ZnO Nanoparticles Enhance the Antimicrobial Properties of Two-Sided-Coated Cotton Textile.

Cotton textiles improved with metal oxide nanoparticles acquire additional features that may enhance their action against antimicrobial-resistant pathogens due to the unique properties and characteristics of the nanoparticles. The main objective of this work is to evaluate the antimicrobial features of two-sided-coated cotton textiles with ZnO nanoparticles. Nanoparticles were deposited using green chemistry technology with low-temperature oxygen plasma. ZnO particles formed stable structures on textile fibers. The optimal deposition parameters (150 W plasma power, 120 min immersion time) achieved the best effects against Gram-negative and Gram-positive bacteria and microscopic fungi. Two-sided-coated cotton with ZnO nanoparticles showed high antibacterial action on Gram-negative and Gram-positive bacteria. Modification with zinc oxide inhibited the growth of Candida albicans by more than half.

Nanoparticle Effects on Ice Plant Mineral Accumulation under Different Lighting Conditions and Assessment of Hazard Quotients for Human Health.

Nanotechnologies can improve plant growth, protect it from pathogens, and enrich it with bioactive and mineral substances. In order to fill the lack of knowledge about the combined environmental effects of lighting and nanoparticles (NPs) on plants, this study is designed to investigate how different HPS and LED lighting combined with CuO and ZnO NPs influence the elemental composition of ice plants (Mesembryanthemum crystallinum L.). Plants were grown in hydroponic systems with LED and HPS lighting at 250 ± 5 µmol m-2 s-1 intensity, sprayed with aqueous suspensions of CuO (40 nm, 30 ppm) and ZnO (35-45 nm, 800 ppm) NPs; their elemental composition was measured using an ICP-OES spectrometer and hazard quotients were calculated. LED lighting combined with the application of ZnO NPs significantly affected Zn accumulation in plant leaves. Cu accumulation was higher when plants were treated with CuO NPs and HPS illumination combined. The calculated hazard quotients showed that the limits are not exceeded when applying our selected concentrations and growth conditions on ice plants. In conclusion, ice plants had a more significant positive effect on the accumulation of macro- and microelements under LED lighting than HPS. NPs had the strongest effect on the increase in their respective microelements.

Development of Antibacterial Cotton Textiles by Deposition of Fe2O3 Nanoparticles Using Low-Temperature Plasma Sputtering.

Antibacterial textiles can help prevent infections from antimicrobial-resistant pathogens without using antibiotics. This work aimed to enhance the cotton fabric's antimicrobial properties by depositing Fe2O3 nanoparticles on both sides of its surface. The nanoparticles were deposited using low-temperature plasma technology in a pure oxygen atmosphere, which is environmentally friendly. The Fe2O3 nanoparticles formed clusters on the fabric surface, rather than thin films that could reduce the airflow of the textile. The optimal conditions for the nanoparticle deposition were 200 W of plasma power, 120 min of immersion time, and 5 cm of Fe cathode-textile sample distance. The received antimicrobial textile was tested and the high efficiency of developed materials were successfully demonstrated against 16 microbial strains (Gram-positive and Gram-negative bacteria and fungi).

Antimicrobial Properties of CuO Particles Deposited on a Medical Mask.

Medical face masks help to reduce the transmission of pathogens, however, the number of infections caused by antimicrobial-resistant pathogens continues to increase. The aim of this study was to investigate the antimicrobial effect of an experimental medical mask layer coated with copper oxide using an environmentally friendly non-thermal physical vapour deposition approach. Pure CuO nanoparticles were successfully deposited on the middle layer of a face mask. The particles were distributed in different size clusters (starting from less than 100 nm dots going up to about 1 µm cluster-like structures). The CuO clusters did not form uniform films, which could negatively influence airflow during use of the mask. We investigated the antimicrobial properties of the experimental mask layer coated with CuO NPs using 17 clinical and zoonotic strains of gram-negative, gram-positive, spore-forming bacteria and yeasts, during direct and indirect contact with the mask surface. The effectiveness of the coated mask layer depended on the deposition duration of CuO. The optimal time for deposition was 30 min, which ensured a bactericidal effect for both gram-positive and gram-negative bacteria, including antimicrobial-resistant strains, using 150 W power. The CuO NPs had little or no effect on Candida spp. yeasts.

Visible-Light-Driven Photocatalytic Inactivation of Bacteria, Bacteriophages, and Their Mixtures Using ZnO-Coated HDPE Beads as Floating Photocatalyst.

Semiconductor materials used as photocatalysts are considered among the most effective ways to treat biologically polluted water. Certainly, efficiency depends on the selection of photocatalyst and its substrate, as well as the possibility of its application in a broader spectrum of light. In this study, a reactive magnetron sputtering technique was applied for the immobilisation of ZnO photocatalyst on the surface of HDPE beads, which were selected as the buoyant substrates for enhanced photocatalytic performance and easier recovery from the treated water. Moreover, the study compared the effect on the inactivation of the microorganism between ZnO-coated HDPE beads without Ni and with Ni underlayer. Crystal structure, surface morphology, and chemical bonds of as-deposited ZnO films were investigated by X-ray diffraction, scanning electron microscopy, and X-ray photoelectron spectroscopy, respectively. Visible-light-induced photocatalytic treatment was performed on the Gram-negative and Gram-positive bacteria and bacteriophages PRD1, T4, and their mixture. Higher bacteria inactivation efficiency was obtained using the ZnO photocatalyst with Ni underlayer for the treatment of S. Typhimurium and M. Luteus mixtures. As for infectivity of bacteriophages, T4 alone and in the mixture with PRD1 were more affected by the produced photocatalyst, compared with PRD1.

Photocatalytic Inactivation of Salmonella typhimurium by Floating Carbon-Doped TiO2 Photocatalyst.

Photocatalysis application is considered as one of the most highly promising techniques for the reduction in wastewater pollution. However, the majority of highly efficient photocatalyst materials are obtained as fine powders, and this causes a lot of photocatalyst handling and reusability issues. The concept of the floating catalyst proposes the immobilization of a photocatalytic (nano)material on relatively large floating substrates and is considered as an encouraging way to overcome some of the most challenging photocatalysis issues. The purpose of this study is to examine floating photocatalyst application for Salmonella typhimurium bacteria inactivation in polluted water. More specifically, high-density polyethylene (HDPE) beads were used as a photocatalyst support for the immobilization of carbon-doped TiO2 films forming floating photocatalyst structures. Carbon-doped TiO2 films in both amorphous and anatase forms were deposited on HDPE beads using the low-temperature magnetron sputtering technique. Bacteria inactivation, together with cycling experiments, revealed promising results by decomposing more than 95% of Salmonella typhimurium bacteria in five consecutive treatment cycles. Additionally, a thorough analysis of the deposited carbon-doped TiO2 film was performed including morphology, elemental composition and mapping, structure, and depth profiling. The results demonstrate that the proposed method is a suitable technique for the formation of high-quality photocatalytic active films on thermal-sensitive substrates.

The Using of Concrete Wash Water from Ready Mixed Concrete Plants in Cement Systems.

Concrete plants accumulate large amounts of concrete wash water. This water, which pH is highly alkaline, has a negative impact on the environment. Its reuse in fresh concrete slightly reduces its mechanical properties. The combination of concrete wash water and zeolitic by-product led to an increase of 4.6% in the compressive strength at 7 days hydration and up to 30% at 28 days hydration. The same combination led to the denser microstructure compared to the samples made with concrete wash water. This could be explained by the pozzolanic reaction of the zeolitic by-product. The complex chemical reactions of cement, zeolitic by-product, and fines presented in the concrete wash water occurred. Therefore, it was suggested the reusing method of concrete wash water together with zeolitic by-product in the fresh concrete mixtures by substituting some amount of tap water with concrete wash water. In this way, the consumption of tap water is possible to reduce in cement systems.

Effects of carbon nanotubes on expanded glass and silica aerogel based lightweight concrete.

This study is aimed to investigate the effect of carbon nanotubes on the properties of lightweight aggregate concrete containing expanded glass and silica aerogel. Combinations of expanded glass (55%) and hydrophobic silica aerogel particles (45%) were used as lightweight aggregates. Carbon nanotubes were sonicated in the water with polycarboxylate superplasticizer by ultrasonication energy for 3 min. Study results show that incorporating multi-wall carbon nanotubes significantly influences the compressive strength and microstructural performance of aerogel based lightweight concrete. The addition of carbon nanotubes gained almost 41% improvement in compressive strength. SEM image of lightweight concrete shows a homogeneous dispersal of carbon nanotubes within the concrete structure. SEM image of the composite shows presence of C-S-H gel surrounding the carbon nanotubes, which confirms the cites of nanotubes for the higher growth of C-S-H gel. Besides, agglomeration of carbon nanotubes and the presence of ettringites was observed in the transition zone between the silica aerogel and cementitious materials. Additionally, flowability, water absorption, microscopy, X-ray powder diffraction, and semi-adiabatic calorimetry results were analyzed in this study.

Treatment of diesel-contaminated soil using thermal water vapor arc plasma.

Soil pollution with petroleum-based fuels is a serious issue causing environmental problems. Recently, the use of plasma technologies for soil remediation has shown an interest and great potential. The remediation process can be performed in a fast timeframe without adding supplementary chemical reagents or without additional pre-treatment of the polluted soil. As a result, the use of plasma enables to obtain highly effective degradation of pollutants. Thus, in the present experimental research, diesel fuel removal from contaminated soil by utilizing thermal water vapor arc plasma was investigated. It was found that increased concentration of diesel fuel in the soil raised carbon and hydrogen concentrations in the soil. Moreover, soil surface morphology was modified by causing the formation of bigger agglomerates. It was also determined that after the plasma treatment process, soil grains became akin in size and structure to clean soil grains. A complete desorption of carbon, which came from diesel fuel to the soil, and a slight decomposition of organic carbon present in the soil were observed during the soil remediation process. Thermogravimetric analysis showed that regardless of the diesel fuel concentration in the soil, four stages of mass loss were observed: moisture loss, vaporization, and combustion of diesel fuel as well as reduction of volatiles and char in the soil. Producer gas analysis indicated that during soil remediation diesel fuel was mainly converted to synthesis gas, i.e., a mixture of H2, CO, and CO2. Moreover, the decomposition of diesel fuel and the formation of synthesis gas depended on the amount of pollutant in the soil. According to the obtained results, thermal water vapor arc plasma was able to completely remove diesel fuel from polluted soil in the form of synthesis gas with no significant influence on soil's properties.

Freshwater bryozoans of Lithuania (Bryozoa).

Nine species of freshwater bryozoans were recorded in Lithuania in a survey of 18 various types of freshwater bodies. Eight species were assigned to the Class Phylactolaemata and families Plumatellidae and Cristatellidae (Plumatella repens, Plumatella fungosa, Plumatella fruticosa, Plumatella casmiana, Plumatella emarginata, Plumatella geimermassardi, Hyalinella punctata and Cristatella mucedo). The ninth species, Paludicella articulata, represented the Class Gymnolaemata. Plumatella geimermassardi and P. casmiana were recorded for the first time in Lithuania. For the plumatellids, species identification was achieved partly by analysing statoblasts' morphological ultrastructures by scanning electron microscopy.