Parasitic capacitance modeling and measurements of conductive yarns for e-textile devices.

Conductive yarns have emerged as a viable alternative to metallic wires in e-Textile devices, such as antennas, inductors, interconnects, and more, which are integral components of smart clothing applications. But the parasitic capacitance induced by their micro-structure has not been fully understood. This capacitance greatly affects device performance in high-frequency applications. We propose a lump-sum and turn-to-turn model of an air-core helical inductor constructed from conductive yarns, and systematically analyze and quantify the parasitic elements of conductive yarns. Using three commercial conductive yarns as examples, we compare the frequency response of copper-based and yarn-based inductors with identical structures to extract the parasitic capacitance. Our measurements show that the unit-length parasitic capacitance of commercial conductive yarns ranges from 1 fF/cm to 3 fF/cm, depending on the yarn's microstructure. These measurements offer significant quantitative estimation of conductive yarn parasitic elements and provide valuable design and characterization guidelines for e-Textile devices.

Raman mapping of piezoelectric poly(l-lactic acid) films for force sensors.

Poly-l-lactic acid (PLLA) is a synthetic, biocompatible, biodegradable polymer with good piezoelectric properties. The prepared PLLA films were annealed in the oven at 140 °C for 0 h, 3 h, 12 h, and 24 h, respectively. The influences of temperature treatment time on the optoelectronic properties of the PLLA films and piezoelectric sensors based on them were investigated. The morphology and crystal structure of the PLLA films obtained under various post-processing conditions were examined by scanning electron microscopy, X-ray diffraction, Raman spectroscopy, and ATR-FTIR spectroscopy. The micromechanical equipment for tension-compression measurements was built in the laboratory for the tested piezoelectric sensors. The analysis of the structure shows that the increase in the crystallite size of the PLLA film influences the growth of the piezoelectric signal of the sensors based on them. The vibrational analysis of the PLLA films confirmed their crystal structure. The improvement in the structure and the stretching of the dipole C[double bond, length as m-dash]O for the film obtained after 3 h treatment increased the piezoelectric properties of the PLLA films. The analysis of Raman mapping added information that the area of the ordered phase of the PLLA films depends on the time of temperature treatment. The maximum value of the piezoelectric signal was 0.98 mV for sensors prepared on films annealed for 3 h at a load of 20 N. For films without temperature annealing at the same load, the maximum value was 0.45 mV. Thus, efficient converters of mechanical energy into electrical energy were obtained, which opens new innovative perspectives for the creation of flexible pressure sensors based on PLLA.

Utilizing Gradient Porous Graphene Substrate as the Solid-Contact Layer To Enhance Wearable Electrochemical Sweat Sensor Sensitivity.

Wearable sweat monitoring represents an attractive opportunity for personalized healthcare and for evaluating sports performance. One of the limitations with such monitoring, however, is water layer formation upon cycling of ion-selective sensors, leading to degraded sensitivity and long-term instability. Our report is the first to use chemical vapor deposition-grown, three-dimensional, graphene-based, gradient porous electrodes to minimize such water layer formation. The proposed design reduces the ion diffusion path within the polymeric ion-selective membrane and enhances the electroactive surface for highly sensitive, real-time detection of Na+ ions in human sweat with high selectivity. We obtained a 7-fold enhancement in electroactive surface against 2D electrodes (e.g., carbon, gold), yielding a sensitivity of 65.1 ± 0.25 mV decade-1 (n = 3, RSD = 0.39%), the highest to date for wearable Na+ sweat sensors. The on-body sweat sensing performance is comparable to that of ICP-MS, suggesting its feasibility for health evaluation through sweat.

An All-Fabric Tactile-Sensing Keypad with Uni-Modal and Ultrafast Response/Recovery Time for Smart Clothing Applications.

Keypads constructed from fabric materials are the ideal input devices for smart clothing applications. However, multi-modal reaction problems have to be addressed before they can be of practical use on apparels, i.e., the fabric-based keypads need to distinguish between the legitimate actions by the fingertips and the illegitimate deformations and stresses caused by human movements. In this paper, we propose to use the humidity sensor functionalized from graphene oxide (GO)-coated polyester fibers to construct the e-textile keypads. As the moisture level in the proximity of human fingertips is much higher (over 70%) than other parts of the human body, humidity sensing has many advantages over other tactility mechanisms. Experiments have demonstrated that the GO-functionalized fabric keypad has a stable uni-modal tactility only to fingertip touches, and it is not sensitive to deformation, pressure, temperature variation, and other ambient interferences. With biasing and sensing circuits, the keypad exhibits a quick response and recovery time (around 0.1 s), comparable to mechanical keyboards. To demonstrate its application on smart clothing, the keypad was sewn on a sweater and embroidered conductive yarns were used to control an MP3 player in the pocket.

Flexible frequency selective metamaterials for microwave applications.

Metamaterials have attracted more and more research attentions recently. Metamaterials for electromagnetic applications consist of sub-wavelength structures designed to exhibit particular responses to an incident EM (electromagnetic) wave. Traditional EM (electromagnetic) metamaterial is constructed from thick and rigid structures, with the form-factor suitable for applications only in higher frequencies (above GHz) in microwave band. In this paper, we developed a thin and flexible metamaterial structure with small-scale unit cell that gives EM metamaterials far greater flexibility in numerous applications. By incorporating ferrite materials, the thickness and size of the unit cell of metamaterials have been effectively scaled down. The design, mechanism and development of flexible ferrite loaded metamaterials for microwave applications is described, with simulation as well as measurements. Experiments show that the ferrite film with permeability of 10 could reduce the resonant frequency. The thickness of the final metamaterials is only 0.3mm. This type of ferrite loaded metamaterials offers opportunities for various sub-GHz microwave applications, such as cloaks, absorbers, and frequency selective surfaces.