Physical, mechanical and antibacterial properties of the orthodontic adhesive doped with S-TiO2.

Orthodontic adhesive doped with sulfur-modified TiO2 promotes antibacterial effect. The objective of the study was to characterize the physical, mechanical and antibacterial properties of the orthodontic bracket adhesive, doped with modified titanium dioxide nanoparticles. Sulfur-doped TiO2 was synthetized and morphological topography was analyzed with TEM and SEM imaging. The catalytic performance during the degradation of rhodamine B was assessed. Nanomaterial was added at four concentration (1, 3, 6, and 10 wt%) to a commercial orthodontic adhesive. The shear bond strength and microhardness of a resin-based orthodontic adhesive containing S-TiO2 were evaluated. The inhibitory effect of the pure and doped adhesives against Escherichia coli and Streptococcus mutans was examined. As the results, the highest antimicrobial activity and good adhesive properties were noticed for light-cured orthodontic adhesive doped with 3% of S-TiO2. In this case, orthodontic adhesives with strong and long-lasting bactericidal properties can be created through the incorporation of modified TiO2 without negatively influencing microhardnesses, and bonding ability. White spot lesion and demineralization, which occurs very often in patients during orthodontic treatment, can be therefore minimized.

Influence of luting strategies on dentin bond performance of self-adhesive resin luting cement in combination with a universal adhesive.

OBJECTIVES: This study aimed to evaluate the dentin bond performance of various resin luting cement (RLC) systems combined with universal adhesives in different luting strategies. MATERIALS AND METHODS: Three self-adhesive resin luting cements (SRLCs) were used with universal adhesives as primers. Twelve specimens per group were prepared to measure shear bond strength (SBS) under distinct luting strategies in etch-&-rinse and self-etch modes. Regarding luting strategies, the bonded specimens were categorized into four groups based on tooth primer application and the curing mode of the SRLC paste: (i) with light irradiation of the tooth primer (wL) + dual-cure mode (DC) of the SRLC paste, (ii) wL + self-cure mode (SC) of the SRLC paste, (iii) without light irradiation of the tooth primer (woL) + DC mode of the SRLC paste, and (iv) woL + SC mode of the SRLC paste. Specimens were also subjected to different storage conditions: 24 h in water (baseline condition) and 10,000 cycles of thermal cycling. RESULTS: Luting strategy, storage condition, and SRLC system type significantly influenced dentin SBS values in both etching modes. Notably, certain SRLCs exhibited significantly higher dentin SBS when the primer was light-irradiated compared with no primer irradiation. CONCLUSION: Most SRLCs demonstrated higher dentin bond strength with light-irradiated primers, suggesting potential enhancement of dentin bond performance via primer light irradiation.

Impact of acid and laser etching of enamel on microleakage in different adhesive systems.

This study aimed to evaluate the microleakage of light-cured and self-cured adhesives on enamel surfaces selectively etched with Er, Cr: YSGG laser or 35% phosphoric acid. A total of 60 class V cavities were prepared 1 mm above the cemento-enamel junction (CEJ). The specimens were randomly divided into six groups. Group 1: Clearfil SE Bond with no conditioning, Group 2: Tokuyama Universal Bond with no conditioning, Group 3: Clearfil SE Bond conditioned with 35% phosphoric acid, Group 4: Tokuyama Universal Bond conditioned with 35% phosphoric acid, Group 5: Clearfil SE Bond conditioned with Er, Cr: YSGG laser and Group 6: Tokuyama Universal Bond conditioned with Er, Cr: YSGG laser. Microleakage was evaluated qualitatively (visually) and quantitatively (ImageJ). The data were analyzed using IBM SPSS V23 and submitted to Kruskal-Wallis and Wilcoxon tests. The significance level was set at p < 0.05. In all evaluation methods, the microleakage scores exhibit significant differences (p*<0.001). Group 1 and Group 3 exhibited similar and lower microleakage values than the Group 5. In the occlusal margin, the microleakage values were similar in Group 2, Group 4, and Group 6, whereas in the gingival margin Group 4 showed significantly lower leakage compared to Group 2. Regardless of the etching protocols and adhesive systems used, less microleakage was observed on the occlusal surface than on the gingival surface. Phosphoric acid etching provides better results than laser etching for enamel surface treatment on both occlusal and gingival surfaces.

Effect of Acetylsalicylic Acid on Biological Properties of Novel Cement Based on Calcium Phosphate Doped with Ions of Strontium, Copper, and Zinc.

This study aimed to compare the biological properties of newly synthesized cements based on calcium phosphate with a commercially used cement, mineral trioxide aggregate (MTA). Strontium (Sr)-, Copper (Cu)-, and Zinc (Zn)-doped hydroxyapatite (miHAp) powder was obtained through hydrothermal synthesis and characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD), and energy dispersive X-ray spectrometry (EDX). Calcium phosphate cement (CPC) was produced by mixing miHAp powder with a 20 wt.% citric acid solution, followed by the assessment of its compressive strength, setting time, and in vitro bioactivity. Acetylsalicylic acid (ASA) was added to the CPC, resulting in CPCA. Biological tests were conducted on CPC, CPCA, and MTA. The biocompatibility of the cement extracts was evaluated in vitro using human dental pulp stem cells (hDPSCs) and in vivo using a zebrafish model. Antibiofilm and antimicrobial effect (quantified by CFUs/mL) were assessed against Streptococcus mutans and Lactobacillus rhamnosus. None of the tested materials showed toxicity, while CPCA even increased hDPSCs proliferation. CPCA showed a better safety profile than MTA and CPC, and no toxic or immunomodulatory effects on the zebrafish model. CPCA exhibited similar antibiofilm effects against S. mutans and L. rhamnosus to MTA.

Dentinal Tubule Occluding Efficacy Of Er: YAG Laser And Universal Adhesive Loaded With Nano-Carbonated Apatite.

ER:YAG laser and experimental resin-based dental adhesive loaded with functionalized carbonated apatite filler were used in this study to evaluate the dentin interaction in terms of penetration and occlusion of the dentinal tubules aiding in the control of dentin hypersensitivity (DH). Spheroidal Carbonated apatite nanoparticles (N-CAP), with an average size of 20±5 nm diameter, were synthesized, characterized, and incorporated in a universal adhesive "All Bond Universal, Bisco, USA", in (2% weight) concentration. Er:YAG laser "Lightwalker, FOTONA, EU" was adjusted to an energy output of 40mJ/ pulse and pulse repetition of 10 Hz for 10 seconds. Dentin specimens were prepared from the buccal surface of 75 extracted sound human molars. The specimens were randomly divided into five groups (n=15) according to the surface treatment: Group (L): Laser only; Group (LB): Laser in combination with adhesive; Group (LBN): Laser in combination with adhesive loaded with N-CAP; Group (B): adhesive only; and Group (BN): adhesive loaded with N-CAP. Depth of penetration and occlusion of the dentinal tubules were assessed using Environmental Scanning Electron Microscope Examination (ESEM). One-way ANOVA was used to compare groups, followed by a pairwise test for multiple comparisons (α=0.05). Groups (LB), and (LBN) showed the highest mean of dentinal tubules' penetration, with a non-significant difference between them. In contrast, the specimens treated with laser only (L) showed the most minor penetration. The employment of ER-YAG laser irradiation with the adhesive loaded with N-CAP was evaluated to be effective in penetrating and occluding the opened dentinal tubules.

Biological interaction, esthetics, handling, and loss rate of temporary luting cements - a clinical single-blind randomized controlled trial.

OBJECTIVES: To evaluate three temporary luting cements in terms of their restoration loss rates, biological interactions, esthetic properties, and handling characteristics. MATERIALS AND METHODS: 75 adults requiring fixed prosthodontics voluntarily participated in a single-blind, randomized controlled trial. After preparation, temporary restorations were luted with a randomly selected temporary luting cement (either Provicol QM Plus (PQP), Bifix Temp (BT), or Provicol QM Aesthetic (PQA)). Clinical examinations were performed one to two weeks after cementation. The following criteria were evaluated: tooth vitality, percussion, hypersensitivity, gingival bleeding, odor formation, esthetics, cement handling, removability, cleanability, and retention loss. Antagonistic teeth served as controls. Statistical analysis was performed using the paired t-test, one-way ANOVA, Pearson's chi-square and Fisher's exact test, where appropriate. RESULTS: The overall loss rate of temporary restorations was 16.0%, showing no cement-specific differences. Postoperative hypersensitivity occurred in 8% of cases regardless of cement type. Esthetic impairment was reported by 31% of the PQP-fixed restorations, compared with 4.0% and 4.2% of the BT and PQA-bonded restorations. Cement application was reported to be easy in 100% of cases, excess removal in 88-96%, depending on the cement used. CONCLUSIONS: The choice of luting material affects the esthetic appearance of a temporary restoration and should be considered, particularly in restorations in esthetically demanding areas. No significant differences between the cements were identified regarding biocompatibility, handling, and loss rate. CLINICAL RELEVANCE: Translucent cements can help to reduce color interferences, resulting in a more appealing appearance of the temporary restoration.

Engineering Interfacial Integrity with Hydrolytic-Resistant, Self-Reinforcing Dentin Adhesive.

The leading cause of composite restoration failure is secondary caries, and although caries is a multifactorial problem, weak, damage-prone adhesives play a pivotal role in the high susceptibility of composite restorations to secondary caries. Our group has developed synthetic resins that capitalize on free-radical polymerization and sol-gel reactions to provide dental adhesives with enhanced properties. The resins contain γ-methacryloxypropyltrimethoxysilane (MPS) as the Si-based compound. This study investigated the properties of methacrylate-based resins containing methacryloxymethyltrimethoxysilane (MMeS) as a short-chain alternative. The degree of conversion (DC), polymerization kinetics, water sorption, mechanical properties, and leachates of MMeS- and MPS-resins with 55 and 30 wt% BisGMA-crosslinker were determined. The formulations were used as model adhesives, and the adhesive/dentin (a/d) interfaces were analyzed using chemometrics-assisted micro-Raman spectroscopy. The properties of the 55 wt% formulations were comparable. In the 30 wt% BisGMA formulations, the MMeS-resin exhibited faster polymerization, lower DC, reduced leachates, and increased storage and loss moduli, glass transition (Tg), crosslink density, and heterogeneity. The spectroscopic results indicated a comparable spatial distribution of resin, mineralized, and demineralized dentin across the a/d interfaces. The hydrolytically stable experimental short-chain-silane-monomer dental adhesive provides enhanced mechanical properties through autonomous strengthening and offers a promising strategy for the development of restorative dental materials with extended service life.

Effect of bioceramic intracanal medication on the dentinal bond strength of bioceramic cements: an ex-vivo study.

Background: The present study evaluated the effect of a bioceramic intracanal medicament (Bio-C Temp) on the push-out bond strength of bioceramic cements. Methods: Forty-eight human single-canaled premolars were prepared and randomly divided into three groups: Group (A) received no intracanal medicament; Group (B) calcium hydroxide (CH); and Group (C) Bio-C Temp. After medicament removal, the roots were sectioned transversely. The slices in each group were separated into two subgroups (n = 16): in Subgroup (1), mineral trioxide aggregate (MTA) was placed, and in Subgroup (2) Bio-C Repair. Push-out bond strength was determined using a universal testing machine, applying a constant compressive force on the cement until bond failure. The failure mode was also evaluated. Data were analyzed using the Chi-square test and two-way ANOVA followed by Tukey's post hoc tests. The level of significance was set at 5%. Results: The pushout bond strength of Bio-C Repair was significantly higher than that of MTA irrespective of intracanal medication (p = 0.005). The placement of Bio-C Temp was associated with significantly lower bond strength (p = 0.002, p = 0.001). Conclusion: Bio-C Repair showed better bond strength compared to MTA, irrespective of intracanal medication. Bio-C Temp intracanal medicament, however, decreased the bond strength of both these cements.

Experimental Bracket Design Performance on Bonding and Polymerization of Orthodontic Composite.

Objective: To evaluate the enamel bonding ability and orthodontic adhesive resin degree of conversion using the experimental bracket design. Material and Methods. Thirteen bovine teeth were used in the study. The experimental bracket was modified with a translucent region in the center of its body. After enamel etching, Orthocem orthodontic adhesive (FGM, Joinville, Brazil) was applied on the bracket base for bonding. The groups were divided as follows (n = 10 per group): (1) control (CB) with standard brackets and (2) spot bracket (SB) with experimental brackets featuring a 0.8 mm translucent region at the center using carbide bur. Shear bond strength (SBS) was evaluated after 24 hours in a universal testing machine and adhesive remnant index (ARI). The degree of conversion (DC) was analyzed using Raman spectroscopy (n = 3 per group). Data were then analyzed using Student's t-test and Mann-Whitney statistical methods. Results: The SB group exhibited a higher mean SBS (10.33 MPa) compared to the CB Group (8.77 MPa). However, there was no statistical difference between the groups (p = 0.376). Both SB and CB groups had a mean ARI score of 1. Raman analysis revealed a higher degree of conversion in the SB group (49.3%) compared to the CB group (25.9%). Conclusions: The experimental support showed a higher degree of adhesive conversion, although there was no significant increase in bond strength.

[Impact of chemical surface treatment of samples made of domestic zirconium dioxide on adhesive strength]. / Vliyanie khimicheskikh metodov podgotovki poverkhnosti obraztsov iz otechestvennogo dioksida tsirkoniya na pokazateli adgezionnoi prochnosti.

Ceramic based on zirconium dioxide (ZD) is a modern, durable material for the manufacture of dentures. It is known that ZD is not etched as glass-ceramic, making it difficult to prepare this material before fixing. OBJECTIVE: To study the impact of various methods of surface treatment of ZD-based ceramic on adhesive strength. MATERIALS AND METHODS: Sandblasting with Al2O3 particles sized 50 µm and application of primers with 10-MDP phosphate monomer were used. Adhesive strength values for following 4 groups of samples were obtained: 1st group - RelyX U200 + sandblasting + Compofix new primer (n=9); 2nd group - Compofix + sandblasting + Compofix new primer (n=9); 3rd group - Panavia F 2.0 + sandblasting (n=9); 4th group (control) - Variolink Esthetic DC + sandblasting + Monobond Plus primer (n=9). RESULTS: The highest strength of adhesion was in the 4th group - 48.71±5.71MPa, the smallest in the 3rd group - 9.49±35.24 MPa. Fully domestic components used in the 2nd group allowed to obtain values of 42.50±9.79 MPa. Adhesive strength in the 1st group was 34.11±4.78 MPa. CONCLUSION: The absence of the 10-MDP-based primers application in the preparation of ZD ceramic reduces the adhesive strength between resin cement and its surface. The domestic set for fixation of dentures can be effectively used for ZD on the same basis as European analogue.

[Study on the pressure on ceramic veneers during cementation]. / Izuchenie velichiny davleniya na keramicheskie viniry vo vremya ikh tsementirovaniya.

OBJECTIVE: The aim of the study is measuring the magnitude and determining the method of finger pressure exerted by doctors on ceramic veneers during their fixation. MATERIAL AND METHODS: A simulation model was designed in order to measure the volume of finger pressure. Veneers were produced for 2 central incisors. Doctors alternately placed veneers on the model and applied pressure on them for 20 seconds simulating the clinical stage of cementing. The operator recorded the maximum readings of the scales and entered the result on the research protocol. In addition, it was recorded which finger the doctor exerts on the veneer during its cementing to ensure a tight fit: thumb or index finger. RESULTS: The values obtained during cementation of 54% doctors ranged up to 1 kg, 27% of doctors from 1 to 2 kg and only 19% more than 2 kg. 80% of doctors applied the main pressure on the veneer using their thumb, while the pressure force was 1.4 kg. For those doctors who pressed the veneer to the tooth with their index finger, the impact value was 0.8 kg. CONCLUSION: The finger pressure on the veneer during cementation applied by dentists varies, the average pressure on the veneers was about 1.5 kg. The amount of pressure on cement during laboratory tests of cements for fixing veneers differs from clinical values many times. The development of a veneers fixation protocol, taking into account the conducted research, will ensure a reliable and accurate fit of the veneer at the stage of its cementing.

Degree of conversion of dual-cured composite luting agents: The effect of transition metal-based touch-cure activators.

PURPOSE: The aim of the study was (a) to assess the effect of universal adhesives and tooth primers with novel touch-cure activators on the conversion of dual-cured resin composite luting agents (RLAs) polymerized under the self-curing mode, and (b) to investigate the source of the catalytic effect exerted by the activators. MATERIALS AND METHODS: The materials selected were the adhesive RLAs Panavia V5/Tooth Primer (PV5/TP5), Variolink Esthetic DC/Adhese Universal DC (VLE/ADC), and the self-adhesive RLAs GCem ONE/AE Primer (GCO/AEP), RelyX Universal/Scotchbond Universal Plus (RXU/SUP) and Panavia SA Universal/Clearfil Universal Bond Quick (PSU/CUQ), the later serving as a control with an aryl-sulfinate activator. Coronal dentin specimens were prepared (n = 5/material), treated with the corresponding primers/adhesives (non-irradiated) and covered with a 100 µm-thick RLA layer (SC+A group). Three specimen series were additionally prepared (n = 3 × 5/material): A self-cured without the primers/adhesives (SC group), a dual-cured (20 s irradiation) with the corresponding primers/adhesives (DC+A group) and a dual-cured without primers/adhesives (DC group). All specimens were stored for 15 min (37 °C/dark/60 %RH). After demolding the degree of C = C conversion (DC%, top RLA surfaces) was measured by ATR-FTIR spectroscopy. The primer/adhesive liquids were further analyzed by ICP-MS and the microbrush tips of ADC by SEM-EDS. RESULTS: The touch-cure activators increased the DC% in all self-cured RLAs but failed to reach the values of the corresponding dual-cured RLAs. The effect of the activators in dual-cured specimens was negligible. The ICP-MS analysis showed the presence of V (AEP, TP5, ADC) and Cu (SUP) transitional metals in the activators, with V been located at the free ends of ADC tip bristles. The V activators demonstrated the highest DC% improvement in self-cured specimens. CONCLUSION: The new touch-cure activators significantly increased the conversion of the self-cured RLAs. Therefore, this step should be considered as universally applicable and not selective, as currently proposed for the self-adhesive luting agents by the manufacturers.

The effect of different deep margin elevation methods on the fracture strength of CAD-CAM restorations.

PURPOSE: To evaluate the effect of two resin composites (with different viscosities) and the elevation amount on fracture strength and fracture behavior of molars with and without deep margin elevations (DME). METHODS: 70 extracted, caries-free human molars were selected. All teeth were prepared as MOD onlay cavities with a margin 2 mm below the cemento-enamel junction (CEJ) on the mesial and buccal sides and 2 mm above the CEJ on the distal side. The teeth were divided into two groups according to the type of resin composite used in margin elevation, elevated with flowable composite (Universal Flo) or condensable composite (G-Aenial Posterior). These two groups were further subdivided into subgroups in which the elevation was 2, 3, or 4 mm, and a control group in which the non-elevated indirect restoration was directly bonded to the subgingival margin, making a total of seven groups (n= 10). After elevations, the restorations were completed using a nanoceramic CAD-CAM block (Cerasmart A3 HT) and as adhesive cement, G-Cem Link Force. Static force was applied to the restored teeth using a universal testing machine at an angle of 15° until fracture occurred. Fracture strength values were recorded, and fracture types were examined under 6x magnification. One-way ANOVA was carried out to determine the effect of DME on the fracture strength. A two-way ANOVA was conducted to investigate main and interaction effects of the material type used in the elevation and the amount of elevation made on the fracture strength (P< 0.05). RESULTS: Using flowable or condensable composite as elevation material did not affect the fracture strength of CAD-CAM restorations. Flowable and condensable composites of 2, 3, or 4 mm did not significantly affect fracture strength values for either material. Specimen margins with and without elevation exhibited similar fracture strength values. The type of material used in the elevation and the amount did not affect the fracture strength of teeth. CLINICAL SIGNIFICANCE: The deep margin elevation technique for teeth with carious lesions extending subgingivally, may be useful in routine practice.

Molecular insights to in vitro biocompatibility of endodontic Pulpotec with macrophages determined by oxidative stress and apoptosis.

Pulp therapy has been emerged as a one of the efficient therapies in the field of endodontics. Among different types of new endodontic materials, pulpotec has been materialized as a recognized material for vital pulp therapy. However, its efficacy has been challenged due to lack of information about its cellular biocompatibility. This study evaluates the mechanistic biocompatibility of pulpotec cement with macrophage cells (RAW 264.7) at cellular and molecular level. The biocompatibility was evaluated using experimental and computational techniques like MTT assay, oxidative stress analysis and apoptosis analysis through flow cytometry and fluorescent microscopy. The results showed concentration-dependent cytotoxicity of pulpotec cement extract to RAW 264.7 cells with an LC 50 of X/10-X/20. The computational analysis depicted the molecular interaction of pulpotec cement extract components with metabolic proteins like Sod1 and p53. The study revealed the effects of Pulpotec cement's extract, showing a concentration-dependent induction of oxidative stress and apoptosis. These effects were due to influential structural and functional abnormalities in the Sod1 and p53 proteins, caused by their molecular interaction with internalized components of Pulpotec cement. The study provided a detailed view on the utility of Pulpotec in endodontic applications, highlighting its biomedical aspects.

Desensitizing efficacy of a universal dentin adhesive containing mesoporous bioactive glass on dentin hypersensitivity: a randomized clinical trial with a split-mouth model.

This split-mouth blinded randomized controlled study compared the efficacy of a desensitizing agent with oxalate/resin polymer and a universal adhesive containing mesoporous bioactive glass (MBG) for dentin hypersensitivity (DH) relief, using Schiff sensitivity score (SSS) and visual analog scale (VAS). Split quadrants containing teeth with DH were treated with either MS Coat ONE or Hi-Bond Universal with MBG as the functional additive. Assessments at baseline, immediately post-application, and at 1- and 2-week follow-ups used standardized stimulus protocols (air, cold, and acid). The SSS difference was the primary outcome, while the VAS difference was the secondary outcome. A mixed linear effect model performed statistical analysis. Immediate DH reduction occurred in response to air stimuli, with a significant decrease in Group HB than in Group MS (p = 0.0178). Cold stimulus reduction exhibited a gradual cumulative effect, with consistently greater reductions in Group HB than in Group MS (p ≤ 0.0377). Both groups effectively managed acidic stimuli, with no significant differences (p > 0.05). The VAS scores decreased gradually over the follow-up period (p < 0.0001). This study highlights the differential efficacy of treatments for various DH triggers and recommends specific approaches based on different stimulus types. The universal adhesive containing MBG demonstrated DH relief potential, promising efficacy identical to or superior to that of a dedicated desensitizing agent. Further research exploring the long-term efficacy and underlying mechanisms is warranted. The universal adhesive containing MBG can be adopted as an in-office desensitizing agent for DH relief. The desensitizing efficacy of universal adhesive matches or surpasses dedicated agents for air and cold stimuli.

Efficacy of root-end filling techniques using premixed putty type bioceramic cements: an ex vivo study.

OBJECTIVES: Currently, premixed putty-type bioceramic cements (PPBCs) have become popular materials for root-end fillings. This study investigated three root-end filling techniques using PPBCs and calcium silicate-based sealers including EDTA pretreatment. MATERIALS AND METHODS: Ninety root segments were prepared and standardized with an artificial fin and lateral canal, and assigned to three groups (n = 30). Root-end fillings were placed using BC-RRM Putty alone (Group PA), injection of BC sealer followed by BC-RRM Putty (Lid Technique: Group LT) or BC-RRM Putty with BC sealer coating (Deep putty packing technique: Group DP). Half of each group was pretreated with 17% EDTA. The radiographic images of the specimens were assessed by five graders and push-out bond strength tests were conducted. The data were analyzed with a general linear model including two-way ANOVA and chi-square test at a significance level of 5%. RESULTS: DP approach demonstrated significantly higher bond strength than LT (P < 0.05). However, there was no statistically significant difference in bond strength between PA and either DP or LT. EDTA pretreatment had no significant effect on push-out bond strength. Radiographically, for the main canal, PA and DP scored significantly higher than LT. In the fin, PA scored significantly higher than others (P < 0.05). CONCLUSION: Our study highlights variations in root-end filling techniques. Injecting a bulk of bioceramic sealer before the placement of PPBCs may reduce bond strength and radiopacity. The application of PPBCs alone or in the deep putty technique demonstrates potential for favorable outcomes. EDTA pretreatment did not enhance bond-strength. CLINICAL RELEVANCE: Careful selection and application of bioceramic materials and techniques in root-end fillings may influence the outcome of endodontic root-end surgery. When PPBCs and calcium silicate-based sealers are used together for root-end fillings, sealer followed by deep putty application may offer improved bond strength and radiographic fill compared to the lid technique.

Preparation and performance evaluation of a novel orthodontic adhesive incorporating composite dimethylaminohexadecyl methacrylate-Polycaprolactone fibers.

This study addressed enamel demineralization, a common complication in fixed orthodontic treatment, by evaluating a novel orthodontic adhesive with DMAHDM-PCL composite fibers. These fibers, produced through electrospinning, were incorporated into orthodontic adhesive to create experimental formulations at different concentrations and a control group. The study assessed antimicrobial properties, biosafety, and mechanical characteristics. New orthodontic adhesive exhibited significant bacteriostatic effects, reducing bacterial biofilm activity and concentrations. Incorporating 1% and 3% DMAHDM-PCL did not affect cytocompatibility. Animal tests confirmed no inflammatory irritation. Shear bond strength and adhesive residual index results indicated that antimicrobial fibers didn't impact bonding ability. In conclusion, orthodontic adhesives with 3% DMAHDM-PCL fibers are potential antimicrobial bonding materials, offering a comprehensive solution to enamel demineralization in orthodontic patients.

Investigation of zinc polycarboxylate cement used in dental treatments in terms of retrospective dosimeter.

Zinc polycarboxylate cement is one of the few dental materials that demonstrate true adhesion to tooth structure. It is suitable for use in living organisms without causing harm. Its strong adhesion to teeth and low level of irritancy are two important parameters for the dental applications. In this study, the dosimetry properties of zinc polycarboxylate cement using thermoluminescence (TL) method were investigated and determined the effectiveness of its use as a good dosimeter. According to the results of this study, the sample shows a good TL properties with three main peaks found around 140°C, 220°C and 330°C. It has a wide linear dose response between 72 Gy and 2.3 kGy and good reusability of the TL peak found at 330°C. Unfortunately, the TL peak intensity values are rapidly faded within a short waiting time interval. Zinc polycarboxylate cement, which is frequently used in dental crowns, can be used as a retrospective dosimeter for measuring the amount of radiation in space studies and nuclear accidents due to its wide linear dose-response curve in the high dose region.

Bonding of Composite Cements Containing 10-MDP to Zirconia Ceramics Without Dedicated Ceramic Primer.

PURPOSE: To measure zirconia-to-zirconia microtensile bond strength (µTBS) using composite cements with and without primer. MATERIALS AND METHODS: Two Initial Zirconia UHT (GC) sticks (1.8x1.8x5.0 mm) were bonded using four cements with and without their respective manufacturer's primer/adhesive (G-CEM ONE [GOne] and G-Multi Primer, GC; Panavia V5 [Pv5]), and Panavia SA Cement Universal [PSAu], and Clearfil Ceramic Plus, Kuraray Noritake; RelyX Universal (RXu) and Scotchbond Universal Plus [SBUp], 3M Oral Care). Specimens were trimmed to an hour-glass shaped specimen whose isthmus is circular in cross-section. After 1-week water storage, the specimens were either tested immediately (1-week µTBS) or first subjected to 50,000 thermocycles (50kTC-aged µTBS). The fracture mode was categorized as either adhesive interfacial failure, cohesive failure in composite cement, or mixed failure, followed by SEM fracture analysis of selected specimens. Data were analyzed using linear mixed-effects statistics (α = 0.05; variables: composite cement, primer/adhesive application, aging). RESULTS: The statistical analysis revealed no significant differences with aging (p = 0.3662). No significant difference in µTBS with/without primer and aging was recorded for GOne and PSAu. A significantly higher µTBS was recorded for Pv5 and RXu when applied with their respective primer/adhesive. Comparing the four composite cements when they were applied in the manner that resulted in their best performance, a significant difference in 50kTC-aged µTBS was found for PSAu compared to Pv5 and RXu. A significant decrease in µTBS upon 50kTC aging was only recorded for RXu in combination with SBUp. CONCLUSION: Adequate bonding to zirconia requires the functional monomer 10-MDP either contained in the composite cement, in which case a separate 10-MDP primer is no longer needed, or in the separately applied primer/adhesive.

Effects of 3D-Printing Technology and Cement Type on the Fracture Resistance of Permanent Resin Crowns for Primary Teeth.

PURPOSE: To evaluate the fracture resistance of permanent resin crowns for primary teeth produced using two different 3D-printing technologies (digital light processing [DLP] and stereolithography [SLA]) and cemented with various luting cements (glass ionomer, resin-modified glass ionomer, and self-adhesive resin cement), whether thermally aged or not. MATERIALS AND METHODS: A typodont primary mandibular second molar tooth was prepared and scanned, and a restoration design was created with web-based artificial intelligence (AI) dental software. A total of 96 crowns were prepared, and 12 experimental groups were generated according to the cement type, 3Dprinting technology (DLP or SLA), and thermal aging. Fracture resistance values and failure types of the specimens were noted. The results were statistically analyzed with three-way ANOVA and Tukey HSD tests (α = .05). RESULTS: The results of the three-way ANOVA showed that there was an interaction among the factors (3D-printing technology, cement type, and thermal aging) (P = .003). Thermal aging significantly decreased the fracture resistance values in all experimental groups. DLP-printed crowns showed higher fracture resistance values than SLA-printed crowns. Cement type also affected the fracture resistance, with glass ionomer cement showing the lowest values after aging. Resin-modified glass ionomer and resin cements were more preferable for 3D-printed crowns. CONCLUSIONS: The type of cement and the 3D-printing technology significantly influenced the fracture resistance of 3D-printed permanent resin crowns for primary teeth, and it was decided that these crowns would be able to withstand masticatory forces in children.