Comparison of methodologies to quantify phytate phosphorus in diets containing phytase and excreta from broilers.

The use of a suitable methodology to quantify the phytate phosphorus (Pphy) content in both the feed and the excreta from broilers is required to enable accurate calculation of the catalytic efficiency of the phytase supplemented in the feed. This study was conducted to compare 2 analytical methodologies (colorimetry and also high-performance liquid chromatography with a refractive index detector) in order to calculate the phytase efficiency by utilizing the results from the methodology that was shown to be the most appropriate. One hundred and twenty broilers were distributed in a (4+1)×2 factorial arrangement, corresponding to 4 diets that were equally deficient in P supplemented with increasing levels of phytase (0, 750, 1,500, and 2,250 units of phytase activity - FTU - per kg of feed) plus 1 positive control diet without phytase, supplied to male and female birds. The result indicated that the colorimetric methodology with an extraction ratio of 1:20 (mass of sample in g:volume of the solvent extractor in mL) was shown to be the most adequate. There was no interaction between the phytase level and the sex of the broilers (p>0.05). Males consumed 12% more Pphy than did females (p<0.01), but the sex of the broilers did not affect (p>0.05) the excretion and retention coefficient of Pphy. The increase in the phytase level of the diet reduced (linear, p<0.01) the Pphy excretion. The greatest Pphy retention was estimated at 87.85% when the diet contained 1,950 FTU/kg (p<0.01), indicating that it is possible to reduce the inorganic P in the formulation at an amount equivalent to 87.85% of the Pphy content present in the feed, which, in this research, corresponds to a decrease in 2.86 g of P/kg of the feed.

Morphological effects on the hard palatine mucosa of Calomys callosus submitted to experimental chronic alcoholism.

The morphological effects of ethanol ingestion on the hard palatine mucosa of adult male Calomys callosus were observed. Twenty rodents were divided into two experimental groups: the control group received solid diet, Purina rat chow, and tap water ad libitum; the alcoholic group received the same solid diet and ethanol P.A. diluted 20% in water (v/v). After 270 days of treatment, all animals were sacrificed and the hard palatine mucosa were prepared for TEM and SEM methods. The epithelial cells of the alcoholic group showed some alterations like cytoplasmatic lipid droplets, pycnotic nucleus and increased mitochondrial size. The lamina propria also presented intense lipid droplets accumulation. The morphological changes suggested that chronic ethanol consumption was able to modify the integrity of the mucosa.

A morphological and tensile bond strength evaluation of an unfilled adhesive with low-viscosity composites and a filled adhesive in one and two coats.

OBJECTIVE: The purpose of this study was to measure the tensile bond strength (TBS) testing of resin composite to dentin of three low-viscosity composites, in association with an unfilled adhesive, and a filled adhesive one and two coats respectively, and to evaluate and compare the SEM morphological observations. METHODS: The labial surface of 120 bovine lower incisors were ground to obtain a flat dentin surface allowing demarcation of a 4 mm diameter area with adhesive tape. The teeth were randomly divided in six groups of 20 each. The dentin of each ground surface was etched with 35% H(3)PO(4) for 15s, followed by application of the respective adhesive: Single Bond (SB) for Groups 1, 2, 3 and 6; Optibond Solo (OS) for Groups 4 and 5. In Groups 1 and 4, a resin composite rod with a wire loop was luted directly to the adhesive surface with Z100. Group 2 received an intermediate layer of Flow It (FI) composite; Group 3 received an intermediate layer of Protect Liner F (PLF) composite; Group 5 received a second coat of OS; and Group 6 received an intermediate layer of an experimental low-viscosity composite (EM). A resin composite rod was luted to the surface of each specimen with Z100 resin composite. All specimens were stored in distilled water at 37 degrees C for 24h prior to TBS testing. Each specimen was inspected by SEM and classified according to adhesive or cohesive failure mode. One specimen of each group was cut longitudinally, polished and prepared for SEM observation. RESULTS: The TBS values were: Group 1 (7.86MPa+/-2.28), Group 2 (7.62MPa+/-1.85), Group 3 (7.60MPa+/-2.14), Group 4 (7.96MPa+/-2.36), Group 5 (7.50MPa+/-2.70) and Group 6 (7.18MPa+/-2.40). No significant statistical differences were observed among the groups. However, the analyses of the failure mode presented a considerable variation. SIGNIFICANCE: The use of a filled adhesive or an unfilled adhesive along with a low-viscosity composite as an intermediate layer may provide a stress absorbing layer, whereby improving the preservation of the bonded interface area.