Ultra-slow-light and dynamically quantitative optical storage modulation via quasi-BICs.

We achieve dynamically tunable dual quasi-bound states in the continuum (quasi-BICs) by implementing them in a silicon-graphene multilayer composite structure and utilize the quasi-BIC modes to achieve ultra-large group delays (velocity of light slows down 105 times), showing 2-3 orders of magnitude higher than the group delays of previous electromagnetically induced transparency modes. The double-layer graphene holds great tuning capability and leads to the dramatically reduced group delay from 1929.82 to 1.58 ps with only 100 meV. In addition, the log-linear variation rule of group delay with Fermi level (Ef) in the range of 0-10 meV is analyzed in detail, and the double-logarithmic function relationship between the group delay and quality factor (Q-factor) is theoretically verified. Finally, the quantitative modulation of the optical storage is further realized in this basis. Our research provides ideas for the reform and upgrading of slow optical devices.

Tunable High-Sensitivity Four-Frequency Refractive Index Sensor Based on Graphene Metamaterial.

As graphene-related technology advances, the benefits of graphene metamaterials become more apparent. In this study, a surface-isolated exciton-based absorber is built by running relevant simulations on graphene, which can achieve more than 98% perfect absorption at multiple frequencies in the MWIR (MediumWavelength Infra-Red (MWIR) band as compared to the typical absorber. The absorber consists of three layers: the bottom layer is gold, the middle layer is dielectric, and the top layer is patterned with graphene. Tunability was achieved by electrically altering graphene's Fermi energy, hence the position of the absorption peak. The influence of graphene's relaxation time on the sensor is discussed. Due to the symmetry of its structure, different angles of light source incidence have little effect on the absorption rate, leading to polarization insensitivity, especially for TE waves, and this absorber has polarization insensitivity at ultra-wide-angle degrees. The sensor is characterized by its tunability, polarisation insensitivity, and high sensitivity, with a sensitivity of up to 21.60 THz/refractive index unit (RIU). This paper demonstrates the feasibility of the multi-frequency sensor and provides a theoretical basis for the realization of the multi-frequency sensor. This makes it possible to apply it to high-sensitivity sensors.

Preparation of a Single-Cell Suspension from Mouse Carotid Arteries for Single-Cell Sequencing.

Carotid arteries are major blood vessels in the neck that supply blood and oxygen to the brain, but carotid stenosis occurs when carotid arteries are clogged by plaque. Revealing the cellular composition of the carotid artery at the single-cell level is essential for treating carotid atherosclerosis. However, there is no ready-to-use protocol for the preparation of single-cell suspensions from carotid arteries. To obtain a suitable protocol for the dissociation of normal carotid arteries at the single-cell level with less damage to cells, we designed a two-step digestion method by integrating the digestion process of collagenase/DNase and trypsin. Acridine orange/propidium iodide (AO/PI) dual-fluorescence counting was used to detect cell viability and concentration, and it was found that the single-cell suspension satisfied the requirements for single-cell sequencing, with the viability of cells over 85% and a high cell concentration. After single-cell data processing, a median of ~2500 transcripts per cell were detected in each carotid artery cell. Notably, a variety of cell types of the normal carotid artery, including vascular smooth muscle cells (VSMCs), fibroblasts, endothelial cells (ECs), and macrophages and dendritic cells (Mφ/DCs), were concurrently detectable. This protocol may be applied to prepare a single-cell suspension of blood vessels from other tissues with appropriate modifications.

Mixing Performance Analysis and Optimal Design of a Novel Passive Baffle Micromixer.

Micromixers, as crucial components of microfluidic devices, find widespread applications in the field of biochemistry. Due to the laminar flow in microchannels, mixing is challenging, and it significantly impacts the efficiency of rapid reactions. In this study, numerical simulations of four baffle micromixer structures were carried out at different Reynolds numbers (Re = 0.1, Re = 1, Re = 10, and Re = 100) in order to investigate the flow characteristics and mixing mechanism under different structures and optimize the micromixer by varying the vertical displacement of the baffle, the rotation angle, the horizontal spacing, and the number of baffle, and by taking into account the mixing intensity and pressure drop. The results indicated that the optimal mixing efficiency was achieved when the baffle's vertical displacement was 90 µm, the baffle angle was 60°, the horizontal spacing was 130 µm, and there were 20 sets of baffles. At Re = 0.1, the mixing efficiency reached 99.4%, and, as Re increased, the mixing efficiency showed a trend of, first, decreasing and then increasing. At Re = 100, the mixing efficiency was 97.2%. Through simulation analysis of the mixing process, the structure of the baffle-type micromixer was effectively improved, contributing to enhanced fluid mixing efficiency and reaction speed.

Bandwidth tunability of graphene absorption enhancement by hybridization of delocalized surface plasmon polaritons and localized magnetic plasmons.

The bandwidth-tunable absorption enhancement of monolayer graphene is theoretically studied in the near-infrared wavelengths. The monolayer graphene is placed on the silver substrate surface with a periodic array of one-dimensional slits. Two absorption peaks are found to result from the hybridization of delocalized surface plasmon polaritons and localized magnetic plasmons. The positions of absorption peaks are accurately predicted by a coupling model of double oscillators. The full width at half maximum of absorption peaks is largely tuned from about 1-200 nm by changing the array period of slits. The effect of the slit size on absorption peaks is also investigated in detail. Our work is promising in applications for photoelectric devices.

LPMO-supported saccharification of biomass: effects of continuous aeration of reaction mixtures with variable fractions of water-insoluble solids and cellulolytic enzymes.

BACKGROUND: High substrate concentrations and high sugar yields are important aspects of enzymatic saccharification of lignocellulosic substrates. The benefit of supporting the catalytic action of lytic polysaccharide monooxygenase (LPMO) through continuous aeration of slurries of pretreated softwood was weighed against problems associated with increasing substrate content (quantitated as WIS, water-insoluble solids, in the range 12.5-17.5%), and was compared to the beneficial effect on the saccharification reaction achieved by increasing the enzyme preparation (Cellic CTec3) loadings. Aerated reactions were compared to reactions supplied with N2 to assess the contribution of LPMO to the saccharification reactions. Analysis using 13C NMR spectroscopy, XRD, Simons' staining, BET analysis, and SEM analysis was used to gain further insights into the effects of the cellulolytic enzymes on the substrate under different reaction conditions. RESULTS: Although glucose production after 72 h was higher at 17.5% WIS than at 12.5% WIS, glucan conversion decreased with 24% (air) and 17% (N2). Compared to reactions with N2, the average increases in glucose production for aerated reactions were 91% (12.5% WIS), 70% (15.0% WIS), and 67% (17.5% WIS). Improvements in glucan conversion through aeration were larger (55-86%) than the negative effects of increasing WIS content. For reactions with 12.5% WIS, increased enzyme dosage with 50% improved glucan conversion with 25-30% for air and N2, whereas improvements with double enzyme dosage were 30% (N2) and 39% (air). Structural analyses of the solid fractions revealed that the enzymatic reaction, particularly with aeration, created increased surface area (BET analysis), increased disorder (SEM analysis), decreased crystallinity (XRD), and increased dye adsorption based on the cellulose content (Simons' staining). CONCLUSIONS: The gains in glucan conversion with aeration were larger than the decreases observed due to increased substrate content, resulting in higher glucan conversion when using aeration at the highest WIS value than when using N2 at the lowest WIS value. The increase in glucan conversion with double enzyme preparation dosage was smaller than the increase achieved with aeration. The results demonstrate the potential in using proper aeration to exploit the inherent capacity of LPMO in enzymatic saccharification of lignocellulosic substrates and provide detailed information about the characteristics of the substrate after interaction with cellulolytic enzymes.

Design of Surface Plasmon Resonance-Based D-Type Double Open-Loop Channels PCF for Temperature Sensing.

Here, we document a D-type double open-loop channel floor plasmon resonance (SPR) photonic crystal fiber (PCF) for temperature sensing. The grooves are designed on the polished surfaces of the pinnacle and backside of the PCF and covered with a gold (Au) film, and stomata are distributed around the PCF core in a progressive, periodic arrangement. Two air holes between the Au membrane and the PCF core are designed to shape a leakage window, which no longer solely averts the outward diffusion of Y-polarized (Y-POL) core mode energy, but also sets off its coupling with the Au movie from the leakage window. This SPR-PCF sensor uses the temperature-sensitive property of Polydimethylsiloxane (PDMS) to reap the motive of temperature sensing. Our lookup effects point out that these SPR-PCF sensors have a temperature sensitivity of up to 3757 pm/°C when the temperature varies from 5 °C to 45 °C. In addition, the maximum refractive index sensitivity (RIS) of the SPR-PCF sensor is as excessive as 4847 nm/RIU. These proposed SPR-PCF temperature sensors have an easy nanostructure and proper sensing performance, which now not solely improve the overall sensing performance of small-diameter fiber optic temperature sensors, but also have vast application prospects in geo-logical exploration, biological monitoring, and meteorological prediction due to their remarkable RIS and exclusive nanostructure.

Design of a Penta-Band Graphene-Based Terahertz Metamaterial Absorber with Fine Sensing Performance.

This paper presents a new theoretical proposal for a surface plasmon resonance (SPR) terahertz metamaterial absorber with five narrow absorption peaks. The overall structure comprises a sandwich stack consisting of a gold bottom layer, a silica medium, and a single-layer patterned graphene array on top. COMSOL simulation represents that the five absorption peaks under TE polarization are at fI = 1.99 THz (95.82%), fⅡ = 6.00 THz (98.47%), fⅢ = 7.37 THz (98.72%), fⅣ = 8.47 THz (99.87%), and fV = 9.38 THz (97.20%), respectively, which is almost consistent with the absorption performance under TM polarization. In contrast to noble metal absorbers, its absorption rates and resonance frequencies can be dynamically regulated by controlling the Fermi level and relaxation time of graphene. In addition, the device can maintain high absorptivity at 0~50° in TE polarization and 0~40° in TM polarization. The maximum refractive index sensitivity can reach SV = 1.75 THz/RIU, and the maximum figure of merit (FOM) can reach FOMV = 12.774 RIU-1. In conclusion, our design has the properties of dynamic tunability, polarization independence, wide-incident-angle absorption, and fine refractive index sensitivity. We believe that the device has potential applications in photodetectors, active optoelectronic devices, sensors, and other related fields.

Near-perfect quantitatively tunable Q factors of quasi-bound states in the continuum via material-based thermal-optic perturbations.

We successfully achieved high-Q dual-band quasi-bound states in the continuum (BICs) by introducing geometrical perturbations and thermally induced material perturbations into silicon half-disk nanodimers. Importantly, it is found that the Q factor obtained from the thermally induced material perturbations fits better with the inverse quadratic function of the asymmetry relation than that of the geometrical-perturbations-based system. Notably, we demonstrated that changes occurring at the sub-K scale can enable the simultaneous realization of the full width at half maximum offset distance for quasi-BICs and a maximum contrast ratio exceeding 44 dB. Our research provides novel, to the best of our knowledge, insights for potential applications in nano-lasers, temperature sensors, and infrared imaging.

Multipolar silicon-based resonant meta-surface for electro-optical modulation and sensing.

A multipolar silicon-based resonant meta-surface scheme is proposed and numerically presented via intercalating oblique slits into the silicon patches, leading to an ultra-sharp resonant spectrum via the excitation of electric and magnetic quadrupoles and their hybridization coupling. High-performance electro-optical modulator is demonstrated, showing a spectrally shifted modulation sensitivity up to 1.546 nm/V. Moreover, novel, to the best of our knowledge, optical sensing for ion solution concentration with the detection limitation down to 5.15 × 10-3 is demonstrated as another application. These findings provide an impressive strategy for resonant silicon-based nano-photonics and opto-electronic devices.

Endothelial CCRL2 induced by disturbed flow promotes atherosclerosis via chemerin-dependent ß2 integrin activation in monocytes.

AIMS: Chemoattractants and their cognate receptors are essential for leucocyte recruitment during atherogenesis, and atherosclerotic plaques preferentially occur at predilection sites of the arterial wall with disturbed flow (d-flow). In profiling the endothelial expression of atypical chemoattractant receptors (ACKRs), we found that Ackr5 (CCRL2) was up-regulated in an endothelial subpopulation by atherosclerotic stimulation. We therefore investigated the role of CCRL2 and its ligand chemerin in atherosclerosis and the underlying mechanism. METHODS AND RESULTS: By analysing scRNA-seq data of the left carotid artery under d-flow and scRNA-seq datasets GSE131776 of ApoE-/- mice from the Gene Expression Omnibus database, we found that CCRL2 was up-regulated in one subpopulation of endothelial cells in response to d-flow stimulation and atherosclerosis. Using CCRL2-/-ApoE-/- mice, we showed that CCRL2 deficiency protected against plaque formation primarily in the d-flow areas of the aortic arch in ApoE-/- mice fed high-fat diet. Disturbed flow induced the expression of vascular endothelial CCRL2, recruiting chemerin, which caused leucocyte adhesion to the endothelium. Surprisingly, instead of binding to monocytic CMKLR1, chemerin was found to activate ß2 integrin, enhancing ERK1/2 phosphorylation and monocyte adhesion. Moreover, chemerin was found to have protein disulfide isomerase-like enzymatic activity, which was responsible for the interaction of chemerin with ß2 integrin, as identified by a Di-E-GSSG assay and a proximity ligation assay. For clinical relevance, relatively high serum levels of chemerin were found in patients with acute atherothrombotic stroke compared to healthy individuals. CONCLUSIONS: Our findings indicate that d-flow-induced CCRL2 promotes atherosclerotic plaque formation via a novel CCRL2-chemerin-ß2 integrin axis, providing potential targets for the prevention or therapeutic intervention of atherosclerosis.

The role of blood flow in vessel remodeling and its regulatory mechanism during developmental angiogenesis.

Vessel remodeling is essential for a functional and mature vascular network. According to the difference in endothelial cell (EC) behavior, we classified vessel remodeling into vessel pruning, vessel regression and vessel fusion. Vessel remodeling has been proven in various organs and species, such as the brain vasculature, subintestinal veins (SIVs), and caudal vein (CV) in zebrafish and yolk sac vessels, retina, and hyaloid vessels in mice. ECs and periendothelial cells (such as pericytes and astrocytes) contribute to vessel remodeling. EC junction remodeling and actin cytoskeleton dynamic rearrangement are indispensable for vessel pruning. More importantly, blood flow has a vital role in vessel remodeling. In recent studies, several mechanosensors, such as integrins, platelet endothelial cell adhesion molecule-1 (PECAM-1)/vascular endothelial cell (VE-cadherin)/vascular endothelial growth factor receptor 2 (VEGFR2) complex, and notch1, have been shown to contribute to mechanotransduction and vessel remodeling. In this review, we highlight the current knowledge of vessel remodeling in mouse and zebrafish models. We further underline the contribution of cellular behavior and periendothelial cells to vessel remodeling. Finally, we discuss the mechanosensory complex in ECs and the molecular mechanisms responsible for vessel remodeling.

Spatial and frequency-selective optical field coupling absorption in an ultra-thin random metasurface.

Simplified thin-film structures with the capability of spatial and frequency-selective optical field coupling and absorption are desirable for nanophotonics. Herein, we demonstrate the configuration of a 200-nm-thick random metasurface formed by refractory metal nanoresonators, showing near-unity absorption (absorptivity > 90%) covering the visible and near-infrared range (0.380-1.167 µm). Importantly, the resonant optical field is observed to be concentrated in different spatial areas according to different frequencies, paving a feasible way to artificially manipulate spatial coupling and optical absorption via the spectral frequency. The methods and conclusions derived in this work are applicable throughout a wide energy range and hold applications for frequency-selective nanoscale optical field manipulation.

Sema7A protects against high-fat diet-induced obesity and hepatic steatosis by regulating adipo/lipogenesis.

OBJECTIVE: Obesity and related diseases are becoming a growing risk for public health around the world due to the westernized lifestyle. Sema7A, an axonal guidance molecule, has been known to play a role in neurite growth, bone formation, and immune regulation. Whether Sema7A participates in obesity and metabolic diseases is unknown. As several SNPs in SEMA7A and its receptors were found to correlate with BMI and metabolic parameters in the human population, we investigated the potential role of Sema7A in obesity and hepatic steatosis. METHODS: GWAS and GEPIA database was used to analyze SNPs in SEMA7A and the correlation of Sema7A expression with lipid metabolism related genes. Sema7A-/- mice and recombinant Sema7A (rSema7A) were used to study the role of Sema7A in HFD-induced obesity and hepatic steatosis. Adipose tissue-derived mesenchymal stem cells (ADSCs) were used to examine the role of Sema7A in adipogenesis, lipogenesis and downstream signaling. RESULTS: Deletion of Sema7A aggravated HFD-induced obesity. Sema7A deletion enhanced adipogenesis in both subcutaneous and visceral ADSCs, while the addition of rSema7A inhibited adipogenesis of ADSCs and lipogenesis of differentiated mature adipocytes. Sema7A inhibits adipo/lipogenesis potentially through its receptor integrin ß1 and downstream FAK signaling. Importantly, administration of rSema7A had protective effects against diet-induced obesity in mice. In addition, deletion of Sema7A led to increased hepatic steatosis and insulin resistance in mice. CONCLUSIONS: Our findings reveal a novel inhibitory role of Sema7A in obesity and hepatic steatosis, providing a potential new therapeutic target for obesity and metabolic diseases.

Comparison of solid and liquid fractions of pretreated Norway spruce as reductants in LPMO-supported saccharification of cellulose.

The role of lignin in enzymatic saccharification of cellulose involving lytic polysaccharide monooxygenase (LPMO) was investigated in experiments with the solid and liquid fractions of pretreated Norway spruce from a biorefinery demonstration plant using hydrothermal pretreatment and impregnation with sulfur dioxide. Pretreated biomass before and after enzymatic saccharification was characterized using HPAEC, HPLC, Py-GC/MS, 2D-HSQC NMR, FTIR, and SEM. Chemical characterization indicated that relatively harsh pretreatment conditions resulted in that the solid phase contained no or very little hemicellulose but considerable amounts of pseudo-lignin, and that the liquid phase contained a relatively high concentration (∼5 g/L) of lignin-derived phenolics. As judged from reactions continuously supplied with either air or nitrogen gas, lignin and lignin fragments from both the solid and the liquid phases efficiently served as reductants in LPMO-supported saccharification. When air was used to promote LPMO activity, the enzymatic conversion of cellulose after 72 h was 25% higher in reactions with pretreated solids and buffer, and 14% higher in reactions with pretreatment liquid and microcrystalline cellulose. Research in this area is useful for designing efficient saccharification steps in biochemical conversion of lignocellulosic biomass.

Ultra-broadband and completely modulated absorption enhancement of monolayer graphene in a near-infrared region.

Achieving ultra-broadband and completely modulated absorption enhancement of monolayer graphene in near-infrared region is practically important to design graphene-based optoelectronic devices, however, which remains a challenge. In this work, by spectrally designing multiple magnetic plasmon resonance modes in metamaterials to be adjacent to each other, near-infrared light absorption in monolayer graphene is greatly improved to have an averaged absorption efficiency exceeding 50% in a very broad absorption bandwidth of about 800 nm. Moreover, by exerting an external bias voltage on graphene to change Fermi energy of graphene, the ultra-broadband absorption enhancement of monolayer graphene exhibits an excellent tunability, which has a nearly 100% modulation depth and an electrical switching property. This work is promising for applications in near-infrared photodetectors, amplitude modulators of electromagnetic waves, etc.

Single-cell transcriptional profiling of human carotid plaques reveals a subpopulation of endothelial cells associated with stroke incidences.

The differences in plaque histology between symptomatic and asymptomatic patients have been widely accepted. Whether there is a heterogeneity of cells between symptomatic and asymptomatic plaques remains largely unclear. To reveal the potential heterogeneity within different plaques, which may contribute to different stroke incidences, we obtained the scRNA-seq data from symptomatic and asymptomatic patients and identified eight cell types present in plaques. Further analysis of endothelial cells (ECs) revealed three distinct EC subpopulations appeared to be endowed with specific biological functions such as antigen processing and presentation, cell adhesion, and smooth muscle cell proliferation. Of note, the differentially expressed genes of the EC 2 subpopulation showed that the genes involved in cell adhesion were up-regulated in asymptomatic plaques compared to symptomatic plaques. Integrating the data of intraplaque haemorrhage and plaque stability, the 5th top-enriched biological process was cell adhesion in the stable or non-haemorrhaged plaques compared to unstable plaques or haemorrhaged plaques. Among these cell adhesion-related genes, the intersection gene AOC3 may play a vital role in plaque haemorrhage and plaque stability. Targeting cell adhesion and the specialized genes may provide potential new therapeutic directions to prevent asymptomatic patients from stroke.

TET1s deficiency exacerbates oscillatory shear flow-induced atherosclerosis.

Background: TET1 has been implicated in regulating inflammation and cardiovascular disease, but a newly discovered short isoform of TET1 (termed TET1s) exhibits higher expression in adult tissues than full-length TET1. However, the precise role of TET1 in cardiovascular disease remains undefined. Methods and Results: Based on TET1-/- knockout mice (with deletion of both TET1 and TET1s ) and TET1cs/cs mice (with deletion of only TET1), we found that TET1s deletion in TET1-/- mice resulted in more serious atherosclerotic lesions in the whole aorta than TET1cs/cs in the ApoE-/- background mice fed a high-fat diet. Atherosclerotic lesions with Oil red staining were dramatically localized in the aortic arch, abdominal aorta and ligated LCA, where they were exposed to OSS. Furthermore, the OSS-induced depression of TET1s in vitro and in vivo increased inflammatory cell and red blood cell infiltration into the subendothelial layer by impairing the vascular intimal barrier. TET1s upregulation enhanced vascular endothelial barrier function by increasing gap protein connexin 40 (CX40) expression as measured by RNA-seq and was confirmed by CX40 knockdown. TET1s interaction with Sin3a increased the global and CX40 promoter histone H3K27 acetylation levels, but not DNA methylation, to induce CX40 expression. Conclusions: These data demonstrate the unexpected discovery that laminar shear stress induces TET1s expression to protect the vascular endothelial barrier by increasing CX40 expression in ECs and that TET1s overexpression may be the core step for OSS-induced atherosclerosis therapy.

The Light Absorption Enhancement in Graphene Monolayer Resulting from the Diffraction Coupling of Surface Plasmon Polariton Resonance.

In this study, we investigate a physical mechanism to improve the light absorption efficiency of graphene monolayer from the universal value of 2.3% to about 30% in the visible and near-infrared wavelength range. The physical mechanism is based on the diffraction coupling of surface plasmon polariton resonances in the periodic array of metal nanoparticles. Through the physical mechanism, the electric fields on the surface of graphene monolayer are considerably enhanced. Therefore, the light absorption efficiency of graphene monolayer is greatly improved. To further confirm the physical mechanism, we use an interaction model of double oscillators to explain the positions of the absorption peaks for different array periods. Furthermore, we discuss in detail the emerging conditions of the diffraction coupling of surface plasmon polariton resonances. The results will be beneficial for the design of graphene-based photoelectric devices.