Optimal Synthesis of Novel Phosphonic Acid Modified Diatomite Adsorbents for Effective Removal of Uranium(VI) Ions from Aqueous Solutions.

The authors synthesized a series of functionalized diatomite-based materials and assessed their U(VI) removal performance. Phosphor-derivative-modified diatomite adsorbents were synthesized by the three-route procedures: polymerisation (DIT-Vin-PAin), covalent (DIT-Vin-PAcov), and non-covalent (DIT-PA) immobilization of the functional groups. The effects of the diatomite modification have been studied using powder XRD, solid state NMR, FTIR spectroscopy, electronic microscopy, EDX, acid-base titrations, etc. The maximum adsorption capacities of DIT-Vin-PAcov, DIT-PA, and DIT-Vin-PAin samples were 294.3 mg/g, 253.8 mg/g, and 315.9 mg/g, respectively, at pH0 = 9.0. The adsorption amount of U(VI) ions using the prepared DIT-Vin-PAin was 95.63%, which is higher compared with that of the natural diatomite at the same concentration. The adsorption studies demonstrated that the phosphonic and hydroxyl groups on the surface of the diatomite played pivotal roles in the U(VI) adsorption. The U(VI) ions as a "hard" Lewis acid could easily form bonds with the "hard" donor P-containing ligands, so that the as-prepared DIT-Vin-PAin sample had excellent adsorption properties. The monolayer adsorption of the analyte on the surface of the raw diatomite and DIT-PA was observed. It was found from the thermodynamic parameters that the uptake of the U(VI) ions by the obtained adsorbents was a spontaneous process with an endothermic effect. Findings of the present work highlight the potential for using modified diatomite as effective and reusable adsorbents for the extraction of U(VI) in the waste, river, and tap waters with satisfactory results.

Cleavage of Organosiloxanes with Dimethyl Carbonate: A Mild Approach To Graft-to-Surface Modification.

In this work, we explore the depolymerization of poly(dimethylsiloxane) (PDMS-100) and poly(methylphenylsiloxane) (PMPS) using dimethyl carbonate (DMC) and develop a surface functionalization method by utilizing the DMC-imparted active methoxy end groups of the partially depolymerized polysiloxanes. The efficiency of dimethyl carbonate as a reagent for organosiloxane cleavage was confirmed by means of 1H NMR spectroscopy, size-exclusion chromatography, and viscosity measurements. The reaction of fumed silica with organosiloxanes (PMPS, PDMS-50) in the presence of DMC was investigated using the ζ-potential, 29Si and 13C solid-state NMR spectroscopy, IR spectroscopy, CHN analysis, contact angle goniometry, thermogravimetric analysis, scanning and transmission electron microscopy (TEM), and rheology. It was found that the interaction of PMPS/DMC with an SiO2 surface produced hydrophobic and thermally stable moieties (up to 550 °C) with a densely packed (average 2.2 groups/nm2) alkylsiloxane network for SiO2/PMPS + DMC in comparison with SiO2/PMPS (average 1.4 groups/nm2). Surface functionalization was successfully attained at a relatively moderate temperature of 200 °C. Scanning electron microscopy data show that the average size of aggregates of PMPS/DMC-modified silica nanoparticles is smaller than that of the initial silica and silica modified with neat PMPS. TEM images reveal uniform distribution of the PMPS/DMC mixture across the SiO2 surface. Rheology studies show thixotropic behavior in industrial oil (I-40A), a fully reversible nanostructure and shorter structure recovery time for fumed silica modified in the presence of DMC.

A New Route for Preparation of Hydrophobic Silica Nanoparticles Using a Mixture of Poly(dimethylsiloxane) and Diethyl Carbonate.

Organosilicon layers chemically anchored on silica surfaces show high carbon content, good thermal and chemical stability and find numerous applications as fillers in polymer systems, thickeners in dispersing media, and as the stationary phases and carriers in chromatography. Methyl-terminated poly(dimethylsiloxanes) (PDMSs) are typically considered to be inert and not suitable for surface modification because of the absence of readily hydrolyzable groups. Therefore, in this paper, we report a new approach for surface modification of silica (SiO2) nanoparticles with poly(dimethylsiloxanes) with different lengths of polymer chains (PDMS-20, PDMS-50, PDMS-100) in the presence of diethyl carbonate (DEC) as initiator of siloxane bond splitting. Infrared spectroscopy (IR), elemental analysis (CHN), transmission electron microscopy (TEM), atomic force microscopy (AFM), rotational viscosity and contact angle of wetting were employed for the characterization of the raw fumed silica and modified silica nanoparticles. Elemental analysis data revealed that the carbon content in the grafted layer is higher than 8 wt % for all modified silicas, but it decreases significantly after sample treatment in polar media for silicas which were modified using neat PDMS. The IR spectroscopy data indicated full involvement of free silanol groups in the chemisorption process at a relatively low temperature (220 °C) for all resulting samples. The contact angle studies confirmed hydrophobic surface properties of the obtained materials. The rheology results illustrated that fumed silica modified with mixtures of PDMS-x/DEC exhibited thixotropic behavior in industrial oil (I-40A), and exhibited a fully reversible nanostructure and shorter structure recovery time than nanosilicas modified with neat PDMS. The obtained results from AFM and TEM analysis revealed that the modification of fumed silica with mixtures of PDMS-20/DEC allows obtaining narrow particle size distribution with uniform dispersity and an average particle size of 15⁻17 nm. The fumed silica nanoparticles chemically modified with mixtures of PDMS-x/DEC have potential applications such as nanofillers of various polymeric systems, thickeners in dispersing media, and additives in coatings.

Infrared, Raman and Magnetic Resonance Spectroscopic Study of SiO2:C Nanopowders.

Optical and magnetic properties of SiO2:C nanopowders obtained by chemical and thermal modification of fumed silica were studied by Fourier transform infrared spectroscopy, Raman, continuous wave (CW) electron paramagnetic resonance (EPR), echo-detected EPR and pulsed electron nuclear double resonance (ENDOR) spectroscopy. Two overlapping signals of Lorentzian lineshape were detected in CW EPR spectra of the initial SiO2:C. The EPR signal at g = 2.0055(3) is due to the silicon dangling bonds, which vanishes after thermal annealing, and the second EPR signal at g = 2.0033(3) was attributed to the carbon-related defect (CRD). The annealing of the SiO2:C samples gives rise to the increase of the CRD spin density and shift to the higher g-values due to the appearance of the oxygen in the vicinity of the CRD. Based on the temperature-dependent behavior of the CRD EPR signal intensity, linewidth and resonance field position we have attributed it to the spin system with non-localized electrons hopping between neighboring carbon dangling bonds, which undergo a strong exchange interaction with a localized spin system of carbon nanodots. The observed motional narrowing of the CRD EPR signal in the temperature interval from 4 to 20 K indicates that electrons are mobile at 4 K which can be explained by a quantum character of the conductivity in the vicinity of the carbon layer. The electrons trapped in quantum wells move from one carbon nanodot to another by hopping process through the energy barrier. The fact that echo-detected EPR signal at g = 2.0035(3) was observed in SiO2:C sample annealed at T ann ≥ 700 °C serves as evidence that non-localized electrons coexist with localized electrons that have the superhyperfine interaction with surrounding 13C and 29Si nuclei located at the SiO2:C interface. The presence of the superhyperfine interaction of CRD with 1H nuclei indicates the existence of hydrogenated regions in SiO2:C sample.

Electrokinetic Properties of the Pristine and Oxidized MWCNT Depending on the Electrolyte Type and Concentration.

Electrostatic stabilization is reduced in its efficiency in an electrolyte-containing environment. The effect of electrolyte concentration is mostly described as negative factor for dispersion stabilization. Usually, zeta potential and physical stability decrease at increasing electrolyte concentration. The purpose of the present study was to measure the surface properties of nanotubes in aqueous solution of monovalent electrolytes at different concentration. Characteristics such as size distribution, surface chemistry, surface charge, and dispersability in aqueous phase have been identified. Hydrodynamic size and zeta potential in aqueous multiwalled carbon nanotube (MWCNT) suspensions were determined at different pH with the desired concentrations of electrolyte of the cationic group (NaCl, KCl, CsCl) and the anionic group (NaClO4). The correlations between the response of the surface functionality of pristine and oxidized multiwalled carbon nanotubes and electrical double layer (EDL) forming at different ionic environments in the vicinity of a nanotube surface were determined. The nanotube dispersion stabilization was found to be more affected by ion size and pH medium then electrolyte concentration. The data obtained confirms the predominant role of surface reactions. The most stable dispersion of nanotubes was achieved in KCl electrolyte solution at less negative charge of the surface.