Rheological Properties of Industrial Hot Trub.

The boiling of beer wort with hops results in the formation of a hot trub, a sediment consisting mainly of water-insoluble tannin and protein conglomerates and hop residue. Hot trub is a waste product, removed in a clarifying tank and discarded. The use of barley malt substitutes in recipes for beer is associated with an increase in the amount of generated hot trub. In presented study, an analysis of the rheological properties of industrial hot trub was carried out. Samples varied with regard to the quantities of unmalted barley (0%, 35%, and 45%) and worts' extract (12.5, 14.1, 16.1, and 18.2 °Plato) in the recipe. The rheology of each type of sludge was determined using a hysteresis loop at four different temperatures. The results showed the shear-thinning and thixotropic properties of the hot trub. It was found that, regardless of the raw material and extract used, all samples exhibited the same rheological properties, but with different values. It was also proved that both raw material composition and temperature affected the hot trub's rheology. The highest values of viscosity were identified for malted barley, whereas the lowest apparent viscosity values were recorded for the hot trub with a 30% addition of unmalted barley. The Herschel-Bulkley model had the best fit to the experimental data.

Predictive Model for the Surface Tension Changes of Chemical Solutions Used in a Clean-in-Place System.

The paper presents the results concerning the influence of concentration and storage time on the equilibrium surface tension of chemical solutions used in a clean-in place (CIP) system. Standard cleaning solutions (prepared under laboratory conditions) and industrial solutions (used in a CIP system in a brewery) were subjected to tests. Solutions from the brewery were collected after being regenerated and changes in equilibrium surface tension were studied during a three-month storage. In the statistical analysis of the solutions, standard deviations were determined in relation to the averages, and a Tukey's multiple comparison test was performed to determine the effect of dependent variables on the surface tension of solutions. From the results, a nonlinear regression model was developed that provided a mathematical description of the kinetics of changes in the wetting properties of the solutions during their storage. A linear-logarithmic function was adopted to describe the regeneration. Numerical calculations were performed based on the nonlinear least squares method using the Gauss-Newton algorithm. The adequacy of the regression models with respect to the empirical data was verified by the coefficient of determination R and the standard error of estimation Se. The results showed that as the concentration of the substance in the cleaning solution increased, its wetting properties decreased. The same effect was observed with increased storage time as the greatest changes occurred during the first eight weeks. The study also showed that the use of substances to stabilize the cleaning solutions prevented deterioration of their wetting properties, regardless of the concentration of the active substance or storage time.

Rheological and Microbiological Characteristics of Hops and Hot Trub Particles Formed during Beer Production.

During the production of beer, and especially beer wort, the main wastes are spent grain and hot trub, i.e., the so-called "hot break." Combined with yeast after fermentation, they represent the most valuable wastes. Hot trub is also one of the most valuable by-products. Studies on the chemical composition of these sediments and their rheological properties as waste products will contribute to their effective disposal and even further use as valuable pharmaceutical and cosmetic raw materials. So far, hot trub has been studied for morphology and particle distribution depending on the raw material composition and beer wort extract. However, there are no preliminary studies on the rheological properties of hot trub and hops. In particular, no attention has yet been paid to the dependence of these properties on the hop variety or different protein sources used. The aim of this study was to examine the effect of different hopping methods on hot trub viscosity and beer wort physicochemical parameters. Additionally, the hop solutions were measured at different temperatures. A microbiological analysis of hop sediments was also performed to determine the post-process survival of selected microorganisms in these wastes. For manufacturers of pumps used in the brewing industry, the most convenient material is that of the lowest viscosity. Low viscosity hot trub can be removed at lower velocities, which reduces costs and simplifies washing and transport. The sediments also had similar equilibrium viscosity values at high shear rates.

Increasing the Efficiency of Food Material Cutting during Inclined and Shear Movements of Knife.

Mathematical models for predicting the resistance forces that are developed during the inclined and sliding cutting of food materials have been developed. The dependence of the actual cutting angle on the angle of inclination and sliding speed of the cutting edge at various sharpening angles have been investigated. For the inclined cutting mode, the dependence of the useful resistance force on the cutting speed has been determined at various angles of inclination of the cutting edge and designed sharpening angles. For the sliding cutting mode, the dependence of the useful resistance force on the feeding speed has been demonstrated at various sliding speed values and designed knife sharpening angles. The dependence of the transformed dimensionless sharpness of the knife on the angle of inclination of the cutting edge and the sliding speed has been established for different constructional sharpness values of the knife. The results of the study indicate that the useful resistance force is significantly reduced during the inclined and sliding cutting processes when compared with the normal cutting process, and a change in the pattern of fiber destruction, which significantly increases the cutting efficiency of cutting tools, is obtained.