The force at the implant cannot be assessed by the mallet force-Unless supported by a model.

The implantation of uncemented prostheses requires the application of sufficient forces to achieve a press-fit of the implant in the bone. Excessive forces have to be omitted to limit bone damage. Force measurements along the force transmission path between mallet and implant are frequently used to investigate this trade-off. Placing a load cell at a position of interest (PoI), which might be the implant bone interface or the head taper junction, is technically challenging or even impossible so that nearby positions are chosen. Thus, a certain inertia and stiffness remain between the PoI and the sensor, and consequently the measured dynamic forces differ from those at the PoI. This experimental and numerical study aimed to investigate the amount of force reduction along the transmission path while joining femoral heads to stem tapers. Forces were measured in vitro at the tip of the mallet, directly above the polymer tip of the impactor and below the stem taper. Springs and masses were used to represent the responding tissue of a patient. A semi-empirical numerical model of the force transmission path was developed and validated in order to simulate a larger range of responding tissue properties than experimentally possible and to investigate the influence of different surgical instruments. A distinct attenuation was observed since the peak forces at the impactor reached 35% of the applied peak forces and 21% at the stem taper, respectively. The force curves were replicated with a median root mean square error of 3.8% of the corresponding mallet blow for the impactor and 3.6% for the stem. The force measurement position and the used surgical instruments have a strong influence on the measured forces. Consequently, the exact measurement conditions with regard to sensor positioning and used surgical instruments have to be specified and hence only studies with similar setups should be compared to avoid misestimation of the forces at the PoI. The proposed dynamic numerical model is a useful tool to calculate the impact of the chosen or changed mechanical parameters prior to executing experiments and also to extrapolate the effect of changing the applied forces to the resulting forces at the PoI.

The small screw-apex distance is potentially associated with femoral head osteonecrosis in adults with femoral neck fractures treated by closed reduction and percutaneous 3 parallel cannulated screws.

OBJECTIVE: Femoral neck fractures (FNFs) are among the most common fractures in elderly individuals. Surgery is the main treatment for FNFs, and osteonecrosis of the femoral head (ONFH) is one of the unacceptable complications. This study aimed to assess both the clinical and radiological outcomes in patients with FNFs treated with three parallel cannulated screws and to identify relationship between screws position and ONFH. PATIENTS AND METHODS: A total of 100 patients who were treated with closed reduction and fixed with 3 parallel cannulated screws met the inclusion criteria between January 2014 and December 2020 at authors' institution. The follow-up duration, age, sex, affected side, and injury-to-surgery interval were collected; the neck-shaft angle of both hips, screw-apex distance (SAD) and the tip-apex distance (TAD)were measured; and the Garden classification, quality of reduction and presence of ONFH were evaluated. RESULTS: The sample consisted of 37 males and 63 females, with 60 left and 40 right hips affected. The mean age of patients was 54.93 ± 12.24 years, and the mean follow-up was 56.3 ± 13.38 months. The overall incidence of ONFH was 13%. No significant difference was observed in the incidence of ONFH by affected side, age, fracture displacement, injury-to-surgery interval, neck-shaft angle deviation, or reduction quality. The SAD was significantly shorter in ONFH patients than in normal patients for all three screws (p = 0.02, 0.02, and 0.01, respectively). CONCLUSIONS: The short SAD of all screws is associated with femoral head necrosis of FNFs treated with 3 cannulated screws. The short SAD indicated that screws malpositioning in the weight-bearing area of the femoral head, potentially harming the blood supply and compromising the anchorage of the primary compressive trabeculae in this region.

Arthroscopic Femoral Head Allograft With Proximal Femoral/Periacetabular Osteotomies for Sequelae of Perthes: A Case Report.

CASE: We describe the unique case of a 20-year-old man with a history of Legg-Calve-Perthes disease, hip dysplasia, and osteochondral fragmentation of the medial femoral head. We performed arthroscopic femoroplasty and femoral head allografting, followed by a valgus-producing derotational femoral osteotomy (DFO) and periacetabular osteotomy (PAO). At 1-year follow-up, the patient achieved osseous union and complete femoral head healing with return to his active hobbies. CONCLUSION: We describe the successful utilization of arthroscopic allografting for medial femoral head osteochondral fragmentation. To our knowledge, this is the first report on femoral head arthroscopic allografting before DFO and PAO.

The influence of surgical technique guidance and surgeon's experience on the femoral head assembly in total hip arthroplasty.

INTRODUCTION: The importance of the assembly procedure on the taper connection strength is evident. However, existent surgical technique guides frequently lack comprehensive and precise instructions in this regard. The aim of our experimental study was to evaluate the influence of the surgical technique guide on the femoral head assembly procedure in surgeons with differing levels of experience in total hip arthroplasty. MATERIALS AND METHODS: Twenty-eight participants, divided into four groups based on their lifetime experience in total hip arthroplasty, conducted a femoral head assembly procedure in a simulated intraoperative environment before and after reviewing the surgical technique guide. Demographic information and the number of hammer blows were documented. Hammer velocity and impaction angle were recorded using an optical motion capturing system, while the impaction force was measured using a dynamic force sensor within the impactor. RESULTS: We observed a high variation in the number of hammer blows, maximum force, and impaction angle. Overall, the number of hammer blows decreased significantly from 3 to 2.2 after reviewing the surgical technique guide. The only significant intragroup difference in the number of hammer blows was observed in the group with no prior experience in total hip arthroplasty. No correlation was found between individual factors (age, weight, height) or experience and the measured parameters (velocity, maximum force and angle). CONCLUSIONS: The present study demonstrated a high variation in the parameters of the femoral head assembly procedure. Consideration of the surgical technique guide was found to be a limited factor among participants with varying levels of experience in total hip arthroplasty. These findings underline the importance of sufficient preoperative training, to standardize the assembly procedure, including impaction force, angle, and use of instruments.

Lower Risk of Revision With 32- and 36-Millimeter Femoral Heads Compared With 28-mm Heads in Primary Total Hip Arthroplasty: A Comparative Single-Center Study (10,104 Hips).

BACKGROUND: We aimed to compare the clinical outcomes of different head sizes (28-, 32-, and 36- millimeter) in primary total hip arthroplasty (THA) at mean 6 years follow-up (range, 1 to 17.5 years). METHODS: This was a retrospective consecutive study of primary THA at our institution (2003 to 2019). Demographic and surgical data were collected. The primary outcome measures were all-cause revision, revision for dislocation, and all-cause revision excluding dislocation. Continuous descriptive statistics used means, median values, ranges, and 95% confidence intervals, where appropriate. Kaplan-Meier survival curves were used to estimate time to revision. Cox proportional hazard regression analyses were used to compare revision rates between the femoral head size groups. Adjustments were made for age at surgery, sex, primary diagnosis, American Society of Anesthesiologists score, articulation type, and fixation methods. There were 10,104 primary THAs included; median age was 69 years (range, 13 to 101) with 61.5% women. A posterior approach was performed in 71.6%. There were 3,295 hips with 28-mm heads (32.6%), 4,858 (48.1%) with 32-mm heads, and 1,951 (19.3%) with 36-mm heads. RESULTS: Overall rate of revision was 1.7% with the lowest rate recorded for the 36-mm group (2.7 versus 1.3 versus 1.1%). Cox regression analyses showed a decreased risk of all-cause revision for 32 and 36-mm head sizes as compared to 28-mm; this was statistically significant for the 32-mm group (P = .01). Risk of revision for dislocation was significantly reduced in both 32-mm (P = .03) and 36-mm (P = .03) head sizes. Analysis of all cause revision excluding dislocation showed no significant differences between head sizes. CONCLUSIONS: We found a significantly reduced risk of revision for all causes, but particularly revision for dislocation with larger head sizes. Concerns regarding increased risk of early revision for aseptic loosening, polyethylene wear, or taper corrosion with larger heads appear to be unfounded in this cohort of 10,104 patients with up to 17 years follow-up.

Application direct anterior approach in pediatric femoral head and neck lesions.

BACKGROUND: Femoral neck is one of the high-risk areas for benign tumors and tumor-like lesions. Small range of lesions may also lead to pathological fracture, femoral head necrosis and other serious problems. PURPOSE: To investigate a new minimally invasive surgical approach to resect femoral head and neck lesions in children. PATIENTS AND METHODS: Retrospective study of 20 patients with femoral neck and femoral head lesions from February 2019 to March 2023 in our hospital. Among them, 14 were boys and 6 were girls, 17 were femoral neck lesions and 3 were femoral head lesions. The age of the patients ranged from 3.2 to 12.6 years, with a mean of 7.1 years. The patients were divided into group A and group B according to different surgical approaches; group A used the Smith-Peterson approach, Watson-Jones approach or surgical dislocation approach and group B used the DAA. Intra-operatively, incision length, operative time and blood loss were recorded in both groups. Group A consisted of 1 femoral head lesion and 8 femoral neck lesions, including 5 cases of bone cyst and 4 cases of eosinophilic granuloma. Group B consisted of 2 femoral head lesion and 9 femoral neck lesions. A total of 11 patients with different types of disease were included in group B, including bone cysts (3 cases), aneurysmal bone cysts (1 case), eosinophilic granulomas (6 cases), Kaposi's sarcoma (1 case). RESULTS: The two groups of patients differed in terms of incision length (P < 0.05), operative blood loss (P < 0.05) and operative time (P < 0.05). At 6-48 months post-operatively, there were no significant differences in function and all patients had good hip function. CONCLUSION: The direct anterior approach is effective for resection of paediatric femoral head and neck lesions. It provides clear exposure of the surgical site, minimal trauma and does not compromise the integrity of the anterior musculature. LEVEL OF EVIDENCE: III.

Ganz femoral head reduction associated with coverage and containment procedures improve radiological and functional outcomes in Perthes' disease.

Aims: Ganz's studies made it possible to address joint deformities on both the femoral and acetabular side brought about by Perthes' disease. Femoral head reduction osteotomy (FHRO) was developed to improve joint congruency, along with periacetabular osteotomy (PAO), which may enhance coverage and containment. The purpose of this study is to show the clinical and morphological outcomes of the technique and the use of an implemented planning approach. Methods: From September 2015 to December 2021, 13 FHROs were performed on 11 patients for Perthes' disease in two centres. Of these, 11 hips had an associated PAO. A specific CT- and MRI-based protocol for virtual simulation of the corrections was developed. Outcomes were assessed with radiological parameters (sphericity index, extrusion index, integrity of the Shenton's line, lateral centre-edge angle (LCEA), Tönnis angle), and clinical parameters (range of motion, visual analogue scale (VAS) for pain, Merle d'Aubigné-Postel score, modified Harris Hip Score (mHHS), and EuroQol five-dimension five-level health questionnaire (EQ-5D-5L)). Early and late complications were reported. Results: The mean follow-up was 39.7 months (standard deviation (SD) 26.4). The mean age at surgery was 11.4 years (SD 1.6). No major complications were recorded. One patient required a total hip arthroplasty. Mean femoral head sphericity increased from 46.8% (SD 9.34%) to 70.2% (SD 15.44; p < 0.001); mean LCEA from 19.2° (SD 9.03°) to 44° (SD 10.27°; p < 0.001); mean extrusion index from 37.8 (SD 8.70) to 7.5 (SD 9.28; p < 0.001); and mean Tönnis angle from 16.5° (SD 12.35°) to 4.8° (SD 4.05°; p = 0.100). The mean VAS improved from 3.55 (SD 3.05) to 1.22 (1.72; p = 0.06); mean Merle d'Aubigné-Postel score from 14.55 (SD 1.74) to 16 (SD 1.6; p = 0.01); and mean mHHS from 60.6 (SD 18.06) to 81 (SD 6.63; p = 0.021). The EQ-5D-5L also showed significant improvements. Conclusion: FHRO associated with periacetabular procedures is a safe technique that showed improved functional, clinical, and morphological outcomes in Perthes' disease. The newly introduced simulation and planning algorithm may help to further refine the technique.

Investigational regenerative medicine for non-traumatic osteonecrosis of the femoral head: a survey of registered clinical trials.

INTRODUCTION: Osteonecrosis of the femoral head (ONFH) is a refractory disease requiring joint replacement in young patients. Regenerative therapies have been developed. AREAS COVERED: This study surveyed clinical trials on regenerative medicine for ONFH. We extracted clinical trials on non-traumatic ONFH from the websites of five publicly available major registries (EuropeanUnion Clinical Trials Register ([EU-CTR],ClinicalTrials.gov, Chinese ClinicalTrial Registry [ChiCTR], University Hospital Medical InformationNetwork - Clinical Trial Registry [UMIN-CTR] and Australian New Zealand Clinical Trials Registry [ANZCTR]).The trials were classified into six categories based on purpose: surgical treatment, non-drug conservative treatment, conservative drug treatment, therapeutic strategy, diagnosis and pathogenesis, and regenerative therapy.) We extracted 169 clinical trials on ONFH. Of these, 37 were on regenerative medicine, including 29 on cell therapy. Surgical treatment was the most common treatment, followed by regenerative therapy.There were 9 clinical trials registered in the EU-CTR, with 5 on regenerative medicine; 79 trials registered on ClinicalTrials.gov, with 24 on regenerativemedicine; 54 trials registered in the ChiCTR, with 6 on regenerative medicine. EXPERT OPINION: The focus of the joint-preserving surgery has shifted to regenerative therapy based on using cell therapy in early-stage ONFH. The global standardisation of regenerative therapy is still ongoing.

Computer-Assisted Arthroscopic Cam Resection.

Determining the appropriate femoral cam resection during hip arthroscopy for femoroacetabular impingement syndrome is both critical for the patient and challenging for the surgeon. Incomplete bone resection is a leading cause of failed hip arthroscopy, whereas over-resection may increase the risk of femoral neck fracture. The alpha angle is a validated 2-dimensional radiographic measurement used to both diagnose femoroacetabular impingement syndrome preoperatively and to determine resection adequacy postoperatively. Computer-assisted intraoperative guidance systems enhance the accuracy of femoral cam resection, although a preoperative 3-dimensional computed tomography scan may be required. Other systems, such as the HipCheck software (Stryker, Kalamazoo, MI), have been developed to provide intraoperative guidance with live feedback using simultaneous alpha angle measurements overlayed on fluoroscopic images without the requirement for routine preoperative computed tomography. Via intraoperative touchscreen navigation, the surgeon identifies the midpoint of the femoral neck and femoral head. A commercial software program provides real-time alpha angle measurements, as well as enhanced visualization of the femoral cam deformity with an adjustable resection curve. Before the surgeon performs the cam resection, the software provides a template for appropriate resection depth in 6 positions of the hip. Upon completion of the femoral cam resection, the hip is again assessed in the same 6 positions and the alpha angle is assessed to ensure a complete resection.

Femoral Head Core Decompressions: Characterization of Subsequent Conversion to Total Hip Arthroplasty and Related Complications.

BACKGROUND: Core decompression is a minimally invasive joint-preserving approach for early-stage osteonecrosis. The rate at which core decompression patients require total hip arthroplasty (THA) and rates of perioperative adverse outcomes have not been well-characterized. METHODS: Adult patients undergoing core decompression and/or THA with osteonecrosis of the femoral head were identified from the 2015 to 2021 Q3 PearlDiver M157 database. Those undergoing THA without or with antecedent core decompression were identified and matched 4:1 on age, sex, and Elixhauser Comorbidity Index. Postoperative 90-day adverse events were compared with multivariable analysis. Five-year rates of revision, dislocation, and periprosthetic fracture were compared by the Kaplan-Meier curve and log-rank tests. RESULTS: Core decompressions were identified for 3,025 patients of whom 387 (12.8%) went on to THA within 5 years (64% within the first year). The median time from initial core decompression to THA was 252 days. For THA, 26,209 adults were identified and 387 had prior core decompression. After matching, there were 1,320 without core decompression and 339 with core decompression. No statistically significant differences were observed in 90-day postoperative adverse events or 5-year rates of revision, dislocation, or periprosthetic fracture. CONCLUSION: Core decompression may be an option for patients with osteonecrosis and does not seem to affect THA outcomes if required later.

[Correlation analysis between combined deflection angle and osteonecrosis of femoral head after femoral neck fracture].

Objective: To evaluate the correlation between pelvic incidence (PI) angle, hip deflection angle (HDA), combined deflection angle (CDA) and osteonecrosis of the femoral head (ONFH) after femoral neck fracture, in order to explore early predictive indicators for ONFH occurrence after femoral neck fracture. Methods: A study was conducted on patients with femoral neck fractures who underwent cannulated screw internal fixation between December 2018 and December 2020. Among them, 208 patients met the selection criteria and were included in the study. According to the occurrence of ONFH, the patients were allocated into ONFH group and non-NOFH group. PI, HDA, and CDA were measured based on the anteroposterior X-ray films of pelvis and axial X-ray films of the affected hip joint before operation, and the differences between the two groups were compared. The receiver operating characteristic curve (ROC) was used to evaluate the value of the above imaging indicators in predicting the occurrence of ONFH. Results: Among the 208 patients included in the study, 84 patients experienced ONFH during follow-up (ONFH group) and 124 patients did not experience ONFH (non-ONFH group). In the non-ONFH group, there were 59 males and 65 females, the age was 18-86 years (mean, 53.9 years), and the follow-up time was 18-50 months (mean, 33.2 months). In the ONFH group, there were 37 males and 47 females, the age was 18-76 years (mean, 51.6 years), and the follow-up time was 8-45 months (mean, 22.1 months). The PI, HDA, and CDA were significantly larger in the ONFH group than in the non-ONFH group ( P<0.05). ROC curve analysis showed that the critical value of PI was 19.82° (sensitivity of 40.5%, specificity of 86.3%, P<0.05); the critical value of HDA was 20.94° (sensitivity of 77.4%, specificity of 75.8%, P<0.05); and the critical value of CDA was 39.16° (sensitivity of 89.3%, specificity of 83.1%, P<0.05). Conclusion: There is a correlation between PI, HDA, CDA and the occurrence of ONFH after femoral neck fracture, in which CDA can be used as an important reference indicator. Patients with CDA≥39.16° have a higher risk of ONFH after femoral neck fracture.

Time elapsed from definitive diagnosis to surgery for osteonecrosis of the femoral head: a nationwide observational study in Japan.

OBJECTIVES: This study documents the time elapsed from the diagnosis of osteonecrosis of the femoral head (ONFH) to surgery, exploring the factors that influence ONFH severity. DESIGN: Retrospective observational study of a nationwide database. SETTING: The Kaplan-Meier method with log-rank tests was applied to examine the period from definitive diagnosis of ONFH to surgery using any surgery as the end point. For bilateral cases, the date of the first surgery was the endpoint. PARTICIPANTS: This study included 2074 ONFH cases registered in 34 university hospitals and highly specialised hospitals of the multicentre sentinel monitoring system of the Japanese Investigation Committee between 1997 and 2018. MAIN OUTCOME MEASURE: The primary outcome was the time from diagnosis to surgery. The secondary outcome was the proportion of subjects remaining without surgery at 3, 6 and 9 months, and at 1, 2 and 5 years after diagnosis. RESULTS: The median time to surgery was 9 months (IQR 4-22 months) after diagnosis of ONFH. The time to surgery was significantly shorter in the alcohol alone group and the combined corticosteroid and alcohol group than in the corticosteroid alone group (p=0.018 and p<0.001, respectively), in early stage ONFH with no or mild joint destruction (stages II and III, p<0.001), and with joint preserving surgery (p<0.001). The proportion without surgery was 75.8% at 3 months, 59.6% at 6 months, 48.2% at 9 months, 40.5% at 1 year, 22.2% at 2 years and 8.3% at 5 years. CONCLUSION: ONFH has been considered to be an intractable disease that often requires surgical treatment, but the fact that surgery was performed in more than half of the patients within 9 months from diagnosis suggests severe disease with a significant clinical impact. TRIAL REGISTRATION NUMBER: Chiba University ID1049.

The size of the femoral head does not influence metal ion levels after metal-on-polyethylene total hip arthroplasty: a five-year report from a randomized controlled trial.

Aims: In metal-on-polyethylene (MoP) total hip arthroplasty (THA), large metal femoral heads have been used to increase stability and reduce the risk of dislocation. The increased size of the femoral head can, however, lead to increased taper corrosion, with the release of metal ions and adverse reactions. The aim of this study was to investigate the relationship between the size of the femoral head and the levels of metal ions in the blood in these patients. Methods: A total of 96 patients were enrolled at two centres and randomized to undergo MoP THA using either a 32 mm metal head or a femoral head of between 36 mm and 44 mm in size, being the largest possible to fit the thinnest available polyethylene insert. The levels of metal ions and patient-reported outcome measures (Oxford Hip Score, University of California, Los Angeles Activity Scale) were recorded at two and five years postoperatively. Results: At five years, the median levels of chromium, cobalt, and titanium were 0.5 µg/l (interquartile range (IQR) 0.50 to 0.62), 0.24 µg/l (IQR 0.18 to 0.30), and 1.16 µg/l (IQR 1.0 to 1.68) for the 32 mm group, and 0.5 µg/l (IQR 0.5 to 0.54), 0.23 µg/l (IQR 0.17 to 0.39), and 1.30 µg/l (IQR 1 to 2.05) for the 36 mm to 44 mm group, with no significant difference between the groups (p = 0.825, p = 1.000, p = 0.558). There were increased levels of metal ions at two years postoperatively in seven patients in the 32 mm group, compared with four in the 36 mm to 44 mm group, and at five years postoperatively in six patients in the 32 mm group, compared with seven in the 36 mm to 44 mm group. There was no significant difference in either the OHS (p = 0.665) or UCLA (p = 0.831) scores between patients with or without an increased level of metal ions. Conclusion: In patients who underwent MoP THA, we found no differences in the levels of metal ions five years postoperatively between those with a femoral head of 32 mm and those with a femoral head of between 36 mm and 44 mm, and no corrosion-related revisions. As taper corrosion can start after five years, there remains a need for longer-term studies investigating the relationship between the size of the femoral head size and corrosion in patients undergoing MoP THA.

Evaluation of the long-term patient-reported outcomes after hip arthroplasty or joint preserving with Sugioka femoral osteotomy in patients with femoral head osteonecrosis.

PURPOSE: This study retrospectively evaluated long-term clinical outcomes and patient-reported outcome measures (PROMs) in patients with osteonecrosis of the femoral head (ONFH) who underwent transtrochanteric rotational osteotomy (TRO), curved varus osteotomy (CVO), and total hip arthroplasty (THA). METHODS: We retrospectively reviewed the 109 hips in 96 patients (46 men, 50 women) who underwent CVO, TRO, or THA for ONFH treatment. The mean follow-up period for the TRO, CVO, and THA groups was 14.8, 11.5, and 13.3 years, respectively. RESULTS: The THA conversion rate of the TRO patients was significantly higher than that of the patients with CVO, and the final clinical scores in the patients with TRO did not improve compared with preoperative scores. Postoperative PROMs showed that the total and pain scores of the patients with THA were significantly higher than those of patients with TRO and CVO, while the PROM score did not change between patients with TRO and CVO. The analysis further showed that the preoperative type C2, stage 3A, or postoperative type C1 and C2 were significant predictors of decreased final PROM scores. CONCLUSION: This study found that CVO and THA are clinically effective treatments for ONFH, with significant improvements compared with preoperative scores. However, THA was associated with significantly higher PROMs and pain scores than those of CVO and TRO in long-term follow-up. Furthermore, our results suggest that postoperative PROMs depend mainly on the preoperative level of collapse and postoperative transposed intact ratio of the articular surface of the femoral head.

What are the differences in the recovery of physical function and clinical score between patients with steroid-related osteonecrosis of the femoral head and hip osteoarthritis undergoing total hip arthroplasty? A propensity score-matched study.

PURPOSE: Steroid-related osteonecrosis of the femoral head (ONFH), arising from steroid administration for underlying diseases, represents a unique pathology for total hip arthroplasty (THA) and typically affects a younger demographic compared to osteoarthritis (OA). Given the significant age-related differences, this study aims to employ propensity score matching to align patient backgrounds between these two diseases and compare physical function. Additionally, our objective is to scrutinize the patterns of clinical score recovery over the course of one year following THA. METHODS: Using propensity score matching, 29 patients each with steroid-related ONFH and OA were selected. Muscle strength (hip abductor and knee extensor) were assessed before and after THA. Additionally, recovery of the Harris Hip Score (HHS) and Oxford Hip Score (OHS) up to one year postoperatively was analyzed. RESULTS: The steroid-related ONFH group exhibited gender bias and significantly younger age compared to the OA group. Propensity score matching achieved balanced patient backgrounds. Physical function showed trends of lower hip abduction and knee extensor strength on the operative side in the steroid-related ONFH group. Notably, nonoperative knee extensor strength decreased significantly after matching. HHS and OHS were poor in steroid-related ONFH up to three months postoperatively but recovered after six months. CONCLUSIONS: Patients with steroid-related ONFH experience positive outcomes in clinical score following THA. Propensity score matching effectively identified muscle weakness on both operative and nonoperative sides, highlighting its utility in comparative analyses.

Long-term polyethylene wear rates and clinical outcomes of oxidized zirconium femoral heads on highly cross-linked polyethylene in total hip arthroplasty.

Aims: Oxidized zirconium (OxZi) and highly cross-linked polyethylene (HXLPE) were developed to minimize wear and risk of osteolysis in total hip arthroplasty (THA). However, retrieval studies have shown that scratched femoral heads may lead to runaway wear, and few reports of long-term results have been published. The purpose of this investigation is to report minimum ten-year wear rates and clinical outcomes of THA with OxZi femoral heads on HXLPE, and to compare them with a retrospective control group of cobalt chrome (CoCr) or ceramic heads on HXLPE. Methods: From 2003 to 2006, 108 THAs were performed on 96 patients using an OxZi head with a HXLPE liner with minimum ten-year follow-up. Harris Hip Scores (HHS) were collected preoperatively and at the most recent follow-up (mean 13.3 years). Linear and volumetric liner wear was measured on radiographs of 85 hips with a minimum ten-year follow-up (mean 14.5 years). This was compared to a retrospective control group of 45 THAs using ceramic or CoCr heads from October 1999 to February 2005, with a minimum of ten years' follow-up. Results: Average HHS improved from 50.8 to 91.9 and 51.0 to 89.8 in the OxZi group and control group, respectively (p = 0.644), with no osteolysis in either group. Linear and volumetric wear rates in the OxZi group averaged 0.03 mm/year and 3.46 mm3/year, respectively. There was no statistically significant difference in HHS scores, nor in linear or volumetric wear rate between the groups, and no revision for any indication. Conclusion: The radiological and clinical outcomes, and survivorship of THA with OxZi femoral heads and HXLPE liners, were excellent, and comparable to CoCr or ceramic heads at minimum ten-year follow-up. Wear rates are below what would be expected for development of osteolysis. OxZi-HXLPE is a durable bearing couple with excellent long-term outcomes.

Precise single column resection and reconstruction with femoral head plus total hip replacement for primary malignant peri-acetabulum tumors.

To evaluate whether single acetabular column can be reserved and the effect of reconstruction with femoral head plus total hip replacement (THR) for primary malignant peri-acetabulum tumors. From 2007 to 2015, nineteen patients with primary malignant peri-acetabulum tumors were enrolled. All cases underwent single column resection with clear surgical margins. Ten of the 19 tumor's resections were assisted by computer navigation. Femoral heads were applied to reconstruct anterior or posterior column defects; THR was used for joint reconstruction. The surgical safety, oncologic outcome and prosthesis survivorship and function were evaluated by regular follow-up. The average follow-up period was 65.9 months. Surgical margins contained wide resection in 12 cases and marginal resection in 7 cases. One patient with Ewing's sarcoma died 14 months postoperative due to lung metastasis. One case with chondrosarcoma had recurrence. One prosthesis was removed due to infection. The average MusculoSkeletal Tumor Society (MSTS) function score was 83.7%. Due to the relative small number of cases, there was no significant difference in the recurrence rate and prosthesis failure rate between the navigation group and non-navigation group. Single column resection and reconstruction with femoral head autograft plus THR is an effective, safe method with less complication rate and better functional outcome for patients with peri-acetabular tumors.

Minimally invasive femoral head fracture fixation using three-dimensional navigation: a technical note.

Femoral head fractures are rare traumatic injuries that are usually associated with hip dislocations. Open reduction and internal fixation are performed when indicated, but can be associated with a higher risk of avascular necrosis. We report the case of a 24-year-old patient with a Pipkin type II fracture dislocation of the femoral head fixed via a minimally invasive three-dimensional navigated internal fixation technique. This technique minimizes deep soft tissue dissection to the hip capsule and associated vascularity and allows for accurate implant positioning.Level of evidence: Therapeutic case report Level IV.

Effect of longer femoral head on leg length, offset, and range of motion in total hip arthroplasty: a simulation study.

In this study, we investigated the relationship between head length, leg length, offset, and dislocation resistance using range of motion (ROM) simulations based on computed tomography data to examine if a longer femoral head reduces the risk of dislocation. The femoral components were set to eliminate leg length differences with a + 0 mm head, and variations for + 4-, + 7-, and + 8-mm heads were analyzed. Offset and ROM were assessed when longer heads were used, with the leg length adjusted to be similar to that of the contralateral side. While internal rotation at flexion and external rotation at extension increased with + 4-mm longer heads, the + 7- and + 8-mm heads did not increase dislocation resistance. When adjusting for leg length, the longer heads showed no significant differences in offset and ROM. Enhancing dislocation resistance by solely increasing the offset with a longer head, while simultaneously adjusting the depth of stem insertion, may be a beneficial intraoperative technique. Although a + 4-mm longer head possibly increases ROM without impingement, heads extended by + 7 or + 8 mm may not exhibit the same advantage. Therefore, surgeons should consider this technique based on the implant design.

Is there still an indication for the Birmingham Hip Resurfacing in femoral head osteonecrosis?

PURPOSE: Osteonecrosis of the femoral head (ONFH) is a progressive hip disease. Hip resurfacing arthroplasty (HRA) is a preferred surgical procedure among hip arthroplasty performed in young patients. The aim of this study is to show the long-term clinical and radiological results of HRA procedures performed for patients suffering from ONFH. METHODS: Forty-five patients who underwent hip resurfacing with the diagnosis of femoral head osteonecrosis were included in the study. The Harris Hip Score (HHS) was used for clinical scoring of the patients. The blood chromium, cobalt, white blood cell (WBC) count, and CRP levels of patients were checked. Ultrasonography (USG) was performed for all patients at mid-term control checked for pseudo-tumours. For the radiological evaluation, acetabular inclination, stem shaft angle, prothesis-to-neck ratio, osteolysis zones, and heterotopic ossification were used. RESULTS: The mean age of the patients was 46.6 ± 9.3 years, and the mean follow-up period was 11.83 ± 2.9 years. The mean HHS was 90.3 ± 12.8 for final follow-up. The mean WBC value was 8.2 109/L, mean CRP value was 6.3 mg/L, mean chromium value was 4.9 µg/L, and mean cobalt value was 1.8 µg/L. Inclination changing 0.2°(p = 0.788), stem shaft angle changing 0.7°(p = 0.424), and neck-to-prosthesis ratio changing 0.01°(p = 0.075). No pseudo-tumours were detected in any patients in USG examination. CONCLUSION: HRA provides long-term implant survival and excellent clinical outcomes for end-stage ONFH patients with low complication rates.