Laboratory study of fracture resistance and failure mode of porcelain laminate veneers with different preparation depths in endodontically treated teeth.

PURPOSE: To compare the fracture resistance and failure mode of porcelain laminate veneers with different preparation depths in endodontically treated teeth. METHODS: Root canal treatment was performed for 40 maxillary central incisors, and then the teeth were divided into four groups (n= 10). The preparation depths were as follows: Group A: 0.9 mm, Group B: 0.6 mm, Group C: 0.3 mm, and in all three groups, 2 mm butt joint incisal reductions were performed; Group D was a control group with no preparation. Then 30 lithium disilicate porcelain veneers were milled by CAD- CAM method and cemented. After that, all specimens were subjected to cyclic loading and thermal cycling and finally were tested by a universal testing machine until failure occurred. RESULTS: The mean failure loads (N) after exposure to continuous load were as follows: Group A: 625.70 (401.45-1037.77), Group B: 780.32 (222.93-1391.82), Group C: 748.81 (239.68-1241.87) and Group D (control) : 509.88 (84.42-1025.85) and P= 0.216. Analysis of failure mode in four groups showed that P= 0.469. There was no significant difference between the control and the other groups. In this study, 0.3, 0.6 and 0.9 mm depths of preparation for porcelain laminate veneers for endodontically treated teeth had no significant difference in fracture resistance and failure mode with non-prepared teeth. CLINICAL SIGNIFICANCE: Reasonable consideration might be given to porcelain laminate veneer treatment for teeth that have become discolored and resistant to bleaching (such as instances where discoloration is severe following root canal treatment). This approach is considered to be on the conservative side, and has demonstrated that a labial preparation depth reduction of up to 0.9 mm does not have any impact on the failure mode or fracture resistance of endodontically-treated teeth.

Therapeutic solutions for discoloration of calcified teeth based on CBCT diagnosis.

Single tooth orange discoloration secondary to root canal calcification occurs as a consequence of dental trauma, orthodontic treatment, or for unknown rea- sons. A correct case history must be compiled and a CBCT study carried out in order to establish the diag- nosis and define the best treatment plan in each case. The aim of the present study was to offer a therapeutic protocol involving a clinical decision-making tree dia- gram based on the presence or absence of apical dis- ease and the degree of canal calcification. Dental bleaching and the use of ceramic veneers allow es- thetic restoration in such cases.

Advanced digital planning approach using a 3D-printed mock-up. A case report.

OBJECTIVE: A diagnostic mock-up is a key tool that allows a preview of the outcome of an esthetic restoration. With recent developments in CAD/CAM technology, it is important to understand the pros and cons of chairside digital dentistry and the restorative materials used. The aim of the present case report is to describe in detail the use of a 3D-printed mock-up fabricated from a polymer-based material for an esthetic treatment plan within a fully digital workflow. CASE REPORT: A 45-year-old female patient presented at the clinic concerned about her esthetic appearance and the color of her anterior incisors. After a conclusive diagnosis, a restoration was planned using ceramic veneers from maxillary premolar to premolar. For a preview visualization of the outcome, an intraoral scanner was used to obtain 3D images and to allow the design of a digital smile. The template STL file was exported to a 3D printer and a 0.6-mm mock-up in A3-shade 3D resin was produced after 25 min. The mock-up was tested through a try-in and approved by the patient. As a result, the printed mock-up was considered predictable and reliable for the final restoration. CONCLUSIONS: The ease, speed, and reduced costs derived from the digital workflow, in conjunction with the accuracy of the mock-up, made the procedure highly efficient and recommendable.

Effect of surface treatment and resin cement type on the bond strength of polyetheretherketone to lithium disilicate ceramic.

BACKGROUND: This study aims to evaluate the effect of surface treatment and resin cement on the shear bond strength (SBS) and mode of failure of polyetheretherketone (PEEK) to lithium disilicate ceramic (LDC). This is suggested to study alternative veneering of PEEK frameworks with a ceramic material. METHODS: eighty discs were prepared from PEEK blank and from lithium disilicate ceramic. Samples were divided into four groups according to surface treatment: Group (A) air abraded with 110 µm Al2O3, Group (AP) air abrasion and primer application, Group (S) 98% sulfuric acid etching for 60 s, Group (SP) Sulfuric acid and primer. Each group was subdivided into two subgroups based on resin cement type used for bonding LDC:1) subgroup (L) self- adhesive resin cement and 2) subgroup (B) conventional resin cement (n = 10). Thermocycling was done for all samples. The bond strength was assessed using the shear bond strength test (SBS). Failure mode analysis was done at 50X magnification with a stereomicroscope. Samples were chosen from each group for scanning electron microscope (SEM). The three-way nested ANOVA followed by Tukey's post hoc test were used for statistical analysis of results. Comparisons of effects were done utilizing one way ANOVA and (p < 0.05). RESULTS: The highest mean of shear bond strength values was demonstrated in Group of air abrasion with primer application using conventional resin cement (APB) (12.21 ± 2.14 MPa). Sulfuric acid groups showed lower shear bond strength values and the majority failed in thermocycling especially when no primer was applied. The failure mode analysis showed that the predominant failure type was adhesive failure between cement and PEEK, while the remaining was mixed failure between cement and PEEK. CONCLUSION: The air abrasion followed by primer application and conventional resin cement used for bonding Lithium Disilicate to PEEK achieved the best bond strength. Primer application did not have an effect when self-adhesive resin cement was used in air-abraded groups. Priming step is mandatory whenever sulfuric acid etching surface treatment is utilized for PEEK.

Tetracycline staining of the dentition: a review of the literature and report of a clinical case.

The present article reviews the literature regarding tetracycline staining of the dentition and its esthetic management. A total of 49 articles were identified in the initial search, and 22 articles met the eligibility criteria of this narrative literature review. Tetracycline staining results from its use in children between the ages of 6 months and 6 years, when tooth crowns are formed; the effects are dependent on the dosage, duration of treatment, stage of tooth mineralization, and activity of the mineralization process. Tooth bleaching is always the first treatment option for low-grade cases of tetracycline staining. Restorative procedures are indicated for severe staining. The article also describes the treatment of severe staining affecting the maxillary anterior dentition of a 48-year-old man who reported the systemic administration of tetracycline during childhood. Direct composite resin laminate veneers were proposed to achieve immediate, highly esthetic restorations. A combination of different resinous materials in different shades was applied to meet the needs of the patient. The use of direct composite resin laminate veneers satisfied the functional and esthetic demands of the patient at a lower cost than ceramic materials.

Evaluation of bond strength between zirconia milled ceramic material and veneered dental porcelain.

This study aimed at examining the bond strength between zirconia and ceramic veneer, following the ISO 9693 guidelines. A total of fifty specimens of zirconia/ceramic-veneer system were produced using two commercial zirconias (VITA YZ-HTWhite and Zolid HT+ White, referred to as Group A and Group B, respectively) and a ceramic-veneering material (Zirkonia 750). The microstructure (via x-ray diffraction analysis, XRD and Secondary Electron mode, SEM) and the mechanical properties (via 3-point bending tests) of the two groups were assessed. Then, experiments were conducted according to the ISO 9693 and conventional protocols applied for producing zirconia/ceramic-veneer restorations. Bond strength values, measured by 3-point bending tests, were 34.42 ± 7.60 MPa for Group A and 31.92 ± 6.95 MPa for Group B. SEM observations of the cohesively fractured surfaces (on the porcelain side) and the examination for normality using the Shapiro-Wilk test suggested the use of Weibull statistical analysis. Median strength (σ50%) for Group A and Group B was 34.76 and 32.22 MPa, while the characteristic strength (σ63.2%) was 35.78 and 33.14 MPa, respectively. The Weibull modulus disparity between groups (12.69 and 13.07) was not significant. Bond strength exceeded the ISO 9693 minimum of 20 MPa, suggesting satisfactory strength for clinical use.

A comparative evaluation of the variations on the shades of pressable ceramic system with the layering technique after different number of firing cycles: An in vitro study.

AIM: The main aim of the present study was to compare and evaluate the effect of repetitive firings on different shades of a pressable all ceramic system layered with veneering porcelain. SETTING AND DESIGN: In-vitro comparative study. MATERIALS AND METHODS: An in vitro comparative study was conducted, and a total of 60 disc shaped specimens (15 mm in diameter and 0.8 mm in thickness) were made of heat pressed ceramic of shades A2, A3, and B2 (20 discs of each shade) grouped as Group I, II, and III, respectively, using the lost wax technique. The discs were subsequently layered with veneering porcelain followed by glazing and overglazing and underwent a firing cycle at each step until six times combined. CIE L*a*b* measurements were noted on each sample after the third, fourth, fifth, and sixth firing using VITA Easyshade Advance 4.0 spectrophotometer. STATISTICAL ANALYSIS USED: Statistical Analysis was done by SPSS 17.0 software. One way analysis of variance, multiple comparisons using the Tukey test, and descriptive statistical analysis were done for all the groups in the study. P <0.05 was statistically significant. RESULTS: The mean color differences for the repeated firings were imperceptible (ΔE <1.67) to the human eye for all ceramic samples tested except between the fourth and fifth firing of Group II (shade A3). CONCLUSION: The analysis revealed that although repeated firings lead to changes in L*, a*, and b* values, the mean color difference was below the clinically acceptable color change (ΔE <3.7).

Enamel Veneer Rehabilitation of a Premolar to an Incisor After Autotransplantation.

Tooth autotransplantation is one of the methods used for tooth loss rehabilitation in children. Premolars are usually used as autotransplants requiring esthetic alterations. The purpose of this paper is to present an innovative, alternative and inexpensive way to restore auto-transplanted teeth using the crown of the tooth of the recipient site. A seven-year-old male with a non-contributory medical history presented with an intrusion of his permanent maxillary right central incisor. The tooth underwent orthodontic extrusion using fixed appliances but eventually showed signs of ankylosis. At 10 years old, autotransplantation of a premolar to substitute the ankylosed incisor was undertaken. Six weeks after the autotransplantation, the premolar was restored to an incisor by modifying the extracted ankylosed tooth to a veneer for the transplanted tooth, providing functional and esthetic restoration. The patient has been followed up for two years without any complications. This technique can help clinicians restore autotransplants in an easy and esthetic manner.

Clinical outcomes of self-glazed zirconia veneers produced by 3D gel deposition: a retrospective study.

BACKGROUND: Self-glazed zirconia (SZ) restorations are made by a novel additive three-dimensional gel deposition approach, which are suitable for a straightforward completely digital workflow. SZ has recently been used as minimally invasive veneer, but its clinical outcomes have not been clarified yet. This study aimed to evaluate the preliminary clinical outcomes of SZ veneers compared with the widely used lithium disilicate glass-ceramic veneers made by either pressing (PG) or milling (MG) process. METHODS: Fifty-six patients treated with SZ, PG, and MG veneers by 2 specialists between June 2018 and October 2022 were identified. Patients were recalled for follow-up at least 1 year after restoration. Clinical outcomes were assessed by 2 independent evaluators according to the modified United States Public Health Service (USPHS) criteria. Overall patient satisfaction was assessed using visual analogue scale (VAS), and analyzed by one-way ANOVA. Chi-square test was applied to compare the difference in the success and survival rates among the 3 groups. RESULTS: A total of 51 patients restored with 45 SZ, 40 PG, and 41 MG veneers completed the study, with a patient dropout rate of 8.9%. Mean and standard deviation of follow-up period was 35.0 ± 14.7 months. All restorations performed well at baseline, except for 2 SZ veneers with mismatched color (rated Bravo). During follow-up, marginal discrepancy (rated Bravo) was found in 4 MG veneers and 1 PG veneer, and partially fractured (rated Charlie) was found in another 2 PG veneers. The survival rate of SZ, PG, and MG veneers was 100%, 95%, and 100%, with a success rate of 95.56%, 92.50%, and 90.24%, respectively, none of which were significantly different (p = 0.099 and 0.628, respectively). The mean VAS score of SZ, PG, and MG was 95.00 ± 1.57, 93.93 ± 2.40, and 94.89 ± 2.00 respectively, without significant difference (p > 0.05). CONCLUSION: SZ veneers exhibited comparable preliminary clinical outcomes to PG and MG veneers, which could be considered as a feasible option for minimally invasive restorative treatment.

Fabrication trueness and marginal quality of additively manufactured resin-based definitive laminate veneers with different restoration thicknesses.

OBJECTIVES: To evaluate how restoration thickness (0.5 mm and 0.7 mm) affects the fabrication trueness of additively manufactured definitive resin-based laminate veneers, and to analyze the effect of restoration thickness and margin location on margin quality. METHODS: Two maxillary central incisors were prepared either for a 0.5 mm- or 0.7 mm-thick laminate veneer. After acquiring the partial-arch scans of each preparation, laminate veneers were designed and stored as reference data. By using these reference data, a total of 30 resin-based laminate veneers were additively manufactured (n = 15 per thickness). All veneers were digitized and stored as test data. The reference and test data were superimposed to calculate the root mean square values at overall, external, intaglio, and marginal surfaces. The margin quality at labial, incisal, mesial, and distal surfaces was evaluated. Fabrication trueness at each surface was analyzed with independent t-tests, while 2-way analysis of variance was used to analyze the effect of thickness and margin location on margin quality (α = 0.05). RESULTS: Regardless of the evaluated surface, 0.7 mm-thick veneers had lower deviations (P < 0.001). Only the margin location (P < 0.001) affected the margin quality as labial margins had the lowest quality (P < 0.001). CONCLUSION: Restoration thickness affected the fabrication trueness of resin-based laminate veneers as 0.7 mm-thick veneers had significantly higher trueness. However, restoration thickness did not affect the margin quality and labial margins had the lowest quality. CLINICAL SIGNIFICANCE: Laminate veneers fabricated by using tested urethane-based acrylic resin may require less adjustment when fabricated in 0.7 mm thickness. However, marginal integrity issues may be encountered at the labial surface.

Accuracy of the intaglio surface of 3D-printed hybrid resin-ceramic crowns, veneers and table-tops: An in vitro study.

OBJECTIVES: The present study aims to examine the influence of the build angle on the accuracy (trueness and precision) of 3D printed crowns, table-tops and veneers with a hybrid resin-ceramic material. METHODS: One crown, on table-top and one veneer were printed in five different build angles (0°, 30°, 45°, 60°, 90°) (n = 50) with the digital light processing (DLP) system (Varseo XS, Bego) using hybrid resin (Varseo Smile Crownplus A3, Bego). All printed restorations were scanned using the laboratory scanner (D2000, 3Shape) and matched onto the initial reference design in metrology software (Geomagic Control X, 3D Systems). The root mean square error (RMSE) was calculated between the scanned and reference data. The data was statistically analyzed using the Tukey multiple comparison test and Wilcoxon multiple comparison test. RESULTS: The crown group showed higher trueness at 30° (0.021 ± 0.002) and 45° (0.020 ± 0.002), and table-tops at 0° (0.015 ± 0.001) and 30° (0.014 ± 0.001) (p < 0.0001). Veneers demonstrated higher trueness at 30° (0.016 ± 0.002) (p < 0.0001). All three restoration types demonstrated the lowest trueness at a 90° build angle and portrayed deviations along the z axis. The veneer and table-top groups showed the lowest precision at 90° (veneers: 0.021 ± 0.008; table-tops: 0.013 ± 0.003). The crown group portrayed the lowest precision at 45° (0.017 ± 0.005) (p < 0.0001). CONCLUSION: The build angle of DLP-printed hybrid resin-ceramic restorations influences their accuracy. CLINICAL SIGNIFICANCE: Considering the build angle is important to achieve a better accuracy of 3D-printed resin-ceramic hybrid restorations. This may help predict or avoid the interference points between a restoration and a die and minimize the clinical adjustments.

Componeer as an aesthetic treatment option for anterior teeth: a case report.

INTRODUCTION: Structural abnormalities or anomalies in the anterior teeth, also known as the aesthetic zone, are an important problem for patients and a challenge for dentists. Structural abnormalities or tooth anomalies can change in color, shape, and function. Most dentists prefer minimally invasive aesthetic treatment. One of the aesthetic treatment options for anterior teeth is veneers. Veneer is a restoration that covers the labial part of the tooth with a thin layer of material to correct abnormalities in the color, shape, or function of the tooth. Veneer restoration can be done indirectly with porcelain material made in a laboratory and directly with composite material on the tooth surface or prefabricated which is available from the factory. Componeer is a prefabricated composite veneer that combines the aesthetic properties of ceramic veneers and the adhesive ability of composite veneers to the tooth structure. This case report describes the treatment of two central incisors that had been filled with composite and peg shapes on both lateral incisors using a componeer. CASE REPORT: A 32-year-old female patient came to the Dental Conservation Clinic at Dentistry Hospital, Padjadjaran University with the main complaint of her right and left upper front teeth and wanted to repair her old fillings and close the gap between her right and left upper front teeth and her canine teeth. Clinical examination showed that teeth 11 and 21 had been filled with composite which had changed color and had an inharmonious shape as well as a gap between the upper front teeth on the right and left sides and the right and left canine teeth. TREATMENT: The maxilla and mandibular teeth are molded for study models and working models. In the working model, a wax-up is carried out, then a mock-up on the patient's teeth. Next, choose the color and size of the components that match the mock up results. Teeth 11 and 21 had their old composite fillings cleaned and refilled with dentin colored composite, teeth 13, 12, 11, 21, 22, and 23 were prepared with a minimum thickness of 0.3 mm to make room for the componeer material. The teeth was etched and bonded, and bonding was applied to the inner surface of the componeer. The composite is placed on the inner surface of the componeer then placed on the labial surface of the tooth and pressed with a special tool, then light cured. The final step is polishing. TREATMENT RESULTS: Teeth 13, 12, 11, 21, 22, and 23 which had undergone veneer treatment using componeer, were controlled after 1 week of treatment. The patient did not complain about the results of the treatment and said he was satisfied with the treatment.

Preparation of ultrathin translucent zirconia laminate veneers using 3D printing reduction guides.

Minimizing and controlling the amount of tooth reduction during the preparation of ultrathin laminate veneers is a challenge for minimally invasive dentistry. The use of reduction guides is advised to reach the optimal space required for the definitive restoration without excessive reduction. The digital production of a reduction guide used to control tooth preparation for ultrathin laminate veneers is described.

Prognostic factors associated with pulp status in patients with cracked teeth treated with occlusal veneer: A 6- through 24-month prospective clinical study.

BACKGROUND: The authors evaluated the prognostic factors associated with pulp status in patients with cracked teeth (CT) treated with occlusal veneer. METHODS: An analysis of 80 CT (71 patients) with 1 or more crack lines (CLs) and normal pulp vitality or reversible pulpitis was performed. All patients received occlusal veneer and their demographic and clinical data were recorded. Pulp status and clinical features were recorded at 1 week and posttreatment at 1, 2, 3, 6, 12, 18, and 24 months. RESULTS: Maxillary first molars were commonly involved (30 [38%]). The number of CLs on the finish line ranged from 1 through 7 and most had 3 CLs (24 [30%]). The number of CLs through preparation on the finish line ranged from 0 through 4, and 2 CLs (42 [53%]) were the most prevalent. During follow-up, 5 of 80 CT progressed to pulp disease, resulting in a success rate of 93.8%. Results of the Cox model and Kaplan-Meier analysis showed that probing depth greater than 6 mm, widening periodontal ligament of apical area, more than 4 CLs on finish line, and more than 2 CLs through preparation on the finish line were risk factors associated with pulp status (P < .05). CONCLUSIONS: Occlusal veneer can protect CT without preventive root canal therapy. PRACTICAL IMPLICATIONS: The success rate and risk factors of pulp disease in CT restored with occlusal veneer are reported.

Fracture Resistance and Failure Mode of Monolithic Zirconia, Veneered Zirconia, and Metal-Ceramic Full-Coverage Restorations: A Comparative In Vitro Study.

PURPOSE: To evaluate and compare the fracture mode and strength of monolithic zirconia to veneered zirconia and metal-ceramic full-coverage restorations following artificial aging and to test the performance of translucent zirconia in terms of load-bearing capacity. MATERIALS AND METHODS: Two mandibular first molars were prepared and scanned for their respective groups of full-coverage restorations. A total of 75 full-coverage restorations were fabricated and divided into five groups: two groups for monolithic zirconia, two groups for veneered zirconia, and one group for metal-ceramic. Then, 75 light-cured hybrid composite resin dies were fabricated to serve as abutments. Before cementation, all full-coverage restorations were subjected to accelerated aging. After cementation, all full-coverage restorations were subjected to compressive loading until fracture in an electromechanical universal testing machine. A two-way nested ANOVA and Tukey test were used to analyze the results with 95% confidence levels. RESULTS: Monolithic zirconia full-coverage restorations showed the highest mean fracture resistance of 4,201.0 N, followed by metalceramic full-coverage restorations of 3,609.3 N, and veneered zirconia full-coverage restorations showed the lowest mean fracture resistance of 2,524.6 N. The main mode of failure was cohesive bulk fracture for the monolithic zirconia group, cohesive/adhesive failure with infrastructure damage for the veneered zirconia group, and cohesive/adhesive failure without infrastructure damage for the metal-ceramic group. CONCLUSIONS: Monolithic zirconia full-coverage restorations showed superior resistance to fracture compared to metal-ceramic full-coverage restorations and are highly reliable in terms of load-bearing capacity within the posterior regions of the mouth.

Fracture strength of porcelain veneer on surface-treated zirconia.

In this study, we investigated the effects of surface treatment on the fracture strength of porcelain-veneered zirconia. Highly translucent 4 mol% yttria-stabilized zirconia disks (KATANA HT, Kuraray Noritake Dental) were divided into three surface-treatment groups: 1)as-sintered, 2) alumina sandblasted, and 3) ground. Crystallographic and surface-roughness analyses were conducted for each group. Veneering ceramics (Cerabien ZR, Kuraray Noritake Dental) were applied to the zirconia surfaces. The fracture strengths of the porcelain-veneered zirconia disks were measured using biaxial flexural-strength tests. Crystallographic analysis revealed that grinding and sandblasting increased the fractions of the monoclinic and rhombohedral zirconia phases. The ground specimens had a higher surface roughness than the sandblasted specimens. Weibull analysis showed no significant differences in biaxial flexural strength among the three groups. The results suggest that these surface treatments do not affect the fracture strength of porcelain-veneered zirconia.

Evaluation of marginal and internal adaptation of veneers generated by the guided prosthetic tooth preparation system.

OBJECTIVE: This in vitro study aimed to assess and contrast the marginal and internal adaptation of all-ceramic prefabricated veneers manufactured via the FirstFit guided tooth preparation system against all-ceramic veneers produced using the chairside Computer-Aided Design/Computer Aided Manufacture (CAD/CAM) system following identical guided preparation protocols. MATERIALS AND METHODS: Two main groups were included, with 16 lithium disilicate veneers per group. Four typodonts were used for the test (FirstFit) and control CAD/CAM groups. Intraoral scans created master casts and preparation guides. Guides performed preparations on typodont teeth (two central incisors and two lateral incisors). Prepared teeth were scanned (CEREC Omnicam) to design and mill CAD/CAM veneers. Marginal gap thickness and cement space thickness were measured using light microscopy at four locations: marginal, cervical internal, middle internal, and incisal internal. RESULTS: No significant difference existed between groups for marginal adaptation (p = 0.058) or incisal internal adaptation (p = 0.076). The control group had significantly lower values for middle internal adaptation (p = 0.023) and cervical internal adaptation (p = 0.019). CONCLUSIONS: Guided preparation evaluation showed no significant differences in marginal or incisal internal adaptation. The CAD/CAM group had significantly lower middle and cervical internal adaptation values.

Extended porcelain veneers in the maxillary anterior region. A retrospective study with an up to 27-year follow-up

AIM: The aim of the present retrospective study was to evaluate the long-term results, including technical and biologic outcomes, of maxillary extended porcelain veneers with an incisal edge thickness above 2 mm. MATERIALS AND METHODS: Patients treated with extended porcelain veneers performed by a single clinician at University of Geneva between 1990 and 2003 were identified and invited to an examination. Of the 37 identified patients, 10 patients with 50 veneers agreed to be examined and were included. A clinical examination was performed to assess survival rates as well as technical and biologic outcomes (modified United States Public Health Services criteria). Patient records were also reviewed to retrieve patient and reconstruction data and every complication event. Patient-reported outcome measures (PROMs) were evaluated using a visual analog scale to measure esthetic satisfaction, functional and phonetic comfort, masticatory improvement, tooth sensitivity, and acceptance of restoration replacement in case of failure. Data were descriptively analyzed, and Kaplan-Meier survival estimators were computed for survival rates and complication events. RESULTS: The survival rate of the veneers was 96% after a mean follow-up of 20.7 ± 3.7 years in function. The technical complication rate amounted to 30%, including two failures, nine repairable fractures, three cracks, and one displacement due to trauma. No cavitated caries lesions or endodontic complications were registered. PROMs were very high for esthetic satisfaction and phonetic comfort. CONCLUSIONS: Within the limitations of the present retrospective study, extended porcelain veneers appear to be a successful long-term treatment option in terms of clinical outcomes and patient satisfaction.