Defect-Engineered MOF-801/Sodium Alginate Aerogel Beads for Boosting Adsorption of Pb(II).

Metal-organic frameworks (MOFs) are attractive adsorbents for heavy metal capture due to their superior stability, easy modification, and adjustable pore size. However, their inherent microporous structure poses challenges in achieving a higher adsorption capacity. Defect engineering is considered a simple method to create hierarchical MOFs with larger pores. Here, we employed l-aspartic acid as a mixed linker to bind Zr4+ clusters in competition with fumaric acid of MOF-801 to create defects, and the pore size was increased from 4.66 to 15.65 nm. Mercaptosuccinic acid was subsequently used as a postexchange ligand to graft the resultant MOF-801 by acid-ammonia condensation to further expand the pore size to 22.73 nm. Notably, the -NH2, -COOH, and -SH groups contributed by these two ligands increased the adsorption sites for Pb(II). The obtained defective MOF-801 with larger pores was thereafter loaded onto sodium alginate to form aerogel beads as adsorbents, and an adsorption capacity of 375.48 mg/g for Pb(II) was achieved, which is ∼51 times that of pristine MOF-801. The aerogel beads also exhibited outstanding reusability with a removal efficiency of ∼90.23% after 5 cycles of use. The adsorption mechanism of Pb(II) included ion-exchange interaction, as well as chelation interactions of Pb-O, Pb-NH2, and Pb-S. The versatile combination of defect engineering and composite beads provides novel inspirations for MOF modification for boosting heavy metal adsorption.

Mixed-Linker Strategy for the Construction of Sulfone-Containing D-A-A Covalent Organic Frameworks for Efficient Photocatalytic Hydrogen Peroxide Production.

The solar-driven photocatalytic production of hydrogen peroxide (H2O2) from water and oxygen using semiconductor catalysts offers a promising approach for converting solar energy into storable chemical energy. However, the efficiency of photocatalytic H2O2 production is often restricted by the low photo-generated charge separation, slow surface reactions and inadequate stability. Here, we developed a mixed-linker strategy to build a donor-acceptor-acceptor (D-A-A) type covalent organic framework (COF) photocatalyst, FS-OHOMe-COF. The FS-OHOMe-COF structure features extended π-π conjugation that improves charge mobility, while the introduction of sulfone units not only as active sites facilitates surface reactions with water but also bolsters stability through increased interlayer forces. The resulting FS-OHOMe-COF has a low exciton binding energy, long excited-state lifetime and high photo-stability that leads to high performance for photocatalytic H2O2 production (up to 1.0 mM h-1) with an H2O2 output of 19 mM after 72 hours of irradiation. Furthermore, the catalyst demonstrates high stability, which sustained activity over 192 hours of photocatalytic experiment.

Regulating highly photoelectrochemical activity of Zr-based mixed-linker metal-organic frameworks toward sensitive electrogenerated chemiluminescence sensing of α-glucosidase.

The conductivity and emission efficiency of metal-organic frameworks (MOFs) remain challenging factors that limit their electrogenerated chemiluminescence (ECL) sensing applications. Herein, we report a facile approach to address these challenges by integrating an electroactive linker (H2-TCPP) with an ECL active electrogenerated chemiluminescence linker (H4-TBAPy) to construct a highly photoelectrochemical active mixed-linker MOFs (ML-MOFs). ECL results revealed a remarkable 15.4-fold enhancement for the top-performing ML-MOFs (M6-MOFs), surpassing the single linker MOFs. In addition, M6-MOFs also exhibit a remarkable 73-fold enhancement in ECL efficiency compared to commercial Ru (bpy)32+. This improvement should be attributed to the synergistic effects resulting from the combination of two linkers. Furthermore, M6-MOFs are found to be served as a model ECLphore for sensitive and selective detection of α-glucosidase for the first time with good potential practicability in human serum samples. This work represents a promising direction to guide for designing good conductivity and high ECL efficiency MOFs in terms of linker functionalization and thus bandgap modulation for advancing their ECL sensing applications.

Redox-Active Mixed-Linker Metal-Organic Frameworks with Switchable Semiconductive Characteristics for Tailorable Chemiresistive Sensing.

Metal-organic frameworks (MOFs), with diverse metal nodes and designable organic linkers, offer unique opportunities for the rational engineering of semiconducting properties. In this work, we report a mixed-linker conductive MOF system with both tetrathiafulvalene and Ni-bis(dithiolene) moieties, which allows the fine-tuning of electronic structures and semiconductive characteristics. By continuously increasing the molar ratio between tetrathiafulvalene and Ni-bis(dithiolene), the switching of the semiconducting behaviors from n-type to p-type was observed along with an increase in electrical conductivity by 3 orders of magnitude (from 2.88×10-7  S m-1 to 9.26×10-5  S m-1 ). Furthermore, mixed-linker MOFs were applied for the chemiresistive detection of volatile organic compounds (VOCs), where the sensing performance was modulated by the corresponding linker ratios, showing synergistic and nonlinear modulation effects.

Hydrolytically stable mixed ditopic linker based zirconium metal organic framework as a robust photocatalyst towards Tetracycline Hydrochloride degradation and hydrogen evolution.

In the existing eco-crisis, designing and engineering an efficient as well as water stable photocatalyst for energy conversion and pollutant abatement remains crucial. In this regard, a mixed linker type zirconium metal organic framework (Zr-MOF) with terepthalic acid based ditopic linkers were utilized to design a single component photocatalyst through single step solvothermal method to utilize photons from visible light illumination towards hydrogen energy (H2) production and Tetracycline Hydrochloride (TCH) degradation. The one pot synthesized mixed linker based Zr-MOF displays visible light absorption through band gap tuning, superior exciton segregation and oxygen vacancy that cumulatively supports the enhancement in the photocatalytic output with respect to their pristine counterparts. Additionally, the X-ray photoelectron spectroscopy, optical and electrochemical studies strongly reinforces the above claims. The prepared mixed linker Zr-MOF showed superior photocatalytic H2 evolution performance of 247.88 µmol h-1 (apparent conversion efficiency; ACE = 1.9%) that is twice than its pristine Zr-MOFs. Moreover, in TCH degradation, the mixed linker MOF displays an enhanced efficacy of 91.8 % and adopts pseudo-first order type kinetics with a rate constant value of 0.032. Typically, the active species participating for the TCH photo-degradation follows the order of hydroxyl (OH.) < superoxide (O2.-) radicals. Consequently, the mixed linker Zr-MOF could be effectively used as a robust photocatalyst exhibiting boosted TCH degradation and H2 production.

Imparting Multifunctionality in Zr-MOFs Using the One-Pot Mixed-Linker Strategy: The Effect of Linker Environment and Enhanced Pollutant Removal.

The development of mixed-linker metal-organic frameworks (MOFs) is an efficient strategy to improve the performance of MOFs. Herein, we successfully integrate tetrakis(4-carboxyphenyl)porphyrin (TCPP) into different Zr-MOFs via a facile one-pot solvothermal synthesis while preserving the integrity of their frameworks. The functional groups, length of primary linkers, and the inner pore structure significantly affected the properties of the synthesized TCPP@MOFs, such as surface area, average pore size, and 1O2 productivity. Among them, TCPP@PCN-777 demonstrated the largest surface area (2386 cm2/g, as measured by N2 uptake) and the highest 1O2 generation rate (1.15 h-1, [1O2]ss = 2.66 × 10-12 M) under irradiation. The TCPP loading was also shown to affect the crystal phase, morphology, surface area, and photochemical properties of the synthesized MOFs. Therefore, TCPP@PCN-777s with various TCPP loadings were synthesized to investigate the optimum loading. The optimized TCPP@MOF, TCPP@PCN-777-30, was evaluated for its removal of model contaminant ranitidine (RND) through both adsorption and photodegradation. TCPP@PCN-777-30 showed a higher adsorption capacity toward RND than both the parent MOF (PCN-777) and commercially available activated carbon, and effectively degraded RND in aqueous solution (>99% photodegradation in 1 h). With irradiation, TCPP@PCN-777-30 showed a minimal loss in adsorption efficiency over four consecutive treatment cycles, confirming the reusability of the material enabled through the incorporation of TCPP into the MOF structure. This work not only developed an efficient multifunctional material for environmental remediation but also forwarded knowledge on the effect of linker environment (i.e., functional groups, framework structure, and linker ratio) on the properties of TCPP@MOFs to guide future research on mixed-linker MOFs.

Covalent Triazine Frameworks Based on the First Pseudo-Octahedral Hexanitrile Monomer via Nitrile Trimerization: Synthesis, Porosity, and CO2 Gas Sorption Properties.

Herein, we report the first synthesis of covalent triazine-based frameworks (CTFs) based on a hexanitrile monomer, namely the novel pseudo-octahedral hexanitrile 1,4-bis(tris(4'-cyano-phenyl)methyl)benzene 1 using both ionothermal reaction conditions with ZnCl2 at 400 °C and the milder reaction conditions with the strong Brønsted acid trifluoromethanesulfonic acid (TFMS) at room temperature. Additionally, the hexanitrile was combined with different di-, tri-, and tetranitriles as a second linker based on recent work of mixed-linker CTFs, which showed enhanced carbon dioxide captures. The obtained framework structures were characterized via infrared (IR) spectroscopy, elemental analysis, scanning electron microscopy (SEM), and gas sorption measurements. Nitrogen adsorption measurements were performed at 77 K to determine the Brunauer-Emmett-Teller (BET) surface areas range from 493 m2/g to 1728 m2/g (p/p0 = 0.01-0.05). As expected, the framework CTF-hex6 synthesized from 1 with ZnCl2 possesses the highest surface area for nitrogen adsorption. On the other hand, the mixed framework structure CTF-hex4 formed from the hexanitrile 1 and 1,3,5 tricyanobenzene (4) shows the highest uptake of carbon dioxide and methane of 76.4 cm3/g and 26.6 cm3/g, respectively, at 273 K.

Facile Strategy for Efficient Charge Separation and High Photoactivity of Mixed-Linker MOFs.

Two new sets of UiO-Zr metal-organic framework (MOF) bearing mixed linkers BDC-(SCH3)2 and BDC-(SOCH3)2 that have different band gaps and edges were prepared through post oxidation and direct methods, namely, UiO-66-(SCH3)2-xh (x = 4, 9, 12 oxidation hours) and UiO-66-(SOCH3)x(SCH3)2-x (x = 0, 0.4, 0.6, 2), respectively. These composites with stoichiometric components were fully characterized via proton nuclear magnetic resonance (1H NMR) spectroscopy, powder X-ray diffraction (PXRD), transmission electron microscopy (TEM), Fourier-transform infrared (FT-IR) spectra, Brunauer-Emmett-Teller (BET), photo electrochemical measurements, and femtosecond transient absorption (fs-TA) spectroscopy. The structure, electronic property, and photoresponsive and catalytic ability as the functions of the molar ratio of linkers and the synthetic protocol were first investigated. The mixed-linker UiO-66-(SCH3)2-xh and UiO-66-(SOCH3)x(SCH3)2-x exhibited improved performances as compared to the UiO-66-(SCH3)2 and UiO-66-(SOCH3)2 possessing neat linkers only. Their photo response and catalytic activity varied with different linker ratios. For UiO-66-(SCH3)2-xh, the performance increased with the increasing linker BDC-(SOCH3)2 ratio upon oxidation but reached the highest as the BDC-(SOCH3)2 being of 24.4% in UiO-66-(SCH3)2-9h. In comparison, the best photocurrent (80.74 uA/cm-2) and the highest H2 generation rate (2018.8 µmol g-1 h-1) (λ > 400 nm) in UiO-66-(SCH3)2-9h are about twice those of UiO-66-(SOCH3)0.4(SCH3)1.6 obtained by direct synthesis, although the linker BDC-(SOCH3)2 ratio of those two composites is almost the same (24.4% vs 23.9%). Recorded shorter lifetime and higher charge separation efficiency of the former than those of the latter suggest the postsynthetic protocol as the efficient method for achieving the mixed-liner-MOF-based photocatalyst with high performance. A new type-II tailored homojunction is proposed in these mixed-linker MOFs for their efficient charge separation and improved activity.

Increasing the Complexity in the MIL-53 Structure: The Combination of the Mixed-Metal and the Mixed-Linker Concepts.

The isoreticular mixed-component concept is a promising approach to tailor the material properties of metal-organic frameworks. While isoreticular mixed-metal or mixed-linker materials are commonly synthesized, the combination of both concepts for the development of isoreticular materials featuring both two metals and two linkers is still rarely investigated. Herein, we present the development of mixed-metal/mixed-linker MIL-53 materials that contain different metal combinations (Al/Sc, Al/V, Al/Cr, Al/Fe) and different linker ratios (terephthalate/2-aminoterephthalate). The possibility of changing the metal combination and the linker ratio independently from each other enables a large variety of modifications. A thorough characterization (PXRD, ATR-IR, TGA, 1 H NMR, ICP-OES) confirmed that all components were incorporated into the framework structure with a statistical distribution. Nitrogen physisorption measurements showed that the breathing behavior can be tailored by adjusting the linker ratio for all metal combinations. All materials were successfully used for post-synthetic modification reactions with maleic anhydride.

Defect Engineering of Copper Paddlewheel-Based Metal-Organic Frameworks of Type NOTT-100: Implementing Truncated Linkers and Its Effect on Catalytic Properties.

A series of new defect-engineered metal-organic frameworks (DEMOFs) were synthesized by framework doping with truncated linkers employing the mixed-linker approach. Two tritopic defective (truncated) linkers, biphenyl-3,3',5-tricarboxylates (LH) lacking a ligating group and 5-(5-carboxypyridin-3-yl)isophthalates (LPy) bearing a weaker interacting ligator site, were integrated into the framework of Cu2(BPTC) (NOTT-100, BPTC = biphenyl-3,3',5,5'-tetracarboxylates). Incorporating LH into the framework mainly generates missing metal node defects, thereby obtaining dangling COOH groups in the framework. However, introducing LPy forms more modified metal nodes featuring reduced and more accessible Cu sites. In comparison with the pristine NOTT-100, the defect-engineered NOTT-100 (DE-NOTT-100) samples show two unique features: (i) functional groups (the protonated carboxylate groups as the Brønsted acid sites or the pyridyl N atoms as the Lewis basic sites), which can act as second active sites, are incorporated into the MOF frameworks, and (ii) more modified paddlewheels, which provided extra coordinatively unsaturated sites, are generated. The cooperative functioning of the above characteristics enhances the catalytic performance of certain types of reactions. For a proof of concept, two exemplary reactions, namely, the cycloaddition of CO2 with propylene oxide to propylene carbonate and the cyclopropanation of styrene, were carried out to evaluate the catalytic activities of those DE-NOTT-100 materials depending on the defect structure.

Applications of Dynamic Covalent Chemistry Concept towards Tailored Covalent Organic Framework Nanomaterials: A Review.

Covalent organic frameworks (COFs) are a rapidly developing class of materials that has been of immense research interest during the last ten years. Numerous reviews have been devoted to summarizing the synthesis and applications of COFs. However, the underlying dynamic covalent chemistry (DCC), which is the foundation of COFs synthesis, has never been systematically reviewed in this context. Dynamic covalent chemistry is the practice of using thermodynamic equilibriums to molecular assemblies. This Critical Review will cover the state-of-the-art use of DCC to both synthesize COFs and expand the applications of COFs. Five synthetic strategies for COF synthesis are rationalized, namely: modulation, mixed linker/linkage, sub-stoichiometric reaction, framework isomerism, and linker exchange, which highlight the dynamic covalent chemistry to regulate the growth and to modify the properties of COFs. Furthermore, the challenges in these approaches and potential future perspectives in the field of COF chemistry are also provided.

Vapor-Phase Linker Exchange of the Metal-Organic Framework ZIF-8: A Solvent-Free Approach to Post-synthetic Modification.

Zeolitic imidazolate frameworks (ZIFs) are a sub-class of metal-organic frameworks (MOFs). Although generally stable, ZIFs can undergo post-synthetic linker exchange (PSLE) in solution under mild conditions. Herein, we present a novel, solvent-free approach to post-synthetic linker exchange through exposure to linker vapor.

Ultra-Tuning of the Aperture Size in Stiffened ZIF-8_Cm Frameworks with Mixed-Linker Strategy for Enhanced CO2 /CH4 Separation.

ZIF-8 membrane has the potential for CO2 /CH4 separation based on size exclusion. But if traditionally prepared by solvothermal methods, it shows only negligible selectivity due to the linker mobility. Here, ≈500 nm-thin hybrid ZIF-7x -8 membranes with suppressed linker mobility and narrowed window aperture are prepared by a fast current-driven synthesis (FCDS) within 20 min. The in situ electric field during FCDS allows the formation of stiffened ZIF-8_Cm as parent skeleton and the mixed-linker strategy is applied to narrow the aperture size simultaneously. The ZIF-722 -8 membrane shows significantly sharpened molecular sieving for CO2 /CH4 with a separation factor above 25, which soared tenfold compared with other unmodified ZIF-8 membranes. Additionally, the membrane shows exceptional separation performance for H2 /CH4 and CO2 /N2 , with separation factors of 71 and 20, respectively. After 180 h temperature swing operation, it still maintains the excellent separation performance.

Synthetic Strategies and Structural Arrangements of Isoreticular Mixed-Component Metal-Organic Frameworks.

In recent years, the synthesis of mixed-metal and mixed-linker metal-organic frameworks with multiple metals and/or linker molecules combined in one framework has become a growing field of interest. These mixed-component or multivariate metal-organic framework materials provide the possibility to introduce multiple functionalities inside one framework. The interaction of guest molecules with different functionalities in the same material is a promising approach in the fields of gas storage, separation, catalysis and drug delivery. Furthermore, the combination of different components may lead to synergistic effects that cannot be achieved otherwise. These mixed-component approaches open up new pathways to an even larger range of possible customizations in the field of metal-organic frameworks.

Effect of Redox "Non-Innocent" Linker on the Catalytic Activity of Copper-Catecholate-Decorated Metal-Organic Frameworks.

Two new UiO-68 type of Zr-MOFs featuring redox non-innocent catechol-based linkers of different redox activities have been synthesized through a de novo mixed-linker strategy. Metalation of the MOFs with Cu(II) precursors triggers the reduction of Cu(II) by the phenyl-catechol groups to Cu(I) with the concomitant formation of semiquinone radicals as evidenced by EPR and XPS characterization. The MOF-supported catalysts are selective toward the allylic oxidation of cyclohexene and it is found that the presence of in situ-generated Cu(I) species exhibits enhanced catalytic activity as compared to a similar MOF with Cu(II) metalated naphthalenyl-dihydroxy groups. This work unveils the importance of metal-support redox interactions in the catalytic activity of MOF-supported catalysts which are not easily accessible in traditional metal oxide supports.