Effect of toothbrushing with conventional and whitening dentifrices on monolithic zirconia after finishing procedures.

PURPOSE: To evaluate the effect of toothbrushing with conventional and whitening dentifrices on the color difference (ΔE00), gloss (Δgloss), and surface roughness (SR) of stained stabilized zirconia with 5 mol% of yttrium oxide (5Y-TZP) after polishing or glazing. METHODS: Specimens were divided into four groups (n=20): C (control), S (staining), SG (staining and glazing) and SP (staining and polishing). 50,000 toothbrushing cycles were performed with conventional (n=10) and whitening (n= 10) dentifrice slurries. The ΔE00 and Δgloss were measured using a spectrophotometer and CIEDE2000 system while SR was measured by laser confocal microscope. The ΔE00 and Δgloss data were analyzed using 2-way ANOVA, and SR data were analyzed using the linear repeated measures model, with Bonferroni's complementary test (α= 0.05). RESULTS: The ΔE00 values were beyond the acceptability threshold and no differences were found among the groups. There was no difference among groups to Δgloss after toothbrushing with conventional dentifrice while SP presented the highest values of Δgloss after toothbrushing with whitening dentifrice. Conventional dentifrice decreased the SR of stained groups and whitening dentifrice decreased SR of S and SG. The toothbrushing with conventional and whitening dentifrices promoted color difference, but did not impair gloss and surface roughness of stained 5Y-TZP. CLINICAL SIGNIFICANCE: Monolithic zirconia has been routinely used for esthetic restorations, however the type of finishing procedures that is carried out on it must be taken into consideration, in addition to the fact that brushing can influence the color difference of the material as well as interfere with surface roughness and gloss.

Non-invasive prediction of maca powder adulteration using a pocket-sized spectrophotometer and machine learning techniques.

Discriminating different cultivars of maca powder (MP) and detecting their authenticity after adulteration with potent adulterants such as maize and soy flour is a challenge that has not been studied with non-invasive techniques such as near infrared spectroscopy (NIRS). This study developed models to rapidly classify and predict 0, 10, 20, 30, 40, and 50% w/w of soybean and maize flour in red, black and yellow maca cultivars using a handheld spectrophotometer and chemometrics. Soy and maize adulteration of yellow MP was classified with better accuracy than in red MP, suggesting that red MP may be a more susceptible target for adulteration. Soy flour was discovered to be a more potent adulterant compared to maize flour. Using 18 different pretreatments, MP could be authenticated with R2CV in the range 0.91-0.95, RMSECV 6.81-9.16 g/,100 g and RPD 3.45-4.60. The results show the potential of NIRS for monitoring Maca quality.

Reliability of the color measurement of resin composites using images obtained using a stereoscopic loupe.

This study assessed the reliability of a color measurement method using images obtained from a charge-coupled device (CCD) camera and a stereoscopic loupe. Disc-shaped specimens were created using the composite Filtek Z350 XT (shades DA1, DA2, DA3, and DA4) (n = 3). CIELAB color coordinates of the specimens were measured using the spectrophotometer SP60 over white and black backgrounds. Images of the same specimens were taken using a CCD camera attached to a stereoscopic loupe. The color of the image was measured (red-green-blue [RGB]) using an image processing software and converted to CIELAB coordinates. For each color coordinate, data from images were adjusted using linear regressions predicting those values from SP60. The whiteness index for dentistry (WID) and translucency parameter (TP00) of the specimens as well as the color differences (ΔE00) among pairwise shades were calculated. Data were analyzed via repeated-measures analysis of variance and Tukey's post hoc test (α = 0.05). Images obtained using the loupe tended to be darker and redder than the actual color. Data adjustment resulted in similar WID, ΔE00, and TP00 values to those observed for the spectrophotometer. Differences were observed only for the WID of shade DA3 and ΔE00 for comparing DA1 and DA3 over the black background. However, these differences were not clinically relevant. The use of adjusted data from images taken using a stereoscopic loupe is considered a feasible method for color measurement.

Comparison of the Friedewald and Vujovic methods with the calculated LDL concentration in a biochemical auto-analyzer.

Objective: To compare the concentration of Low-Density Lipoprotein (LDL-c) obtained using the Friedewald formula with those obtained directly with the RAYTO CHEMRAY 120 autoanalyzer. Methods: Cross-sectional study. We evaluated outpatients with a medical request for a lipid profile study (total cholesterol, triglycerides, LDL, and HDL). The analyses were carried out in a RAYTO CHEMRAY 120 autoanalyzer under the principle of spectrophotometry. We obtained LDL-c using the Friedewald and Vujovic formulas. Results: We evaluated 199 individuals whose direct LDL concentration averages were measured by the RAYTO CHEMRAY 120 equipment. Those calculated by the Friedewald and Vujovic formulas were 129.97 ± 32.66, 119.28 ± 30.44, and 127.01 ± 32.01, respectively, and in all cases, significant differences (P < 0.001) were observed with the RAYTO analyzer. In both cases a low positive bias was found with the RAYTO analyzer.. The Passing-Bablok and Deming's regressions showed a linear correlation between both methods (Friedewald and Vujovic) with the LDL values obtained with the Rayto autoanalyzer. Conclusions: Our study found that the Friedewald and Vujovic methods are good predictors of LDL cholesterol levels and have a low level of bias. Therefore, they could be used as potential predictors.

Objetivo: Comparar las concentraciones de Lipoproteínas de Baja Densidad (LDL-c) obtenidas mediante la fórmula de Friedewald con las obtenidas directamente con el autoanalizador RAYTO CHEMRAY 120. Métodos: Estudio transversal. Se evaluaron pacientes ambulatorios con solicitud médica de perfil lipídico (colesterol total, triglicéridos, LDL y HDL). Los análisis se realizaron con un autoanalizador RAYTO CHEMRAY 120 bajo el principio de espectrofotometría. Obtuvimos el LDL-c usando las fórmulas de Friedewald y Vujovic. Resultados: Se evaluaron 199 individuos cuyos promedios directos de concentración de LDL fueron medidos con el equipo RAYTO CHEMRAY 120. Las concentraciones calculadas por las fórmulas de Friedewald y Vujovic fueron de 129,97 ± 32,66, 119,28 ± 30,44, y de 127,01 ± 32,01, respectivamente, y en todos los casos se observaron diferencias significativas (P < 0,001) con el analizador RAYTO. En ambos casos se encontró un sesgo positivo bajo en el analizador RAYTO. Las regresiones de Passing-Bablok y Deming mostraron una correlación lineal entre ambos métodos (Friedewald y Vujovic) con los valores de LDL obtenidos con el autoanalizador Rayto. Conclusión: Nuestro estudio encontro que los métodos de Friedewald y Vujovic son buenos predictores de los niveles de colesterol LDL y presentan un nivel de sesgo bajo. Por lo que podrían usarse como potenciales predictores.

Color Stability of Bioactive Restorative Material vs Nanohybrid Resin Composite: An In Vitro Study.

AIM: This study aimed to assess the color stability of bioactive restorative materials vs nanohybrid resin composites after 3 months of immersion in three frequently consumed beverages. MATERIALS AND METHODS: Thirty disk-shaped specimens of Giomer dental restorative material (Shofu, Japan) and nanohybrid resin composite (Tokuyama, Japan) were performed using a Teflon mold. Super-Snap system (Shofu, Japan) was utilized to finish and polish the specimens to be preserved for 24 hours in distilled water at 37°C. The samples had been divided into three subgroups (Coffee, tea, Pepsi) (n = 5). The initially displayed color measurements of the samples were performed using a spectrophotometer (VITA Easyshade® V). After 7 days, 30 days, and 90 days, color measurements were repeated, and the E of each sample was estimated. E of each sample was calculated. RESULTS: The Giomer group showed statistically significant higher E values than the nanohybrid resin composite where the p-value was ≤0.0001. Tea subgroup showed the highest statistically significant E values in both groups where the p-value was ≤ 0.0001. The highest statistically significant color change was recorded at 3 months. CONCLUSION: The color of bioactive restorative material is less stable if compared with nanohybrid resin composite. CLINICAL SIGNIFICANCE: As tea and coffee are popular beverages, particularly in Middle Eastern nations, dentists must advise patients about the color change of resin restorations. Patients are advised to brush their teeth immediately after consuming these beverages. How to cite this article: Saber EH, Abielhassan MH, Abed YA, et al. Color Stability of Bioactive Restorative Material vs Nanohybrid Resin Composite: An In Vitro Study. J Contemp Dent Pract 2024;25(3):221-225.

Bleaching efficacy of in-office dental bleaching with different application protocols: a single-blind randomized controlled trial.

OBJECTIVE: This randomized controlled trial aimed to evaluate the equivalence in the color change, adverse effects, self-perception (AS) and the impact on oral condition (IO) of participants submitted to different application protocols of in-office dental bleaching. MATERIALS AND METHODS: 165 participants were bleached with a 35% hydrogen peroxide gel (Total Blanc Office One-Step, DFL), according to the following protocols: (1) 2 applications of 20-min each (2 × 20 min); (2) 1 × 40-min and; (3) 1 × 30-min. The color change was evaluated with the Vita Easyshade spectrophotometer, Vita Classical and Vita Bleachedguide scales. The intensity and risk of tooth sensitivity (TS) and gingival irritation (GI) were recorded using a 0-10 visual analogue scale (VAS). AS and IO was assessed before and after the bleaching procedure using the Orofacial Aesthetic Scale and Oral Health Impact Profile-14, respectively. RESULTS: Equivalent color change were observed (p < 0.001), with no significant difference between groups. The group 2 × 20 min presented the highest risk of TS (76%, 95% CI 63 to 85), compared to the 1 × 30 min (p < 0.04). The intensity of TS and GI and the risk of GI was similar between groups (p > 0.31). Irrespectively of the group (p = 0.32), significant improvements were observed for all items of AS and IO after bleaching (p < 0.02). CONCLUSIONS: The 1 × 30 min protocol produced equivalent color change to the other bleaching protocols with reduced risk of TS and shorter application time. CLINICAL RELEVANCE: A more simplified application regimen of a single application of 30 min yields effective bleaching and patient satisfaction while minimizing undesirable side effects and improving patient satisfaction.

Change in Osmotic Pressure Influences the Absorption Spectrum of Hemoglobin inside Red Blood Cells.

Absorption spectra of red blood cell (RBC) suspensions are investigated in an osmolarity range in the medium from 200 mOsm to 900 mOsm. Three spectral parameters are used to characterize the process of swelling or shrinkage of RBC-the absorbance at 700 nm, the Soret peak height relative to the spectrum background, and the Soret peak wavelength. We show that with an increase in the osmolarity, the absorbance at 700 nm increases and the Soret peak relative height decreases. These changes are related to the changes in the RBC volume and the resulting increase in the hemoglobin intracellular concentration and index of refraction. Confocal microscopy and flow cytometry measurements supported these conclusions. The maximum wavelength of the Soret peak increases with increasing osmolarity due to changes in the oxygenation state of hemoglobin. Using these spectrum parameters, the process of osmosis in RBCs can be followed in real time, but it can also be applied to various processes, leading to changes in the volume and shape of RBCs. Therefore, we conclude that UV-Vis absorption spectrophotometry offers a convenient, easily accessible, and cost-effective method to monitor changes in RBC, which can find applications in the field of drug discovery and diagnostics of RBC and hemoglobin disorders.

A comparative evaluation of the variations on the shades of pressable ceramic system with the layering technique after different number of firing cycles: An in vitro study.

AIM: The main aim of the present study was to compare and evaluate the effect of repetitive firings on different shades of a pressable all ceramic system layered with veneering porcelain. SETTING AND DESIGN: In-vitro comparative study. MATERIALS AND METHODS: An in vitro comparative study was conducted, and a total of 60 disc shaped specimens (15 mm in diameter and 0.8 mm in thickness) were made of heat pressed ceramic of shades A2, A3, and B2 (20 discs of each shade) grouped as Group I, II, and III, respectively, using the lost wax technique. The discs were subsequently layered with veneering porcelain followed by glazing and overglazing and underwent a firing cycle at each step until six times combined. CIE L*a*b* measurements were noted on each sample after the third, fourth, fifth, and sixth firing using VITA Easyshade Advance 4.0 spectrophotometer. STATISTICAL ANALYSIS USED: Statistical Analysis was done by SPSS 17.0 software. One way analysis of variance, multiple comparisons using the Tukey test, and descriptive statistical analysis were done for all the groups in the study. P <0.05 was statistically significant. RESULTS: The mean color differences for the repeated firings were imperceptible (ΔE <1.67) to the human eye for all ceramic samples tested except between the fourth and fifth firing of Group II (shade A3). CONCLUSION: The analysis revealed that although repeated firings lead to changes in L*, a*, and b* values, the mean color difference was below the clinically acceptable color change (ΔE <3.7).

Comparative Analysis of Catalase Activity in Plants: Spectrophotometry and Native PAGE Approaches.

Catalase, a pivotal enzyme in plant antioxidative defense mechanisms, plays a crucial role in detoxifying hydrogen peroxide, a reactive oxygen species (ROS). In this chapter, a comparative analysis of catalase activity was conducted using two distinct methodologies: spectrophotometry and non-denaturing polyacrylamide gel electrophoresis (PAGE). The spectrophotometric approach allowed the quantification of catalase activity by measuring the breakdown rate of hydrogen peroxide, while native PAGE enabled the separation and visualization of catalase isozymes, based on their native molecular weight and charge characteristics, and specific staining assay. Both methods provide valuable insights into catalase activity, offering complementary information on the enzyme's functional diversity and distribution within different plant tissues. This study integrates different techniques, previously described, to comprehensively elucidate the role of catalase in plant metabolism. Furthermore, it provides the possibility of obtaining a holistic understanding of antioxidant defense mechanisms by considering both total activity and isoenzyme distribution of catalase enzyme.

Development of Improved Spectrophotometric Assays for Biocatalytic Silyl Ether Hydrolysis.

Reported herein is the development of assays for the spectrophotometric quantification of biocatalytic silicon-oxygen bond hydrolysis. Central to these assays are a series of chromogenic substrates that release highly absorbing phenoxy anions upon cleavage of the sessile bond. These substrates were tested with silicatein, an enzyme from a marine sponge that is known to catalyse the hydrolysis and condensation of silyl ethers. It was found that, of the substrates tested, tert-butyldimethyl(2-methyl-4-nitrophenoxy)silane provided the best assay performance, as evidenced by the highest ratio of enzyme catalysed reaction rate compared with the background (uncatalysed) reaction. These substrates were also found to be suitable for detailed enzyme kinetics measurements, as demonstrated by their use to determine the Michaelis-Menten kinetic parameters for silicatein.

Effects of Coloring Liquid Dipping Time and Surface Finishing Procedures on the Optical Properties of Monolithic Zirconia.

BACKGROUND: Monolithic zirconia restorations can be produced from self-colored or uncolored blocks. The coloring procedure of uncolored blocks and surface treatments may affect the appearance of the restoration. AIM: The purpose of this study is to evaluate the effect of liquid coloring and surface treatments on optical properties of translucent monolithic zirconia. METHODS: All specimens were cut from zirconia blocks with a thickness of 1 mm. Specimens were dipped in the coloring liquids for 3 min, 5 min, and 7 min and then divided into groups of 10 specimens for surface treatments. Glaze and mechanical polishing were applied, and the color of the specimens was measured under the D65 lighting condition with a spectrophotometer device. Color values obtained from the CIE Lab formula and the translucency parameter (TP), opalescence parameter (OP), and contrast ratio (CR) were calculated. The normality of the data was confirmed with the Shapiro-Wilk test. A three-way analysis of variance (ANOVA) was used to assess the effect of dipping time, liquid shade, and surface treatments. RESULTS: The effect of liquid shade and dipping time on the TP, OP, and CR parameters were statistically significant, and the TP values were reduced with the application of coloring liquid. Mechanical polishing groups had higher OP values and lower TP values than glazed groups. CONCLUSION: In cases where high translucency is required, it may be advisable to use self-colored blocks and apply glaze as a surface treatment to achieve the desired optical properties.

Field evaluation of a novel semi-quantitative point-of-care diagnostic for G6PD deficiency in Indonesia.

BACKGROUND: The WHO recommends routine testing of G6PD activity to guide radical cure in patients with Plasmodium vivax malaria. Females may have intermediate G6PD enzyme activity and to date, only complex diagnostics are able to reliably identify them. The semi-quantitative G6PD diagnostic "One Step G6PD Test" (Humasis, RoK; "RDT") is a lateral flow assay that can distinguish deficient, intermediate, and normal G6PD status and offers a simpler diagnostic alternative. METHODS: G6PD status of participants enrolled in Malinau and Nunukan Regencies and the capital Jakarta was assessed with the RDT, and G6PD activity was measured in duplicate by reference spectrophotometry. The adjusted male median (AMM) of the spectrophotometry measurements was defined as 100% activity; 70% and 30% of the AMM were defined as thresholds for intermediate and deficient G6PD status, respectively. Results were compared to those derived from spectrophotometry at the clinically relevant G6PD activity thresholds of 30% and 70%. RESULTS: Of the 161 participants enrolled, 10 (6.2%) were G6PD deficient and 12 (7.5%) had intermediate G6PD activity by spectrophotometry. At the 30% threshold, the sensitivity of the RDT was 10.0% (95%CI: 0.3-44.5%) with a specificity of 99.3% (95%CI: 96.4-100.0%); the positive predictive value was 50.0% (95%CI: 1.3-98.7%) and the negative predictive value 94.3% (95%CI: 89.5-97.4%). The corresponding figures at the 70% threshold were 22.7% (95%CI: 7.8-45.4%), 100.0% (95%CI: 97.4-100.0%), 100.0% (95%CI: 47.8-100.0%) and 89.1% (95%CI: 83.1-93.5%), respectively. CONCLUSION: While there is a dire need for an easy-to-use, economical, semi-quantitative diagnostic for the point of care, the observed performance of the "One Step G6PD Test" in its current form was insufficient to guide antimalarial treatment.

Effect of coffee thermocycling on the color and translucency of milled and 3D printed definitive restoration materials.

STATEMENT OF PROBLEM: Research on the color and translucency properties of 3-dimensionally (3D) printed definitive resins and the effect of coffee thermocycling on these properties is lacking. PURPOSE: The purpose of this in vitro study was to investigate the effect of coffee thermocycling on the color and translucency parameters of the milled and 3D printed materials used for definitive restorations. MATERIAL AND METHODS: Plate-shaped specimens (12×12×1 mm) of 3 milled (IPS e.max CAD (LDS), Vita Enamic (PICN), Cerasmart (RNC)) and two 3D printed (VarseoSmile Crownplus (VSP), Permanent Crown (PC)) were fabricated (n=12). The brightness (L*), red-green (a*), and yellow-blue (b*) parameters were measured with a spectrophotometer before and after 10 000 coffee thermocycles. The relative translucency parameters (RTP00) and color change were calculated using the CIEDE2000 formula. Stainability (ΔE00) and translucency differences (ΔRTP00) were evaluated. Data were analyzed with the Kruskal-Wallis, Mann-Whitney U, and Wilcoxon tests. The Spearman correlation test was used to analyze the ΔE00 and ΔRTP00 values (α=.05). RESULTS: The type of material and coffee thermocycling significantly affected the evaluated parameters at both measurement periods (P=.001). Coffee thermocycling decreased the L* and RTP00 values while increasing the a* and b* values (P=.001). The highest ΔE00 values were found in VSP and PC, which were statistically similar (P=.291), while the highest | ΔRTP00 | values were observed for VSP (P=.001). The lowest ΔE00 and | ΔRTP00 | values were found in LDS (P=.001). A positive relationship was found between the ΔE00 and | ΔRTP00| values (R=.590, P=.01). CONCLUSIONS: After coffee thermocycling, all tested materials exhibited a darkened, yellowish, and opaque appearance, although the alterations in color and translucency remained within clinically acceptable thresholds (AT00=1.81) for these materials.

Color matching and color recovery in large composite restorations using single-shade or universal composites.

This study assessed the color-matching ability and color recovery of unprepared teeth when using single-shade composites and a universal composite in large restorations. Buccal and palatine surface colors of molars were measured with a spectrophotometer (CIELAB) before preparing round cavities (6 mm in diameter, 2 mm in depth). The cavities were randomly filled with a single-shade composite (Omnichroma, Diamond One, or Vittra APS Unique) or a universal composite (Filtek Universal). Color measurements of the restored cavities were taken, and overall color differences (ΔEab and ΔE00) and differences in the whitening index for dentistry (ΔWID) from baseline were calculated. Additionally, visual assessments of a color match to the surrounding enamel were performed by forty evaluators (laypersons and undergraduate students of dentistry) in a viewing booth under illuminant D65, with rating scores from 0 (no color mismatch) to 4 (not acceptable). Data were analyzed using RM or one-way ANOVA (α = 0.05). Results showed that the restorations generally exhibited whiter colors (WID ranged from 27.9 to 41.3) than the unprepared teeth (WID ranged from 15.9 to 19.3). The composite Filtek Universal demonstrated the lowest color discrepancy (ΔWID = 8.6; ΔE00 = 10.8; and ΔE00 = 6.2), and no significant differences were observed among the evaluated single-shade composites. Furthermore, all composites showed similar and adequate color matches to the surrounding enamel. However, it is important to note that despite their ability to match the surrounding enamel reasonably, none of the composites evaluated in large restorations fully recovered the color observed in unprepared teeth.

Method development and validation for the quantitative determination of total flavonoids through the complexation of iron (III) and its application in real sample.

BACKGROUND: The determination of flavonoids in real sample using UV-Vis spectrophotometer commonly uses quercetin and catechin with Al+3 complexing agent as reference materials for the calibration of the instrument. However, getting these standard materials is challenging due to its expense and unavailability in the chemical reserve of the country. Moreover, the Al+3 - quercetin complexation standard method demands high amount of quercetin in spite of its high cost. Hence, developing alternative method that can solve this problem is crucial for the determination of flavonoids in the real sample. RESULTS: An iron-based complexation method for the determination of flavonoids in the real sample was developed that reduces the amount of quercetin by 200 times (1 mg/mL to 0.005 mg/mL) during the calibration of UV-Vis spectroscopy as an alternative method. The reaction parameters (incubation time, pH, and concentration of quercetin) were optimized using software Design Expert 11 and confirmed by the practical experiments. The kinetics of reaction between iron and quercetin was found to be pseudo first order with rate constant of kobs at 340 and 510 nm. The analysis window for the flavonoid complex was achieved with the kinetic discrimination of the interferences at its optimized time of complexation 20 min and absorbance maxima of 510 nm. The developed method was validated by evaluating its precision, accuracy, recovery test (84-117%), detection limit and quantification limit following the standard protocols. The calibration of the instrument has been developed for the new method and the linear regression coefficient (R2) of 0.998 was obtained. SIGNIFICANCE: Applying the developed standard material (Fe3+ - quercetin complex) gives freedom for the analytical chemists to find the standard materials that is accessible and cheaper than the existing one (Al3+-quercetin complex). The developed method can also be easily applied for determination of flavonoid in the real samples without potential interferences coming from sample matrix.

Effect of whitening toothpastes with different hydrogen peroxide concentrations: Penetration into the pulp chamber and color change.

OBJECTIVES: This study evaluated the efficacy of simulated brushing with toothpastes containing different concentrations of hydrogen peroxide (HP) in pulp chamber penetration and color change. Also, physical-chemical properties (concentration, pH and viscosity) were evaluated. METHODS: Forty-nine premolars were divided into seven groups (n = 7): untreated (control); whitening gel (White Class 6 %, 6 %BG) with one 90  min application (6 %BG 90  min) and 14 applications of 90  min (6 %BG 14×90 min); toothpastes (Colgate Luminous White Glow 3 %, 3 %TP; Crest 3D White Brilliance 4 %, 4 %TP; Colgate Optic White Pro-Series 5 %, 5 %TP) and 6 %BG toothbrushing for 14 applications of 90 s. HP penetration into the pulp chamber was measured through UV-Vis spectrophotometry and color change with a spectrophotometer (ΔEab, ΔE00, and ΔWID). Initial concentration, pH, and viscosity were measured through Titration, Digital pH-meter, and Rheometer, respectively. Statistical analysis used one-way ANOVA and Tukey's test (α = 0.05). RESULTS: 6 %BG (14×90 min) and 4 %TP groups showed acidic pH and higher concentrations of HP in the pulp chamber compared to the other groups (p < 0.05). On the other side, 3 %TP and 5 %TP groups showed alkaline pH, higher viscosity between the toothpastes and lower HP penetration (p < 0.05). The 6 %BG AH (14×90 min) group exhibited the most significant color change (ΔEab, ΔE00, and ΔWID) (p < 0.05). CONCLUSIONS: Brushing with whitening toothpaste with an acidic pH leads to greater HP penetration into pulp chamber; but, even when a high concentrated HP whitening toothpaste was used, a lower whitening effect was observed when compared to a two-week at-home bleaching. CLINICAL SIGNIFICANCE: Whitening toothpastes containing up to 5 % HP produced lower whitening effect than two-week at-home bleaching. Additionally, HP was detected within the pulp chamber which can potentially impact in tooth sensitivity.

Influence of repositioning guides' color and usage on precision in tooth color measurement with a clinical spectrophotometer.

BACKGROUND: Repositioning guides are commonly employed in clinical studies to ensure consistent tooth color measurements. Yet, their influence on measured color remains uncertain. OBJECTIVE: This study evaluated the impact of repositioning guides' color and usage on tooth color measurement using a clinical spectrophotometer. METHODOLOGY: In total, 18 volunteers participated in this study, in which the color of their upper left central incisor and upper left canine was measured with or without repositioning guides (control). The guides were made from pink, blue, or translucent silicone, as well as an acetate-based bleaching tray. Tooth color was measured in triplicates using a clinical spectrophotometer based on the CIELAB system. The standard deviations of these readings were used to estimate reproducibility, and color differences (ΔE00) between the measurements with guides and the control were calculated. RESULTS: Repositioning guides had a minimal effect on L* values and no effect on b* values. The use of pink silicone increased a* values, whereas blue or translucent silicone reduced them. Irrespective of the evaluated tooth, the lowest ΔE00 values were observed for the translucent silicone and bleaching tray. The usage of guides only affected data variability for the L* color coordinate. CONCLUSION: Using repositioning guides can significantly impact the precision of tooth color measurement with a clinical spectrophotometer.

Development of a point-of-care colorimetric metabolomic sensor platform.

Metabolomics is the large-scale study of small molecule metabolites within a biological system. It has applications in measuring dietary intake, predicting heart disease risk, and diagnosing cancer. Metabolites are often measured using high-end analytical tools such as mass spectrometers or large spectrophotometers. However, due to their size, cost, and need for skilled operators, using such equipment at the bedside is not practical. To address this issue, we have developed a low-cost, portable, optical color sensor platform for metabolite detection. This platform includes LEDs, sensors, microcontrollers, a power source, and a Bluetooth chip enclosed within a 3D-printed light-tight case. We evaluated the color sensor's performance using both a range of dyed water samples as well as well-established colorimetric reactions for specific metabolite detection. The sensor accurately measured creatinine, L-carnitine, ascorbate, and succinate well within normal human urine levels with accuracy and sensitivity equal to or better than a standard laboratory spectrophotometer. Our color sensor offers a cost-effective, portable alternative for measuring metabolites via colorimetric assays, thereby enabling low-cost, point-of-care metabolite testing.

Spider chart, greenness and whiteness assessment of experimentally designed multivariate models for simultaneous determination of three drugs used as a combinatory antibiotic regimen in critical care units: Comparative study.

In this study, five earth-friendly spectrophotometric methods using multivariate techniques were developed to analyze levofloxacin, linezolid, and meropenem, which are utilized in critical care units as combination therapies. These techniques were used to determine the mentioned medications in laboratory-prepared mixtures, pharmaceutical products and spiked human plasma that had not been separated before handling. These methods were named classical least squares (CLS), principal component regression (PCR), partial least squares (PLS), genetic algorithm partial least squares (GA-PLS), and artificial neural network (ANN). The methods used a five-level, three-factor experimental design to make different concentrations of the antibiotics mentioned (based on how much of them are found in the plasma of critical care patients and their linearity ranges). The approaches used for levofloxacin, linezolid, and meropenem were in the ranges of 3-15, 8-20, and 5-25 µg/mL, respectively. Several analytical tools were used to test the proposed methods' performance. These included the root mean square error of prediction, the root mean square error of cross-validation, percentage recoveries, standard deviations, and correlation coefficients. The outcome was highly satisfactory. The study found that the root mean square errors of prediction for levofloxacin were 0.090, 0.079, 0.065, 0.027, and 0.001 for the CLS, PCR, PLS, GA-PLS, and ANN models, respectively. The corresponding values for linezolid were 0.127, 0.122, 0.108, 0.05, and 0.114, respectively. For meropenem, the values were 0.230, 0.222, 0.179, 0.097, and 0.099 for the same models, respectively. These results indicate that the developed models were highly accurate and precise. This study compared the efficiency of artificial neural networks and classical chemometric models in enhancing spectral data selectivity for quickly identifying three antimicrobials. The results from these five models were subjected to statistical analysis and compared with each other and with the previously published ones. Finally, the whiteness of the methods was assessed by the recently published white analytical chemistry (WAC) RGB 12, and the greenness of the proposed methods was assessed using AGREE, GAPI, NEMI, Raynie and Driver, and eco-scale, which showed that the suggested approaches had the least negative environmental impact. Furthermore, to demonstrate solvent sustainability, a greenness index using a spider chart methodology was employed.

Investigation on the Validity of in vitro Sun Protection Factor and Ultraviolet-A Protection Factor Evaluation Method for Sunscreen Samples.

Factors affecting the in vitro Sun Protection Factor (SPF) and Ultraviolet-A Protection Factor (UVA-PF) of sunscreens were analyzed for verifying the validity and reliability of the ISO24443 evaluation method. UV absorbance measurements by different spectrophotometers did not lead to the large difference in in vitro SPF/UVA-PF, although the UV absorbance determined by each spectrophotometer exhibited relatively large difference when it was larger than 2. On the other hand, relatively large difference was found in in vitro SPF/UVA-PF by utilizing European Cosmetic and Perfumery Association (Colipa) 1994 or UV-solar simulated radiation (UV-SSR) for the spectral irradiance. Appropriateness of employing the coefficient of adjustment for the determination of in vitro UVA-PF was also found to be reexamined.