Design of a Humidity Sensor for a PPE Kit Using a Flexible Paper Substrate.

The present work reports the rapid sweat detection inside a PPE kit using a flexible humidity sensor based on hydrothermally synthesized ZnO (zinc oxide) nanoflowers (ZNFs). Physical characterization of ZNFs was done using scanning electron microscopy (SEM), X-ray diffraction (XRD), Fourier transmission infrared spectroscopy (FTIR), UV-visible, particle size analysis, Raman analysis, and X-ray photoelectron spectroscopy (XPS) analysis, and the hydrophilicity was investigated by using contact angle measurement. Fabrication of a flexible sensor was done by deposition on the paper substrate using the spin coating technique. It exhibited high sensitivity and low response and recovery times in the humidity range 10-95%RH. The sensor demonstrated the highest sensitivity of 296.70 nF/%RH within the humidity range 55-95%RH, and the rapid response and recovery times were also calculated and found as 5.10/1.70 s, respectively. The selectivity of the proposed sensor was also analyzed, and it is highly sensitive to humidity. The humidity sensing characteristics were theoretically witnessed in terms of the highest occupied molecular orbital (HOMO) and lowest unoccupied molecular orbital (LUMO) and electronic properties of sensing materials in ambient and humid conditions. These theoretical results are evidence of the interaction of ZnO with humidity. Overall, the present study provides a scope of architecture-enabled paper-based humidity sensors for the detection of sweat levels inside PPE kits for health workers.

Exploring the weak visible-near-infrared and NO2detection capabilities of PbS/Sb2O5heterostructures with DFT interpretations.

The need for photosensors and gas sensors arises from their pivotal roles in various technological applications, ensuring enhanced efficiency, safety, and functionality in diverse fields. In this paper, interlinked PbS/Sb2O5thin film has been synthesized by a magnetron sputtering method. We control the temperature to form the nanocomposite by using their different nucleation temperature during the sulfonation process. A nanostructured PbS/Sb2O5with cross-linked morphology was synthesized by using this fast and efficient method. This method has also been used to grow a uniform thin film of nanocomposite. The photo-sensing and gas-sensing properties related to the PbS/Sb2O5compared with those of other nanomaterials have also been investigated. The experimental and theoretical calculations reveal that the PbS/Sb2O5exhibits extraordinarily superior photo-sensing and gas-sensing properties in terms of providing a pathway for electron transport to the electrode. The attractive highly sensitive photo and gas sensing properties of PbS/Sb2O5make them applicable for many different kinds of applications. The responsivity and detectivity of PbS/Sb2O5are 0.28 S/mWcm-2and 1.68 × 1011Jones respectively. The sensor response towards NO2gas was found to be 0.98 at 10 ppb with an limit of detection (LOD) of 0.083 ppb. The PbS/Sb2O5exhibits high selectivity towards the NO2gas. Density functional theory (DFT) and time-dependent density functional theory (TD-DFT) were used to analyze the geometries, electronic structure, and electronic absorption spectra of a light sensor fabricated by PbS/Sb2O5. The results are very analogous to the experimental results. Both photosensors and gas sensors are indispensable tools that contribute significantly to the evolution of technology and the improvement of various aspects of modern life.

An investigation into the hybrid architecture of Mn-Co nanoferrites incorporated into a polyaniline matrix for photoresponse studies.

In this study, an enhanced photoresponse was observed in the Mn-Co Nanoferrites (MCFs)-Polyaniline (PANI) nanohybrid architecture due to the formation of interface between PANI and MCFs, which provided a conduction pathway for the movement of charge carriers, and these interfaces were observed in a high-resolution transmission electron micrograph (HR-TEM). X-ray photoelectron spectroscopy (XPS) suggests that the carbon (C 1s) of the MCF-PANI nanohybrid shows peaks at 287.80 eV for CO, 286.17 eV for C-O, 285.24 eV for C-N, 284.50 eV for the sp3 hybridized carbon (C-C/C-H) and 283.84 eV for the sp2 hybridized carbon (CC). Current-voltage (I-V) curves reveal an ohmic nature of the MCF-PANI nanohybrid photodetector device. The photoresponse measurements were analyzed using the trap depth concept, demonstrating that the conductive polymer increases the photoconduction mechanism efficiency of MCFs. The constructed photodetector device exhibits a high photoresponsivity of 22.69 A W-1, a remarkable detectivity of 1.36 × 1012 cm Hz1/2 W-1 and a fast rise/decay time of 0.7/0.8 s. The excellent performance of the as-fabricated photodetector device could be explained by the intimate interaction between MCFs and PANI at their interface.

CuMoO4 nanorods-based acetone chemiresistor-enabled non-invasive breathomic-diagnosis of human diabetes and environmental monitoring.

A nano-enabled low-trace monitoring system for acetone has the potential to revolutionize breath omics-based non-invasive diagnosis of human diabetes and environmental monitoring technologies. This unprecedented study presents the state-of-the-art facile and economic template-assisted hydrothermal route to fabricate novel CuMoO4 nanorods for room temperature breath and airborne acetone detection. Physicochemical attribute analysis reveals the formation of crystalline CuMoO4 nanorods with diameters ranging from 90 to 150 nm, and an optical band gap of approximately 3.87 eV. CuMoO4 nanorods-based chemiresistor demonstrates excellent acetone monitoring performance, with a sensitivity of approximately 33.85 at a concentration of 125 ppm. Acetone detection is rapid, with a response time of 23 s and fast recovery within 31 s. Furthermore, the chemiresistor exhibits long-term stability and selectivity towards acetone, compared to other interfering volatile organic compounds (VOCs) commonly found in human breath such as ethanol, propanol, formaldehyde, humidity, and ammonia. The linear detection range of acetone from 25 to 125 ppm achieved by the fabricated sensor is well-suited for human breath-based diagnosis of diabetes. This work represents a significant advancement in the field, as it offers a promising alternative to time-consuming and costly invasive biomedical diagnostics, with the potential for application in cleanroom facilities for indoor contamination monitoring. The utilization of CuMoO4 nanorods as sensing nanoplatform opens new possibilities for the development of nano-enabled, low-trace acetone monitoring technologies for non-invasive diabetes diagnosis and environmental sensing applications.

Facile synthesized zinc oxide nanorod film humidity sensor based on variation in optical transmissivity.

Variation in the transmitted light intensity from metal oxide thin films with moisture content provides a great opportunity to use them for humidity sensing. Herein, we have developed a novel and simple humidity sensor based on ZnO nanorod (ZNR) thin films which work as transmission-based sensing elements in an in-house fabricated sensing setup. The ZNR sensing element shows excellent linear sensing performance in the relative humidity (RH) range 10-90% and does not show any hysteresis. A maximum change in optical power of ∼95 µW is observed with the change in RH in the range 10-90%, for the sample with the smallest crystallite size (ZNR1) and highest pore diameter of the ZNR film. Also, a maximum sensitivity of 1.104 µW/% RH is observed for the ZNR1 sample which drops to 0.604 µW/% RH for the highest crystallite size sample (ZNR4). The presence of oxygen vacancies and the micro-porous nature of the film allow the absorption of water vapour on the film which deflects light at different angles that vary with the moisture content. The experimental results suggest that the ZNR film with a smaller crystallite size and larger pore diameter is more sensitive for humidity measurements. Further, an improved sensing performance is perceived in ZNRs because of the larger surface area of the nanorods. The ZNR based sensing elements do not suffer from ageing effects and exhibit high repeatability (88.74%). Further, the humidity sensor has a response time of 62 seconds and recovery time of 100 seconds which can be considered as a fairly quick response.

Earth-abundant and environmentally benign Ni-Zn iron oxide intercalated in a polyaniline based nanohybrid as an ultrafast photodetector.

Nickel-zinc iron oxide (NZF) was introduced into a polyaniline (PANI) matrix by an in situ chemical oxidation polymerization approach. The surface composition and chemical states were investigated by X-ray photoelectron spectroscopy (XPS), which revealed an Fe 2p spectrum with the two peak positions of Fe 2p3/2 and Fe 2p1/2 at 711.00 and 724.48 eV, respectively. Deconvolution of the Fe 2p3/2 peak revealed two components with binding energies of 713.98 and 718.16 eV, corresponding to the presence of Fe cations in the octahedral and tetrahedral sites. Additionally, the Rietveld refinement of NZF showed a cubic system with the Fd3m space group. High-resolution transmission electron microscopy (HRTEM) analysis showed that the NZF material strongly interacts with polyaniline, while the selected area electron diffraction (SAED) pattern perfectly matched with the XRD data. Lognormal distribution was used to determine the particle size, which was found to be in the range of 1-100 nm. A flexible photodetector device utilizing the NZF-PANI nanohybrid was fabricated on an environmentally friendly, biodegradable cellulose paper substrate and the device exhibited excellent performance, i.e., a responsivity of 0.069 A W-1 and detectivity of 7.258 × 1010 Jones at a very low voltage of 0.1 V. The non-stretched device showed a responsivity of 24.980 A W-1 at 5 V, whereas at 2 cm-1 bending curvature, the device showed a responsivity of 20.175 A W-1, which was much higher than the responsivity of a commercial photodetector (<0.5 A W-1).

The rapid response and high sensitivity of a ruthenium-doped copper ferrite thin film (Ru-CuFe2O4) sensor.

A sensor displaying a rapid response and high sensitivity was developed by following a simple route. Ionic defects in this sensor were explored using X-ray diffraction analysis. In general, such defects arise from a mismatch of ionic radii, which actually improves the sensing performance. SEM and TEM images of the currently produced particles demonstrated negligible agglomeration, which greatly enhanced the flow of water molecules through the particles. The current sensor showed a rapid response to changes in humidity. Its sensing performance was classified into three different ranges of humidity. Of these humidity ranges, the sensor showed the highest sensitivity (8.84 MΩ per %RH) at low relative humidity (10-20% RH). Furthermore, the sensitivity fall off as the RH was increased from 20 to 99%. The sensor showed a rapid response time of 20 s. Also, the sensor showed 92.98% reproducibility and few effects of aging.

Nanostructured cobalt antimonate: a fast responsive and highly stable sensing material for liquefied petroleum gas detection at room temperature.

Herein, cobalt antimonate (CoSb2O6) nanospheres were fabricated via the sol-gel spin-coating process and employed as a functional liquefied petroleum gas (LPG) sensor at room temperature (25 °C). The microstructure of the fabricated CoSb2O6 thin films (thickness ∼ 250 nm) was analyzed via scanning electron microscopy, which revealed the growth of nanospheres having an average diameter of ∼45 nm. The XRD analysis demonstrated the crystalline nature of CoSb2O6 with a crystallite size of ∼27 nm. Finally, the fabricated thin films were investigated as sensors for LPG and carbon dioxide (CO2) at room temperature (25 °C) and 55% R.H. (relative humidity) with different concentrations in the range of 1000-5000 ppm. The sensing results demonstrated greater variations in the electrical properties of films for the incoming LPG than that of the CO2 gas adsorption. Furthermore, to ensure the long-term stability of fabricated sensors, they were tested periodically at 10 days interval, spanning a total duration of 60 days. In summary, our fabricated LPG sensor displayed high sensitivity (1.96), repeatability, quick response time (21 s) and high long-term stability (99%). Therefore, CoSb2O6 nanospheres can be functionalized as a potential LPG-sensitive material characterized by high sensitivity, reliability and stability at room temperature.

Traveling-waves of metal-containing monomer polymerization without diffusion and heat-transfer.

The new approach for modeling kinetics of complex spatial self-propagating traveling-wave reactions is proposed. This approach is intended to replace well-known reaction-diffusion equations and self-propagating high-temperature synthesis (SHS) as methods for mathematical modeling of spatial propagation of chemical reactions. A chemical kinetic model for frontal polymerization of metal-containing monomers under this approach is suggested.

Facile synthesis of molybdenum disulfide (MoS2) quantum dots and its application in humidity sensing.

Molybdenum disulfide (MoS2) quantum dots (QDs) are successfully synthesized by facile synthesis using ultrasonication assisted liquid exfoliation technique. The high and low boiling point solvents: N-methyl-pyrrolidone (NMP) and ethanol-water solution have been used for synthesis of MoS2 QDs. Similar size distribution of MoS2 QDs synthesized in two different solvents have been observed from the transmission electron microscopy and average size of these QDs are ∼5 nm. The film of MoS2 QDs is used to fabricate humidity sensor. The large edge to volume ratio and high surface active sites of QDs enhanced the water adsorption even at low humidity environment (<37% RH). The humidity sensing analysis shows that sensing film of MoS2 QDs synthesized in ethanol-water has an average sensitivity of 2.78 MΩ/%RH with fast response time (11 s), good repeatability and high stability. In view of these results, the work is highly applicable to fabricate high performance MoS2 QDs humidity sensor.

Fabrication and characterization of ZnO-TiO2-PANI (ZTP) micro/nanoballs for the detection of flammable and toxic gases.

The present paper reports the in-situ chemical polymerization of nanocomposites thin film composed by titanium dioxide (TiO2), zinc oxide (ZnO) and polyaniline (PANI). It was found that nanocomposites sensor is highly selective and shows response to low concentration. To improve the sensing response characteristics of ZT thin film, PANI is incorporated. Thin film based LPG sensor of ZnO-TiO2-PANI composite was fabricated by spin coating of ZnO-TiO2 nanoparticles doped with PANI over inter digital electrodes (IDEs). The thin film was characterized by using XRD, SEM, TEM, UV-vis, BET and FTIR. It was also tested for gas sensing properties of LPG/NO2 which are well known flammable and toxic gases. The measured response for ZnO-TiO2-PANI based sensor was 87 for 2000 ppm of LPG and 412 for 20 ppm of NO2 at room temperature towards other testing gases together with Acetone, IPA, NH3 and CO2.

Synthesis and characterization of nanostructured MnO2-CoO and its relevance as an opto-electronic humidity sensing device.

Metal carboxylates are widely used in science and technology and have been the subject of intense studies due to the practical importance of their products. The present paper reports the synthesis of MnO2-CoO using metal carboxylates as precursors and the effect of humidity on the transmitted power through its thin film at room temperature. The refractive index of the material was found to be 1.445930 and the peak obtained from the photoluminescence spectra lies in the visible region. TEM reported a minimum grain size of ∼5.7 nm and SAED confirmed the crystalline nature of the material, which was further confirmed by XRD. Fluorescence characteristics also confirmed the low dimensionality of the material. The film was then investigated using SEM which exhibited the porous morphology. Through UV-Vis spectroscopy, it was found that the absorption of the film takes place in the UV region and the optical band-gap was observed to be 3.849 eV from the Tauc plot. The film was employed as a transmission based opto-electronic humidity sensor. Average sensitivity was found to be ∼2.225 µW/% RH with response and recovery times of 47 s and 59 s respectively. Experiments were repeated and the reproducibility of result was found to be ∼89%.