Impact of ultrasound process on cassava starch nanoparticles and Pickering emulsions stability.

Using green techniques to convert native starches into nanoparticles is an interesting approach to producing stabilizers for Pickering emulsions, aiming at highly stable emulsions in clean label products. Nanoprecipitation was used to prepare the Pickering starch nanoparticles, while ultrasound technique has been used to modulate the size of these nanoparticles at the same time as the emulsion was developed. Thus, the main objective of this study was to evaluate the stabilizing effect of cassava starch nanoparticles (SNP) produced by the nanoprecipitation technique combined with ultrasound treatment carried out in the presence of water and oil (more hydrophobic physicochemical environment), different from previous studies that carry out the mechanical treatment only in the presence of water. The results showed that the increased ultrasound energy input could reduce particle size (117.58 to 55.75 nm) and polydispersity (0.958 to 0.547) in aqueous dispersions. Subsequently, Pickering emulsions stabilized by SNPs showed that increasing emulsification (ultrasonication) time led to smaller droplet sizes and monomodal size distribution. Despite flocculation, long-term ultrasonication (6 and 9 min) caused little variation in the droplet size after 7 days of storage. The cavitation effects favored the interaction between oil droplets through weak attraction forces and particle sharing, favoring the Pickering stabilization against droplet coalescence. Our results show the potential to use only physical modifications to obtain nanoparticles that can produce coalescence-stable emulsions that are environmentally friendly.

Recent progress and perspectives of typical renewable bio-based flocculants: characteristics and application in wastewater treatment.

The research on bio-based flocculants for waste resource utilization and environmental protection has garnered significant attention. Bio-based flocculants encompass plant-based, animal-based, and microbial variants that are prepared and modified through biological, chemical, and physical methods. These flocculants possess abundant functional groups, unique structures, and distinctive characteristics. This review comprehensively discussed the removal rates of conventional pollutants and emerging pollutants by bio-based flocculants, the interaction between these flocculants and pollutants, their impact on flocculation performance in wastewater treatment, as well as their application cost. Furthermore, it described the common challenges faced by bio-based flocculants in practical applications along with various improvement strategies to address them. With their safety profile, environmental friendliness, efficiency, renewability, and wide availability from diverse sources, bio-based flocculants hold great potential for widespread use in wastewater treatment.

Enhanced sludge dewatering using a novel synergistic iron/peroxymonosulfate-polyacrylamide method.

In the sludge dewatering process, a formidable challenge arises due to the robust interactions between extracellular polymeric substances (EPS) and bound water. This study introduces a novel, synergistic conditioning method that combines iron (Fe2+)/peroxymonosulfate (PMS) and polyacrylamide (PAM) to significantly enhance sludge dewatering efficiency. The application of the Fe2+/PMS-PAM conditioning method led to a substantial reduction in specific filtration resistance (SFR) by 82.75% and capillary suction time (CST) by 80.44%, marking a considerable improvement in dewatering performance. Comprehensive analyses revealed that pre-oxidation with Fe2+/PMS in the Fe2+/PMS-PAM process effectively degraded EPS, facilitating the release of bound water. Subsequently, PAM enhanced the flocculation of fine sludge particles resulting from the advanced oxidation processes (AOPs). Furthermore, analysis based on the Extended Derjaguin-Landau-Verwey-Overbeek (XDLVO) theory demonstrated shifts in interaction energies, highlighting the breakdown of energy barriers within the sludge and a transition in surface characteristics from hydrophilic (3.79 mJ m-2) to hydrophobic (-61.86 mJ m-2). This shift promoted the spontaneous aggregation of sludge particles. The innovative use of the Flory-Huggins theory provided insights into the sludge filtration mechanism from a chemical potential perspective, linking these changes to SFR. The introduction of Fe2+/PMS-PAM conditioning disrupted the uniformity of the EPS-formed gel layer, significantly reducing the chemical potential difference between the permeate and the water in the gel layer, leading to a lower SFR and enhanced dewatering performance. This thermodynamic approach significantly enhances our understanding of sludge dewatering and conditioning. These findings represent a paradigm shift, offering innovative strategies for sludge treatment and expanding our comprehension of dewatering and conditioning techniques.

A synthetic and transparent clay removes Microcystis aeruginosa efficiently.

Clay-algae flocculation is a promising method to remove harmful algal blooms (HABs) in aquatic ecosystems. Many HAB-generating species, such as Microcystis aeruginosa (M. aeruginosa), a common species in lakes, produce toxins and harm the environment, human health, and the economy. Natural clays, such as bentonite and kaolinite, and modification of these clays have been applied to mitigate HABs by forming large aggregates and settling down. In this study, we aim to examine the impact of laponite, a commercially available smectite clay that is synthetic, transparent, compatible with human tissues, and degradable, on removing HABs. We compare the cell removal efficiencies (RE) of laponite, two natural clays, and their polyaluminum chloride (PAC)-modified versions through clay-algae flocculation experiments. Our results show that the optimum concentrations of laponite, bentonite, kaolinite, PAC-modified bentonite, and PAC-modified kaolinite to remove 80 % of the M. aeruginosa cells from the water column are 0.05 g/L, 2 g/L, 4 g/L, 2 g/L and 0.3 g/L respectively. Therefore, to achieve the same cell removal efficiency, the amount of laponite needed is 40 to 80 times less than bentonite and kaolinite, and 6 times less than PAC-modified kaolinite. We demonstrate that the superior performance of laponite clay is because of its smaller particle size, which increases the encounter rate between cells and clay particles. Furthermore, experiments using water samples from Powderhorn Lake confirmed laponite's effectiveness in mitigating HABs. Our price analysis also suggests that this commercially-available clay, laponite, can be used in the field at a relatively low cost.

Co-flotation of effluents from detergent and marble processing industries in Denver and dispersed air flotation systems.

Suspended solids in the marble processing wastewater (MPWW) have the potential to pollute receiving media. Likewise, detergent production wastewater (DPWW) needs treatment prior to discharge as they include surfactants and others. Flotation and its modifications are common for separation purposes in various engineering solutions. To increase flotation performance by changing the surface tension some collector and frother chemicals, surfactants are utilized. Detergents are among important surfactants and they may act as both frother and collector in flotation. Therefore, the purpose of this study was to determine the effectiveness of DPWW in co-flotation with MPWW. Two effluents were mixed at varying ratios and dispersed air (DISP) and Denver (DEN) flotation co-treatment were applied to the mixtures. Volume ratio, time and air flow rate on treatment performance were investigated. Turbidity, solids, COD, phosphate removals were achieved at varying levels when the flotation was applied to the mixture. The highest treatment performance was achieved at 90%MPWW-10%DPWW mixture. 10 min flotation time and 2 L min-1 air flow rate for the DEN system, and 20 min and 6 L min-1 for the DISP system were recommended. Under these conditions turbidity, SS, COD, phosphate and alkalinity residuals (and removal efficiencies) were 2400 NTU(82%), 1720 mg.L-1(89%), 313.6 mg.L-1(10%), 20 mg.L-1(20%) and 600 mg.L-1CaCO3(92%) in the DEN system, respectively. Whereas, in the DISP system, under the same conditions, final values of 1880 NTU(86%), 1540 mg.L-1(91%), 262 mg.L-1(17%), 21 mg.L-1(20%) and 470 mg.L-1(94%) were obtained, respectively. The highest SludgeSS concentration increased up to 19300 mg.L-1 in the 90%-10% mixture. In all samples, dewaterable sludge was obtained. By this study, co-flotation of these two effluents was recommended. Within SDGs, this approach will replace frother chemical usage. The process performance can further be enhanced via flotation modifications and technology can be developed as further study.

Enhanced inhibitory efficiency against toxic bloom forming Raphidiopsis raciborskii by Streptomyces sp. HY through triple algicidal modes: Direct and indirect attacks combined with bioflocculation.

Raphidiopsis raciborskii (R. raciborskii) forms harmful cyanobacterial blooms globally, and poses a great threat to the safety of drinking water and public health. There is a great need to develop eco-friendly biological alternative measures to mitigate mass blooms of R. raciborskii. However, previous rare studies on algicidal microorganisms against R. raciborskii restricted this aim. Recently, an algicidal bacterium Streptomyces sp. HY (designated HY) was identified with flavones producing ability, and could remove up to 98.73 % of R. raciborskii biomass within 48 h by directly attacking the cyanobacterium and release of algicidal substances (i.e., flavonoids) with a inoculum ratio of 5 %. Algicidal rate of HY was enhanced by 88.05 %, 89.33 % under dark and light, and full-light conditions respectively, when compared with the dark condition. Its algicidal substances were stable in a broad range of temperature (-80-55 °C) and pH (3-11) conditions, and all treated groups exhibited ≈ 100 % algicidal rate at day 3. HY treatment disrupted the photosynthesis system and triggered serious oxidative stress resulting in severe morphological injury. Thereby, HY treatment significantly affected expression levels of several essential genes (i.e., psbA, psaB, rbcL, ftsZ, recA, grpE), and simultaneously inhibited the biosynthesis and release of cylindrospermopsin. Yet, HY treatment didn't show any toxicity to zebrafish test embryos. Such results indicate that HY is a promising algicidal candidate strain to control global R. raciborskii blooms, and holds great promises for an effective biological measure to sustain water safety.

Self-flocculating Chlorella vulgaris: A high-efficiency purification mechanism of radioactive Th4+ in an aquatic environment.

This study aimed to investigate the purification of radioactive thorium (Th4+) by Chlorella vulgaris in aquatic environments. Single-factor experiments and response surface optimization tests identified optimal purification conditions. The purification and metabolic response mechanisms of Chlorella to Th4+ were elucidated using physiological and biochemical analyses, three-dimensional excitation-emission matrix (3D-EEM) analysis, and metabolomic profiling. Increases in the Th4+ concentration caused Chlorella to self-flocculate, significantly improving the Th4+ purification efficiency. Under optimal conditions, the Th4+ purification efficiency for Th4+ in wastewater by Chlorella stabilized between 94.3 % and 98.2 %. Morphological analysis revealed that the purified Th4+ existed mainly in a stable residual state. Chlorella efficiently purified wastewater during treatment by regulating environmental pH, performing redox reactions, and utilizing extracellular polymeric substances (EPS) to interact with Th4+. Metabolomic analysis indicated that Chlorella adapted to the Th4+-contaminated environment and enhanced its purification function by adjusting the synthesis of metabolites, such as carbohydrates, nucleotides, and amino acids. Chlorella demonstrated a remarkable self-flocculation phenomenon and a high-efficiency purification capability for Th4+, offering new possibilities for environmental remediation. Its purification mechanism involves environmental regulation, redox reactions, and complex metabolic adjustments. The results presented here provide theoretical support for environmental remediation using Chlorella.

Enhanced consolidation and removal of accumulated flocculants in dredged soil via leaching with vacuum preloading.

The vacuum preloading coupling flocculation treatment is a widely employed method for reinforcing soils with high water content in practical construction. However, uneven distribution and accumulation of flocculants pose significant damage to the soil environment and result in uneven soil consolidation, leading to severe issues in subsequent soil development and exploitation. To address these concerns, an evolved leaching with vacuum method is developed for facilitating soil consolidation while preventing the accumulation of flocculant in the soil. In this study, five model tests are conducted in which FeCl3 is chosen as the typical flocculant to promote soil consolidation, and deionized water is used for leaching. The final discharged water, settlement, water content and penetration resistance of soil are obtained to evaluate the soil reinforcement effect, while the flocculant removal effect is evaluated by the Fe3+ content in the filtrate and soil. The comprehensive reinforcement and flocculant removal effect show that this method is extremely effective compared to traditional vacuum preloading. The two leaching is clarified as the best choice, resulting in a 22% decrease in the soil water content and a 25% in soil penetration resistance, meanwhile a 12.8% removal rate of the flocculant. The test results demonstrate that leaching with vacuum preloading can contribute to promoting soil consolidation and reducing the accumulation of flocculant in the soil, ensuring the safe and eco-friendly use of the soil for future applications. The conclusions obtained are of significant theoretical value and technical support for practical construction and sustainable development.

A systematic investigation of peracetic acid oxidation and polymeric coagulants re-flocculation to enhance activated sludge dewatering: Multi-porous skeleton structures.

In this research, the effects of peracetic acid (PAA), polymeric flocculants, and their combined conditioning on improving the dewatering performance were comprehensively evaluated. The results showed that sludge cake moisture content, capillary suction time (CST), and specific resistance to filtration (SRF) were 70.6%, 48.1 s, and 3.42 × 1012 m/kg after adding 0.10 g/gMLSS PAA for 50 min, representing reductions of 12.60%, 40.32%, and 33.98%, respectively. Additionally, conditioning of sludge with polyferric sulfate (PFS), polyaluminum chloride (PAC), and cationic polyacrylamide (CPAM) enhanced sludge properties in the following order: CPAM > PAC > PFS. After the PAA oxidation and re-flocculation process, the optimal dosages of PFS, PAC, and CPAM were reduced to 1.5 g/L, 0.9 g/L, and 0.04 g/L, respectively. The sludge dewatering performance significantly improved, with sludge cake moisture content measuring 65.8%, 66.3%, and 61.7%, respectively. Moreover, the spatial multi-porous skeleton structures were formed via re-flocculation to improve the sludge dewatering. Furthermore, economic evaluation validated that the pre-oxidation and re-flocculation process could be considered an economically viable option. These research findings could serve as a valuable reference for practical engineering applications.

Deciphering the Dual Roles of an Alginate-Based Biodegradable Flocculant in Anaerobic Fermentation of Waste Activated Sludge: Dewaterability and Degradability.

Biodegradable flocculants are rarely used in waste activated sludge (WAS) fermentation. This study introduces an alginate-based biodegradable flocculant (ABF) to enhance both the dewatering and degradation of WAS during its fermentation. Alginate was identified in structural extracellular polymeric substances (St-EPS) of WAS, with alginate-producing bacteria comprising ∼4.2% of the total bacterial population in WAS. Owing to its larger floc size, higher contact angle, and lower free energy resulting from the Lewis acid-base interaction, the addition of the prepared ABF with a network structure significantly improved the dewaterability of WAS and reduced capillary suction time (CST) by 72%. The utilization of ABF by an enriched alginate-degrading consortium (ADC) resulted in a 35.5% increase in the WAS methane yield owing to its higher hydrolytic activity on both ABF and St-EPS. Additionally, after a 30 day fermentation, CST decreased by 62% owing to the enhanced degradation of St-EPS (74.4%) and lower viscosity in the WAS + ABF + ADC group. The genus Bacteroides, comprising 12% of ADC, used alginate lyase (EC 4.2.2.3) and pectate lyase (EC 4.2.2.2 and EC 4.2.2.9) to degrade alginate and polygalacturonate in St-EPS, respectively. Therefore, this study introduces a new flocculant and elucidates its dual roles in enhancing both the dewaterability and degradability of WAS. These advancements improve WAS fermentation, resulting in higher methane production and lower CSTs.

Exploring the influence of aquatic phosphate on Fe floc dynamics in water treatment.

The formation of flocs is crucial in the coagulation process of water treatment. However, the nature of ligand exchange on the surface of primary nanoparticles (PNPs) during floc formation requires further investigation to enhance our understanding of the coagulation mechanism. Phosphate (P) is a ubiquitous nutrient ion in aquatic surface water, in this study, the impact of P on floc growth under different pH conditions were investigated. The results revealed that floc growth patterns depended on both P dosage and pH. The mode of ligand exchange between P and in-situ formed ferric hydroxide within a pH range of 5 to 10 was further explored, and remarkable disparities in pH changes induced by P addition were observed. At lower pH levels, OH- release occurred relatively slowly, stabilizing with continued P addition. At neutral pH, OH- release was comparatively higher with P addition, while under alkaline conditions, both the quantity of OH- and its release rate decreased. It was deduced that Fe-OH21/2+ sites function as "active sites," while Fe-OH1/2- sites act as "inert sites" on the surface of PNPs formed during flocculation. These sites are crucial in the interconnections between flocs formed during coagulation and in floc growth. Analyses of Fe PNPs by Scanning Electron Microscopy (SEM) and Transmission Electron Microscopy (TEM), with and without P addition, revealed that the introduction of P inhibits or interferes with the self-crystallization of Fe PNPs through chemical coordination reactions. The results offer deeper insights into the coagulation mechanism and the transformation of Fe flocs in raw waters containing P during water treatment practices.

New insights into membrane fouling in coagulation-ultrafiltration by cake characteristics analysis: A case study with PACl-Al13 and PACl.

Membrane fouling is a bottleneck issue that hindered the further application of ultrafiltration technology. To alleviate membrane fouling, coagulation-ultrafiltration (C-UF) process using polyaluminum chloride (PACl) and PACl-Al13 with high proportion of Al13O4(OH)247+ as coagulants, respectively, were investigated at various pH conditions. Results indicated that an increase in solution pH contributed to larger floc size and looser floc structure for both PACl and PACl-Al13. It was conducive to the formation of more porous cake, as evidenced by mean pore area and pore area distribution of cake, leading to lower reversible fouling. Furthermore, humic acid (HA) removal presented a trend of first increasing and then decreasing with the increase of pH. The optimal HA removal was achieved at pH 6 regardless of coagulant type, suggesting that the slightest irreversible fouling should be occurred at this point. Interestingly, the irreversible fouling with PACl coagulant achieved a minimum value at pH 9, while the minimal irreversible fouling with PACl-Al13 was observed at pH 6. We speculated that the cake formed by PACl could further intercept HA prior to UF process at alkaline pH. Furthermore, compared with PACl, PACl-Al13 had a stronger charge neutralization ability, thus contributing to more compact floc structure and higher HA removal at various pH conditions. By UF fractionation measurement, higher HA removal for PACl-Al13 was due to higher removal of HA with molecular weight less than 50 kDa.

Pickering emulsion stabilization with colloidal lignin is enhanced by salt-induced networking in the aqueous phase.

We study the effect of electrolytes on the stability in aqueous media of spherical lignin particles (LP) and its relevance to Pickering emulsion stabilization. Factors considered included the role of ionic strength on morphology development, LP size distribution, surface charge, interfacial adsorption, colloidal and wetting behaviors. Stable emulsions are formed at salt concentrations as low as 50 mM, with the highest stability observed at a critical concentration (400 mM). We show salt-induced destabilization of LP aqueous dispersions at an ionic strength >400 mM. At this critical concentration LP flocculation takes place and particulate networks are formed. This has a profound consequence on the stability of LP-stabilized Pickering emulsions, affecting rheology and long-term stability. The results along with quartz microgravimetry and confocal microscopy observations suggest a possible mechanism for stabilization that considers the interfacial adsorption of LP at oil/water interfaces. The often-unwanted colloidal LP destabilization in water ensues remarkably stable Pickering emulsions by the effect of network formation.

Deep learning-based flocculation sensor for automatic control of flocculant dose in sludge dewatering processes during wastewater treatment.

In sludge dewatering of most wastewater treatment plants (WWTPs), the dose of polymer flocculant is manually adjusted through direct visual inspection of the flocs without the aid of any instruments. Although there is a demand for the development of automatic control of flocculant dosing, this has been challenging owing to the lack of a reliable flocculation sensor. To address this issue, this study developed a novel image sensor for measuring the degree of flocculation (DF) based on deep learning. Two types of sludge samples were used in the laboratory-scale flocculation tests: excess sludge and mixtures of excess sludge and raw wastewater. To search for a deep learning regression model suitable for DF inference, ten models, including convolutional neural networks, vision transformers, and a multilayer perceptron MLP mixer, were comparatively analysed. The ConvNeXt and MLP mixer models showed the highest accuracies with coefficients of determination (R2) greater than 0.9. The region contributing to the DF inference in the flocculation images was visualised using a modulus-weighted, gradient-weighted regression activation map. A prototype of the flocculation sensor was constructed using an inexpensive EdgeAI device. This device comprises a single-board computer and an integrated graphical processing unit (GPU) and is equipped with a quantised ConvNeXt model. The maximum inference speed of the sensor was 12.8 frames per second (FPS). The flocculation control tests showed that the sensor could control the DF to the target value by adjusting the polymer flocculant dose. Therefore, the flocculation sensor can provide a data-driven approach to the management of the flocculation process, thereby facilitating the automation of WWTPs.

Multi-interface interaction mechanism of pulp reject-based flocculants for the removal of antibiotics and its combined pollutants.

The efficient removal of antibiotics and its combined pollutants is essential for aquatic environment and human health. In this study, a lignin-based organic flocculant named PRL-VAc-DMC was synthesized using pulp reject as the raw material, with vinyl acetate (VAc) and methacryloxyethyltrimethyl ammonium chloride (DMC) as the grafting monomers. A series of modern characterization methods were used to confirm the successful preparation of PRL-VAc-DMC and elucidate its polymerization mechanism. It was found that the Ph-OH group and its contiguous carbon atoms of lignin served as the primary active sites to react with grafting monomers. Flocculation experiments revealed that PRL-VAc-DMC could react with tetracycline (TC) through π-π* interaction, hydrophobic interaction, hydrogen bonding, and electrostatic attraction. With the coexistence of humic acid (HA) and Kaolin, the aromatic ring, hydroxyl, and amide group of TC could react with the benzene ring, hydroxyl group, and carboxyl group of HA, forming TC@HA@Kaolin complexes with Kaolin particles acting as the hydrophilic shell. The increase in particle size, electronegativity, and hydrophily of TC@HA@Kaolin complexes facilitated their interaction with PRL-VAc-DMC through strong interfacial interactions. Consequently, the presence of HA and Kaolin promoted the removal of TC. The synergistic removal mechanism of TC, HA, and Kaolin by PRL-VAc-DMC was systematically analyzed from the perspective of muti-interface interactions. This paper is of great significance for the comprehensive utilization of pulp reject and provides new insights into the flocculation mechanism at the molecular scale.

Characteristics and stabilization of Pickering emulsions constructed using myosin from bighead carp (Aristichthys nobilis).

Myosin from bighead carp (Aristichthys nobilis) as a main type of fish protein possesses a good emulsifying ability. However, whether bighead carp myosin (BCM) could construct stable Pickering emulsions is still unclear. Therefore, myosin particles and Pickering emulsions stabilized by bighead carp myosin (BCMPEs) were analyzed. The surface structure of BCM particles at 0.6 mol/L NaCl treatment was uniform and compact with a contact angle of 86.4 ± 2.7°, exhibiting the potential ability to construct O/W Pickering emulsions. The size and flocculation index (FI) of BCMPEs decreased with the increase in BCM concentrations of 1%-4% (w/v). Reversely, the size of BCMPEs increased with the increase in oil-water ratios. BCM particles could uniformly distribute at the oil-water interface to stabilize BCMPEs at a BCM concentration of 4% (w/v) and an oil-water ratio of 6:4 (v/v). This study could help explore fish proteins to construct Pickering emulsions for the deep processing of fish products.

Investigating flocculation mechanisms and ecological safety of cationic guar gum for rapid harvesting of microalgal cells.

Addressing the drawbacks of traditional flocculants on microalgae biomass harvesting is crucial for large-scale industrial applications of microalgae production. In this study, cationic bioflocculant was successfully prepared by introducing cationic groups into the side chain of guar gum, achieving in-situ algae flocculation efficiency of 83.5 % with the dosage of 18.0 mg/L under pH = 10.0. Through a harmonious integration of predictive modelling and practical experimentation, a superior cell flocculation capacity of 23.5 g/g was achieved. In addition, the environmental safety and biocompatibility of cationic guar gum was assessed, using the typical suspension quantitative bacteriostatic method and the fluorescent double-staining technique. The results showed that the inhibition efficiency of Staphylococcus aureus in the system containing 60.0 mg/L cationic guar gum was only 12.0 % and there was no inhibition against Escherichia coli colonies. These findings provide a safe and green flocculant for efficient microalgae harvesting and spent medium treatment.

Harvesting of cyanobacteria and phosphorus by electrocoagulation-flocculation-flotation: Role of phosphorus precipitation in cell separations and organics destabilization.

A high level of phosphate triggers the excretion of algogenic organic matter (AOM) during algae blooming, leading to disinfection by-products (DBPs) formation. The presence of phosphate could impact cyanobacteria harvesting and AOM separations by electrocoagulation. This study aims to investigate the role of phosphate in cell separations and AOM destabilization by Al-based electrocoagulation-flocculation-flotation (EFF) for harvesting of cyanobacteria and phosphate. The Al-based EFF was conducted to harvest Microcystis aeruginosa (MA) with varied phosphate (0-10 mg/L) at 5 mA/cm2 and pH 8. Fluorescent organic fractions, molecular weight distributions, the properties of flocs and DBPs formation potential were fully investigated. The results showed that the EFF at a low level of phosphate (1 mg/L) effectively improves the harvesting of MA cells, phosphate and the reduction in dissolved organic matter (DOC) up to 99.5 %, 95 % and 50 %, respectively. However, the presence of concentrated phosphate (10 mg/L) alleviates cell harvesting and worsens AOM separations due to ineffective floc formation induced by the fast formation of inactive AlPO4 precipitates along with limited Al(OH)3. At such a condition, it worsens DBPs precursors minimization owing to AOM release from MA cells. The increase in the current density during EFF can compensate for cell harvesting efficiency even though at concentrated phosphate, but it further induces AOM release. It is concluded that Al-based EFF demonstrates an efficient harvesting of cyanobacteria, phosphorus and AOM separations from algae-laden water under phosphate impact.

Efficient, quick, and low-carbon removal mechanism of microplastics based on integrated gel coagulation-spontaneous flotation process.

To address the problems of unstable efficiency, long treatment period, and high energy consumption during microplastics (MPs) removal by traditional coagulation-flotation technology, a gel coagulation-spontaneous flotation (GCSF) process is proposed that employs laminarin (LA) as the crosslinker and polyaluminum chloride (PAC)/polyaluminum ferric chloride (PAFC) as the coagulant to remove MPs. Herein, the effects of GCSF chemical conditions on microplastic-humic acid composite pollutants (MP-HAs) removal were investigated, and the removal mechanisms were analyzed through theoretical calculations and floc structure characterization. Results showed that an LA to PAC/PAFC ratio of 2.5:1 achieved the highest removal of HA (86 %) and MPs (93 %-99 %) in short coagulation (< 1 min) and spontaneous flotation (< 9 min) period. PAC-LA exhibited strong removal ability for MP-HAs while PAFC-LA induced fast flotation speed. The peak intensity and peak shift in Fourier-transformed infrared and X-ray photo-electron spectra indicated that the removal mechanisms of MPs include hydrogen bond adsorption and the sweeping effect, mainly relying on -OH/-C = O on the MPs surface and entrapment of gel flocs with a high degree of aggregation, respectively. The extended Derjaguin-Landau-Verwey-Overbeek calculation also revealed that interactions between PAC/PAFC-LA and MP-HAs were mainly polar interaction (hydrogen bonding) and intermolecular attraction interaction (Lifshitz-van der Waals force), and the sweep effect was reflected by intermolecular interaction. In addition, density function theory calculations indicated that -OH in LA mainly adsorbs DO through a double hydrogen bond configuration, and the crosslinking ligand FeO6/AlO6 assists in DO absorption by -OH.

Effects of residual foaming agent and defoamer on defoaming-flocculation-filterpress characteristics of earth pressure balance shield muck.

Foaming agents as a combination of several components are usually used as soil conditioning during earth pressure balance shield (EPBS) tunnelling. These residues in waste EPBS muck lead to a series of new challenges for in-situ recycling, i.e., foams overflow flocculation tank. This study investigates the effects of residual foaming agent components and defoamers on defoaming-flocculation-filterpress characteristics of EPBS muck using an improved flocculation and filterpress system. Residual foam height (Hf), defoaming ratio (DFR), antifoaming ratio (AFR), total suspended substance (TSS), turbidity, moisture content (MC), and zeta potential (ZP) were selected as characterization indices. The microstructure of filterpress cakes was analyzed using a scanning electron microscope. Results demonstrate that an enhancement within 0.0-1.0wt.% for sodium fatty alcohol polyoxyethylene ether sulfate (AES) and alpha olefin sulfonate (AOS) significantly reduces DFR and AFR. The MC and ZP decline, while the Hf and turbidity enhance. The combinations of nonionic surfactants alkyl polyglycoside (APG) and fatty alcohol-polyoxyethylene ether (AEO) in a concentration range of 0.0-1.0wt.% with 0.2wt.% AES causes the Hf, DFR, AFR, turbidity, and ZP to exhibit absolutely different variations. The MC with the growth in both APG and AEO presents a trend of first decreasing and then increasing. By increasing foam stabilizers sodium carboxymethyl cellulose (CMC) and guar gum (GG) within 0.02-0.10wt.%, the AFR, TSS, and ZP enhance in varying degrees, while the Hf, DFR, and MC gradually reduce. With the increase of defoamers hydroxyl silicone oil-glycerol polyoxypropylene ether (H-G) and dimethyl silicone oil-glycerol polyoxypropylene ether (D-G) within 0.002-0.010wt.%, the DFR and AFR are significantly improved, while the TSS, turbidity, MC, and ZP display varying degrees of reduction. Moreover, defoaming-flocculation-filterpress mechanisms of EPBS muck are explored to provide a useful reference for actual in-situ recycling projects.