An integrated electronic skin with biaxial sensitivity from a layered biphasic liquid metal/polymer film.

Research on electronic skin (e-skin) is dedicated to simulating natural skin for the perception of external mechanical stimuli. Currently, e-skin is ineffective in analyzing a single stimulus from different directions. This work successfully fabricates an integrated electronic skin (IES) with biaxial sensing capability through the combination of a biphasic liquid metal and porous foam. Remarkably different from traditional e-skin, the IES can analyze the type, strength, and area of an external mechanical stimulus from vertical and horizontal dimensions with a dual response (capacitive and resistive change, respectively). As a multifunctional sensor, the IES simultaneously responds to compression via capacitive change and tension via resistive change. Furthermore, 1000 cyclic compressions were conducted to confirm the electrical stability of the IES. Very subtle stimuli (e.g. thawing ice and touch) can be detected by the IES via biaxial detection. This work provides a new protocol for the development of future intelligent flexible electronics.

Ultrasensitive Soft Sensor from Anisotropic Conductive Biphasic Liquid Metal-Polymer Gels.

Subtle vibrations, such as sound and ambient noises, are common mechanical waves that can transmit energy and signals for modern technologies such as robotics and health management devices. However, soft electronics cannot accurately distinguish ultrasmall vibrations owing to their extremely small pressure, complex vibration waveforms, and high noise susceptibility. This study successfully recognizes signals from subtle vibrations using a highly flexible anisotropic conductive gel (ACG) based on biphasic liquid metals. The relationships between the anisotropic structure, subtle vibrations, and electrical performance are investigated using rheological-electrical experiments. The refined anisotropic design successfully realized low-cost flexible electronics with ultrahigh sensitivity (Gauge Factor: 12787), extremely low detection limit (strain: 0.01%), and excellent frequency recognition accuracy (>99%), significantly surpassing those of current flexible sensors. The ultrasensitive flexible electronics in this study are beneficial for diverse advanced technologies such as acoustic engineering, wearable electronics, and intelligent robotics.

Low incidence of hepatitis B virus reactivation in patients with hematological malignancies receiving novel anticancer drugs: A report from a high epidemic area and literature review.

BACKGROUND: More and more novel anticancer drugs have been approved for patients with hematological malignancies in recent years, but HBV reactivation (HBV-R) data in this population is very scarce. This study aimed to evaluated HBV-R risk in patients with hematological malignancies receiving novel anticancer drugs. METHODS: HBV markers and serum HBV DNA levels of patients with hematological malignancies receiving novel anticancer drugs in a tertiary cancer hospital were retrospectively collected. HBV-R risk in the whole cohort and subgroups was described. The relevant literature was reviewed to make a pooled analysis. RESULTS: Of 845 patients receiving novel anticancer drugs, 258 (30.5%) were considered at risk for HBV-R. The median duration of exposure to novel drugs was 5.6 (0.1-67.6) months. The incidence of HBV-R was 2.1% in patients with past HBV infection without prophylactic antiviral treatment (PAT) and 1.2% in all patients at risk of HBV-R. In a pooled analysis of 11 studies with 464 patients, the incidence of HBV-R was 2.4% (95% CI: 1.3-4.2) in all at-risk patients receiving novel anticancer drugs and 0.6% (95% CI: 0.03-3.5) in patients with anticancer drugs plus PAT. The incidence of death due to HBV-R was 0.4% (95% CI: 0.1-1.6) in all at-risk patients and 18.2% (95% CI: 3.2-47.7) in patients with HBV-R. CONCLUSION: Most episodes of HBV-R are preventable, and most cases with HBV-R are manageable. We recommend that novel anticancer drugs should not be intentionally avoided when treating cancer patients with HBV infection.

Scalable Fabrication of Metallic Conductive Fibers from Rheological Tunable Semi-Liquid Metals.

Conductive polymer fibers/wires (CPFs) are important materials in modern technologies due to their unique one-dimension geometry, electrical conductivity, and flexibility. However, the advanced applications of current CPFs are limited by their low electrical conductivities (<500 S/m) and poor interfacial interactions between conductive fillers (e.g., graphite) and polymers. Therefore, in current electrical applications, metal wires/foils like copper and aluminum are the most frequently utilized conductive fibers/wires instead of the inferior conductive CPFs. This work successfully addresses the heavy phase segregation between polymers and conductive inorganic materials to obtain semiliquid metal polymer fibers (SLMPFs) which exhibit an ultrahigh electrical conductivity (over 106 S/m), remarkable thermal processability, and considerable mechanical performance (Young's modulus: ~300 MPa). Semiliquid metal (gallium-tin alloy) with tunable viscosities is the key to achieve the excellent miscibility between metals and polymers. Both the rheological results and numerical simulations demonstrate the critical viscosity matching for the successful preparation of the fibers. More importantly, the fibers are adapted with classic polymer melt-processing like melt injection, which indicates the scalable production of the highly conductive fibers. The SLMPFs are highly promising substitutes for metal wires/fibers in modern electrical applications such as electricity transmission, data communication, and underwater works.

Plasma EBV-DNA and peripheral blood mononuclear cell EBV-DNA have disparate clinical relevance in patients with extranodal NK/T-cell lymphoma.

BACKGROUND: Extranodal NK/T-cell lymphoma (ENKTCL) is an Epstein-Barr virus (EBV)-related hematological malignancy. The presence of EBV-DNA in peripheral blood is a widely used ENKTCL tumor marker. However, there is no consensus on the preferred blood specimen type for EBV testing. Furthermore, discordance between EBV-based and imaging-based disease assessments is common, and how to interpret this discordance is important. METHOD: We retrospectively analyzed the data of ENKTCL patients in the Affiliated Cancer Hospital of Zhengzhou university and Sun Yat-sen University Cancer Center. All EBV-DNA and imaging-based disease assessment data were collected at diagnosis, during treatment, at the end of treatment, and during follow-up. We compared matched plasma EBV-DNA and peripheral blood mononuclear cell (PBMC) EBV-DNA and matched EBV-based and imaging-based assessments to uncover their clinical relevance. RESULT: A total of 450 patients with adequate data were included, of whom 278 had plasma EBV-DNA data, 250 had PBMC EBV-DNA data, and 78 had matched plasma and PBMC EBV-DNA data. No significant correlations were found between PBMC and plasma EBV-DNA and between PBMC EBV-DNA and imaging-based assessment, but patients with positive PBMC EBV-DNA at diagnosis or intermittently/persistently positive PBMC EBV-DNA during follow-up had poorer survival. In contrast, plasma EBV-DNA strongly correlated with lymphoma status. Detectable pre- and post-treatment plasma EBV-DNA was associated with significantly worse survival. Patients with early-stage disease who had detectable plasma EBV-DNA at the end of treatment shared similar survival to those with advanced-stage disease, even if their imaging-based assessments were negative. For disease relapse monitoring, 78 (55.7%) episodes of relapse were detected by both imaging and plasma EBV-DNA; 58 (41.4%) detected by plasma EBV-DNA earlier than imaging, with a median time of 9.3 (0.3 - 37.8) months; and only 4 (2.9%) detected by plasma EBV-DNA later than imaging. The sensitivities of plasma EBV-DNA, PET/CT, and CT/MRI were 97.1%, 76.8%, and 45.1%, respectively, and their specificities were 91.7%, 84.2%, and 96.7%, respectively. Analysis of EBV kinetic patterns in EBV+/imaging- episodes revealed that relapse occurred only in patients with intermittently/persistently positive plasma EBV-DNA. Persistent plasma EBV+ was also seen in patients after autologous hematopoietic stem cell transplantation. Occasional EBV+ was not associated with relapse. CONCLUSION: Plasma and PBMC EBV-DNA have different clinical relevance in ENKTCL patients. PBMC EBV-DNA does not correlate with imaging-based disease assessment. PBMC or even whole blood should not be used for response evaluation and relapse monitoring. However, PBMC EBV-DNA still has prognostic value. Plasma EBV-DNA is strongly related to tumor status and is not only a prognosticator at diagnosis and end of treatment, but also a sensitive marker in relapse monitoring compared to PET/CT and CT/MRI. The specificity of plasma EBV-DNA is relatively low, but when EBV-DNA kinetic patterns are considered, it can identify at-risk patients.

Fluidic phase-change materials with continuous latent heat from theoretically tunable ternary metals for efficient thermal management.

Phase-change materials (PCMs), as important energy storage materials (ESMs), have been widely used in heat dissipation for electronics. However, PCMs are encountering huge challenges since the extremely limited space in microelectronics largely suppresses the applied volume of PCMs, which demands excellent PCMs that can fully utilize the valuable latent heat. This work successfully found a universal strategy toward powerful ESMs from fluidic ternary metals (TMs, GaInSn as a representative TM in this work). TMs exhibit high thermal conductivity (20.3 W m-1 K-1) and significantly effective latent heat (115 J/cm3) and, more important, show continuous phase transition and full utilization of the valuable latent heat. Interestingly, theoretical prediction through ternary phase diagram is carried out to easily tune the melting range, latent heat, and fluidity (viscosity) of TMs to adapt with different service conditions. As a result, thermally conductive silicone grease can be conveniently fabricated via simple shear mixing of TM and polymers. Such thermally conductive TM grease inherits the merits of TM, exhibiting continuous thermal control over daily electronics according to thermal shock performance.

MiRNA-363-3p/DUSP10/JNK axis mediates chemoresistance by enhancing DNA damage repair in diffuse large B-cell lymphoma.

Anthracycline-based chemotherapy resistance represents a major challenge in diffuse large B-cell lymphoma (DLBCL). MiRNA and gene expression profiles (n = 47) were determined to uncover potential chemoresistance mechanisms and therapeutic approaches. An independent correlation between high expression of miRNA-363-3p and chemoresistance was observed and validated in a larger cohort (n = 106). MiRNA-363-3p was shown to reduce doxorubicin-induced apoptosis and tumor shrinkage in in vitro and in vivo experiments by ectopic expression and CRISPR/Cas9-mediated knockout in DLBCL cell lines. DNA methylation was found to participate in transcriptional regulation of miRNA-363-3p. Further investigation revealed that dual specificity phosphatase 10 (DUSP10) is a target of miRNA-363-3p and its suppression promotes the phosphorylation of c-Jun N-terminal kinase (JNK). The miRNA-363-3p/DUSP10/JNK axis was predominantly associated with negative regulation of homologous recombination (HR) and DNA repair pathways. Ectopic expression of miRNA-363-3p more effectively repaired doxorubicin-induced double-strand break (DSB) while enhancing non-homologous end joining repair and reducing HR repair. Targeting JNK and poly (ADP-ribose) polymerase 1 significantly inhibited doxorubicin-induced DSB repair, increased doxorubicin-induced cell apoptosis and tumor shrinkage, and improved the survival of tumor-bearing mice. In conclusion, the miRNA-363-3p/DUSP10/JNK axis is a novel chemoresistance mechanism in DLBCL that may be reversed by targeted therapy.

Transient Electrically Driven Stiffness-Changing Materials from Liquid Metal Polymer Composites.

Stiffness-changing materials (SCMs) have received lots of interests due to their reversible transition between their soft and rigid states for modern applications. However, the irreversible stiffness transition, slow response, and sustained external stimuli strictly hinder the broad utilizations of SCMs. Here, this work reports electrically driven SCMs based on supercooled liquid metals (LMs). A small voltage (5 V) can successfully initiate the stable and reversible stiffness change of the SCMs in electrolyte solution. Surprisingly, the LM-based SCMs (LM-SCMs) exhibited a significant change in 1000 times difference of moduli (65 kPa versus 79 MPa). Moreover, such a stiffness transition of the LM-SCM was ultrarapidly completed in a few seconds (<30 s). Importantly, after transient stimulation of LM nucleation, the rigidity of the LM-SCM could be maintained when the external stimulus (voltage) was removed, highly different from previously reported SCMs that require sustained energy to maintain their mechanical states. Based on the unique features of LM-SCMs, advanced robotics like smart valves and mechanical paws in seawater were successfully fabricated.

Tunable plasmonic gallium nano liquid metal from facile and controllable synthesis.

Liquid metal (LM) gallium (Ga) is famous for its metallic properties with unique fluidity and has been extensively utilized in modern technologies. However, chemical strategies towards nanostructured Ga are extremely challenging, which severely limits further advanced applications of Ga. This work reports a facile method, the classical galvanic replacement reaction (GRR), to readily realize the synthesis of uniform Ga nano LM through sacrificial seeds (zinc) and gallium ions (Ga3+). Different from the previous tedious Ga nanoparticle synthesis, the GRR can be achieved under mild conditions without involving any highly active reagents or special equipment. Surprisingly, the temperature heavily influences the results of GRR due to the unique solid-liquid phase transition of Ga LM. This work figures out the critical issues of temperature, oxygen and solvent in the GRR to successfully prepare Ga nanodroplets. Interestingly, the GRR provides a convenient strategy to control the size of Ga nano LM to mediate localized surface plasmon resonance (LSPR) in the ultraviolet region, which is hardly observed in noble metals. Besides, the nano Ga from GRR exhibits remarkable SERS detection capability with an extremely low limit of detection (10-6 M), which ranks as the highest enhancement factor with an average value exceeding 105 among Ga materials. Moreover, the SERS activity of the nano Ga shows no obvious decrease within 60 days, verifying its excellent storage stability. This work demonstrates a facile "bottom-up" chemistry for Ga LM, which could greatly benefit its potential applications in the future.

Stimuli-Driven Insulator-Conductor Transition in a Flexible Polymer Composite Enabled by Biphasic Liquid Metal.

Metal-polymer composites (MPCs) with combined properties of metals and polymers have achieved much industrial success. However, metals in MPCs are thought to be ordinary and invariable electrically conductive fillers in supportive polymers to show limited use in modern technologies. This work that is disclosed here, for the first time, introduces stimuli-driven transition from biphasic to monophasic state of liquid metal into polymer science to form dynamic soft conductors from the binary metal-polymer composites. The binary metal that exhibits temperature-driven reversible transition between solid and liquid states via a biphasic state is fabricated. A conducting stretchable polymer composite is developed using the judiciously chosen biphasic binary metal that undergoes conductor to insulator transition upon stretching. Insulating stretched films become conducting upon heating. A "tube" model elegantly describes such distinctive deformation/temperature-dependent behaviors. Moreover, the conducting polymer composite shows decrease in its resistance upon increasing the sample temperature. The resistance can be tuned from 1 to 108  Ω depending on the state of binary metal in the phase diagram. This work would build the intimate and interesting connection between metal phases and polymer science toward next-generation soft conductors and beyond.

Vapor-Mediated Stretchable and Reversible Conductors from Microporous Liquid Metal Polymers.

Flexible electronic devices have penetrated into a variety of industry sectors (i.e., consumer electronics, automotive, and medical) in human life, and this calls for better properties of stretchable conductive composites as the crucial elements. Traditionally, conductive inorganic fillers are incorporated in flexible polymers to prepare conductive composites, which falls short of the required properties in more demanding devices nowadays due to limited deformation, low conductivity, and poor processability. Herein, liquid metals were successfully incorporated in microporous polymer matrixes using a simple codissolving and film casting/solvent evaporation approach. The microporous liquid metal-embedded polymer (LMEP) was insulative as fabricated due to discontinuous liquid metals (LMs), while it became conductive upon stretching. Interestingly, the LMEP films showed a reversible insulator-conductor transition due to the regenerated pores in polymer matrix under organic vapor. Negligible changes in the resistance value were seen even after 50 solvent exposure-tensile strain cycles, demonstrating the excellent stability of the electrical properties of these films. Furthermore, most of the commercially available soluble polymers including rigid plastics and soft elastomers are suitable for the fabrication of LMEP. With the ideal characteristics, they have been successfully exploited in model alarm systems to prevent temperature overloads and solvent leakage, showcasing the great potential in next generation sensors used in industry settings.

A genetic predictive model for precision treatment of diffuse large B-cell lymphoma with early progression.

BACKGROUND: Early progression after the first-line R-CHOP treatment leads to a very dismal outcome and necessitates alternative treatment for patients with diffuse large B-cell lymphoma (DLBCL). This study aimed to develop a genetic predictive model for early progression and evaluate its potential in advancing alternative treatment. METHODS: Thirty-two hotspot driver genes were examined in 145 DLBCL patients and 5 DLBCL cell lines using next-generation sequencing. The association of clinical features, cell-of-origin, double expression, positive p53 protein, and gene alterations with early progression was analyzed, and the genetic predictive model was developed based on the related independent variables and assessed by the area under receiver operating characteristic. The potential of novel treatment based on the modeling was investigated in in-vitro DLBCL cell lines and in vivo xenograft mouse models. RESULTS: The frequency of CD79B (42.86% vs 9.38%, p = 0.000) and PIM1 mutations (38.78% vs 17.71%, p = 0.005) showed a significant increase in patients with early progression. CD79B and PIM1 mutations were associated with complex genetic events, double expression, non-GCB subtype, advance stage and unfavorable prognosis. A powerful genetic predictive model (AUROC = 0.771, 95% CI: 0.689-0.853) incorporating lactate dehydrogenase levels (OR = 2.990, p = 0.018), CD79B mutations (OR = 5.970, p = 0.001), and PIM1 mutations (OR = 3.021, p = 0.026) was created and verified in the other cohort. This modeling for early progression outperformed the prediction accuracy of conventional International Prognostic Index, and new molecular subtypes of MCD and Cluster 5. CD79B and PIM1 mutations indicated a better response to inhibitors of BTK (ibrutinib) and pan-PIM kinase (AZD 1208) through repressing activated oncogenic signaling. Since the two inhibitors failed to decrease BCL2 level, BCL2 inhibitor (venetoclax) was added and demonstrated to enhance their apoptosis-inducing activity in mutant cells with double expression. CONCLUSIONS: The genetic predictive model provides a robust tool to identify early progression and determine precision treatment. These findings warrant the development of optimal alternative treatment in clinical trials.

Hybrid Metallic Foam with Superior Elasticity, High Electrical Conductivity, and Pressure Sensitivity.

Growing interest has been received in metallic foams for their combined features of metals and porous structures. Coating metals on polymers have been the most prevalent method to fabricate hybrid metallic foams to inherit both the merits of metals and the mechanical flexibility of polymers. However, direct coating metals on foams is challenging and requires tedious synthesis, such as electrolysis and chemical reduction. This work reported a facile strategy to build hybrid metallic foams via in situ foaming of liquid metals (LM) and polyurethane. The fluidity and incompatibility of LM with porous polyurethane allow the coating of LM on polymers. LM-Foams exhibit high electrical conductivity (3.9 × 104 S/m), low density (ρ < 1 g/cm3), phenomenal elasticity (recover at 95% strain), and excellent mechanical stability (stable with 1000 compressive cycles). Interestingly, the ease of deformation for fluidic fillers in elastic polyurethane generates additional resistive change under pressure, showing unique sensory behaviors which were not observed in conventional conductive foams, such as high response sensitivity (gauge factor >25), short response time (202 ms), and outstanding electrical stability. The nonuniform size distribution of pores leads LM-Foams to show unusual position-dependent sensitivity, enabling advanced applications as password pads and electrical protection foams.

Metallo-Polyelectrolytes: Correlating Macromolecular Architectures with Properties and Applications.

Since the middle of the 20th century, metallopolymers have represented a standalone subfield with a beneficial combination of functionality from inorganic metal centers and processability from the organic polymeric frameworks. Metallo-polyelectrolytes are a new class of soft materials that showcase fundamentally different properties from neutral polymers due to their intrinsically ionic behaviors. This review describes recent trends in metallo-polyelectrolytes and discusses emerging properties and challenges, as well as future directions from a perspective of macromolecular architectures. The correlations between macromolecular architectures and properties are discussed from copolymer self-assembly, metallo-enzymes for biomedical applications, metallo-peptides for catalysis, crosslinked networks, and metallogels.

Decitabine-containing G-CSF priming regimen overcomes resistance of primary mediastinal neoplasm from early T-cell precursors to conventional chemotherapy: a case report.

Early T-cell precursor (ETP) leukemia represents a new subtype of T-lymphoblastic leukemia/lymphoma with unique immunophenotypes expressing T-cell and one or more of the myeloid/stem cell markers. Here, we report a young patient who had primary mediastinal mass and pleural effusion without bone marrow involvement. A CT-guided mediastinal biopsy and flow cytometry analysis of the pleural effusion revealed the blast cells to have complicated immunophenotypes: strongly expressed T-cell antigen CD7, myeloid-lineage antigens CD33 and CD13 and stem cell markers cTdT, CD34, and HLA-DR; dimly expressed myeloid-lineage specific antigen cMPO and B-cell antigen cCD79a; but did not express T-cell specific antigen cytoplasmic CD3 and B-cell specific antigen CD19. Clonal T-cell receptor rearrangement eventually determined the cell of origin from ETPs, not myeloblasts. The patient showed primary resistance to lymphoid and myeloid-directed induction therapy. Finally, low-dose decitabine combined with modified-CAG regimen induced a complete remission and allogeneic stem cell transplantation was performed as consolidation. The case indicates a primary mediastinal neoplasm from ETP with distinctive immunophenotype from leukemia type. Low-dose decitabine and modified-CAG regimen in combination with allogeneic stem cell transplantation may improve the outcome of patient.

L-Type Cav 1.2 Calcium Channel-α-1C Regulates Response to Rituximab in Diffuse Large B-Cell Lymphoma.

PURPOSE: One third of patients with diffuse large B-cell lymphoma (DLBCL) succumb to the disease partly due to rituximab resistance. Rituximab-induced calcium flux is an important inducer of apoptotic cell death, and we investigated the potential role of calcium channels in rituximab resistance. EXPERIMENTAL DESIGN: The distinctive expression of calcium channel members was compared between patients sensitive and resistant to rituximab, cyclophosphamide, vincristine, doxorubicin, prednisone (RCHOP) regimen. The observation was further validated through mechanistic in vitro and in vivo studies using cell lines and patient-derived xenograft mouse models. RESULTS: A significant inverse correlation was observed between CACNA1C expression and RCHOP resistance in two independent DLBCL cohorts, and CACNA1C expression was an independent prognostic factor for RCHOP resistance after adjusting for International Prognostic Index, cell-of-origin classification, and MYC/BCL2 double expression. Loss of CACNA1C expression reduced rituximab-induced apoptosis and tumor shrinkage. We further demonstrated direct interaction of CACNA1C with CD20 and its role in CD20 stabilization. Functional modulators of L-type calcium channel showed expected alteration in rituximab-induced apoptosis and tumor suppression. Furthermore, we demonstrated that CACNA1C expression was directly regulated by miR-363 whose high expression is associated with worse prognosis in DLBCL. CONCLUSIONS: We identified the role of CACNA1C in rituximab resistance, and modulating its expression or activity may alter rituximab sensitivity in DLBCL.

The effects of lncRNA MALAT1 on proliferation, invasion and migration in colorectal cancer through regulating SOX9.

BACKGROUND: For the study, we determine the potential biomarkers and uncover the regulatory mechanisms of lncRNA MALAT1 / miR-145 / SOX9 axis on the abilities of cell growth and cell metastasis of colorectal cancer. METHODS: Previously published dataset GSE18105 from GEO database was used for microarray analysis to identify differential-expressed lncRNAs and mRNAs. The miRNA which had targeted relationships with both lncRNA and mRNA was predicted using miRCode and Targetscan. The association between lncRNA and miRNA, miRNA and mRNA was verified using dual-luciferase reporter assay. Expression levels of lncRNA MALAT1, miR-145 and SOX9 were examined by quantitative RT-PCR analysis. The cell viability of two cancer cell lines was compared by CCK-8 assay. Colony formation was hired to detected cell proliferation. The cell cycle distribution and apoptotic cell rate were conducted by flow cytometry assay. Wound healing as well as transwell assay were compare the cell migration and cell invasion respectively among groups. The effect of MALAT1 on colorectal cancer in vivo was constructed by xenograft model. RESULTS: Significantly dysregulated lncRNAs and mRNAs were identified by microarray analysis. By experimental verification, MALAT1 and SOX9 were expressed in a high percentage of colorectal cancer tumors and cells, while miR-145 was in a low expression. We also identified miR-145 as a target of MALAT1 and SOX9. MALAT1 played a role in regulating cancer process by functioning as a competing endogenous RNA. Silencing MALAT1 could effectively decrease the expression level of SOX9, thus suppress cell viability and metastasis. Down-regulated MALAT1 could induce resistance of G1 phase in cell cycle, and facilitation of colorectal cancer cell apoptosis. Nude mice injected with cells transfected with si-MALAT1 had smaller tumor on size and weight. CONCLUSIONS: The regulatory function of lncRNA MALAT1 / miR-145 / SOX9 axis was revealed in colorectal cancer based on bioinformatics analysis. LncRNA MALAT1 could facilitate colorectal cancer cell proliferation, invasion and migration by down-regulating miR-145 and up-regulating SOX9. LncRNA MALAT1 could suppress cell cycle and apoptosis through MALAT1 / miR-145 / SOX9 axis.

ROMP for Metal-Organic Frameworks: An Efficient Technique toward Robust and High-Separation Performance Membranes.

Mixed-matrix membranes (MMMs) with excellent mechanical and separation performance are usually challenging to be fabricated due to the significant incompatibility between nanofillers and the polymer matrix. This work provides a facile technique to construct MMMs through covalently attaching metal-organic frameworks (MOFs) within the polymer matrix via ring-opening metathesis polymerization. Norbornene-modified UiO-66-NH2 was successfully copolymerized into polynorbornene matrix in less than 10 min. Owing to strong covalent interaction among MOFs and polymers, exceptional toughening effects for MMMs through cavitation were observed. For MMMs with 20 wt % MOF loading, 520 times improvement in mechanical toughness was realized in comparison with neat polymers (52 vs 0.1 MJ/m3), far exceeding most of the previous MMMs. Such MMMs exhibited excellent gas separation performance for H2/CO2 and H2/N2 with high H2 permeability at 91-230 barrers and H2/N2 and H2/CO2 selectivity at >1000 and 6-7, respectively, surpassing the 2008 Robeson Upper Bound. As a proof for the scalable preparation of MMMs, a large and thin MMM (dimension: 98 × 165 cm; thickness: 3-5 µm) was also prepared in the factory for gas separation.

MicroRNA-376a regulates cell proliferation and apoptosis by targeting forkhead box protein P2 in lymphoma.

The present study aimed to investigate microRNA-376a (miR-376a) expression in lymphoma, and to investigate the effect of miR-376a on cell proliferation and apoptosis at cytological and molecular levels. The expression of miR-376a in lymphoma issue and cells was detected by reverse transcription quantitative polymerase chain reaction (RT-qPCR), the expression of forkhead box protein P2 (FOXP2) was detected by RT-qPCR and western blot analysis, and the effect of miR-376a on cell proliferation and apoptosis were studied by an MTT assay and flow cytometry, respectively. Additionally, the expression levels of cyclin D2, cyclin A, cyclin B, apoptosis-associated proteins B-cell lymphoma 2 (Bcl-2) and Bcl-2-associated X protein (Bax) were detected by western blot analysis. Furthermore, the target of miR-376a was predicted and clarified using a dual-luciferase reporter assay. The expression of miR-376a was downregulated and FOXP2 was upregulated in lymphoma tissues and cells. miR-376a overexpression inhibited lymphoma cell proliferation and induced apoptosis by regulating the expression levels of cyclin D2, cyclin A, Bax and Bcl-2. The dual-luciferase reporter assay demonstrated that FOXP2 was a target of miR-376a. miR-376a overexpression induced apoptosis by targeting FOXP2. Overexpression of miR-376a inhibited cell proliferation and induced apoptosis by targeting FOXP2 in lymphoma. Therefore, miR-376a and FOXP2 have the potential for use as biomarkers of lymphoma.

Highly Emissive and Color-Tunable Perovskite Cross-linkers for Luminescent Polymer Networks.

Emissive cross-linkers are of special interest for polymer science because of their ability to endow polymer networks with luminescent properties. Methylammonium lead halide perovskite nanoparticles (MAPbCl xBr3- x NPs) are extensively explored for optical and optoelectronic applications. In this work, MAPbCl xBr3- x NPs with cross-linkable and polymerizable ligands are successfully prepared as new emissive cross-linkers for polymer networks. Commercially available reagent 2-aminoethyl methacrylate hydrochloride (AMHCl) can act as a ligand to stabilize MAPbBr3 NPs in solution. Compared with traditional ligands (oleic acid and oleylamine), AMHCl retains the architecture of perovskite effectively and affords polymerizable groups (vinyl) on the surface of perovskites. The as-prepared MAPbCl xBr3- x NPs can serve as cross-linkers in the radical polymerization of (meth)acrylates by UV-light to form polymer networks. Meanwhile, such cross-linkable emitters exhibit bright luminescence and color-tunability at room temperature, attributed by a unique halide exchange of perovskites between CH3NH3Br and AMHCl, which provides the polymer networks with varied emissive bands. These perovskite-crosslinked networks showed high air stability, water stability, and prominent photoluminescence quantum yields. On the basis of these excellent properties, white-light-emitting diodes were successfully fabricated from these perovskite-crosslinked composites with color-coordinate values at (0.316, 0.315), very close to the standard coordinates of white light. This work elucidates a new and convenient technique to convert nanocrystals into luminescent cross-linkers to build functional polymeric networks for technological applications.