Phase controlled homodyne infrared near-field microscopy and spectroscopy reveal inhomogeneity within and among individual boron nitride nanotubes.

We propose a practical method to obtain near-field infrared absorption spectra in apertureless near-field scanning optical microscopy (aNSOM) through homodyne detection with a specific choice of reference phase. The underlying mechanism of the method is illustrated by theoretical and numeric models to show its ability to obtain absorptive rather than dispersive profiles in near-field infrared vibrational microscopy. The proposed near-field nanospectroscopic method is applied to obtain infrared spectra from regions of individual multiwall boron nitride nanotubes (BNNTs) in spatial regions smaller than the diffraction limit of the light source. The spectra suggest variations in interwall spacing within the individual tubes probed.

Diameter-dependent bending modulus of individual multiwall boron nitride nanotubes.

The mechanical properties of individual multiwall boron nitride nanotubes (MWBNNTs) synthesized by a growth-vapor-trapping chemical vapor deposition method are investigated by a three-point bending technique via atomic force microscopy. Multiple locations on suspended tubes are probed in order to determine the boundary conditions of the supported tube ends. The bending moduli (EB) calculated for 20 tubes with diameters ranging from 18 to 58 nm confirm the exceptional mechanical properties of MWBNNTs, with an average EB of 760 ± 30 GPa. For the first time, the bending moduli of MWBNNTs are observed to increase with decreasing diameter, ranging from 100 ± 20 GPa to as high as 1800 ± 300 GPa. This diameter dependence is evaluated by Timoshenko beam theory. The Young's modulus and shear modulus were determined to be 1800 ± 300 and 7 ± 1 GPa, respectively, for a trimmed data set of 16 tubes. The low shear modulus of MWBNNTs is the reason for the detected diameter-dependent bending modulus and is likely due to the presence of interwall shearing between the crystalline and faceted helical nanotube structures of MWBNNTs.

Imaging secondary structure of individual amyloid fibrils of a ß2-microglobulin fragment using near-field infrared spectroscopy.

Amyloid fibril diseases are characterized by the abnormal production of aggregated proteins and are associated with many types of neuro- and physically degenerative diseases. X-ray diffraction techniques, solid-state magic-angle spinning NMR spectroscopy, circular dichroism (CD) spectroscopy, and transmission electron microscopy studies have been utilized to detect and examine the chemical, electronic, material, and structural properties of amyloid fibrils at up to angstrom spatial resolution. However, X-ray diffraction studies require crystals of the fibril to be analyzed, while other techniques can only probe the bulk solution or solid samples. In the work reported here, apertureless near-field scanning infrared microscopy (ANSIM) was used to probe the secondary structure of individual amyloid fibrils made from an in vitro solution. Simultaneous topographic and infrared images of individual amyloid fibrils synthesized from the #21-31 peptide fragment of ß(2)-microglobulin were acquired. Using this technique, IR spectra of the amyloid fibrils were obtained with a spatial resolution of less than 30 nm. It is observed that the experimental scattered field spectrum correlates strongly with that calculated using the far-field absorption spectrum. The near-field images of the amyloid fibrils exhibit much lower scattering of the IR radiation at approximately 1630 cm(-1). In addition, the near-field images also indicate that composition and/or structural variations among individual amyloid fibrils were present.

Insights into the composition, morphology, and formation of the calcareous shell of the serpulid Hydroides dianthus.

To date, the calcareous tubes of serpulid marine worms have not been studied extensively in a biomineralization context. The structure and composition of the tube shell and adhesive cement of the marine tubeworm Hydroides dianthus were studied using a variety of characterization techniques, including powder XRD, FTIR, SEM, EDX, and AFM. The tube and cement were determined to be inorganic-organic composite materials, consisting of inorganic aragonite (CaCO(3)) and Mg-calcite ((Ca(0.8)Mg(0.2))CO(3)) crystals, and both soluble and insoluble organic matrices (SOM and IOM). SEM imaging revealed a variety of crystal morphologies. AFM nanoindentation of the inorganic components yielded Young's moduli of approximately 20GPa in the wet state, and approximately 50GPa in the dry state. Amino acid analysis of the SOM indicated substantial amounts of acidic and non-polar neutral amino acids. Part of the insoluble organic tube lining was identified as being composed of collagen-containing fibres aligned in a criss-crossed structure. The SOM and organic tube lining were found to contain carboxylated and sulphated polysaccharides. In an artificial seawater solution, the SOM and the organic tube lining mediated CaCO(3) mineralization in vitro.

Nanoscale structures and mechanics of barnacle cement.

Polymerized barnacle glue was studied by atomic force microscopy (AFM), scanning electron microscopy (SEM), Fourier transform infrared (FTIR) spectroscopy and chemical staining. Nanoscale structures exhibiting rod-shaped, globular and irregularly-shaped morphologies were observed in the bulk cement of the barnacle Amphibalanus amphitrite (=Balanus amphitrite) by AFM. SEM coupled with energy dispersive X-ray (EDX) provided chemical composition information, making evident the organic nature of the rod-shaped nanoscale structures. FTIR spectroscopy gave signatures of beta-sheet and random coil conformations. The mechanical properties of these nanoscale structures were also probed using force spectroscopy and indentation with AFM. Indentation data yielded higher elastic moduli for the rod-shaped structures when compared with the other structures in the bulk cement. Single molecule AFM force-extension curves on the matrix of the bulk cement often exhibited a periodic sawtooth-like profile, observed in both the extend and retract portions of the force curve. Rod-shaped structures stained with amyloid protein-selective dyes (Congo red and thioflavin-T) revealed that about 5% of the bulk cement were amyloids. A dominant 100 kDa cement protein was found to be mechanically agile, using repeating hydrophobic structures that apparently associate within the same protein or with neighbors, creating toughness on the 1-100 nm length scale.