Fluorescent Conversion Agent Embedded in Zinc Oxide as an Electron-Transporting Layer for High-Performance Non-Fullerene Organic Solar Cells with Improved Photostability.

Zinc oxide (ZnO) is widely used as an electron transporting layer (ETL) for organic solar cells (OSCs). Here, a low-cost commercial water/alcohol-soluble fluorescent conversion agent, sodium 2,2'-([1,1'-biphenyl]-4,4'-diyldivinylene)-bis(benzenesulfonate) (CBS), is incorporated into ZnO to develop a novel organic-inorganic hybrid ETL for high-performance OSCs. The photoinduced charge transfer from CBS to ZnO significantly improves the charge transport properties of ZnO, resulting in faster electron extraction and reduced charge recombination in OSC devices with ZnO:CBS ETLs. ZnO:CBS-based devices exhibit higher power conversion efficiencies (PCEs) than their pure ZnO-based counterparts, especially in devices with a thicker ETL, which is more suitable for roll-to-roll and large-area module processing. Furthermore, the strong ultraviolet-light absorption capability of CBS inhibits the photodegradation of the active layer, improving the photostability of ZnO:CBS based OSC devices. Therefore, this work provides a simple and effective strategy for realizing high-performance OSCs with high PCE and good photostability, which can further facilitate the commercialization of OSCs.

Surpassing 13% Efficiency for Polythiophene Organic Solar Cells Processed from Nonhalogenated Solvent.

Benefiting from low cost and simple synthesis, polythiophene (PT) derivatives are one of the most popular donor materials for organic solar cells (OSCs). However, polythiophene-based OSCs still suffer from inferior power conversion efficiency (PCE) than those based on donor-acceptor (D-A)-type conjugated polymers. Herein, a fluorinated polythiophene derivative, namely P4T2F-HD, is introduced to modulate the miscibility and morphology of the bulk heterojunction (BHJ)-active layer, leading to a significant improvement of the OSC performance. The Flory-Huggins interaction parameters calculated from the surface energy and differential scanning calorimetry results suggest that P4T2F-HD shows moderate miscibility with the popular nonfullerene acceptor Y6-BO (2,2'-((2Z,2'Z)-((12,13-bis(2-butyloctyl)-3,9-diundecyl-12,13-dihydro-[1,2,5]thiadiazolo[3,4-e]thieno[2',3':4',5']thieno[2',3':4,5]pyrrolo[3,2-g]thieno[2',3':4,5]thieno[3,2-b]indole-2,10-diyl)bis(methanylylidene))bis(5,6-difluoro-3-oxo-2,3-dihydro-1H-indene-2,1-diylidene))dimalononitrile), while poly(3-hexylthiophene) (P3HT) is very miscible with Y6-BO. As a result, the P4T2F-HD case forms desired nanoscale phase separation in the BHJ film while the P3HT case forms a completely mixed BHJ film, as revealed by transmission electron microscopy (TEM) and grazing-incidence wide-angle X-ray scattering (GIWAXS). By optimizing the cathode interface and the morphology of the P4T2F-HD:Y6-BO films processed from nonhalogenated solvents, a new record PCE of 13.65% for polythiophene-based OSCs is demonstrated. This work highlights the importance of controlling D/A interactions for achieving desired morphology and also demonstrates a promising OSC system for potential cost-effective organic photovoltaics.

Delocalization of exciton and electron wavefunction in non-fullerene acceptor molecules enables efficient organic solar cells.

A major challenge for organic solar cell (OSC) research is how to minimize the tradeoff between voltage loss and charge generation. In early 2019, we reported a non-fullerene acceptor (named Y6) that can simultaneously achieve high external quantum efficiency and low voltage loss for OSC. Here, we use a combination of experimental and theoretical modeling to reveal the structure-property-performance relationships of this state-of-the-art OSC system. We find that the distinctive π-π molecular packing of Y6 not only exists in molecular single crystals but also in thin films. Importantly, such molecular packing leads to (i) the formation of delocalized and emissive excitons that enable small non-radiative voltage loss, and (ii) delocalization of electron wavefunctions at donor/acceptor interfaces that significantly reduces the Coulomb attraction between interfacial electron-hole pairs. These properties are critical in enabling highly efficient charge generation in OSC systems with negligible donor-acceptor energy offset.

High-Performance Ternary Organic Solar Cells with Controllable Morphology via Sequential Layer-by-Layer Deposition.

Ternary blending of light-harvesting materials has been proven to be a potential strategy to improve the efficiency of solution-processed organic solar cells (OSCs). However, the optimization of a ternary system is usually more complicated than that of a binary one as the morphology of conventional ternary blend films is very difficult to control, thus undermining the potential of ternary OSCs. Herein, we report a general strategy for better control of the morphology of ternary blend films composed of a polymer donor and two nonfullerene small-molecule acceptors for high-performance OSCs using the sequential layer-by-layer (LbL) deposition method. The resulting LbL films form a bicontinuous interpenetrating network structure with high crystallinity of both the donor and acceptor materials, showing efficient charge generation, transport, and collection properties. In addition, the power conversion efficiencies (PCEs) of the ternary LbL OSCs are less sensitive to the blending ratio of the third component acceptor, providing more room to optimize the device performance. As a result, optimal PCEs of over 11, 13, and 16% were achieved for the LbL OSCs composed of PffBT4T-2OD/IEICO-4F:FBR, PBDB-T-SF/IT-4F:FBR, and PM6/Y6:FBR, respectively. Our work provides useful and general guidelines for the development of more efficient ternary OSCs with better controlled morphology.

Interface-enhanced organic solar cells with extrapolated T80 lifetimes of over 20 years.

With recent advances in the power conversion efficiency (PCE) of organic solar cells (OSCs) based on novel donor and non-fullerene acceptor (NFAs), improving the stability of these systems has become the most important issue for their practical applications. Herein, an efficient and highly stable OSC, containing a novel polymer donor and a non-fullerene acceptor system, is reported. The OSC is based on an inverted device structure that utilizes a self-assembled fullerene monolayer (C60-SAM) as the cathode modification layer, and an efficient and highly stable OSC composes of a polymer donor of poly[4,8-bis(5-(2-ethylhexyl)thiophen-2-yl)benzo[1,2-b:4,5-b']dithiophene-alt-3-fluorothie-no[3,4-b]thiophene-2-carboxylate] (PTB7-Th) and a non-fullerene acceptor of (2,2'-((2Z,2'Z)-(((4,4,9,9-Tetrakis(4-hexylphenyl)-4,9-dihydro-sindaceno[1,2-b:5,6-b']dithiophene-2,7-diyl)bis(4-((2ethylhexyl)oxy)thiophene-5,2-diyl))bis(methanylylidene))bis(5,6-difluoro-3-oxo-2,3-dihydro-1H-indene -2,1-diylidene))dimalononitrile) (IEICO-4F) is presented, showing a PCE of 10%. It further achieves an extrapolated T80 lifetime (the time required to reach 80% of initial performance) of 34,000 h, operating under one sun illumination equivalent. Based on an estimated solar irradiance of 1500 kWh/(m2 year) for China, a potential lifetime of 22 years is inferred for the OSC. Further investigation reveals that the reported C60-SAM modification stabilizes the OSC active layer morphology by lowering the surface energy of the underlying ZnO electron transport layer and suppressing trap-assisted recombination, thereby improving photostability. The results of this work establish important guidelines for the development of non-fullerene based OSCs with enhanced stability and pave the way for the commercialization of OSC technology.

Decomposition of Organometal Halide Perovskite Films on Zinc Oxide Nanoparticles.

Solution processed zinc oxide (ZnO) nanoparticles (NPs) with excellent electron transport properties and a low-temperature process is a viable candidate to replace titanium dioxide (TiO2) as electron transport layer to develop high-efficiency perovskite solar cells on flexible substrates. However, the number of reported high-performance perovskite solar cells using ZnO-NPs is still limited. Here we report a detailed investigation on the chemistry and crystal growth of CH3NH3PbI3 perovskite on ZnO-NP thin films. We find that the perovskite films would severely decompose into PbI2 upon thermal annealing on the bare ZnO-NP surface. X-ray photoelectron spectroscopy (XPS) results show that the hydroxide groups on the ZnO-NP surface accelerate the decomposition of the perovskite films. To reduce the decomposition, we introduce a buffer layer in between the ZnO-NPs and perovskite layers. We find that a commonly used buffer layer with small molecule [6,6]-phenyl-C61-butyric acid methyl ester (PC61BM) can slow down but cannot completely avoid the decomposition. On the other hand, a polymeric buffer layer using poly(ethylenimine) (PEI) can effectively separate the ZnO-NPs and perovskite, which allows larger crystal formation with thermal annealing. The power conversion efficiencies of perovskite photovoltaic cells are significantly increased from 6.4% to 10.2% by replacing PC61BM with PEI as the buffer layer.