Development of a certified reference material for the determination of acrylamide in potato chips.

A certified reference material (CRM), KRISS CRM 108-10-003, has been developed for analysis of acrylamide in potato chips, as a representative of carbohydrate-rich food cooked in high-temperature oil. The material was prepared by grinding commercially available potato chips to a paste which was then homogenized, bottled in 15-g units, and stored at -70 °C. Certification, homogeneity and stability testing, were carried out by liquid chromatography-isotope-dilution mass spectrometry (ID-LC-MS). A single ID-LC-MS measurement was performed for each of 10 selected units for certification and homogeneity assessment. The mean measurement result for the 10 bottles, 0.455 ± 0.012 mg kg(-1), was assigned as the certified value of the CRM. The between-bottle homogeneity was 0.8% of the certified value. The within-bottle homogeneity, tested by measuring three replicate sub-samples from each of three randomly selected bottles, was similar to the between-bottle homogeneity. The stability of the CRM under storage conditions (-70 °C) was tested for 21 months and no change in the acrylamide content was observed within the measurement uncertainty. Stability of the CRM at -20 °C (storage at user's site) and room temperature (for regular use and transportation) was also tested. Also presented is the newly designed procedure for evaluating the uncertainty of the certified value for the characterization scheme used in this study.

Mass spectrometric studies of alkali metal ion binding on thrombin-binding aptamer DNA.

The binding sites and consecutive binding constants of alkali metal ions, (M(+) = Na(+), K(+), Rb(+), and Cs(+)), to thrombin-binding aptamer (TBA) DNA were studied by Fourier-transform ion cyclotron resonance spectrometry. TBA-metal complexes were produced by electrospray ionization (ESI) and the ions of interest were mass-selected for further characterization. The structural motif of TBA in an ESI solution was checked by circular dichroism. The metal-binding constants and sites were determined by the titration method and infrared multiphoton dissociation (IRMPD), respectively. The binding constant of potassium is 5-8 times greater than those of other alkali metal ions, and the potassium binding site is different from other metal binding sites. In the 1:1 TBA-metal complex, potassium is coordinated between the bottom G-quartet and two adjacent TT loops of TBA. In the 1:2 TBA-metal complex, the second potassium ion binds at the TGT loop of TBA, which is in line with the antiparallel G-quadruplex structure of TBA. On the other hand, other alkali metal ions bind at the lateral TGT loop in both 1:1 and 1:2 complexes, presumably due to the formation of ion-pair adducts. IRMPD studies of the binding sites in combination with measurements of the consecutive binding constants help elucidate the binding modes of alkali metal ions on DNA aptamer at the molecular level.

A sphingosine kinase activity assay using direct infusion electrospray ionization tandem mass spectrometry.

D-erythro-Sphingosine is known to be phosphorylated by sphingosine kinase to yield sphingosine-1-phosphate. With the importance of sphingosine-1-phosphate in biological functions being made evident by recent research, a selective and convenient method of assay to measure sphingosine kinase activity is required. Here we developed a new sphingosine kinase assay using murine teratocarcinoma mutant F9-12 cells and electrospray ionization tandem mass spectrometry (ESI-MS/MS) with direct infusion. Sphingosine-1-phosphate in the crude extract of enzyme reaction mixture was selectively characterized and quantitated using precursor ion scanning for [PO(3)](-) in the negative electrospray ionization mode. The method was successfully validated for an activator and an inhibitor of sphingosine kinase. Direct quantitation of S1P without the use of radioactive reagents, chemical derivatization, and extensive chromatographic separation enables simplified assay for sphingosine kinase activity at the cellular system level, and the use of a structural analog as an internal standard provides robustness to the assay.

Evaluation of the internal temperatures of an 8.6 kDa protein cation exposed to a hot dispenser cathode employed in electron capture dissociation mass spectrometry.

The 'effective' internal temperature of an 8.6 kDa ubiquitin cation was estimated under electron capture dissociation (ECD) conditions, in which a dispenser cathode electron source was mounted just outside an ion cyclotron resonance (ICR) cell, i.e., axially displaced at a distance less than 1 cm from the rear trap plate of the ICR cell. In this ECD configuration, thermal activation of the molecular ions stored in the ICR cell was anticipated since the heated dispenser cathode (T(cathode surface) > 1000 degrees C) emitted a large amount of (both visible and infrared) radiation as well as electrons. An evaluation of the internal temperature of ubiquitin 6+ and 7+ cations was made by comparing our ECD fragmentation patterns with those obtained by McLafferty et al. (J. Am. Chem. Soc. 2002; 124: 6407) as a function of the ion temperature. In McLafferty's configuration, the heating (or thermal activation) effect of their filament source was minimal since the filament was displaced by a distance as far as 70 cm from their ICR cell. A careful comparison reveals that the fragmentation patterns obtained in this work are very similar to those previously measured at T approximately 125 degrees C. In terms of sequence coverage, our ECD configuration provides better results, and in particular without the aid of any other simultaneous activation method, such as thermal heating, infrared multiphoton irradiation, or collisional activation, except for the visible and infrared radiation from the heated cathode.

Determination of serum cortisol using isotope dilution-liquid chromatography-mass spectrometry as a candidate reference method.

We propose isotope-dilution mass spectrometry as a candidate reference method for determination of serum cortisol. The method uses liquid chromatography-mass spectrometry (LC-MS), interfaced with electrospray ionization, and selective monitoring of the [M + H]+ ions of cortisol and isotopically labeled cortisol. The isotope-dilution-liquid chromatography-mass spectrometry (ID-LC-MS) method simplifies sample-preparation, because samples are processed by simple solvent extraction without further clean-up and derivatization. We studied the time required for complete equilibration of endogenous cortisol and labeled cortisol spiked into serum and found it to be less than 1 h. The repeatability and the reproducibility of the method were evaluated and found to be 0.55% of the measurement value. CRM 192 and 193 from the Bureau Communautaire de Reference were analyzed for verification of the method. The results obtained from the ID-LC-MS method agreed with the certified values. The relative uncertainty of measurement results for samples in the range of a few tens of micrograms per kilogram to several hundred micrograms per kilogram was evaluated and found to be 0.56%. Immunoassay carried out by three independent clinical laboratories produced results more than 15% higher than this ID-LC-MS method, suggesting the presence of bias in the immunoassay methods.