous global environmental legislations for safe use in irrigation. Thus, by employing the compelling methods herein optimized it is possible to refer to the of solving three environmental problems at once.

Valorization of winemaking residues as biochar for removing Ni(II) from real industrial painting process effluent in a fixed-bed column.

In this work, the adsorption of nickel ions from a real effluent from a metal-mechanic industry was investigated in a fixed-bed column using biochar. Biochar was prepared from winemaking residues originating from the Beifiur® composting process. The use of wine industry residues as precursor materials for biochar production is established in biomass residue valorization using the existing logistics and the lowest possible number of manipulations and pre-treatments. The results found in the work showed that the optimal conditions for nickel adsorption in fixed-bed columns were bed height (Z) of 7 cm, initial nickel concentration (C0) of 1.5 mg L-1, and flow rate (Q) of 18 mL min-1. In this condition, the maximum adsorption capacity of the column was 0.452 mg g-1, the mass transfer zone (Zm) was 3.3 cm, the treated effluent volume (Veff) was 9.72 L, and the nickel removal (R) was 92.71%. The Yoon-Nelson and BDST dynamic models were suitable to represent the breakthrough curves of nickel adsorption. Finally, the fixed-bed column adsorption using biochar from winemaking residues proved to be a promising alternative for nickel removal from real industrial effluents.

Neodymium adsorption from aqueous solution by ß-cyclodextrin nanosponges and a polymer valorized from potato peels waste: experiments and conventional and statistical physics interpretations.

Using organic waste and residue streams to be turned into valuable and greener materials for various applications has proven an efficient and suitable strategy. In this work, two green materials (nanosponges and a polymer) were synthesized using potato peels and applied for the first time to adsorb and recover Neodymium (Nd3+) from aqueous solutions. The recovery of Nd3+ that belongs to the rare earth elements has attracted important interest due to its/their importance in several industrial and technological applications. The fine potato peel waste (FPPW) polymer presented an irregular shape and porous surface. At the same time, the ß-cyclodextrin (ß-CD) nanosponges had uniform distribution with regular and smooth shapes. ß-CD nanosponges exhibited a much higher total carboxyl content (4.02 mmol g-1) than FPPW (2.50 mmol g-1), which could impact the Nd3+ adsorption performance because carboxyl groups can interact with cations. The adsorption capacity increased with the increase of the pH, reaching its maximum at pHs 6-7 for ß-CD nanosponges and 4-7 for FPPW polymer. The kinetic and equilibrium data were well-fitted by General order and Liu models. ß-CD nanosponges attained adsorption capacity near 100 mg Nd per gram of adsorbent. Thermodynamic and statistical physical results corroborated that the adsorption mechanism was due to electrostatic interaction/complexation and that the carboxyl groups were important in the interactions. ß-CD nanosponges (three cycles of use) were more effective than FPPW (one cycle of use) in the regeneration. Finally, ß-CD nanosponges could be considered an eco-friendly adsorbent to recover Nd3+ from aqueous matrices.

Adsorption of rare earth elements on a magnetic geopolymer derived from rice husk: studies in batch, column, and application in real phosphogypsum leachate sample.

There is a growing need to develop new strategies for rare earth element (REE) recovery from secondary resources. Herein, a novel approach to utilize biogenic silica (from rice husk) and metakaolin was employed to fabricate magnetic geopolymer (MGP) by incorporating metallic iron. The fabricated MGP adsorbent material was used to uptake Ce3+, La3+, and Nd3+ from synthetic solutions and real phosphogypsum leachate in batch and column modes. The MGP offers a negatively charged surface at pH above 2.7, and the uptake of REEs rises from pH 3 to 6. The kinetic study validated that the kinetics was much faster for Nd3+, followed by La3+ and Ce3+. A thermodynamic investigation validated the exothermic nature of the adsorption process for all selected REEs. The desorption experiment using 2 mol L-1 H2SO4 as the eluent demonstrated approximately 100% desorption of REEs from the adsorbent. After six adsorption-desorption cycles, the MGP maintained a high adsorption performance up to cycle five before suffering a significant decrease in performance in cycle six. The effectiveness of MGP was also assessed for its applicability in recovering numerous REEs (La3+, Ce3+, Pr3+, Sm3+, and Nd3+) from real leachate from phosphogypsum wastes, and the highest recovery was achieved for Nd3+ (95.03%) followed by Ce3+ (86.33%). The operation was also feasible in the column presenting suitable values of the length of the mass transfer zone. The findings of this investigation indicate that MGP adsorbent prepared via a simple route has the potential for the recovery of REEs from synthetic and real samples in both batch and continuous operations modes.

Recovery of Ce and La from phosphogypsum leachate by adsorption using grape wastes.

The present research aimed to evaluate the use of grape stalk in the adsorption of lanthanum and cerium to identify the best operating conditions enabling the application of the bioadsorbent in REEs leached from phosphogypsum. The grape stalk was characterized and showed an amorphous structure with a heterogeneous and very porous surface. Also, it was possible to identify the groups corresponding to carboxylic acids, phenols, alcohols, aliphatic acids, and aromatic rings. The pH effect study showed that the adsorption process of La3+ and Ce3+ ions was favored at pH 5.0. The adsorption kinetics followed the pseudo-second-order model. In just 20 min, 80% saturation was reached, while equilibrium was reached after 120 min. The adsorption isotherms were appropriately adjusted to the Langmuir model, and the maximum adsorption capacities were obtained at 298 K, which were 35.22 mg g-1 for La3+ and 37.99 mg g-1 for Ce3+. Furthermore, the adsorption process was favorable, spontaneous, and exothermic. In the study's second phase, phosphogypsum was leached with a sulfuric acid solution. Then, the adsorption of REEs was carried out under the experimental conditions of pH after leaching and pH 5.0 (adjustment carried out with sodium hydroxide solution) at 298 K for 120 min and with adsorbent dosages of 1 and 5 g L-1. This process resulted in removal percentages above 95% for the most abundant REEs, such as neodymium, lanthanum, and cerium, at pH 5.0 and a dosage of 5 g L-1, demonstrating the effectiveness of the bioadsorbent used. These results indicate the potential of using grape residue as a promising bioadsorbent in recovering rare earth elements from phosphogypsum leachate.

Carbonaceous adsorbent as green silica by-product applied to the treatment of contaminated effluent by pesticide commonly sprayed on rice cultivation.

Grain cultivation and its impacts on the environment have been the focus of many studies, especially due to generated solid waste and the wide use of agrochemicals aiming for greater productivity. In this context, the present study proposes a new and consistent step in constructing self-sustainability in rice farming. The proposed stage includes reusing green silica waste as an adsorbent to treat effluents contaminated by pesticides directly applied to rice cultivation. After nano silica production through the rice husks burning, followed by basic leaching and acid precipitation, a carbonaceous material remains. This material, naturally impregnated by Na2SiO3, was washed and dried, characterized, and used to remove the pesticide 2,4-dichlorophenoxyacetic acid (2,4-D). The adsorption essays were performed at 2,4-D at low concentrations (between 1 and 10 mg L-1) at different temperatures. The washed and dried porous carbon (WDPC) surface is irregular and presents slit-shaped channels. The FT-IR analysis identified the siloxane, carbonyl, carboxylate, and methylene functional groups available to interact with the pesticide molecules. The washing/drying process eliminated impurities, improving the surface area from 539.67 to 619.67 cm2 g-1 and pore volume from 0.29 to 0.44 cm3 g-1. Concerning the adsorption of 2,4-D on WDPC, the best pH was 6.0, where around 75% of the pesticide was removed from the water. The equilibrium isotherms presented an S-shaped form indicating a multilayer and cooperative adsorption, with maximum adsorption capacities of 7.504 and 7.736 mg g-1. The estimated ∆Gads, ΔHads, and ΔSads values suggested that pesticide adsorption was spontaneous, exothermic, and favorable. Finally, WDPC demonstrated a good potential to uptake 2,4-D from water, contributing to self-sustainability in rice farming.

From grape bagasse to graphene-like porous carbon nanosheets for CO2 capture.

Graphene-based materials have increasingly attracted attention in recent years. It is a material is recognized worldwide due to its numerous applications in several sectors. However, graphene production involves several challenges: scalability, high costs, and high-quality production. This study synthesized graphene-like porous carbon nanosheets (GPCNs) through a thermochemical process under a nitrogen atmosphere using grape bagasse as a precursor. Three temperatures (700, 800, and 900 ºC) of the pyrolysis process were studied. Chemical graphitization and activation were used to form high-specific surface area materials: FeCl3.6H2O(aq) and ZnCl2(s) in a simultaneous activation-graphitization (SAG) method. The materials obtained (GPCN700, GPCN800, and GPCN900) were compared to previously produced chars (C700, C800, and C900). A high specific surface area and total pore volume were obtained for GPCN materials, and GPCN900 presented the highest values: 1062.7 m2g-1 and 0.635 cm3 g-1, respectively. The GPCN and char materials were classified as mesoporous and applied as adsorbents for CO2(g). The GPCN800 presented the best CO2(g) adsorbent, with a CO2(g) adsorption capacity of 168.71 mg g-1.

Valorization of a poultry industry floated sludge as a raw material to produce char and activated carbon for pharmaceutical compounds adsorption.

This study was intended to valorize a floated sludge of a poultry slaughterhouse using it as a precursor to producing char and activated carbon, which were tested as adsorbents in removing ketoprofen and diclofenac sodium from the water. The addition of zinc chloride or calcium hydroxide was determinant for forming a porous carbonaceous structure with a high surface area in AC-FSP (656.54 m2 g-1), differently from that exhibited by the CHAR-FSP (8.11 m2 g-1). Kinetic and equilibrium studies indicated that the pseudo-second-order and the Sips models were suitable. The AC- FSP maximum adsorption capacity for ketoprofen and diclofenac sodium was 124.98 mg g-1 and 138.32 mg g-1, respectively. The adsorption was a spontaneous and endothermic process. It was concluded that AC-FSP is a more efficient and promising adsorbent than CHAR-FSP for the adsorption of drugs in contaminated wastewater. In addition, AC-FSP can be reused, maintaining good adsorption levels for about 5 cycles. Therefore, this study is aligned with the 2030 Agenda for global sustainability since converting waste (valueless) into an adsorbent is also directly linked to the circular economy and neutral carbon.

Adsorption of chloroquine, propranolol, and metformin in aqueous solutions using magnetic graphene oxide nanocomposite.

The work proposes the application of a nanocomposite formed by graphene oxide and magnetite to remove chloroquine, propranolol, and metformin from water. Tests related to adsorption kinetics, equilibrium isotherms and adsorbent reuse were studied, and optimization parameters related to the initial pH of the solution and the adsorbent dosage were defined. For all pharmaceuticals, adsorption tests indicated that removal efficiency was independent of initial pH at adsorbent dosages of 0.4 g L-1 for chloroquine, 1.2 g L-1 for propranolol, and 1.6 g L-1 for metformin. Adsorption equilibrium was reached within the first few minutes, and the pseudo-second-order model represented the experimental data well. While the equilibrium data fit the Sips isotherm model at 298 K, the predicted maximum adsorption capacities for chloroquine, propranolol, and metformin were 44.01, 16.82, and 12.23 mg g-1, respectively. The magnetic nanocomposite can be reused for three consecutive cycles of adsorption-desorption for all pharmaceuticals, being a promising alternative for the removal of different classes of pharmaceuticals in water.

Application of Pb-Fe spinel-activated carbon for phenol removal from aqueous solutions: fixed-bed adsorption studies.

Fixed-bed studies for phenol uptake from water were carried out using a novel Pb-Fe spinel-activated carbon adsorbent. A characterization phase including TGA, FTIR, SEM, and BET analyses was performed for the developed active carbon. In column studies, the influence of initial phenol concentration, column bed height, and the solution flow rate was investigated at natural pH. Adsorption of phenol onto Pb-Fe spinel-activated carbon composite and pristine activated carbon was analyzed in the form of breakthrough curves. Under optimum conditions, the maximum adsorption capacities for the magnetic active carbon composite and pristine activated carbon were found to be 113.95 and 102.61 mg/g, respectively. Results indicated that the adsorption capacity of adsorbent for all examined conditions was higher than that obtained for unmodified activated carbon because the composite contains additional metal hydroxides compared with the pristine activated carbon. The Yoon and Nelson, Thomas, and instantaneous local equilibrium (ILE) models were used to explain column data collected under different operating conditions. Finally, the results of the continuous adsorption process were explained successfully using the Yoon-Nelson and Thomas models. Thus, the phenol adsorption on Pb-Fe@MAC was a feasible operation to be performed in fixed-bed mode.

Lead ferrite-activated carbon magnetic composite for efficient removal of phenol from aqueous solutions: synthesis, characterization, and adsorption studies.

A novel lead ferrite-magnetic activated carbon (lead ferrite-MAC) composite was developed using the chemical co-precipitation method. Instrumental analyses such as X-ray diffraction (XRD), scanning electron microscopy (SEM), Fourier-transform infrared spectroscopy (FTIR), and Brunauer-Emmett-Teller (BET) analysis were performed to characterize adsorbent. The uptake of phenol from aqueous solutions using the developed adsorbent was compared to that of pristine activated carbon. The maximum adsorption capacity of lead ferrite-MAC composite (145.708 mg/g) was more than that of pristine activated carbon (116.606 mg/g) due to the metal hydroxides coated on activated carbon since they improve the retention of phenol on the available active sites of adsorbent and create an additional electrostatic interaction with the phenol adsorbate. Regarding the high value of the coefficient of determination (R2) and adjusted determination coefficient (R2adj), coupled with the lower values of average relative error (ARE) and minimum squared error (MSE), it can be found that the isothermal data for the lead ferrite-MAC adsorbent were in agreement with the isotherm models of Redlich-Peterson and Langmuir. From the kinetic viewpoint, pseudo-second-order and linear driving force models explained the phenol adsorption data for both adsorbents. The reusability tests for lead ferrite-MAC composite revealed that after six cycles, 85% of the initial adsorption capacity was maintained. The developed adsorbent can be successfully applied to uptake phenol from aqueous solutions.