RESUMEN
Introduction: Cannabis sativa L. inflorescences are widely used in the medicinal field as treatments for a variety of symptoms and illnesses due to their unique phytochemicals such as cannabinoids and terpenes. Common postharvest procedures for cannabis inflorescence include trimming, followed by drying, curing, and subsequent storage. The postharvest trimming step, particularly its timing (pre- or post-drying) and the extent of trimming, is not optimally refined in terms of its impact on the cannabinoid and terpene content. In this study, our objective was to identify the optimal trimming conditions for a commercially available medicinal cannabis hybrid chemovar, with the goal of maximizing its cannabinoid and terpene content. Methods: To achieve this, we investigated the effects of pre- versus post-drying trimming and evaluated the impact of mild versus aggressive trimming prior to drying on the cannabinoid and terpene profiles using liquid and gas chromatography. Results: Our results indicated that pre-drying mild trimming yielded the highest cannabinoid concentration, possibly due to optimal balance between stress signals and precursor influx from the sugar leaves to the inflorescence. On the other, post-drying trimming yielded the highest terpene content. Conclusion: Identifying the optimal trimming conditions that maximize both cannabinoid and terpene levels in cannabis is challenging. Therefore, growers face a decision in their trimming practices: to prioritize either enhanced cannabinoid content or increased aromatic terpene concentrations, as optimizing for both simultaneously appears to be difficult.
RESUMEN
Since 2004, the prevalence of lameness in sheep flocks in England has reduced as farmers have adopted evidence-based management practices to control lameness. In 2011, the Farm Animal Welfare Council proposed a target prevalence of <2% lameness in sheep by 2021. This study investigated whether that target had been achieved and determined which practices were associated with prevalence of lameness. A postal questionnaire was sent to 1000 randomly selected farmers to investigate the prevalence of lameness and management practices in 2022. The geometric mean prevalence of lameness was <2% in ewes and lambs, but the median was 3%; approximately 26% flocks had <2% lameness. Data were analysed using robust variable selection with multivariable linear models. Farmers that quarantined ewes for ≥3 weeks and did not use foot bathing or foot trimming to prevent lameness had 40-50% lower prevalence of lameness than those not using these practices. Fewer farmers (19.0%) were always using parenteral antimicrobials to treat footrot, an effective practice, than in previous research (49.7%). We conclude that the target of <2% lameness in England has been achieved by 26% of farmers, and further work is required for more farmers to follow the evidence-based management practices to minimise lameness.
RESUMEN
BACKGROUND: Cattle lameness is a significant welfare and economic problem facing the livestock industry. Published research has investigated foot trimming practices in dairy herds, but little is known about the practices in beef herds. Therefore, the objective of this study was to obtain information about the current practices of professional cattle foot trimmers concerning beef cattle within the UK. METHODS: An online survey comprising 16 questions was created using the Joint Information Systems Committee platform. The survey was open for 3 months. RESULTS: There was a significant difference (p < 0.05) between the proportions of dairy cattle and beef cattle receiving preventative foot trims. Digital dermatitis was the most commonly recorded cause of lameness when a lame beef animal was trimmed by the respondents, followed by white line disease. A thematic analysis of foot trimmers' opinions of barriers to engagement on beef farms is presented, in addition to their opinions on veterinary involvement with beef lameness. LIMITATIONS: Distribution bias may have affected the results, as the survey was distributed online with support from the Cattle Hoof Care Standards Board and the National Association of Cattle Hoof Trimmers. The percentage of foot trimmers not affiliated with either professional body is not known. CONCLUSION: Further research on the impact of lameness on suckler and finishing cattle, including investigations into preventative actions to reduce lameness in beef systems, is warranted.
Asunto(s)
Enfermedades de los Bovinos , Cojera Animal , Animales , Bovinos , Cojera Animal/prevención & control , Reino Unido/epidemiología , Enfermedades de los Bovinos/prevención & control , Encuestas y Cuestionarios , Crianza de Animales Domésticos/métodos , Pezuñas y Garras/patología , Humanos , Enfermedades del Pie/veterinaria , Enfermedades del Pie/prevención & control , FemeninoRESUMEN
The abrasive waterjet machining process was introduced in the 1980s as a new cutting tool; the process has the ability to cut almost any material. Currently, the AWJ process is used in many world-class factories, producing parts for use in daily life. A description of this process and its influencing parameters are first presented in this paper, along with process models for the AWJ tool itself and also for the jet-material interaction. The AWJ material removal process occurs through the high-velocity impact of abrasive particles, whose tips micromachine the material at the microscopic scale, with no thermal or mechanical adverse effects. The macro-characteristics of the cut surface, such as its taper, trailback, and waviness, are discussed, along with methods of improving the geometrical accuracy of the cut parts using these attributes. For example, dynamic angular compensation is used to correct for the taper and undercut in shape cutting. The surface finish is controlled by the cutting speed, hydraulic, and abrasive parameters using software and process models built into the controllers of CNC machines. In addition to shape cutting, edge trimming is presented, with a focus on the carbon fiber composites used in aircraft and automotive structures, where special AWJ tools and manipulators are used. Examples of the precision cutting of microelectronic and solar cell parts are discussed to describe the special techniques that are used, such as machine vision and vacuum-assist, which have been found to be essential to the integrity and accuracy of cut parts. The use of the AWJ machining process was extended to other applications, such as drilling, boring, milling, turning, and surface modification, which are presented in this paper as actual industrial applications. To demonstrate the versatility of the AWJ machining process, the data in this paper were selected to cover a wide range of materials, such as metal, glass, composites, and ceramics, and also a wide range of thicknesses, from 1 mm to 600 mm. The trends of Industry 4.0 and 5.0, AI, and IoT are also presented.
RESUMEN
The most common aesthetic issue that affects people's smiles is gingival pigmentation, especially in those with high smile lines. This pigmented gingiva is thought to be naturally occurring melanin pigments that add to the gingiva's endogenous pigmentation. The goal of plastic periodontal surgery known as "gingival depigmentation" is to lighten the dark gingiva by scraping off the gingival epithelium. Gingival depigmentation has been performed with a variety of techniques, including bur abrasion, scraping, partial thickness flap, cryotherapy, electrocautery, and laser. The present case comprised a split-mouth design in which depigmentation using an electrosurgical unit and soft tissue trimming bur was used for the maxillary sections, and evaluated the difference in pain felt by the patient and healing of the surgical site between the sites treated with the electrosurgical unit and bur abrasion method. A visual analog scale (VAS) was used to quantify pain felt by the patient on the seventh day, whereas healing was assessed on the seventh day and at a one-month interval visually. The results of this study showed that the electrocautery-treated site showed better results in terms of pain experienced by the patient and also with the surgical site healing.
RESUMEN
BACKGROUND: Digital dermatitis (DD) is a contagious bovine foot disease causing reduced animal welfare and negative economic consequences for the farmer. Treponema spp. are the most important causative agents. Studies indicate that trimming equipment can transfer DD-associated treponemes between cows. The aim of this observational study in 22 DD-positive Norwegian dairy herds was to investigate the risk of transferring Treponema spp. with trimming equipment and chutes after claw trimming, and after washing and disinfection. Swabs from the trimming equipment and chutes were collected from nine different locations, at five different time points. Bacterial DNA was extracted from 647 swabs and analysed by qPCR for Treponema spp. In addition, 172 swabs taken immediately after trimming, were analysed by a multiplex qPCR targeting T. phagedenis, T. pedis and T. medium/vincentii. Biopsy sampling from DD lesions was performed on cows in the same herds during trimming. Altogether 109 biopsies were analysed by FISH for confirmation of the DD diagnosis and identification of Treponema phylotypes (PTs). RESULTS: High numbers of Treponema spp. were detected from all nine locations on the trimming equipment and chutes immediately after trimming, and T. phagedenis was detected on two or more locations in all but two herds, 1 and 19. There was a decline in the amount of Treponema spp. after washing and disinfection. The belly belt, the cuff, and the footrest on the chute had the highest proportion of positive samples after disinfection. The belly belt had the highest copy numbers of all nine locations (median = 7.9, max = 545.1). No Treponema spp. was detected on the hoof knives after disinfection. Treponema phagedenis, T. pedis, and Treponema phylotype 3 (T. refringens) were detected by FISH analysis of the biopsies. Treponema phagedenis was detected in biopsies from all herds except 1 and 19. CONCLUSION: This study shows that DD-associated Treponema spp. were present on the trimming equipment and chutes after trimming cows in DD-positive herds. Washing and disinfection reduced the load of Treponema spp. However, large differences in Treponema spp. between different locations were documented. High copy numbers on the grinder and the chute after disinfection, indicates that sufficient cleaning and disinfection of these locations is difficult, and that passive transfer of DD-associated treponemes (viable or not) is possible.
Asunto(s)
Enfermedades de los Bovinos , Dermatitis Digital , Desinfección , Treponema , Infecciones por Treponema , Animales , Bovinos , Treponema/aislamiento & purificación , Dermatitis Digital/microbiología , Infecciones por Treponema/veterinaria , Infecciones por Treponema/microbiología , Enfermedades de los Bovinos/microbiología , Desinfección/métodos , Femenino , Noruega , Pezuñas y Garras/microbiología , ADN Bacteriano/análisis , Crianza de Animales Domésticos/métodos , Crianza de Animales Domésticos/instrumentaciónRESUMEN
The aim of this study was to evaluate the effect of hoof trimming on overall limb movements by comparing the changes in 8 limb joint angles before and after one week of hoof trimming. Seventeen Holstein-Friesian dairy cows that were able to move freely and had no history of hoof diseases were included in the study. The cows were walked on a rubber mat with a high friction coefficient (HFM) and a low friction coefficient by the spraying of sodium polyacrylate (LFM). A high-speed camera was set to 200 fps on the image analysis software, and the images of the cows that were given 15 reflective markers on their right side were captured while walking on the test mat. The tests were conducted before and after one week of hoof trimming, and the cows were trimmed by the functional hoof trimming method. With image analysis software, video clips of walking cows were confirmed visually and tracked during one gait cycle by each reflective marker attached to the hoof of the forelimb and hindlimb, after which the stance phase and swing phase were identified. The durations of the stance phase and swing phase of the forelimb and hindlimb, respectively, and the maximum, minimum, and range of motion (ROM) values of the 8 joint angles, shoulder joint, elbow joint, carpus joint, forelimb fetlock joint, hip joint, stifle joint, hock joint and hindlimb fetlock joint during one gait cycle were included in the analysis. The maximum and minimum angles of the hip and stifle joints were narrower after hoof trimming than before, although the ROM did not change and was clearer for HFM than for LFM. It was thought that the flexion of the proximal hindlimb would progress smoothly during walking after trimming.
RESUMEN
Lameness, mostly resulting from claw lesions, causes major welfare problems in the dairy industry. One way to prevent claw lesions is hoof trimming, but the overall effect and the optimal hoof trimming frequency are unknown. In a retrospective cohort study, we investigated the association between hoof trimming frequency in primiparous cows and hoof health and culling in second lactation. We based our analysis on breed, calving and culling data in the period 2015-2018 for 30,613 primiparous cows in 202 Swedish dairy herds. Of the cows enrolled, 20% were not hoof-trimmed, 30% were trimmed once, 34% were trimmed twice, 13% were trimmed 3 times, and 2% were trimmed ≥ 4 times. We used multivariable mixed-effect logistic and multivariable multinomial logistic regression models to investigate the association between trimming frequency and 2 outcomes: hoof lesions at first trimming occasion within 90 d from second calving and culling in second lactation within 300 d after second calving. In general, cows trimmed 2 or 3 times during first lactation were at lower odds of having claw lesions compared with cows that were not trimmed (Odds Ratio (OR) = 0.66, 95% CI = 0.62-0.71 and 0.60, 95% CI = 0.55-0.66, respectively) or cows trimmed once (OR = 0.80, 95% CI = 0.75-0.85 and OR = 0.72, 95% CI = 0.66-0.79, respectively), and this beneficial effect was observed for most types of claw lesions. Moreover, cows trimmed 2, 3, or ≥ 4 times were at lower odds of being culled compared with cows that were not trimmed (OR = 0.71, 95% CI = 0.65-0.77, 0.68, 95% CI = 0.61-0.76 and 0.70, 95% CI = 0.54-0.90, respectively) or trimmed once (OR = 0.77, 95% CI = 0.71-0.83, OR = 0.74, 95% CI = 0.66-0.82 and OR = 0.75, 95% CI = 0.59-0.97, respectively). In particular, 2 trimmings, compared with 1 or no trimming, lowered the relative risk-ratio of dying or being euthanized on-farm, or being culled due to claw and leg disorders. More than 1 hoof trimming in first lactation also reduced the relative-risk ratio of being culled for other reasons. In conclusion, 2 or 3 hoof trimmings during first lactation were generally beneficial for hoof health in early second lactation and survival in second lactation. These findings can help improve animal welfare and production by reducing claw lesions, and thereby lameness among dairy cows, which would increase the longevity of dairy cows and the sustainability of the dairy industry.
RESUMEN
The control of digital dermatitis (DD) among cattle is crucial; however, effective and environmentally-sound control measures have yet to be identified. From the monitoring data of DD which were recorded during regular hoof trimmings in a farm in Hokkaido, Japan, we detected a decrease in the DD prevalence in a herd where an anaerobic bacterial fermentation enhancer (ABFE) was distributed. The possible effect of ABFE was analyzed using a retrospective repeated cross-sectional design. The prevalence of DD decreased over time in the ABFE-distributed group. Furthermore, a selected regression model indicated the time-dependent enhancement of the decreasing trend. While potential coincidental factors may influence, this study provides a basis for further research on the preventive effect of ABFE against DD.
Asunto(s)
Enfermedades de los Bovinos , Dermatitis Digital , Fermentación , Animales , Bovinos , Estudios Retrospectivos , Dermatitis Digital/microbiología , Dermatitis Digital/prevención & control , Enfermedades de los Bovinos/microbiología , Enfermedades de los Bovinos/prevención & control , Japón , Estudios Transversales , Bacterias Anaerobias , Pezuñas y Garras/microbiologíaRESUMEN
Correlative Light Electron Microscopy (CLEM) encompasses a wide range of experimental approaches with different degrees of complexity and technical challenges where the attributes of both light and electron microscopy are combined in a single experiment. Although the biological question always determines what technology is the most appropriate, we generally set out to apply the simplest workflow possible. For 2D cell cultures expressing fluorescently tagged molecules, we report on a simple and very powerful CLEM approach by using gridded finder imaging dishes. We first determine the gross localization of the fluorescence using light microscopy and subsequently we retrace the origin/localization of the fluorescence by projecting it onto the ultrastructural reference space obtained by transmission electron microscopy (TEM). Here we describe this workflow and highlight some basic principles of the sample preparation for such a simple CLEM experiment. We will specifically focus on the steps following the resin embedding for TEM and the introduction of the sample in the electron microscope.
Asunto(s)
Flujo de Trabajo , Humanos , Microscopía Fluorescente/métodos , Microscopía Electrónica de Transmisión/métodos , Microscopía Electrónica/métodos , AnimalesRESUMEN
A tool for precise, target-specific, efficient and affordable genome editing, it is a dream for many researchers, from those who do basic research to those who use it for applied research. Since 2012, we have the tool that almost fulfils such requirements; it is based on CRISPR/Cas systems. However, even CRISPR/Cas has limitations and obstacles that might surprise its users. In this review, we focus on the most frequently used variant, CRISPR/Cas9 from Streptococcus pyogenes, and highlight the key factors affecting its mutagenesis outcomes. Firstly, factors affecting the CRISPR/Cas9 activity, such as the effect of the target sequence, chromatin state or Cas9 variant, and how long it remains in place after cleavage. Secondly, factors affecting the follow-up DNA repair mechanisms include mostly the cell type and cell cycle phase, but also, for example, the type of DNA ends produced by Cas9 cleavage (blunt/staggered). Moreover, we note some differences between using CRISPR/Cas9 in plants, yeasts and animals, as knowledge from individual kingdoms is not fully transferable. Awareness of these factors can increase the likelihood of achieving the expected results of plant genome editing, for which we provide detailed guidelines.
RESUMEN
Planar silicon nanowires (SiNWs), grown by using low temperature catalytic approaches, are excellent 1D channel materials for developing high-performance logics and sensors. However, a deterministic position and size control of the metallic catalyst droplets, that lead to the growth of SiNWs, remains still a significant challenge for reliable device integration. In this work, we present a convenient but powerful edge-trimming catalyst formation strategy, which can help to produce a rather uniform single-row of indium (In) catalyst droplets of Dcat = 67 ± 5 nm in diameter, with an exact one-droplet-on-one-step arrangement. This approach marks a significant achievement in self-assembled catalyst formation and offers a foundation to attain a reliable and scalable growth of density SiNW channels, via an in-plane solid-liquid-solid (IPSLS) mechanism, with a uniform diameter down to Dnw = 35 ± 4 nm, and do not rely on high-precision lithography techniques. Prototype SiNW-based field effect transistors (FETs) are also fabricated, with a high Ion/Ioff current ratio and small subthreshold swing of >107 and 262 mV·dec-1, respectively, indicating a reliable new routine to integrate a wide range of SiNW-based logic, sensor, and display applications.
RESUMEN
Tillering/branching pattern plays a significant role in determining the structure and diversity of grass, and trimming has been found to induce tillering in turfgrass. Recently, it has been reported that hydrogen peroxide (H2O2) regulates axillary bud development. However, the role of H2O2 in trimming-induced tillering in bermudagrass, a kind of turfgrass, remains unclear. Our study unveils the significant impact of trimming on promoting the sprouting and growth of tiller buds in stolon nodes, along with an increase in the number of tillers in the main stem. This effect is accompanied by spatial-temporal changes in cytokinin and sucrose content, as well as relevant gene expression in axillary buds. In addition, the partial trimming of new-born tillers results in an increase in sucrose and starch reserves in their leaves, which can be attributed to the enhanced photosynthesis capacity. Importantly, trimming promotes a rapid H2O2 burst in the leaves of new-born tillers and axillary stolon buds. Furthermore, exogenous application of H2O2 significantly increases the number of tillers after trimming by affecting the expression of cytokinin-related genes, bolstering photosynthesis potential, energy reserves and antioxidant enzyme activity. Taken together, these results indicate that both endogenous production and exogenous addition of H2O2 enhance the inductive effects of trimming on the tillering process in bermudagrass, thus helping boost energy supply and maintain the redox state in newly formed tillers.
Asunto(s)
Cynodon , Peróxido de Hidrógeno , Oxidación-Reducción , Antioxidantes , Citocininas , SacarosaRESUMEN
Alzheimer's disease (AD) is the leading cause of dementia and is characterized by a presence of amyloid plaques, composed mostly of the amyloid-ß (Aß) peptides, in the brains of AD patients. The peptides are generated from the amyloid precursor protein (APP), which undergoes a sequence of cleavages, referred as trimming, performed by γ-secretase. Here, we investigated conformational changes in a series of ß-amyloid substrates (from less and more amyloidogenic pathways) in the active site of presenilin-1, the catalytic subunit of γ-secretase. The substrates are trimmed every three residues, finally leading to Aß40 and Aß42, which are the major components of amyloid plaques. To study conformational changes, we employed all-atom molecular dynamics simulations, while for unfolding, we used steered molecular dynamics simulations in an implicit membrane-water environment to accelerate changes. We have found substantial differences in the flexibility of extended C-terminal parts between more and less amyloidogenic pathway substrates. We also propose that the positively charged residues of presenilin-1 may facilitate the stretching and unfolding of substrates. The calculated forces and work/energy of pulling were exceptionally high for Aß40, indicating why trimming of this substrate is so infrequent.
Asunto(s)
Enfermedad de Alzheimer , Secretasas de la Proteína Precursora del Amiloide , Humanos , Secretasas de la Proteína Precursora del Amiloide/metabolismo , Presenilina-1/metabolismo , Dominio Catalítico , Placa Amiloide , Péptidos beta-Amiloides/metabolismo , Enfermedad de Alzheimer/metabolismoRESUMEN
Pigments such as anthraquinones (AQs) and melanins are antioxidants, protectants, or virulence factors. AQs from the entomopathogenic bacterium Photorhabdus laumondii are produced by a modular type II polyketide synthase system. A key enzyme involved in AQ biosynthesis is PlAntI, which catalyzes the hydrolysis of the bicyclic-intermediate-loaded acyl carrier protein, polyketide trimming, and assembly of the aromatic AQ scaffold. Here, multiple crystal structures of PlAntI in various conformations and with bound substrate surrogates or inhibitors are reported. Structure-based mutagenesis and activity assays provide experimental insights into the three sequential reaction steps to yield the natural product AQ-256. For comparison, a series of ligand-complex structures of two functionally related hydrolases involved in the biosynthesis of 1,8-dihydroxynaphthalene-melanin in pathogenic fungi is determined. These data provide fundamental insights into the mechanism of polyketide trimming that shapes pigments in pro- and eukaryotes.
Asunto(s)
Antraquinonas , Melaninas , Policétidos , Antraquinonas/metabolismo , Policétidos/metabolismo , Melaninas/metabolismo , Sintasas Poliquetidas/metabolismo , Sintasas Poliquetidas/genética , Sintasas Poliquetidas/química , Photorhabdus/metabolismo , Photorhabdus/genética , Naftoles/metabolismo , Naftoles/química , Pigmentos Biológicos/metabolismoRESUMEN
The leather industry poses a significant environmental problem through the extensive discharge of trimming waste, primarily composed of skin matrix rich in proteins. Developing a green approach for utilizing this waste can contribute to the sustainable recovery of proteins, transforming them into valuable bioresources. This study introduces an environmentally friendly and economically viable approach to extract collagen from tannery raw trimming waste using papain enzyme-derived from papaya leaves. The research involved extensive assessments and trials to optimize the enzymatic hydrolysis process. The highest collagen recovery was achieved by hydrolyzing 5 % (w/v) delimed powder with 4 % (w/v) crude papain enzyme from papaya leaf powder, maintaining it at 60 °C for 6 h and at pH 5. Collagen extraction from raw trimming waste using acetic acid was also performed, with the optimized papain enzyme-based hydrolysis process resulting in approximately 91 % yield, while conventional acetic acid method yielded approximately 84 %. To evaluate the performance of the enzymatic hydrolysis process in comparison to acid hydrolysis and hydrothermal hydrolysis, an integrated MW-TOPSIS framework was proposed. This framework determined that enzymatic hydrolysis achieved the highest closeness coefficient value (Ri = 0.40), indicating its superiority as the preferred alternative among the tested methods.
Asunto(s)
Colágeno , Papaína , Polvos , Hidrólisis , AcetatosRESUMEN
PURPOSE: To describe the in toto explantation of the CyPass® Micro-Stent and its conceivable complications. METHODS: This is a case series of eighteen eyes from fourteen patients who underwent CyPass® Micro-Stent implantation due to mild to moderate glaucoma and who subsequently suffered from loss of endothelial cell density. Consequently, the CyPass® Micro-Stent was in toto explanted. The surgical procedure and its complications are described and compared with trimming of the CyPass® Micro-Stent. RESULTS: A postoperative hyphema was developed in 8 of the 18 eyes. In four of them the hyphema was self-limiting, while in two patients an anterior chamber irrigation was necessary. One patient suffered from a severe intracameral bleeding and iridodialysis during explantation, so that the base of the iris had to be scleral fixated. The remaining explantations were without complications. CONCLUSION: Dealing with implanted CyPass® Micro-Stents poses a challenge for ophthalmic surgeons. An in toto removal can be traumatic, since the CyPass stent often is fibrotic encapsulated and fused with the surrounding tissue. Alternatively, trimming of the CyPass is also a viable option to avoid further endothelial damage. Reported complications of CyPass trimming are consistent with those that can occur after explantation. Further data on the development of the endothelial cells after trimming or explantation are not yet available. Therefore, it remains open whether trimming of the CyPass, in contrast to complete removal, carries the risk of further endothelial cell loss.
Asunto(s)
Implantes de Drenaje de Glaucoma , Glaucoma de Ángulo Abierto , Compuestos de Quinolinio , Tiazoles , Humanos , Presión Intraocular , Células Endoteliales , Hipema , Glaucoma de Ángulo Abierto/cirugía , Implantes de Drenaje de Glaucoma/efectos adversos , Cámara Anterior , Stents/efectos adversos , Complicaciones PosoperatoriasRESUMEN
The first aim of this study was to calculate the prevalence of painful lesions of the digits ("alarm" lesions; ALs) in Swiss dairy herds and cow-calf operations over a three-year study period. The following ALs were included in the calculation: the M2 stage of digital dermatitis (DD M2), ulcers (U), white line fissures (WLF) of moderate and high severity, white line abscesses (WLA), interdigital phlegmon (IP) and swelling of the coronet and/or bulb (SW). Between February 2020 and February 2023, digit disorders were electronically recorded during routine trimmings by 40 specially trained hoof trimmers on Swiss cattle farms participating in the national claw health programme. The data set used consisted of over 35,000 observations from almost 25,000 cows from 702 herds. While at the herd-level, the predominant AL documented in 2022 was U with 50.3% followed by WLF with 38.1%, at the cow-level, in 2022, it was DD M2 with 5.4% followed by U with 3.7%. During the study period, within-herd prevalences of ALs ranged from 0.0% to a maximum of 66.1% in 2020. The second aim of this study was to determine herd- and cow-level risk factors associated with digital dermatitis (DD), U and white line disease (WL) in dairy cows using data from 2022. While for DD, analysed herd-level factors appeared to have a greater effect on the probability of its occurrence, the presence of U and WL was mainly associated with the analysed cow-level factors. The risk for DD increased with a higher herd trimming frequency. Herds kept in tie stalls had a lower risk for DD and WL and a higher risk for U compared to herds kept in loose housing systems. Herds with predominantly Holstein Friesian cows as well as Holstein Friesian cows had a higher risk for the occurrence of DD compared to herds and cows of other breeds. With increasing parity, cows had a higher risk of developing U and WL, whereas for DD, parity was negatively associated with prevalence. Cows trimmed during the grazing period had a higher risk of U and WL than cows trimmed during the housing period. These findings may contribute to improve management measures affecting the health of the digits in farms with structures similar to those evaluated in the current study, such as small herds with frequent access to pasture. Further research is warranted to demonstrate how measures addressing the current results combined with those of individual herd risk assessments might contribute to an improvement in the health of the digits in the respective dairy herds.
RESUMEN
BACKGROUND: Lameness has been associated with compromised animal welfare and reduced productivity in dairy cattle herds worldwide. However, little is known about the prevalence of claw lesions in the dairy buffalo population in Egypt. Furthermore, the optimum measurements for claw trimming in buffalo are unknown. A cross-sectional cadaver study was conducted where 135 pair buffalo hind feet were collected from 4 slaughterhouses and examined for the presence of claw lesions. The proportion and associated 95% confidence interval (CI) of each type of lesion were calculated. A separate set of healthy claws (n = 26) underwent ultrasonography (US) and computed tomography (CT). The agreement between US and CT measurements was assessed using Passing-Bablok regression and intraclass correlation coefficient. The CT measurements were used to calculate trimming recommendations. RESULTS: At least one lesion was identified in 242 claws (89.6%, 95% CI = 85.4-93.0). In healthy claws, poor to moderate agreement was identified between US and CT measurements which could be due a sample size of the study. The average ± standard deviation (SD) minimum recommended external wall length of the lateral and medial claws in heifers was 7.1 ± 0.36 cm and 7.5 ± 0.35 cm, respectively. The average ± SD minimum recommended external wall length in buffaloes over five years of age was 8.2 ± 0.27 cm and 8.4 ± 0.39 cm for the lateral and medial claws, respectively. CONCLUSIONS: The study found a high prevalence of claw lesions in buffalo in Egypt, the clinical significance of which requires further elucidation. Recommended measurements will help guide claw trimming in buffalo to minimise lesions.
Asunto(s)
Bison , Enfermedades de los Bovinos , Enfermedades del Pie , Pezuñas y Garras , Animales , Femenino , Bovinos , Enfermedades del Pie/diagnóstico por imagen , Enfermedades del Pie/epidemiología , Enfermedades del Pie/veterinaria , Búfalos , Mataderos , Prevalencia , Estudios Transversales , Egipto/epidemiología , Pezuñas y Garras/diagnóstico por imagen , Pezuñas y Garras/patología , Crianza de Animales Domésticos/métodos , Enfermedades de los Bovinos/diagnóstico por imagen , Enfermedades de los Bovinos/epidemiología , Enfermedades de los Bovinos/patología , Cojera Animal/epidemiologíaRESUMEN
Lameness in bulls is a common problem seen by many veterinarians, and the cause can be difficult to determine. Understanding cattle lameness requires experience and complete knowledge of their structural anatomy and handling. This article reviews the common body regions that cause lameness in bulls and discusses their treatment. It also details hoof trimming as a way to manage lameness.