Linking proteomic function and structure to electroactive biofilms development across electrode orientations.

The functionality of electroactive biofilms (EABs) is profoundly influenced by the proteomic dynamics within microbial communities, particularly through the participation of proteins in electron transfer. This study explored the impact of electrode surface orientation, measured by varying oblique angles, on the performance of EABs in bioelectrochemical systems (BES). Utilizing quantitative proteomics, results indicated that a slightly oblique angle (45°) optimized the spatial arrangement of microbial cells, enhancing electron transport efficiency compared to other angles tested. Specifically, the 45° orientation resulted in a 2.36-fold increase in the abundance of c-type cytochromes compared to the 90°. Additionally, Geobacter, showed a relative abundance of 83.25 % at 45°, correlating with a peak current density of 1.87 ± 0.04 A/m2. These microbial and proteomic adaptations highlighted the intricate balance between microbial behavior and the physical environment, which could be tuned to optimize operations. The findings provided new insights into the design and enhancement of BES.

A biocompatible electrode/exoelectrogens interface augments bidirectional electron transfer and bioelectrochemical reactions.

Bidirectional electron transfer is about that exoelectrogens produce bioelectricity via extracellular electron transfer at anode and drive cytoplasmic biochemical reactions via extracellular electron uptake at cathode. The key factor to determine above bioelectrochemical performances is the electron transfer efficiency under biocompatible abiotic/biotic interface. Here, a graphene/polyaniline (GO/PANI) nanocomposite electrode specially interfacing exoelectrogens (Shewanella loihica) and augmenting bidirectional electron transfer was conducted by in-situ electrochemical modification on carbon paper (CP). Impressively, the GO/PANI@CP electrode tremendously improved the performance of exoelectrogens at anode for wastewater treatment and bioelectricity generation (about 54 folds increase of power density compared to blank CP electrode). The bacteria on electrode surface not only showed fast electron release but also exhibited high electricity density of extracellular electron uptake through the proposed direct electron transfer pathway. Thus, the cathode applications of microbial electrosynthesis and bio-denitrification were developed via GO/PANI@CP electrode, which assisted the close contact between microbial outer-membrane cytochromes and nanocomposite electrode for efficient nitrate removal (0.333 mM/h). Overall, nanocomposite modified electrode with biocompatible interfaces has great potential to enhance bioelectrochemical reactions with exoelectrogens.

Interfacial OOH* mediated Fe(II) regeneration on the single atom Co-N-C catalyst for efficient Fenton-like processes.

Fe(II) regeneration is decisive for highly efficient H2O2-based Fenton-like processes, but the role of cobalt-containing reactive sites in promoting Fe(II) regeneration was overlooked. Herein, a single atom Co-N-C catalyst was employed in Fe(II)/H2O2 system to promote the degradation of diverse organic contaminants. The EPR and quenching experiments indicated Co-N-C significantly enhanced the generation of superoxide species, and accelerated hydroxyl radical generation for pollutant degradation. The electrochemical and surface composition analyses demonstrated the enhanced H2O2 activation and Fe(III)/Fe(II) recycling on the catalyst. Furthermore, in-situ Raman characterization with shell-isolated gold nanoparticles was employed to visualize the interfacial reactive intermediates and their time-resolved interaction. The accumulation of interfacial CoOOH* was confirmed when Co-N-C activated H2O2 alone, but it rapidly transformed into FeOOH* upon Fe(II) addition. Besides, the temporal variation of OOH* intermediates and the relative intensity of Co(III)-O and Co(IV)=O peaks depicted the dynamic interaction of reactive intermediates along the H2O2 consumption. With this basis, we proposed a mechanism of interfacial OOH* mediated Fe(II) regeneration, which overcame the kinetical limitation of Fe(II)/H2O2 system. Therefore, this study provided a primary effort to elucidate the overlooked role of interfacial CoOOH* in the Fenton-like processes, which may inspire the design of more efficient catalysts.

Membrane aerated biofilm reactor system driven by pure oxygen for wastewater treatment.

Pure oxygen is proposed for wastewater treatment due to its advantages over conventional air aeration. This study investigates a Pure Oxygen-based Membrane Aerated Biofilm Reactor (PO-MABR) for the first time under various operating conditions. The PO-MABR employs a gas-permeable membrane for direct diffusion of low-pressurized pure oxygen to the biofilm, ensuring exceptional carbon and nitrogen removal. The effectiveness of PO-MABR was investigated by varying operational conditions, including temperature, carbon-to-nitrogen ratio, gas pressure, and flow rate. Results indicate superior performance, with a 97% chemical oxygen demand removal and 19% higher total nitrogen removal than Air-Ventilated MABR (A-MABR) due to thicker biofilm and unique microbial structures in PO-MABR. Also, PO-MABR demonstrated resilience to low temperatures and effectively treated both high and low-strength wastewater. The findings emphasize the efficiency of PO-MABR in wastewater treatment, advocating for its adoption due to superior carbon and nitrogen removal across diverse operational conditions.

3D/2D Heterojunction Fabricated from RuS2 Nanospheres Encapsulated in Polymeric Carbon Nitride Nanosheets for Selective Photocatalytic CO2 Reduction to CO.

Micro/nanostructure control of heterostructures is still a challenge for achieving high efficiency and selectivity of photocatalytic CO2 conversion. In this work, a new three-dimensiona/two-dimensional (3D/2D) heterostructure is fabricated by encapsulating RuS2 nanospheres in the interlayer of mesoporous polymeric carbon nitride (PCN) nanosheets based on an in situ growth and polymerization strategy. The unique microstructure of the obtained 3D/2D RuS2/PCN heterojunction can effectively improve the transfer and separation efficiency of photogenerated charge carriers, reduce the mass transfer resistance of CO2 toward active sites, and provide a confined reaction space, thus propelling the photocatalytic CO2 reduction to CO with high selectivity. The CO yield over the optimal 5%-RuS2/PCN sample reaches 4.2 and 2.8 times as high as that of single PCN and RuS2 within 4 h, respectively. Furthermore, the plausible charge transfer mechanism and CO2 reduction path are revealed by time-dependent in situ Fourier transform infrared (FT-IR) spectra combined with photophysical, electrochemical, and photoelectrochemical techniques and density functional theory (DFT) calculations. This work develops the microstructural engineering design strategy of PCN-based heterojunctions for selective photocatalytic CO2 fuel conversion.

Organic and inorganic nitrogen removals by an ureolytic heterotrophic nitrification and aerobic denitrification strain Acinetobacter sp. Z1: Elucidating its physiological characteristics and metabolic mechanisms.

Although heterotrophic nitrification-aerobic denitrification (HN-AD) is promising in nitrogen removal, it remains unclear for most HN-AD strains in physiological characteristics and metabolic mechanisms. In this study, a newly isolated strain Acinetobacter sp. Z1 converted not only inorganic nitrogen, but also organic nitrogen to N2. Among them, urea was the preferential nitrogen substrate. Single-factor experiments showed that efficient HN-AD process occurred with acetate as carbon source, C/N ratios of 12 for NH4+-N and 15 for NO3--N, pH 8, 30 °C, DO of ∼5.8 mg/L and salinity less than 1.5 %. Subsequently, response surface analysis was applied to predict the optimal growth conditions. Its complete genome annotation in combination with enzymatic activity assay and nitrogen balance calculation showed that at least four pathways involved in nitrogen metabolism. This work indicates that ureolytic strain Z1 could be prepared as bacterial agents with other HN-AD strains to treat urea-containing wastewater like urine from urban community.

Performance and mechanisms exploration of nano zinc oxide (nZnO) on anaerobic decolorization by Shewanella oneidensis MR-1.

Although the ecological safety of nanomaterials is of widespread concern, their current ambient concentrations are not yet sufficient to cause serious toxic effects. Thus, the nontoxic bioimpact of nanomaterials in wastewater treatment has attracted increasing attention. In this study, the effect of nano zinc oxide (nZnO), one of the most widely used nanomaterials, on the anaerobic biodegradation of methyl orange (MO) by Shewanella oneidensis MR-1 was comprehensively investigated. High-dosage nZnO (>0.5 mg/L) caused severe toxic stress on S. oneidensis MR-1, resulting in the decrease in decolorization efficiency. However, nZnO at ambient concentrations could act as nanostimulants and promote the anaerobic removal of MO by S. oneidensis MR-1, which should be attributed to the improvement of decolorization efficiency rather than cell proliferation. The dissolved Zn2+ was found to contribute to the bioeffect of nZnO on MO decolorization. Further investigation revealed that low-dosage nZnO could promote the cell viability, membrane permeability, anaerobic metabolism, as well as related gene expression, indicating that nZnO facilitated rather than inhibited the anaerobic wastewater treatment under ambient conditions. Thus, this work provides a new insight into the bioeffect of nZnO in actual environment and facilitates the practical application of nanomaterials as nanostimulants in biological process.

Low carbon-to-nitrogen ratio digestate from high-rate anaerobic baffled reactor facilitates heterotrophic/autotrophic nitrifiers involved in nitrogen removal.

In this study, baffled anaerobic-aerobic reactors (AOBRs) with modified basalt fiber (MBF) carriers and felt were used to treat domestic wastewater (DWW). The influent was first treated in anaerobic compartments, with the NH4+-N containing digestate refluxed into aerobic compartment for nitrification. The nitrified liquid was channeled to the anaerobic compartments for further denitrification. Under optimal conditions, AOBR with MBF carriers could remove 91% chemical oxygen demand (COD) and 81% total nitrogen (TN), with biomass production increased by 7.6%, 4.5% and 8.7% in three successive anaerobic compartments compared to the control. Biological viability analysis showed that live cells outnumbered dead cells in bio-nests. Metagenomics analysis showed that multiple metabolic pathways accounted for nitrogen conversion in anaerobic and aerobic compartments. More importantly, low COD/TN ratio digestate facilitated heterotrophic nitrification-aerobic denitrification (HN-AD) species growth in aerobic compartment. This study provides a promising strategy to source treatment of DWW from urban communities.

Rapid cultivation of anammox sludge based on Ca-alginate cell beads.

Current gel entrapment technology has certain advantages for the enrichment of anammox sludge. In this study, the optimal preparation conditions and cultivation equipment of Ca-alginate cell beads for the culturing anammox sludge were proposed. The preparation parameters of the Ca-alginate cell beads were as follows: 3% sodium alginate, 4% CaCl2, VSA:Vcell = 1:1, a drop height of 9 cm, stirring speed of 300 rpm, and cross-linking time of 24 h. The prepared cell beads were regular spheres with a uniform size and hard texture. Throughout the 9 days of cultivation, the number of anammox bacteria in the Ca-alginate cell beads was 4.3 times that of the initial sludge, and the color of the cell beads changed from yellowish-brown to reddish-brown. Scanning electron microscopy (SEM) analysis showed that the SA gel beads had a good microporous structure. The fluorescence in situ hybridization (FISH) results illustrated that the bacteria were mostly dispersed inside the Ca-alginate cell beads. Additionally, the qPCR results implied that only a relatively small amount of anammox biomass (2.74×106 copies/gel-bead) was required to quickly start the anammox process. The anammox bacteria in the Ca-alginate cell beads grew with a fast growth rate in a short period and exhibited high activity due to diffusion limitations. In addition, the anammox bacteria cultivated in the Ca-alginate cell beads could adapt to the increase in substrate concentration in a short period. The optimal incubation time of this gel entrapment method for anammox sludge was no more than 17 days under the experimental conditions of this work. Therefore, this simple and practicable gel entrapment method may serve as a suitable pre-culture means for the rapid enrichment of anammox bacteria.

Decomplexation of Cu(II)-EDTA by synergistic activation of persulfate with alkali and CuO: Kinetics and activation mechanism.

Heavy metals usually coexist with a variety of chelating agents to form heavy metal complexes in industrial wastewater. The decomplexation of heavy metal complexes is the crucial step before the removal of heavy metals via alkaline precipitation process. An efficient synergistic activation of persulfate (PS) with alkali and CuO was used for the simultaneous decomplexation of Cu-ethylenediamine tetraacetic acid (Cu(II)-EDTA) (3.14 mM) and the Cu(II) precipitation. The experimental results demonstrated that nearly complete removal of Cu(II) could be achieved by synergistic activation of PS with alkali and CuO at pH 11 after 2 h of decomplexation reaction. However, sole PS could not effectively decomplex Cu(II)-EDTA (13.5%), while the alkaline activation of PS could accomplish 57.0% removal of Cu(II). Radical scavenger tests indicated that reactive oxygen species (ROS) including SO4•-, •OH and O2•- were responsible for the decomplexation of Cu(II)-EDTA in the synergistic activation of PS with alkali and CuO. As a heterogeneous activator, CuO possessed excellent reusability and long-lasting catalytic activity and the rate constant value (k) of Cu(II) removal showed an increase (from 0.0326 min-1 in the first cycle to 0.0491 min-1 in the 24th cycle) with 24 cycles experiments. Furthermore, the biotoxicity evaluation of treated solution revealed that the biotoxicity of Cu(II)-EDTA contaminated wastewater could be effectively mitigated by the synergistic activation of PS with alkali and CuO because of the efficient precipitation of Cu(II) and oxidative degradation of EDTA organic ligands, which was favorable for the subsequent biochemical treatment.

Re-evaluation of the environmental hazards of nZnO to denitrification: Performance and mechanism.

Numerous studies have shown that zinc oxide nanoparticles (nZnO) have an inhibitory effect on wastewater biotreatment, where doses exceeding ambient concentrations are used. However, the effect of ambient concentrations of ZnO (<1 mg/L) on anaerobic digestion processes is not clear. Herein, this study comprehensively explored the impact of nZnO on the denitrification performance and core microbial community of activated sludge under ambient concentrations. Results showed that only 0.075 mg/L nZnO had shown a beneficial effect on nitrogen removal by activated sludge. When nZnO concentration reached 0.75 mg/L, significant enhancement of nitrate reduction and mitigation of nitrite accumulation were observed, indicating a remarkable stimulatory effect on nitrogen removal. Simultaneously, nZnO could weaken the sludge surface charge and improve the secretion of extracellular polymeric substances, thus enhancing sludge flocculation for denitrification. Microbial community analysis revealed that nZnO exposure increased the relative abundance of denitrifying bacteria, which could contribute to the reinforcement of traditional denitrification. Furthermore, exogenous addition of NH4+ significantly inhibited the accumulation of nitrite, implying that nZnO had a potential to improve the denitrification process via a partial denitrification-anammox pathway. Considering current ambient concentration, the stimulatory effect shown in our work may better represent the actual behavior of ZnO in wastewater biotreatment.

Heterotrophic nitrification and aerobic denitrification process: Promising but a long way to go in the wastewater treatment.

The traditional biological nitrogen removal (BNR) follows the conventional scheme of sequential nitrification and denitrification. In recent years, novel processes such as anaerobic ammonia oxidation (anammox), complete oxidation of ammonia to nitrate in one organism (comammox), heterotrophic nitrification and aerobic denitrification (HN-AD), and dissimilatory nitrate reduction to ammonium (DNRA) are gaining tremendous attention after the discovery of metabolically versatile bacteria. Among them, HN-AD offers several advantages because individual bacteria could achieve one-stage nitrogen removal under aerobic conditions in the presence of organic carbon. In this review, besides classical BNR processes, we summarized the existing literature on HN-AD bacteria which have been isolated from diverse habitats. A particular focus was given on the diversity and physiology of HN-AD bacteria, influences of physiological and biochemical factors on their growth, nitrogen removal performances, as well as limitations and strategies in unraveling HN-AD metabolic pathways. We also presented case studies of HN-AD application in wastewater treatment facilities, pointed out forthcoming challenges of HN-AD in these systems, and presented modulation strategies for HN-AD application in engineering. This review may help improve the existing design of wastewater treatment plants by harnessing HN-AD bacteria for effective nitrogen removal.

Abiotic-biotic hybrid for CO2 biomethanation: From electrochemical to photochemical process.

Converting CO2 into sustainable fuels (e.g., CH4) has great significance to solve carbon emission and energy crisis. Generally, CO2 methanation needs abundant of energy input to overcome the eight-electron-transfer barrier. Abiotic-biotic hybrid system represents one of the cutting-edge technologies that use renewable electric/solar energy to realize eight-electron-transfer CO2 biomethanation. However, the incompatible abiotic-biotic hybrid can result in low efficiency of electron transfer and CO2 biomethanation. Herein, we present the comprehensive review to highlight how to design abiotic-biotic hybrid for electric/solar-driven CO2 biomethanation. We primarily introduce the CO2 biomethanation mechanism, and further summarize state-of-the-art electrochemical and photochemical CO2 biomethanation in hybrid systems. We also propose excellent synthetic biology strategies, which are useful to design tunable methanogenic microorganisms or enzymes when cooperating with electrode/semiconductor in hybrid systems. This review provides theoretical guidance of abiotic-biotic hybrid and also shows the bright future of sustainable fuel production in the form of CO2 biomethanation.

Calcium modified basalt fiber bio-carrier for wastewater treatment: Investigation on bacterial community and nitrogen removal enhancement of bio-nest.

Modified basalt fiber (MBF) is a sustainable material studied as novel wastewater treatment bio-carrier recently. This work studied the effects of calcium modification on the bacterial affinity of modified fiber (Ca-MBF), bacterial community, and nitrogen removal performance. Results showed that Ca-MBF with hydrophilic (62.66°) and positively-charged (7.80 mV) surface accelerated bacterial attachment. Volatile suspended solids on Ca-MBF (5.46 g VSS/g fiber) were increased by 2.61 times after modification, with high bacterial activity when bio-carriers were cultured in activated sludge. Extracellular polymeric substances on Ca-MBF was 4.35 times higher and consisted of more protein. Bio-nests with unique aerobic/anaerobic structure formed on the ultrafine carriers in bioreactor. Ca-MBF bioreactor exhibited total nitrogen removal efficiency above 72.2% and COD removal efficiency above 94.2% with more stable performance than unmodified carrier in long-term treatment using synthetic domestic wastewater.16S rRNA gene sequencing revealed enhanced abundance of nitrifying and denitrifying bacteria in Ca-MBF bio-nest.

Enhancement of nitrogen removal in hybrid wastewater treatment system using ferric citrate modified basalt fiber biocarrier.

Developing biofilm carriers is of great significance for efficient wastewater treatment. In this work, ferric citrate was used to modify inorganic basalt fiber (BF) biocarrier, thus improving its surface properties and the nitrogen removal in hybrid wastewater treatment system. The results showed that the iron element on modified basalt fiber (Fe-MBF) existed in the forms of ferric citrate, Fe(OH)3, Fe2O3, and FeO. The ferric deposition increased the surface roughness, hydrophilicity and reduced the electronegativity of BF. The water contact angle of BF and Fe-MBF was 117.46° and 64.85°, respectively. The surface zeta potential of BF was -17.64 mV, but shifted positively (-8.67 mV) after deposition modification. The microorganism adhesion tests showed that the attached biomass and extracellular polymeric substances (EPS) content on Fe-MBF biocarrier significantly increased and the attached bacteria had also high viability. The Fe-MBF biocarrier showed good nitrogen removal performance in the hybrid bioreactor, with total nitrogen removal efficiency up to 95.35±0.82%, increasing by about 16% compared to that with unmodified BF biocarrier. This work also provided a green modification strategy to enhance biofilm carrier in wastewater treatment.

The removal of Cu(II)-EDTA chelates using green rust adsorption combined with ferrite formation process.

Classical adsorbents such as activated carbon are inefficient to remove Cu(II)-EDTA in solution. Moreover, the heavy metals in the generated sludge can easily be dissolved back into solution. In this research, a novel strategy developed by coupling green rust adsorption and ferrite formation technology was proposed for Cu(II)-EDTA chelate removal. At the adsorption stage, green rust sulfate (GRME(SO42-)) showed a high adsorption efficiency of chelated copper, with a capacity of 126.41 mg g-1, compared to other classical adsorbents. During the ferrite formation stage, GRME(SO42-)-based precipitate with high moisture content and slow settling rate could be transformed into ferrite-based precipitate with low moisture content and rapid settling rate. The volume and moisture content of ferrite were 2.20 and 1.45 times lower than those of GRME(SO42-) and the sedimentation velocity of ferrite was also 1.23 times higher than that of GRME(SO42-), which strongly demonstrated the necessity of the ferrite formation process. Toxicity characteristic leaching procedure (TCLP) test results showed that the metallic copper of GRME(SO42-) sludge could be more easily dissolved back into solution than that of ferrite precipitate under weak-acid conditions, indicating the stability of ferrite. In addition, after the ferrite process, the generated sludge exhibited soft magnetism and could be quickly separated within few seconds using an external magnetic field. All these results showed that the combined green rust adsorption with ferrite formation method was an efficient, recyclable and eco-friendly method for the treatment of wastewater containing Cu(II)-EDTA.

Anaerobic reduction of high-polarity nitroaromatic compounds by electrochemically active bacteria: Roles of Mtr respiratory pathway, molecular polarity, mediator and membrane permeability.

Electrochemically active bacteria (EAB) are effective for the bioreduction of nitroaromatic compounds (NACs), but the exact reduction mechanisms are unclear yet. Therefore, 3-nitrobenzenesulfonate (NBS) was used to explore the biodegradation mechanism of NACs by EAB. Results show that NBS could be anaerobically degraded by Shewanella oneidensis MR-1. The generation of aminoaromatic compounds was accompanied with the NBS reduction, indicating that NBS was biodegraded via reductive approach by S. oneidensis MR-1. The impacts of NBS concentration and cell density on the NBS reduction were evaluated. The removal of NBS depends mainly on the transmembrane electron transfer of S. oneidensis MR-1. Impairment of Mtr respiratory pathway was found to mitigate the reduction of NBS, suggesting that the anaerobic biodegradation of NBS occurred extracellularly. Knocking out cymA severely impaired the extracellular reduction ability of S. oneidensis MR-1. However, the phenotype of ΔcymA mutant could be compensated by the exogenous electron mediators, implying the trans-outer membrane diffusion of mediators into the periplasmic space. This work provides a new insight into the anaerobic reduction of aromatic contaminants by EAB.

Treatment of high-load organic wastewater by novel basalt fiber carrier media.

The carrier medium plays a key role in improving existing remediation potential of conventional biological contact oxidation reactors. In this study, a biological contact oxidation reactor was constructed using basalt fiber (R-BF) as a biological carrier. The bioreactor performance was investigated in terms of reduction in chemical oxygen demand (COD), ammonium nitrogen (NH4+-N), and total nitrogen (TN) at organic loadings rate of 15.243 kg/m3·d and nitrogen loading rate of 1.068 kg/m3·d. We found that COD, NH4+-N, and TN were reduced to 99.1%, 97.9%, and 97.8%, respectively. Within the R-BF, a bio-nest was developed which had abundant pores and channels and supported successful movement of nutrients, resulting in high biological activity (55.78%). The microbial communities within the bio-nest were diverse and rich and sludge production during operation was minimal. This makes BF a promising application for wastewater treatment. This research might be useful in the construction of integrated bioreactors that can operate under high organic and nitrogen loadings rates with reduced energy consumption, i.e. 75% in this study.

Weighted Subject-Semi-Independent ERP-based Brain-Computer Interface.

Subject-independent brain-computer interfaces (SI-BCIs) which require no calibration process, are increasingly affect researchers in BCI field. The efficiencies (accuracies), however, were not satisfying till now. In this paper, we proposed a weighted subject-semi-independent classification method (WSSICM) for ERP based BCI system in which a few blocks data of target subject were used. 47 participants were attended in this study. We compared the accuracies of proposed method with traditional subject-specific classification method（SSCM） which used 15 blocks data of target subject. The averaged accuracies were 95.2% for the WSSICM at 5 blocks and 95.7% for the SSCM at 15 blocks. The accuracies of two method did not show significant difference (p-value=0.652). The method we proposed in this paper which could reduce the calibration time can be used for future BCI systems.

Treatment of simulated electroplating wastewater containing Ni(II)-EDTA by Fenton oxidation combined with recycled ferrite process under ambient temperature.

Developing low cost and efficient method for the treatment of electroplating wastewater containing heavy metals complexed with chelating agent has attracted increasing attention in industrial wastewater treatment. This study involved a system combining Fenton oxidation (FO) and recycled ferrite (RF) process for treating synthetic solution containing Ni(II)-EDTA at ambient temperature. In this system, the FO reaction can produce hydroxyl radicals with high redox potential to decomplex the metal-organic complexes and degrade the organics, thereby enhancing the removal efficiency of heavy metals. The RF process is to incorporate the non-iron metal into the spinel ferrites at room temperature, and stabilize the sludge. As a result, the toxicity characteristic leaching procedure can fulfill the relevant standards. Furthermore, the ferrous ions in Fenton reaction could be used as the source of irons in RF process. After treatment by the combined process, the effluent water fulfills the relevant standard in China. In comparison with conventional alkaline precipitation, the sludge sedimentation velocity of FO-RF is 2.16 times faster than that of conventional alkaline precipitation and the volume of sludge is reduced by half, which strongly demonstrated the advantages of the presented FO-RF system and indicated the huge potential for the treatment of EDTA-chelated nickel.