On Corporate Accountability: Lead, Asbestos, and Fossil Fuel Lawsuits.

This paper examines the use of lawsuits against three industries that were eventually found to be selling products damaging to human heath and the environment: lead paint, asbestos, and fossil fuels. These industries are similar in that some companies tried to hide or distort information showing their products were harmful. Common law claims were eventually filed to hold the corporations accountable and compensate the injured. This paper considers the important role the lawsuits played in helping establish some accountability for the industries while also noting the limitations of the lawsuits. It will be argued that the lawsuits helped create pressure for government regulation of the industries' products but were less successful at securing compensation for the injured. Thus, the common law claims strengthened and supported administrative regulation and the adoption of industry alternatives more than they provided a means of legal redress.

Polychlorinated biphenyl contamination of paints containing polycyclic- and Naphthol AS-type pigments.

This study reports the concentrations and congener partners of polychlorinated biphenyls (PCBs) in commercially available paints. Polycyclic-type pigments containing dioxazine violet (pigment violet (PV) 23, PV37) and diketopyrrolopyrrole (PR254, PR255) were found to contain PCB-56, PCB-77, PCB-40, PCB-5, and PCB-12, and PCB-6, PCB-13, and PCB-15, respectively, as major congeners. Dioxazine violet is contaminated with by-products during synthesis from o-dichlorobenzene, which is used as a solvent during synthesis, and diketopyrrolopyrrole is contaminated with by-products during synthesis from p-chlorobenzonitrile. The concentration of PCBs in paint containing PV23 or PV37 was 0.050-29 mg/kg, and toxic equivalency (TEQ) values ranged 1.1-160 pg-TEQ/g. The concentration of PCBs in paint containing PR254 or PR255 was 0.0019-2.4 mg/kg. Naphthol AS is an azo-type pigment, and PCB-52 was detected in paint containing pigment red (PR) 9 with 2,5-dichloroaniline as its source. PCB-146, PCB-149, and PCB-153 were identified from paint containing PR112 produced from 2,4,5-trichloroaniline, as major congeners. These congeners have chlorine positions similar to aniline, indicating that these congeners are by-products obtained during the synthesis of pigments. The concentrations of PCBs in paints containing PR9 and PR112 were 0.0042-0.43 and 0.0044-3.8 mg/kg, respectively. The corresponding TEQ for PR112 was 0.0039-8.6 pg-TEQ/g.

The impact of culture medium on the development and physiology of biofilms of Pseudomonas fluorescens formed on polyurethane paint.

Microbial biofilms cause the deterioration of polymeric coatings such as polyurethanes (PUs). In many cases, microbes have been shown to use the PU as a nutrient source. The interaction between biofilms and nutritive substrata is complex, since both the medium and the substratum can provide nutrients that affect biofilm formation and biodeterioration. Historically, studies of PU biodeterioration have monitored the planktonic cells in the medium surrounding the material, not the biofilm. This study monitored planktonic and biofilm cell counts, and biofilm morphology, in long-term growth experiments conducted with Pseudomonas fluorescens under different nutrient conditions. Nutrients affected planktonic and biofilm cell numbers differently, and neither was representative of the system as a whole. Microscopic examination of the biofilm revealed the presence of intracellular storage granules in biofilms grown in M9 but not yeast extract salts medium. These granules are indicative of nutrient limitation and/or entry into stationary phase, which may impact the biodegradative capability of the biofilm.

Is nanotechnology revolutionizing the paint and lacquer industry? A critical opinion.

Many paints for indoor and outdoor applications contain biocides and additives for protection against microbial, physical and chemical deterioration. The biocides should remain active as long as they are incorporated in the paint. Protection against microbial colonization should last at least a decade. Once the biocides are released they should degrade within a short time so that no accumulation in the environment can occur. The paint industry is not only focusing their research in producing better paint formulations with degradable biocides: they also consider using nanomaterials, such as nanosilver, nanocopper, nanozinc oxide, photocatalytic-active nanotitanium dioxide and nanosilica dioxide as additives for the protection of paints, against microbial degradation and physical and chemical deterioration. In the future nanomaterials should replace biodegradable biocides and improve the paint properties as well as impede colonization by microorganisms. At the time there is no guarantee that the nanomaterials in paints and façades will fulfill their task in the long run, since there are no long term studies available. From nanosilver doped paints it is known that silver is easily washed out by rain. Photocatalytic active nanotitanium dioxide adsorbs ultra violet light (UV-light) and generates hydroxyl radicals, which not only inhibit microbial growth but can also initiate or accelerate the photocatalytic degradation of the paint matrix. Thus at this time it is still unknown if it makes sense to incorporate nanomaterials into paints. Intensive research and development are still needed in order to find the answers.

Elevated blood lead levels and cytogenetic markers in buccal epithelial cells of painters in India: genotoxicity in painters exposed to lead containing paints.

BACKGROUND, AIM, AND SCOPE: Lead, a major contaminant, is highly used in paint manufacturing due to its anticorrosive properties. Recent reports indicated high lead content among Indian paints used for commercial purposes. Painters are continuously exposed to these lead containing paints during painting of both commercial as well as residential buildings. Lead is well-known for its genotoxicty in occupational workers; however, in Indian painters the genotoxic effects of lead have not been reported to date. Therefore we aimed to study the genotoxic end points in painters due to their long-term exposure to these high lead-containing Indian paints. MATERIALS AND METHODS: Study group selection was made after a questionnaire administration, which included questions about lifestyle and medical history to exclude exposure to the other potential sources of genotoxics. Blood and buccal cell samples were obtained from 30 male painters and from a similar number of age-matched controls of same location with no occupational exposure to lead. Blood lead levels (Pb-B) were measured in painters and controls. Micronucleus (MN) frequencies and nuclear changes, i.e., karyorrhexis, karyolysis, broken egg, and binucleated, were investigated in buccal epithelial cells. RESULTS: Painters had significantly (P < 0.01) greater lead levels in blood than the control group. MN frequencies and nuclear changes in buccal epithelial cells were also significantly (P < 0.01) elevated in painters as compared with control subjects. Regression analysis also revealed significant (P < 0.01) association of Pb-B with all the genotoxic endpoints in painters. Cytogenetic damage was significantly associated with Pb-B as no other co-founding factors (smoking, alcohols) showed significant difference between both groups. DISCUSSION: Lead is widely used in paints which may serve as potential source of exposure among painters due to their long-term engagement with paints. Our results clearly demonstrated genotoxicity among the exposed population as evident from increase micronucleus frequencies, frequent nuclear changes, and apoptosis. Many studies had previously related nuclear change events in buccal epithelial cells with the progression of different carcinomas. Furthermore in-depth investigations with larger sample size are needed to provide evidence to this effect. CONCLUSIONS: Here, we report cytogenetic toxicity to the exposed population by the high lead containing paints from India for the first time. Frequent, high and unregulated use of lead in paints may cause genetic mutation and may accelerate cytogenetic damage which may further lead to different carcinomas in painters. These findings need to be considered and necessary steps should be taken to protect the occupational workers engaged with these high lead-containing paints. RECOMMENDATIONS: The use of lead in paints is completely unregulated in India and routine surveillance of paints for lead content is still lacking. These paints are readily available in markets and are also used in other products (jewelry, miniblinds) which could be exported to other countries including United States and Europe. Serious consideration should be given to the inclusion of regulations and bans on the use of lead in paints. Moreover, attention should also be paid towards the use of various protective measures (face-masks, hand gloves, and separate clothes) by the workers as safe work practices during working periods.

Potential damage to modern building materials from 21st century air pollution.

The evolution of damage to building materials has been estimated for the 21st century, with a particular focus on aluminum, zinc, copper, plastic, paint, and rubber in urban areas. We set idealized air pollution and climates to represent London and Prague across the period 1950-2100. Environmental parameters were used to estimate future recession, corrosion, and loss of properties through published damage or dose-response functions. The 21st century seems to provide a less aggressive environment for stone and metals than recent times. Improvements in air quality are the most relevant drivers for this amelioration. Changes in climate predicted for the 21st century do not alter this picture. On the other hand, polymeric materials, plastic, paint, and rubber might show slightly increased rates of degradation, to some extent the result of enhanced oxidant concentrations, but also the possibility of contributions from more solar radiation.

Lead in housing paints: an exposure source still not taken seriously for children lead poisoning in China.

After prohibitions on lead gasoline additives, which have proved to be a public health accomplishment world wide, many countries focus on other exposure source of children lead poisoning. Removing lead from paints is one of the important measures. Although there have been regulatory limits on lead in paints in China, evidence reported in this article indicates that lead-based paints were very common in new paints available for housing and in existing residential paints. Twenty-nine of 58 new paint samples (50%) had lead content equal to or exceeding 600 ppm, including 14 (24%) equal to or exceeding 5000 ppm. The highest sample contained 153,000 ppm lead, about 15% of the paint weight. Thirty-two new paints (55%) contained "soluble" lead exceeding 90 ppm, the current lead limit on paints in China. Of the existing paints, 16 of 28 samples of existing paint (57%) collected from 24 kindergartens and primary schools had lead concentrations equal to or exceeding 600 ppm, including six samples (21%) equal to or exceeding 5000 ppm. The highest concentration sample contained 51,800 ppm lead, accounting for 5.2% of the paint weight. It has been shown in many areas that paint lead is a major exposure source for lead poisoning in children. This is particularly true after the phasing out of lead from gasoline. Effective limitation on lead content in new paint, and lead hazard control measures directed towards existing paint, could reduce children blood lead levels (BLLs). There has been a lead standard for paints in China since 1986 and a stricter limit was introduced in recent years. Governments should take it seriously and enforce regulations, commit a long-term challenge to eliminate paint lead as it is the threat to current and the next generation.

Lead content in household paints in India.

Lead and its compounds are used in paints not only to impart colour but also to make it durable, corrosion resistant and to improve drying. Adverse health impacts of lead especially on children have led countries to restrict or ban its use in paints. While U.S. and other developed countries instituted measures to limit the use of lead in paints, some developing countries including India have failed to regulate their lead content. The present study was undertaken to determine the levels of lead in new latex (water-based) and enamel paints (oil-based) intended for residential use in India. A total of 69 paint samples (38 latex and 31 enamel samples) from six of the most popular brands were analysed for lead concentrations. While all latex paint samples contained low levels of lead, (i.e., well below 600 ppm as regulated by United States' Consumer Products Safety Commission) the enamel paint samples of all but one brand contained significant concentrations of lead, ranging up to 140,000 ppm. In fact 84% of the enamel paints tested exceeded 600 ppm whereas only 38 % of all samples (including latex and enamel types) exceeded this regulatory level.

Testing antimicrobial paint efficacy on gypsum wallboard contaminated with Stachybotrys chartarum.

The goal of this research was to reduce occupant exposure to indoor mold through the efficacy testing of antimicrobial paints. An accepted method for handling Stachybotrys chartarum-contaminated gypsum wallboard (GWB) is removal and replacement. This practice is also recommended for water-damaged or mold-contaminated GWB but is not always followed completely. The efficacy of antimicrobial paints to eliminate or control mold regrowth on surfaces can be tested easily on nonporous surfaces. The testing of antimicrobial efficacy on porous surfaces found in the indoor environment, such as gypsum wallboard, can be more complicated and prone to incorrect conclusions regarding residual organisms. The mold S. chartarum has been studied for toxin production and its occurrence in water-damaged buildings. Research to control its growth using seven different antimicrobial paints and two commonly used paints on contaminated, common gypsum wallboard was performed in laboratory testing at high relative humidity. The results indicate differences in antimicrobial efficacy for the period of testing, and that proper cleaning and resurfacing of GWB with an antimicrobial paint can be an option in those unique circumstances when removal may not be possible.

A review of surface roughness in antifouling coatings illustrating the importance of cutoff length.

Surface roughness (SR) can affect the hydrodynamic performance of antifouling (AF) coatings and influence the settlement behaviour of fouling larvae, which makes it an important parameter in the evaluation of novel coatings. This paper reviews the causes and consequences of SR in the shipping industry, the methodology used for measuring it, and the importance of measuring and reporting it correctly. SR is a parameter that originates from marine engineering, but has been used extensively by marine scientists to characterise novel coatings and to investigate microtopographies that might inhibit settlement behaviour. One of the integral components of the SR measurement is the use of a cutoff filter. This is a short-pass filter that lets the high wave-number components through and thus separates the waviness from the roughness. Depending on the length of this filter, roughness at different levels of magnification can be investigated. Much of the published work on SR of AF coatings makes no mention of cutoff length, so that the results cannot be compared. It is suggested that an international standard is needed and that if more researchers were aware of the significance of stating cutoff length when reporting SR, more interdisciplinary work between biologists, engineers and material scientists would be possible in this field.

Field-user acceptability of new camouflage face paint formulations in the Republic of Korea.

New formulations of camouflage face paint (CFP), one with 30% N,N-diethyl-3-methylbenzamide (DEET) and the other without DEET, were evaluated for soldier-user acceptability during a military field-training exercise in the Republic of Korea. Soldiers testing the CFP formulations were members of one of four U.S. Army infantry companies (A, B, C, or D). The formulations were evaluated while soldiers participated in simulated combat exercises for 5 days during hot, humid summer weather in Korea. Results showed that soldiers found both of the new formulations easier to apply (91.3% of respondents who used CFP without DEET and 87.9% of respondents who used CFP with DEET) and remove (82.6% without DEET and 81.2% with DEET) than the previous standard military-issue CFP. Soldier acceptability was higher for the new CFP formulation with 30% DEET (70.5%) than for the formulation without 30% DEET (52.9%). Soldiers recommended it more frequently (70.5%) than the formulation without 30% DEET (50.0%). The new CFP formulation with 30% DEET was rated more often (79.5%) as either good or excellent than the new formulation without 30% DEET (67.4%). Soldiers reported that the CFP formulation with 30% DEET more successfully camouflaged the face (92.7%) than the formulation without 30% DEET (80.0%).

Collaborative study for the quality control of trace element determinations in paint coatings. Part 2. Certification of alkyd resin paint reference materials for the migratable contents of trace elements (CRMs 620 and 623).

This paper describes the preparation, homogeneity studies and certification of a series of two paint reference materials (mild steel coated with alkyd resin paint, CRM620, and comminuted paint from alkyd resin paint, CRM623) which have been produced in support of the EU Toy Safety Directive (88/378/EEC). The reference materials have been certified for levels of toxic element migration using the method specified in European Standard EN71-3:1994 published by the European Committee for Standardization. As such, the certified values, indicative values and range data quoted for the reference materials in this paper are method specific and relate only to European Standard EN71-3:1994. The paper summarizes the analytical work carried out and gives a description of the analytical methods used to measure As, Ba, Cd, Cr, Hg, Pb, Sb and Se, the 8 toxic elements specified in European Standard EN71-3:1994, in the sample extracts. Descriptions of the reference materials, certified values, indicative values together with their associated uncertainties or range of laboratory means as appropriate are given. The preparation of a (not certified) reference material (beechwood coated with nitrocellulose paint, RM621) is also described and assigned values for As, Ba, Cd and Se are given. The Hg content could not be certified in any of the reference materials, owing to a high dispersion of results.