Detection of Crude Oil in Subsea Environments Using Organic Electrochemical Transistors.

Current methods for detecting pipeline oil leaks depend primarily on optical detection, which can be slow and have deployment limitations. An alternative non-optical approach for earlier and faster detection of oil leaks would enable a rapid response and reduce the environmental impact of oil leaks. Here, we demonstrate that organic electrochemical transistors (OECTs) can be used as non-optical sensors for crude oil detection in subsea environments. OECTs are thin film electronic devices that can be used for sensing in a variety of environments, but they have not yet been tested for crude oil detection in subsea environments. We fabricated OECTs with poly(3,4-ethylenedioxythiophene)-poly(styrenesulfonate) as the channel and showed that coating the channel with a polystyrene film results in an OECT with a large and measurable response to oil. Oil that comes in contact with the device will adsorb onto the polystyrene film and increases the impedance at the electrolyte interface. We performed electrochemical impedance spectroscopy measurements to quantify the impedance across the device and found an optimal thickness for the polystyrene coating for the detection of oil. Under optimal device characteristics, as little as 10 µg of oil adsorbed on the channel surface produced a statistically significant change in the source-drain current. The OECTs were operable in seawater for the detection of oil, and we demonstrated that the devices can be transferred to flexible substrates which can be easily implemented in vehicles, pipelines, or other surfaces. This work demonstrates a low-cost device for oil detection in subsea environments and provides a new application of OECT sensors for sensing.

Rapid identification of reproductive toxicants among environmental chemicals using an in vivo evaluation of gametogenesis in budding yeast Saccharomyces cerevisiae.

Infertility affects ∼12 % of couples, with environmental chemical exposure as a potential contributor. Of the chemicals that are actively manufactured, very few are assessed for reproductive health effects. Rodents are commonly used to evaluate reproductive effects, which is both costly and time consuming. Thus, there is a pressing need for rapid methods to test a broader range of chemicals. Here, we developed a strategy to evaluate large numbers of chemicals for reproductive toxicity via a yeast, S. cerevisiae high-throughput assay to assess gametogenesis as a potential new approach method (NAM). By simultaneously assessing chemicals for growth effects, we can distinguish if a chemical affects gametogenesis only, proliferative growth only or both. We identified a well-known mammalian reproductive toxicant, bisphenol A (BPA) and ranked 19 BPA analogs for reproductive harm. By testing mixtures of BPA and its analogs, we found that BPE and 17 ß-estradiol each together with BPA showed synergistic effects that worsened reproductive outcome. We examined an additional 179 environmental chemicals including phthalates, pesticides, quaternary ammonium compounds and per- and polyfluoroalkyl substances and found 57 with reproductive effects. Many of the chemicals were found to be strong reproductive toxicants that have yet to be tested in mammals. Chemicals having affect before meiosis I division vs. meiosis II division were identified for 16 gametogenesis-specific chemicals. Finally, we demonstrate that in general yeast reproductive toxicity correlates well with published reproductive toxicity in mammals illustrating the promise of this NAM to quickly assess chemicals to prioritize the evaluation for human reproductive harm.

Creation of a point-of-care therapeutics sensor using protein engineering, electrochemical sensing and electronic integration.

Point-of-care sensors, which are low-cost and user-friendly, play a crucial role in precision medicine by providing quick results for individuals. Here, we transform the conventional glucometer into a 4-hydroxytamoxifen therapeutic biosensor in which 4-hydroxytamoxifen modulates the electrical signal generated by glucose oxidation. To encode the 4-hydroxytamoxifen signal within glucose oxidation, we introduce the ligand-binding domain of estrogen receptor-alpha into pyrroloquinoline quinone-dependent glucose dehydrogenase by constructing and screening a comprehensive protein insertion library. In addition to obtaining 4-hydroxytamoxifen regulatable engineered proteins, these results unveil the significance of both secondary and quaternary protein structures in propagation of conformational signals. By constructing an effective bioelectrochemical interface, we detect 4-hydroxytamoxifen in human blood samples as changes in the electrical signal and use this to develop an electrochemical algorithm to decode the 4-hydroxytamoxifen signal from glucose. To meet the miniaturization and signal amplification requirements for point-of-care use, we harness power from glucose oxidation to create a self-powered sensor. We also amplify the 4-hydroxytamoxifen signal using an organic electrochemical transistor, resulting in milliampere-level signals. Our work demonstrates a broad interdisciplinary approach to create a biosensor that capitalizes on recent innovations in protein engineering, electrochemical sensing, and electrical engineering.

Solutions Are the Problem: Ordered Two-Dimensional Covalent Organic Framework Films by Chemical Vapor Deposition.

Covalent organic frameworks (COFs) are a promising class of crystalline polymer networks that are useful due to their high porosity, versatile functionality, and tunable architecture. Conventional solution-based methods of producing COFs are marred by slow reactions that produce powders that are difficult to process into adaptable form factors for functional applications, and there is a need for facile and fast synthesis techniques for making crystalline and ordered covalent organic framework (COF) thin films. In this work, we report a chemical vapor deposition (CVD) approach utilizing co-evaporation of two monomers onto a heated substrate to produce highly crystalline, defect-free COF films and coatings with hydrazone, imine, and ketoenamine COF linkages. This all-in-one synthesis technique produces highly crystalline, 40 nm-1 µm-thick COF films on Si/SiO2 substrates in less than 30 min. Crystallinity and alignment were proven by using a combination of grazing-incidence wide-angle X-ray scattering (GIWAXS) and transmission electron microscopy (TEM), and successful conversion of the monomers to produce the target COF was supported by Raman spectroscopy, X-ray photoelectron spectroscopy (XPS), and UV-vis measurements. Additionally, we used atomic force microscopy (AFM) to investigate the growth mechanisms of these films, showing the coalescence of triangular crystallites into a smooth film. To show the wide applicability and scope of the CVD process, we also prepared crystalline ordered COF films with imine and ketoenamine linkages. These films show potential as high-quality size exclusion membranes, catalytic platforms, and organic transistors.

Synthesis and Additive Manufacturing of Hydrazone-Linked Covalent Organic Framework Aerogels.

Covalent Organic Frameworks (COFs) are crystalline, porous organic materials. Recent studies have demonstrated novel processing strategies for COFs to form adaptable architectures, but these have focused primarily on imine-linked COFs. This work presents a new synthesis and processing route to produce crystalline hydrazone-linked COF gels and aerogels with hierarchical porosity. The method was implemented to produce a series of hydrazone-linked COFs with different alkyl side-chain substituents, achieving control of the hydrophilicity of the final aerogel. Variation in the length of the alkyl substituents yielded materials with controllable form factors that can preferentially adsorb water or nonpolar organic solvents. Additionally, a method for additive manufacturing of hydrazone-linked COFs using hydroxymethylcellulose as a sacrificial additive is presented. This work demonstrates an effective and simple approach to the fabrication of hydrazone COF aerogels and additive manufacturing to produce hydrazone COFs of desired shape.

Mixed Ionic-Electronic Conduction Increases the Rate Capability of Polynaphthalenediimide for Energy Storage.

Conjugated polymers offer a number of unique and useful properties for use as battery electrodes, and recent work has reported that conjugated polymers can exhibit excellent rate performance due to electron transport along the polymer backbone. However, the rate performance depends on both ion and electron conduction, and strategies for increasing the intrinsic ionic conductivities of conjugated polymer electrodes are lacking. Here, we investigate a series of conjugated polynapthalene dicarboximide (PNDI) polymers containing oligo(ethylene glycol) (EG) side chains that enhance ion transport. We produced PNDI polymers with varying contents of alkylated and glycolated side chains and investigated the impact on rate performance, specific capacity, cycling stability, and electrochemical properties through a series of charge-discharge, electrochemical impedance spectroscopy, and cyclic voltammetry measurements. We find that the incorporation of glycolated side chains results in electrode materials with exceptional rate performance (up to 500C, 14.4 s per cycle) in thick (up to 20 µm), high-polymer-content (up to 80 wt %) electrodes. Incorporation of EG side chains enhances both ionic and electronic conductivities, and we found that PNDI polymers with at least 90% of NDI units containing EG side chains functioned as carbon-free polymer electrodes. This work demonstrates that polymers with mixed ionic and electronic conduction are excellent candidates for battery electrodes with good cycling stability and capable of ultra-fast rate performance.

Three-dimensional covalent organic frameworks with pto and mhq-z topologies based on Tri- and tetratopic linkers.

Three-dimensional (3D) covalent organic frameworks (COFs) possess higher surface areas, more abundant pore channels, and lower density compared to their two-dimensional counterparts which makes the development of 3D COFs interesting from a fundamental and practical point of view. However, the construction of highly crystalline 3D COF remains challenging. At the same time, the choice of topologies in 3D COFs is limited by the crystallization problem, the lack of availability of suitable building blocks with appropriate reactivity and symmetries, and the difficulties in crystalline structure determination. Herein, we report two highly crystalline 3D COFs with pto and mhq-z topologies designed by rationally selecting rectangular-planar and trigonal-planar building blocks with appropriate conformational strains. The pto 3D COFs show a large pore size of 46 Å with an extremely low calculated density. The mhq-z net topology is solely constructed from totally face-enclosed organic polyhedra displaying a precise uniform micropore size of 1.0 nm. The 3D COFs show a high CO2 adsorption capacity at room temperature and can potentially serve as promising carbon capture adsorbents. This work expands the choice of accessible 3D COF topologies, enriching the structural versatility of COFs.

Tailoring the Wettability and Substrate Adherence of Thin Polymer Films with Surface-Segregating Bottlebrush Copolymer Additives.

We developed "reactive" bottlebrush polymers based on styrene (S) and t-butyl acrylate (tBA) as additives for polystyrene (PS) coatings. The bottlebrush polymers spontaneously bloom to both the air and substrate interfaces during solution casting. While neat PS films are hydrophobic and poorly adhere to the native oxide on clean silicon wafers, the hydrophilicity and substrate adherence of bottlebrush-incorporating PS films can be tailored through the thermally activated deprotection of tBA to produce acrylic acid (AA) and acrylic anhydride (AH). A critical design parameter is the manner by which tBA is incorporated into the bottlebrush: When the bottlebrush side chains are copolymers of S and tBA, the extent of deprotection is extremely low, even after prolonged thermal annealing at elevated temperature. However, when the bottlebrush contains a mixture of poly(t-butyl acrylate) (PtBA) and PS side chains, nearly all tBA is converted to AA and AH. Consequently, using the "mixed-chain" bottlebrush design with thermal processing and appropriate conditioning, the water contact angle is reduced from over 90° on unmodified PS down to 75° on bottlebrush-incorporating PS films, and the substrate adherence is improved in proportion to the extent of tBA deprotection.

Precise Cation Separations with Composite Cation-Exchange Membranes: Role of Base Layer Properties.

Separation of specific ions from water could enable recovery and reuse of essential metals and nutrients, but established membrane technologies lack the high-precision selectivity needed to facilitate a circular resource economy. In this work, we investigate whether the cation/cation selectivity of a composite cation-exchange membrane (CEM), or a thin polymer selective layer on top of a CEM, may be limited by the mass transfer resistance of the underlying CEM. In our analysis, we utilize a layer-by-layer technique to modify CEMs with a thin polymer selective layer (∼50 nm) that has previously shown high selectivity toward copper over similarly sized metals. While these composite membranes have a CuCl2/MgCl2 selectivity up to 33 times larger than unmodified CEMs in diffusion dialysis, our estimates suggest that eliminating resistance from the underlying CEM could further increase selectivity twofold. In contrast, the CEM base layer has a smaller effect on the selectivity of these composite membranes in electrodialysis, although these effects could become more pronounced for ultrathin or highly conductive selective layers. Our results highlight that base layer resistance prevents selectivity factors from being comparable across diffusion dialysis and electrodialysis, and CEMs with low resistance are necessary for providing highly precise separations with composite CEMs.

Enabling Solution Processable COFs through Suppression of Precipitation during Solvothermal Synthesis.

Covalent organic frameworks (COFs) are crystalline, nanoporous materials of interest for various applications, but current COF synthetic routes lead to insoluble aggregates which precludes processing for practical implementation. Here, we report a COF synthesis method that produces a stable, homogeneous suspension of crystalline COF nanoparticles that enables the preparation of COF monoliths, membranes, and films using conventional solution-processing techniques. Our approach involves the use of a polar solvent, diacid catalyst, and slow reagent mixing procedure at elevated temperatures which altogether enable access to crystalline COF nanoparticle suspension that does not aggregate or precipitate when kept at elevated temperatures. On cooling, the suspension undergoes a thermoreversible gelation transition to produce crystalline and highly porous COF materials. We further show that the modified synthesis approach is compatible with various COF chemistries, including both large- and small-pore imine COFs, hydrazone-linked COFs, and COFs with rhombic and hexagonal topologies, and in each case, we demonstrate that the final product has excellent crystallinity and porosity. The final materials contain both micro- and macropores, and the total porosity can be tuned through variation of sample annealing. Dynamic light scattering measurements reveal the presence of COF nanoparticles that grow with time at room temperature, transitioning from a homogeneous suspension to a gel. Finally, we prepare imine COF membranes and measure their rejection of polyethylene glycol (PEG) polymers and oligomers, and these measurements exhibit size-dependent rejection and adsorption of PEG solutes. This work demonstrates a versatile processing strategy to create crystalline and porous COF materials using solution-processing techniques and will greatly advance the development of COFs for various applications.

Protein-imprinted particles for coronavirus capture from solution.

Molecular imprinting is a promising strategy to selectively adsorb viruses, but it requires discerning and validating epitopes that serve as effective imprinting templates. In this work, glycoprotein-imprinted particles were synthesized for coronavirus capture. Adsorption was maximized at pH 6 (the glycoprotein isoelectric point) where the glycoprotein-imprinted particles outperformed non-imprinted particles, adsorbing 4.96 × 106  ± 3.33 × 103 versus 3.54 × 106  ± 1.39 × 106 median tissue culture infectious dose/mg of the target coronavirus, human coronavirus - organ culture 43, within the first 30 min (p = 0.012). During competitive adsorption, with pH adjustment (pH 6), the glycoprotein-imprinted particles adsorbed more target virus than non-target coronavirus (human coronavirus - Netherland 63) with 2.34 versus 1.94 log removal in 90 min (p < 0.01). In contrast, the non-imprinted particles showed no significant difference in target versus non-target virus removal. Electrostatic potential calculation shows that the human coronavirus - organ culture 43 glycoprotein has positively charged pockets at pH 6, which may facilitate adsorption at lower pH values. Therefore, tuning the target virus glycoprotein charge via pH adjustment enhanced adsorption by minimizing repulsive electrostatic interactions with the particles. Overall, these results highlight the effective use of glycoprotein-imprinted particles for coronavirus capture and discern the merits and limitations of glycoprotein imprinting for the capture of enveloped viruses.

Understanding fragility and engineering activation stability in two-dimensional covalent organic frameworks.

The sensitivity of covalent organic frameworks (COFs) to pore collapse during activation processes is generally termed activation stability, and activation stability is important for achieving and maintaining COF crystallinity and porosity which are relevant to a variety of applications. However, current understanding of COF stability during activation is insufficient, and prior studies have focused primarily on thermal stability or on the activation stability of other porous materials, such as metal-organic frameworks (MOFs). In this work, we demonstrate and implement a versatile experimental approach to quantify activation stability of COFs and use this to establish a number of relationships between their pore size, the type of pore substituents, pore architecture, and structural robustness. Additionally, density functional theory calculations reveal the impact on both inter-and intra-layer interactions, which govern activation stability, and we demonstrate that activation stability can be systematically tuned using a multivariate synthesis approach involving mixtures of functionalized and unfunctionalized COF building blocks. Our findings provide novel fundamental insights into the activation stability of COFs and offer guidance for the design of more robust COFs.

Understanding the effect of liquid crystal content on the phase behavior and mechanical properties of liquid crystal elastomers.

Liquid crystal elastomers are stimuli-responsive, shape-shifting materials. They typically require high temperatures for actuation which prohibits their use in many applications, such as biomedical devices. In this work, we demonstrate a simple and general approach to tune the order-to-disorder transition temperature (TODT) or nematic-to-isotropic transition temperature (TNI) of LCEs through variation of the overall liquid crystal mass content. We demonstrate reduction of the TNI in nematic LCEs through the incorporation of non-mesogenic linkers or the addition of lithium salts, and show that the TNI varies linearly with liquid crystal mass content over a broad range, approximately 50 °C. We also analyze data from prior reports that include three different mesogens, different network linking chemistries, and different alignment strategies, and show that the linear trend in TODT with liquid crystal mass content also holds for these systems. Finally, we demonstrate a simple approach to quantifying the maximum actuation strain through measurement of the soft elastic plateau and demonstrate applications of nematic LCEs with low TODTs, including the first body-responsive LCE that curls around a human finger due to body heat, and a fluidic channel that directionally pumps liquid when heated.

Eggshell membrane derived nitrogen rich porous carbon for selective electrosorption of nitrate from water.

Nitrate (NO3-) is a ubiquitous contaminant in water and wastewater. Conventional treatment processes such as adsorption and membrane separation suffer from low selectivity for NO3- removal, causing high energy consumption and adsorbents usage. In this study, we demonstrate selective removal of NO3- in an electrosorption process by a thin, porous carbonized eggshell membrane (CESM) derived from eggshell bio-waste. The CESM possesses an interconnected hierarchical pore structure with pore size ranging from a few nanometers to tens of micrometers. When utilized as the anode in an electrosorption process, the CESM exhibited strong selectivity for NO3- over Cl-, SO42-, and H2PO4-. Adsorption of NO3- by the CESM reached 2.4 × 10-3 mmol/m2, almost two orders of magnitude higher than that by activated carbon (AC). More importantly, the CESM achieved NO3-/Cl- selectivity of 7.79 at an applied voltage of 1.2 V, the highest NO3-/Cl- selectivity reported to date. The high selectivity led to a five-fold reduction in energy consumption for NO3- removal compared to electrosorption using conventional AC electrodes. Density function theory calculation suggests that the high NO3- selectivity of CESM is attributed to its rich nitrogen-containing functional groups, which possess higher binding energy with NO3- compared to Cl-, SO42-, and H2PO4-. These results suggest that nitrogen-rich biomaterials are good precursors for NO3- selective electrodes; similar chemistry can also be used in other materials to achieve NO3- selectivity.

Designing polymeric membranes with coordination chemistry for high-precision ion separations.

State-of-the-art polymeric membranes are unable to perform the high-precision ion separations needed for technologies essential to a circular economy and clean energy future. Coordinative interactions are a mechanism to increase sorption of a target species into a membrane, but the effects of these interactions on membrane permeability and selectivity are poorly understood. We use a multilayered polymer membrane to assess how ion-membrane binding energies affect membrane permeability of similarly sized cations: Cu2+, Ni2+, Zn2+, Co2+, and Mg2+. We report that metals with higher binding energy to iminodiacetate groups of the polymer more selectively permeate through the membrane in multisalt solutions than single-salt solutions. In contrast, weaker binding species are precluded from diffusing into the polymer membrane, which leads to passage proportional to binding energy and independent of membrane thickness. Our findings demonstrate that selectivity of polymeric membranes can markedly increase by tailoring ion-membrane binding energy and minimizing membrane thickness.

3D Covalent Organic Frameworks with Interpenetrated pcb Topology Based on 8-Connected Cubic Nodes.

The connectivity of building units for 3D covalent organic frameworks (COFs) has long been primarily 4 and 6, which have severely curtailed the structural diversity of 3D COFs. Here we demonstrate the successful design and synthesis of a porphyrin based, 8-connected building block with cubic configuration, which could be further reticulated into an unprecedented interpenetrated pcb topology by imine condensation with linear amine monomers. This study presents the first case of high-connectivity building units bearing 8-connected cubic nodes, thus greatly enriching the topological possibilities of 3D COFs.

Solution-Deposited and Patternable Conductive Polymer Thin-Film Electrodes for Microbial Bioelectronics.

Microbial bioelectronic devices integrate naturally occurring or synthetically engineered electroactive microbes with microelectronics. These devices have a broad range of potential applications, but engineering the biotic-abiotic interface for biocompatibility, adhesion, electron transfer, and maximum surface area remains a challenge. Prior approaches to interface modification lack simple processability, the ability to pattern the materials, and/or a significant enhancement in currents. Here, a novel conductive polymer coating that significantly enhances current densities relative to unmodified electrodes in microbial bioelectronics is reported. The coating is based on a blend of poly(3,4-ethylenedioxythiophene)-poly(styrenesulfonate) (PEDOT:PSS) crosslinked with poly(2-hydroxyethylacrylate) (PHEA) along with a thin polydopamine (PDA) layer for adhesion to an underlying indium tin oxide (ITO) electrode. When used as an interface layer with the current-producing bacterium Shewanella oneidensis MR-1, this material produces a 178-fold increase in the current density compared to unmodified electrodes, a current gain that is higher than previously reported thin-film 2D coatings and 3D conductive polymer coatings. The chemistry, morphology, and electronic properties of the coatings are characterized and the implementation of these coated electrodes for use in microbial fuel cells, multiplexed bioelectronic devices, and organic electrochemical transistor based microbial sensors are demonstrated. It is envisioned that this simple coating will advance the development of microbial bioelectronic devices.

Corrosion Resistance of Sulfur-Selenium Alloy Coatings.

Despite decades of research, metallic corrosion remains a long-standing challenge in many engineering applications. Specifically, designing a material that can resist corrosion both in abiotic as well as biotic environments remains elusive. Here a lightweight sulfur-selenium (S-Se) alloy is designed with high stiffness and ductility that can serve as an excellent corrosion-resistant coating with protection efficiency of ≈99.9% for steel in a wide range of diverse environments. S-Se coated mild steel shows a corrosion rate that is 6-7 orders of magnitude lower than bare metal in abiotic (simulated seawater and sodium sulfate solution) and biotic (sulfate-reducing bacterial medium) environments. The coating is strongly adhesive, mechanically robust, and demonstrates excellent damage/deformation recovery properties, which provide the added advantage of significantly reducing the probability of a defect being generated and sustained in the coating, thus improving its longevity. The high corrosion resistance of the alloy is attributed in diverse environments to its semicrystalline, nonporous, antimicrobial, and viscoelastic nature with superior mechanical performance, enabling it to successfully block a variety of diffusing species.

Understanding interfacial segregation in polymer blend films with random and mixed side chain bottlebrush copolymer additives.

Bottlebrush polymers are complex macromolecules with tunable physical properties dependent on the chemistry and architecture of both the side chains and the backbone. Prior work has demonstrated that bottlebrush polymer additives can be used to control the interfacial properties of blends with linear polymers but has not specifically addressed the effects of bottlebrush side chain microstructures. Here, using a combination of experiments and self-consistent field theory (SCFT) simulations, we investigated the effects of side chain microstructures by comparing the segregation of bottlebrush additives having random copolymer side chains with bottlebrush additives having a mixture of two different homopolymer side chain chemistries. Specifically, we synthesized bottlebrush polymers with either poly(styrene-ran-methyl methacrylate) side chains or with a mixture of polystyrene (PS) and poly(methyl methacrylate) (PMMA) side chains. The bottlebrush additives were matched in terms of PS and PMMA compositions, and they were blended with linear PS or PMMA chains that ranged in length from shorter to longer than the bottlebrush side chains. Experiments revealed similar behaviors of the two types of bottlebrushes, with a slight preference for mixed side-chain bottlebrushes at the film surface. SCFT simulations were qualitatively consistent with experimental observations, predicting only slight differences in the segregation of bottlebrush additives driven by side chain microstructures. Specifically, these slight differences were driven by the chemistries of the bottlebrush polymer joints and side chain end-groups, which were entropically repelled and attracted to interfaces, respectively. Using SCFT, we also demonstrated that the interfacial behaviors were dominated by entropic effects with high molecular weight linear polymers, leading to enrichment of bottlebrush near interfaces. Surprisingly, the SCFT simulations showed that the chemistry of the joints connecting the bottlebrush backbones and side chains played a more significant role compared with the side chain end groups in affecting differences in surface excess of bottlebrushes with random and mixed side chains. This work provides new insights into the effects of side chain microstructure on segregation of bottlebrush polymer additives.

Membrane Materials for Selective Ion Separations at the Water-Energy Nexus.

Synthetic polymer membranes are enabling components in key technologies at the water-energy nexus, including desalination and energy conversion, because of their high water/salt selectivity or ionic conductivity. However, many applications at the water-energy nexus require ion selectivity, or separation of specific ionic species from other similar species. Here, the ion selectivity of conventional polymeric membrane materials is assessed and recent progress in enhancing selective transport via tailored free volume elements and ion-membrane interactions is described. In view of the limitations of polymeric membranes, three material classes-porous crystalline materials, 2D materials, and discrete biomimetic channels-are highlighted as possible candidates for ion-selective membranes owing to their molecular-level control over physical and chemical properties. Lastly, research directions and critical challenges for developing bioinspired membranes with molecular recognition are provided.