Mechanism-guided Rational Design of Anode Coatings for Aqueous Zinc Ion Batteries.

Aqueous zinc ion batteries (ZIBs) hold promises as a safer, more cost-effective, and environmental-friendly alternative to lithium-ion batteries, especially for stationary energy storage. Recent advancements in protective anode coatings, which fine-tune zinc ion solvation structure, have yielded significant improvements in the aqueous ZIB performance, addressing dendrite formation and side reactions, thereby prolonging cycle lifetime. Understanding the underlying mechanisms of these coatings as ions sieves is crucial for further optimization and achieving long-term stability, which is a key requirement for practical applications. This concept explores recent developments in ZIB anode coatings from the view of molecular mechanisms and points out future research directions.

Highly Reversible and Dendrite-Free Zinc Anodes Enabled by PEDOT Nanowire Interfacial Layers for Aqueous Zinc-Ion Batteries.

The aqueous zinc-ion batteries (ZIBs) have gained increasing attention because of their high specific capacity, low cost, and good safety. However, side reactions, hydrogen evolution reaction, and uncontrolled zinc dendrites accompanying the Zn metal anodes have impeded the applications of ZIBs in grid-scale energy storage. Herein, the poly(3,4-ethylenedioxythiophene) (PEDOT) nanowires as an interfacial layer on the Zn anode (Zn-PEDOT) are reported to address the above issues. Our experimental results and density functional theory simulation reveal that the interactions between the Zn2+ and S atoms in thiophene rings of PEDOT not only facilitate the desolvation of hydrated Zn2+ but also can regulate the diffusion of Zn2+ along the thiophene molecular chains and induce the dendrite-free deposition of Zn along the (002) surface. Consequently, the Zn||Cu-PEDOT half-cell exhibits highly reversible plating/stripping behavior with an average Coulombic efficiency of 99.7% over 2500 cycles at 1 mA cm-2 and a capacity of 0.5 mAh cm-2. A symmetric Zn-PEDOT cell can steadily operate over 1100 h at 1 mA cm-2 (1 mAh cm-2) and 470 h at 10 mA cm-2 (2 mAh cm-2), outperforming the counterpart bare Zn anodes. Besides, a Zn-PEDOT||V2O5 full cell could deliver a specific capacity of 280 mAh g-1 at 1 A g-1 and exhibits a decent cycling stability, which are much superior to the bare Zn||V2O5 cell. Our results demonstrate that PEDOT nanowires are one of the promising interfacial layers for dendrite-free aqueous ZIBs.

Ultrasonication-Boosted Resorcinol-Formaldehyde Resin Nanoparticle Bromine Fixation and Corresponding Upgraded Aquatic Applications.

Bromine (Br2) and related species removal from water systems are rather complicated due to the complicated chemistry instability, and materials with high Br2 removal rate and efficiency, along with stimuli/apparatus suitable for highly corrosive environments, are necessary. Ultrasonication as a non-destructive process is especially suitable in scenarios where conventional stir apparatus is not applicable, such as highly corrosive environments. Considering the validity nature of Br2 and combining the advantages of ultrasonic with a highly stable Br2 fixation method through aromatic polymer nanoparticles, we demonstrate highly efficient acoustic-aided Br2 removal in aqueous solutions with two times capacity compared to the non-treated sample. Related aquatic applications are also proposed for the materials to be cost-effective, including silver (Ag) recovery, recyclable MnO2-mediated Br2 deep removal, and aqueous zinc anode modification. The coupled novel-material-based processes motivate the strategic design of water purification with high-safety and sustainable industrial procedures and post-value-added utilizations.

Simultaneous Inhibition of Vanadium Dissolution and Zinc Dendrites by Mineral-Derived Solid-State Electrolyte for High-Performance Zinc Metal Batteries.

Designing solid electrolyte is deemed as an effective approach to suppress the side reaction of zinc anode and active material dissolution of cathodes in liquid electrolytes for zinc metal batteries (ZMBs). Herein, kaolin is comprehensively investigated as raw material to prepare solid electrolyte (KL-Zn) for ZMBs. As demonstrated, KL-Zn electrolyte is an excellent electronic insulator and zinc ionic conductor, which presents wide voltage window of 2.73 V, high ionic conductivity of 5.08 mS cm-1, and high Zn2+ transference number of 0.79. For the Zn//Zn cells, superior cyclic stability lasting for 2200 h can be achieved at 0.2 mA cm-2. For the Zn//NH4V4O10 batteries, stable capacity of 245.8 mAh g-1 can be maintained at 0.2 A g-1 after 200 cycles along with high retention ratio of 81%, manifesting KL-Zn electrolyte contributes to stabilize the crystal structure of NH4V4O10 cathode. These satisfying performances can be attributed to the enlarged interlayer spacing, zinc (de)solvation-free mechanism and fast diffusion kinetics of KL-Zn electrolyte, availably guaranteeing uniform zinc deposition for zinc anode and reversible zinc (de)intercalation for NH4V4O10 cathode. Additionally, this work also verifies the application possibility of KL-Zn electrolyte for Zn//MnO2 batteries and Zn//I2 batteries, suggesting the universality of mineral-based solid electrolyte.

Co-Regulating Solvation Structure and Hydrogen Bond Network via Bio-Inspired Additive for Highly Reversible Zinc Anode.

The feasibility of aqueous zinc-ion batteries for large-scale energy storage is hindered by the inherent challenges of Zn anode. Drawing inspiration from cellular mechanisms governing metal ion and nutrient transport, erythritol is introduced, a zincophilic additive, into the ZnSO4 electrolyte. This innovation stabilizes the Zn anode via chelation interactions between polysaccharides and Zn2+. Experimental tests in conjunction with theoretical calculation results verified that the erythritol additive can simultaneously regulate the solvation structure of hydrated Zn2+ and reconstruct the hydrogen bond network within the solution environment. Additionally, erythritol molecules preferentially adsorb onto the Zn anode, forming a dynamic protective layer. These modifications significantly mitigate undesirable side reactions, thus enhancing the Zn2+ transport and deposition behavior. Consequently, there is a notable increase in cumulative capacity, reaching 6000 mA h cm⁻2 at a current density of 5 mA cm-2. Specifically, a high average coulombic efficiency of 99.72% and long cycling stability of >500 cycles are obtained at 2 mA cm-2 and 1 mA h cm-2. Furthermore, full batteries comprised of MnO2 cathode and Zn anode in an erythritol-containing electrolyte deliver superior capacity retention. This work provides a strategy to promote the performance of Zn anodes toward practical applications.

Inorganic Electrolyte Additive Promoting the Interfacial Stability for Durable Zn-Ion Batteries.

The development of Zn-ion batteries (ZIBs) is always hindered by the ruleless interface reactions between the solid electrode and liquid electrolyte, and seeking appropriate electrolyte additives is considered as a valid approach to stabilize the electrode/electrolyte interphases for high-performance ZIBs. Benefiting from the unique solubility of TiOSO4 in acidic solution, the composite electrolyte of 2 m ZnSO4+30 mm TiOSO4 (ZSO/TSO) is configured and its positive contribution to Zn//Zn cells, Zn//Cu cells, and Zn//NH4V4O10 batteries are comprehensively investigated by electrochemical tests and theoretical calculations. Based on the theoretical calculations, the introduction of TiOSO4 contributes to facilitating the desolvation kinetics of Zn2+ ions and guarantees the stable interface reactions of both zinc anode and NH4V4O10 cathode. As expected, Zn//Zn cells keep long-term cycling behavior for 3750 h under the test condition of 1 mA cm-2-1 mAh cm-2, Zn//Cu cells deliver high Coulombic efficiency of 99.9% for 1000 cycles under the test condition of 5 mA cm-2-1 mAh cm-2, and Zn//NH4V4O10 batteries maintain reversible specific capacity of 193.8 mAh g-1 after 1700 cycles at 5 A g-1 in ZSO/TSO electrolyte. These satisfactory results manifest that TiOSO4 additive holds great potential to improve the performances of ZIBs.

A Dual Salt/Dual Solvent Electrolyte Enables Ultrahigh Utilization of Zinc Metal Anode for Aqueous Batteries.

Rechargeable aqueous zinc batteries are promising in next-generation sustainable energy storage. However, the low zinc (Zn) metal anode reversibility and utilization in aqueous electrolytes due to Zn corrosion and poor Zn2+ deposition kinetics significantly hinder the development of Zn-ion batteries. Here, a dual salt/dual solvent electrolyte composed of Zn(BF4)2/Zn(Ac)2 in water/TEGDME (tetraethylene glycol dimethyl ether) solvents to achieve reversible Zn anode at an ultrahigh depth of discharge (DOD) is developed. An "inner co-salt and outer co-solvent" synergistic effect in this unique dual salt/dual solvent system is revealed. Experimental results and theoretical calculations provide evidence that the ether co-solvent inhibits water activity by forming hydrogen bonding with the water and coordination effects with the proton in the outer Zn2+ solvation structure. Meanwhile, the anion of zinc acetate co-salt enters the inner Zn2+ solvation structure, thereby accelerating the desolvation kinetics. Strikingly, based on the electrolyte design, the zinc anode shows high reversibility at an ultrahigh utilization of 60% DOD with 99.80% Coulombic efficiency and 9.39 mAh cm-2 high capacity. The results far exceed the performance reported in electrolyte design work recently. The work provides fundamental insights into inner co-salt and outer co-solvent synergistic regulation in multifunctional electrolytes for reversible aqueous metal-ion batteries.

Construction of ultrathin solid electrolyte interface on Zn anode within 1 min for high current operating condition.

Organic acid treatment can facilitate the in-situ formation of a solid electrolyte interface (SEI) on Zn foil protecting the anode from corrosion. However, the generation of hydrogen (H2) during this process is inevitable, which is often considered detrimental to getting compact SEI. Herein, a H2 film-assisted method is proposed under concentrated Amino-Trimethylene-Phosphonic-Acid to construct ultrathin and dense SEI within 1 min. Specifically, the (002) crystal planes survive from the etching process of 1 min due to the adhered H2, inducing uniform deposition and enhanced corrosion-resistance. Moreover, the H2 can effectively regulate the reaction rate, leading to ultrathin SEI and initiating a morphology preservation behavior, which has been neglected by the previous reports. The quick-formed SEI has excellent compatibility, low resistance and effective isolation of electrolyte/anode, whose advantages work together with exposed (002) planes to get accustomed to high-current surge, leading to the ZAC1@Zn//ZAC1@Zn consistently cycling over 800 h at 15 mA cm-2 and 15 mAh cm-2, the ZAC1@Zn//Cu preserves high reversibility (CE 99.7 %), and the ZAC1@Zn//MVO exhibits notable capacity retention at 191.7 mAh/g after 1000 cycles.

Low-Cost Aqueous Electrolyte with MBA Additives for Uniform and Stable Zinc Deposition.

Aqueous zinc ion batteries (AZIBs) are attracting increasing research interest due to their intrinsic safety, low cost, and scalability. However, the issues including hydrogen evolution, interface corrosion, and zinc dendrites at anodes have seriously limited the development of aqueous zinc ion batteries. Here, N,N-methylenebis(acrylamide) (MBA) additives with -CONH- groups are introduced to form hydrogen bonds with water and suppress H2O activity, inhibiting the occurrence of hydrogen evolution and corrosion reactions at the interface. In situ optical microscopy demonstrates that the MBA additive promotes the uniform deposition of Zn2+ and then suppresses the dendrite growth on the zinc anode. Therefore, Zn//Ti asymmetric batteries demonstrate a high plating/stripping efficiency of 99.5%, while Zn//Zn symmetric batteries display an excellent cycle stability for more than 1000 h. The Zn//MnO2 full cells exhibit remarkable cycling stability for 700 cycles in aqueous electrolytes with MBA additives. The additive engineering via MBA achieved the dendrite-free Zn anodes and stable full batteries, which is favorable for advanced AZIBs in practical applications.

Accelerated and Guided Zn2+ Diffusion via Polarized Interface Engineering Toward High Performance Wearable Zinc-Ion Batteries.

Rechargeable aqueous Zn-ion batteries (ZIBs) are considered as a new energy storage device for wearable electronic equipment. Nowadays, dendrite growth and uneven deposition of zinc have been the principal problems to suppress the development of high-performance wearable zinc-ion batteries. Herein, a perovskite material of LaAlO3 nanoparticle has been applied for interface engineering and zinc anode protection. By adjusting transport channels and accelerating the Zn2+ diffusion, the hydrogen evolution reaction potential is improved, and electric field distribution on the Zn electrode surface is regulated to navigate the fast and uniform deposition of Zn2+. As a proof of demonstration, the assembled LAO@Zn||MnO2 batteries can display the highest capacity of up to 140 mAh g-1 without noticeable decay even after 1000 cycles. Moreover, a motor-driven fan and electronic wristwatch powered by wearable ZIBs can demonstrate the practical feasibility of LAO@Zn||MnO2 in wearable electronic equipment.

Three-in-One Zinc Anodes Created by a Large-scale Two-Step Method Achieving Excellent Long-Term Cyclic Reversibility and Thin Electrode Integrity.

Practical aqueous zinc-ion batteries require low-cost thin zinc anodes with long-term reversible stripping/depositing. However, thin zinc anodes encounter more severe issues than thick zinc, such as dendrites and uneven stripping, resulting in subpar performance and limited lifetimes. Here, this work proposes a three-in-one zinc anode obtained by a large-scale two-step method to address the above issues. In a three-in-one zinc anode, the copper foil as an inactive current collector solves the gradual reduction of the active area when only the pure zinc as an active current collector. This work develops an automatic electroplating device that can continuously deposit a zinc layer on a conducting foil to meet the demand for zinc-coated copper foils. The sodium carboxymethylcellulose (CMC)-zinc fluoride (ZnF2) protective layer prevents direct contact between zinc and separator, and provides a uniform and sufficient supply of zinc ions. The CMC-ZnF2-coated copper foil performs up to 3000 reversible zinc deposition/stripping cycles with a cumulative capacity of 6 Ah cm-2 and an average Coulombic efficiency of 99.94%. The Zn||ZnVO cell using the three-in-one anode achieved a high capacity retention of over 70% after 15 000 cycles. The proposed three-in-one anode and the automatic electroplating device will facilitate industrialization of practical thin zinc anodes.

Regulating Zn2+ Migration-Diffusion Behavior by Spontaneous Cascade Optimization Strategy for Long-Life and Low N/P Ratio Zinc Ion Batteries.

Parasitic side reactions and dendrite growth on zinc anodes are formidable issues causing limited lifetime of aqueous zinc ion batteries (ZIBs). Herein, a spontaneous cascade optimization strategy is first proposed to regulate Zn2+ migration-diffusion behavior. Specifically, PAPE@Zn layer with separation-reconstruction properties is constructed in situ on Zn anode. In this layer, well-soluble poly(ethylene oxide) (PEO) can spontaneously separation to bulk electrolyte and weaken the preferential coordination between H2O and Zn2+ to achieve primary optimization. Meanwhile, poor-soluble polymerized-4-acryloylmorpholine (PACMO) is reconstructed on Zn anode as hydrophobic flower-like arrays with abundant zincophilic sites, further guiding the de-solvation and homogeneous diffusion of Zn2+ to achieve the secondary optimization. Cascade optimization effectively regulates Zn2+ migration-diffusion behavior, dendrite growth and side reactions of Zn anode are negligible, and the stability is significantly improved. Consequently, symmetrical cells exhibit stability over 4000 h (1 mA cm-2). PAPE@Zn//NH4 +-V2O5 full cells with a high current density of 15 A g-1 maintains 72.2 % capacity retention for 12000 cycles. Even better, the full cell demonstrates excellent performance of cumulative capacity of 2.33 Ah cm-2 at ultra-low negative/positive (N/P) ratio of 0.6 and a high mass-loading (~17 mg cm-2). The spontaneous cascade optimization strategy provides novel path to achieve high-performance and practical ZIBs.

Ultra-High Proportion of Grain Boundaries in Zinc Metal Anode Spontaneously Inhibiting Dendrites Growth.

Aqueous Zn-ion batteries are an attractive electrochemical energy storage solution for their budget and safe properties. However, dendrites and uncontrolled side reactions in anodes detract the cycle life and energy density of the batteries. Grain boundaries in metals are generally considered as the source of the above problems but we present a diverse result. This study introduces an ultra-high proportion of grain boundaries on zinc electrodes through femtosecond laser bombardment to enhance stability of zinc metal/electrolyte interface. The ultra-high proportion of grain boundaries promotes the homogenization of zinc growth potential, to achieve uniform nucleation and growth, thereby suppressing dendrite formation. Additionally, the abundant active sites mitigate the side reactions during the electrochemical process. Consequently, the 15 µm Fs-Zn||MnO2 pouch cell achieves an energy density of 249.4 Wh kg-1 and operates for over 60 cycles at a depth-of-discharge of 23 %. The recognition of the favorable influence exerted by UP-GBs paves a new way for other metal batteries.

Interface engineering enabled by sodium dodecyl sulfonate surfactant for stable Zn metal batteries.

Aqueous zinc-ion batteries are emerging as powerful candidates for large-scale energy storage, due to their inherent high safety and high theoretical capacity. However, the inevitable hydrogen evolution and side effects of the deposition process limit their lifespan, which requires rational engineering of the interface between anode and aqueous electrolyte. In this paper, an anionic surfactant as electrolyte additive, sodium dodecyl sulfonate (SDS), is introduced to deliver highly reversible zinc metal batteries. Unlike traditional surfactants, the solvation structure is not affected by SDS, which tends to adsorb on the (002) crystal plane of Zn with the purpose of effectively limiting the water molecules adsorption. Attributed to the natural hydrophobic part of SDS, a dynamic electrostatic shielding layer and a unique hydrophobic interface are constructed on the anode. Assisted by the above merits, the adverse surface corrosion, hydrogen evolution and dendrite growth are significantly inhibited without the sacrifice in the deposition kinetics of Zn ions. As a result, the Zn||Zn symmetric batteries demonstrate an increased cycle life of 2000 h (1 mA cm-2, 1 mA h cm-2) with the presence of SDS additive. Such strategy provides a new avenue for the developing advanced electrolytes to be applied in aqueous energy storage systems.

Dendrite-free Zn anode enabled by combining carbon nanoparticles hydrophobic layer with crystal face reconstruction toward high-performance Zn-ion battery.

Aqueous zinc ion batteries (ZIBs) have been considered promising energy storage systems due to their excellent electrochemical performance, environmental toxicity, high safety and low cost. However, uncontrolled dendrite growth and side reactions at the zinc anode have seriously hindered the development of ZIBs. Herein, we prepared the carbon nanoparticles layer coated zinc anode with (103) crystal plane preferential oriented crystal structure (denoted as C@RZn) by a facile one-step vapor deposition method. The preferential crystallographic orientation of (103) crystal plane promotes zinc deposition at a slight angle, effectively preventing the formation of Zn dendrites on the surface. In addition, the hydrophobic layer of carbon layer used as an inert physical barrier to prevent corrosion reaction and a buffer during volume changes, thus improving the reversibility of the zinc anode. As a result. the C@RZn anode achieves a stable cycle performance of more than 3000 h at 1 mA cm-2 with CE of 99.77 % at 5 mA cm-2. The full battery with C@RZn anode and Mn-doped V6O13 (MVO) cathode show stability for 5000 cycles at the current density of 5 A g-1. This work provides a new approach for the design of multifunctional interfaces for Zn anode.

Stable Zinc Anode Facilitated by Regenerated Silk Fibroin-modified Hydrogel Protective Layer.

Inherent dendrite growth and side reactions of zinc anode caused by its unstable interface in aqueous electrolytes severely limit the practical applications of zinc-ion batteries (ZIBs). To overcome these challenges, a protective layer for Zn anode inspired by cytomembrane structure is developed with PVA as framework and silk fibroin gel suspension (SFs) as modifier. This PVA/SFs gel-like layer exerts similar to the solid electrolyte interphase, optimizing the anode-electrolyte interface and Zn2+ solvation structure. Through interface improvement, controlled Zn2+ migration/diffusion, and desolvation, this buffer layer effectively inhibits dendrite growth and side reactions. The additional SFs provide functional improvement and better interaction with PVA by abundant functional groups, achieving a robust and durable Zn anode with high reversibility. Thus, the PVA/SFs@Zn symmetric cell exhibits an ultra-long lifespan of 3150 h compared to bare Zn (182 h) at 1.0 mAh cm-2-1.0 mAh cm-2, and excellent reversibility with an average Coulombic efficiency of 99.04% under a large plating capacity for 800 cycles. Moreover, the PVA/SFs@Zn||PANI/CC full cells maintain over 20 000 cycles with over 80% capacity retention under harsh conditions at 5 and 10 A g-1. This SF-modified protective layer for Zn anode suggests a promising strategy for reliable and high-performance ZIBs.

Erythritol as a Saccharide Multifunctional Electrolyte Additive for Highly Reversible Zinc Anode.

Dendrite formation and water-triggered side reactions on the surface of Zn metal anodes severely restrict the commercial viability of aqueous zinc-ion batteries (AZIBs). In this work, we introduce erythritol (Et) as an electrolyte additive to enhance the reversibility of zinc anodes, given its cost-effectiveness, mature technology, and extensive utilization in various domains such as food, medicine, and other industries. By combining multiscale theoretical simulation and experimental characterization, it was demonstrated that Et molecules can partially replace the coordination H2O molecules to reshape the Zn2+ solvation sheath and destroy the hydrogen bond network of the aqueous electrolyte. More importantly, Et molecules tend to adsorb on the zinc anode surface, simultaneously inhibit water-triggered side reactions by isolating water and promote uniform and dense deposition by accelerating the Zn2+ diffusion and regulating the nucleation size of the Zn grain. Thanks to this synergistic mechanism, the Zn anode can achieve a cycle life of more than 3900 h at 1 mA cm-2 and an average Coulombic efficiency of 99.77%. Coupling with δ-MnO2 cathodes, the full battery delivers a high specific capacity of 228.1 mAh g-1 with a capacity retention of 76% over 1000 cycles at 1 A g-1.

Surface Engineering on Zinc Anode for Aqueous Zinc Metal Batteries.

Rechargeable aqueous zinc metal batteries (AZMBs) are considered as a potential alternative to lithium-ion batteries due to their low cost, high safety, and environmental friendliness. However, the Zn anodes in AZMBs face severe challenges, such as dendrite growth, metal corrosion, and hydrogen evolution, all of which are closely related to the Zn/electrolyte interface. This article offers a short review on surface passivation to alleviate the issues on the Zn anodes. The composition and structure of the surface layers significantly influence their functions and then the performance of the Zn anodes. The recent progresses are introduced, according to the chemical components of the passivation layers on the Zn anodes. Moreover, the challenges and prospects of surface passivation in stabilizing Zn anodes are discussed, providing valuable guidance for the development of AZMBs.

Rational Design of an In-Situ Polymer-Inorganic Hybrid Solid Electrolyte Interphase for Realising Stable Zn Metal Anode under Harsh Conditions.

The in-depth understanding of the composition-property-performance relationship of solid electrolyte interphase (SEI) is the basis of developing a reliable SEI to stablize the Zn anode-electrolyte interface, but it remains unclear in rechargeable aqueous zinc ion batteries. Herein, a well-designed electrolyte based on 2 M Zn(CF3SO3)2-0.2 M acrylamide-0.2 M ZnSO4 is proposed. A robust polymer (polyacrylamide)-inorganic (Zn4SO4(OH)6.xH2O) hybrid SEI is in situ constructed on Zn anodes through controllable polymerization of acrylamide and coprecipitation of SO4 2- with Zn2+ and OH-. For the first time, the underlying SEI composition-property-performance relationship is systematically investigated and correlated. The results showed that the polymer-inorganic hybrid SEI, which integrates the high modulus of the inorganic component with the high toughness of the polymer ingredient, can realize high reversibility and long-term interfacial stability, even under ultrahigh areal current density and capacity (30 mA cm-2~30 mAh cm-2). The resultant Zn||NH4V4O10 cell also exhibits excellent cycling stability. This work will provide a guidance for the rational design of SEI layers in rechargeable aqueous zinc ion batteries.

Synergistic Cation-π Interactions and PEDOT-Based Protective Double-Layer for High Performance Zinc Anode.

Ensuring effective and controlled zinc ion transportation is crucial for functionality of the solid electrolyte interphase (SEI) and overall performance in zinc-based battery systems. Herein the first-ever demonstration of incorporate cation-π interactions are provided in the SEI to effectively facilitate uniform zinc ion flux. The artificial SEI design involves the immobilization of 4-amino-p-terphenyl (TPA), a strong amphiphilic cation-π interaction donor, as a monolayer onto a conductive poly(3,4-ethylenedioxythiophene) (PEDOT) matrix, which enable the establishment of a robust network of cation-π interactions. Through a carefully-designed interfacial polymerization process, a high-quality, large-area, robust is achieved, thin polymeric TPA/PEDOT (TP) film for the use of artificial SEI. Consequently, this interphase exhibits exceptional cycling stability with low overpotential and enables high reversibility of Zn plating/stripping. Symmetrical cells with TP/Zn electrodes can be cycled for more than 3200 hours at 1 mA cm-2 and 1 mAh cm-2 . And the asymmetric cells can cycle 3000 cycles stably with a high Coulomb efficiency of 99.78%. Also, under the extreme conditions of lean electrolyte and low N/P ratio, the battery with TP protective layer can still achieve ultra-stable cycle.