Post-chemical grafting poly(methyl methacrylate) to commercially renewable elastomer as effective modifiers for polylactide blends.

A novel poly(epichlorohydrin-co-ethylene oxide)-g-poly(methyl methacrylate) copolymer (ECO-g-PMMA) was successfully synthesized from a commercially renewable elastomer via the ATRP method. The graft copolymer was investigated as a toughening agent and compatibilizer for polylactide (PLA) and PLA/ECO blends, respectively. Binary blending PLA with the copolymers (5-15 wt%) significantly improved the strain at break of PLA above 200% without a great strength loss. More importantly, the ternary PLA/ECO/ECO-g-PMMA copolymer blends exhibited a remarkably high impact strength of 96.9 kJ/m2 with non-broken behaviors. An interesting phase structure transformation from a typical sea-island structure to a unique quasi-continuous network structure was observed with varying the content of ECO-g-PMMA from 0 to 15 wt% in the ternary blends. The native toughening mechanism analysis indicated the synergistic toughening effect of the good interfacial adhesion and unique quasi-continuous morphology endowed the ternary blends with excellent mechanical performance.

Synthesis of Block Copolymer Brush by RAFT and Click Chemistry and Its Self-Assembly as a Thin Film.

A well-defined block copolymer brush poly(glycidyl methacrylate)-graft-(poly(methyl methacrylate)-block- poly(oligo(ethylene glycol) methyl ether methacrylate)) (PGMA-g-(PMMA-b-POEGMA)) is synthesized via grafting from an approach based on a combination of click chemistry and reversible addition-fragmentation chain transfer (RAFT) polymerization. The resulting block copolymer brushes were characterized by 1H-NMR and size exclusion chromatography (SEC). The self-assembly of the block copolymer brush was then investigated under selective solvent conditions in three systems: THF/water, THF/CH3OH, and DMSO/CHCl3. PGMA-g-(PMMA-b-POEGMA) was found to self-assemble into spherical micelle structures as analyzed by transmission electron microscopy (TEM) and dynamic light scattering (DLS). The average size of the particles was much smaller in THF/CH3OH and DMSO/CHCl3 as compared with the THF/water system. Thin film of block copolymer brushes with tunable surface properties was then prepared by the spin-coating technique. The thickness of the thin film was confirmed by scanning electron microscopy (SEM). Atom force microscopy (AFM) analysis revealed a spherical morphology when the block copolymer brush was treated with poor solvents for the backbone and hydrophobic side chains. The contact angle measurements were used to confirm the surface rearrangements of the block copolymer brushes.

Effects of hydroxyapatite on PMMA-HAp cement for biomedical applications.

OBJECTIVE: The main goal of this study was to examine the influence of hydroxyapatite (HAp) macroaggreate concentrations on thermal and mechanical properties of radioactive bone cement and to study the relation of glass transition Tg with its mechanical properties. METHODS: The bone cement as (1-x)PMMA-xHAp binary system was prepared in six [x] distinct concentration parameters of 0.0 up to 0.5. The HAp was synthesized using a solgel procedure following calcination by thermal treatment. The composite was prepared in cold based (non-radioactive) mixing polymethyl methacrylate (PMMA) and HAp. Differential scanning calorimetry (DSC), thermogravimetric analysis (TGA) and mechanical compressive strength (CS) were used to measure the thermal and mechanical properties. RESULTS: The DSC and TGA thermal profiles in function to concentration parameter [x] were presented. The CS lies in a range of 3.71-7.37 MPa and the glass transition temperature Tg = 126.27 °C. There was a direct relationship between the PMMA-HAp thermoplastic properties with mechanical and thermal properties in function of HAp concentrations. CONCLUSION: The specific PMMA-HAp composite, with a concentration ratio of 1:1 and HAp thermal treatment at the Tg, provides a material with a compression strength of 7.37 MPa and a suitable amount of porous similar to a trabecular bone, possible to apply in bone cement implants, regardless of whether they are radioactive or not.

Microstructure and antibacterial efficacy of graphene oxide nanocomposite fibres.

Antibacterial polymer nanocomposite fibre meshes containing graphene oxide (GO) nanosheets were successfully prepared by pressurised gyration. The morphological and chemical composition of the resulting fibre meshes were determined using Scanning Electron Microscopy (SEM), Raman spectroscopy, Raman mapping and Fourier-Transform Infrared Spectroscopy (FT-IR). SEM showed the fibres to have an average diameter increasing from ~1-4 µm as the GO loading increased. FT-IR and Raman spectroscopy confirmed the inclusion of GO nanosheets on the fibre surface. The antibacterial potential of GO nanocomposite fibres were investigated using Escherichia coli K12. Average bacterial reduction ranged from 46 to 85 % with results favouring the strongest bioactivities of the nanocomposite containing 8 wt% of GO. Finally, bacterial toxicity of the nanocomposites was evaluated by reactive oxygen species (ROS) formation. A mechanism for the antibacterial behaviour of the nanocomposite fibres is presented. Stimulated Raman scattering imaging and spectra of the fibres post antibacterial studies showed flakes of GO distributed across the surface of the poly(methyl 2-methylpropenoate) (PMMA) fibres, which contribute to the high killing efficacy of the composites towards E. coli. GO nanosheets embedded in a polymer matrix have demonstrated the ability to retain their antibacterial properties, thus offering themselves as a promising antibacterial agent.

Absorptive and expansive behaviors of poly(methyl methacrylate-co-acrylic acid) bone cement.

Some additives had provided the expansion capacity to the polymethylmethacrylate (PMMA) bone cement and also reduced its maximum reaction temperature. However, the corresponding modified bone cement displayed inferior simulated body fluid (SBF) absorption capacity and expansion behavior, the mechanism of SBF absorption and the trend of expansion stress were ignored additionally. In this study, a homogeneous distribution of poly (methyl methacrylate-co-acrylic acid) [P(MMA-AA)] microspheres led to the formation of microchannels that favored the delivery of SBF to the interior, causing an increased absorption capacity and enhanced expansion behavior before solidification of the bone cement, with the maximum equilibrium absorption ratio and the expansion ratio reaching 27.3 % and 26.3 %, respectively, at an AA content of 50 %. In addition, the expansion stress induced by the expansion behavior experienced a gradual increase from the 0 s to 2590s, followed by a sharp climbed in a short period ranging from 2590s to 2900s, finally reaching maximum stress of 82.1 MPa. Furthermore, the expansion stress within the maximum value could be obtained by controlling the AA content in the P(MMA-AA) bone cement. With the above characteristics, the prepared P(MMA-AA) bone cement has potential applications as a filling and adhesive material in arthroplasties, vertebroplasties, joint replacements, bone screws, and dentistry.

Controlled Synthesis of Block Copolymers by Mechanistic Transformation from Atom Transfer Radical Polymerization to Iniferter Process.

A straightforward transformation protocol combining two distinct living polymerization methods for the controlled synthesis of block copolymers is described. In the first step, bromo-terminated poly(methyl methacrylate) is prepared by atom transfer radical polymerization (ATRP). Then, a bromide end group is substituted with a triphenylmethyl (trityl) functionality under visible light irradiation using dimanganese decacarbonyl (Mn2 (CO)10 ) photochemistry. The resulting polymers with trityl end groups are used as macroiniferter for the polymerization of styrene and tert-butyl acrylate (tBA) to yield desired block copolymers with narrow molecular weight distribution. Moreover, the amphiphilic copolymers with acrylic acid functionalities are obtained by the hydrolyzation of poly(tert-butyl acrylate) containing block copolymers with trifluoroacetic acid.

Electrochemical DNA Biosensing via Electrochemically Controlled Reversible Addition-Fragmentation Chain Transfer Polymerization.

Sensitive and selective sensing of biological molecules is fundamental to disease diagnosis and infectious disease surveillance. Herein, an ultrasensitive and highly selective electrochemical DNA biosensor is described by exploiting the electrochemically controlled reversible addition-fragmentation chain-transfer (eRAFT) polymerization as a signal amplification strategy and the peptide nucleic acid (PNA) probes as the recognition elements. Specifically, the PNA probes with a thiol at their 5'-terminals are anchored to a gold electrode surface (via gold-sulfur self-assembly) for sequence-specific recognition of target DNA (tDNA) fragments, of which the phosphate sites serve as the anchorages for the targeted labeling (via the well-established phosphate-Zr4+-carboxylate chemistry) of the carboxyl-group-containing chain-transfer agents (CTAs) for the succedent eRAFT polymerization, wherein the initiating radicals are generated through electrochemical reduction of aryl diazonium salts under a potentiostatic condition. In the presence of ferrocenylmethyl methacrylate (FcCH═CH2) as the monomer, the grafting of polymer chains from the CTA-anchored sites as a result of the eRAFT polymerization brings numerous electroactive Fc tags to the electrode surface, outputting a high electrochemical sensing signal even in the presence of trace amounts of tDNA fragments. Under the optimized conditions, the linear range of the described electrochemical DNA biosensor spans from 10 aM to 10 pM ( R2 = 0.998), with an attomolar detection limit (4.1 aM) being achieved. Moreover, the described electrochemical DNA biosensor is highly selective and applicable to the sensing of tDNA fragments in complex serum samples. Given its high efficiency, easy operation, and low cost, this biosensor shows great promise in real applications.

Structure-Property Relationships for Tailoring Phenoxazines as Reducing Photoredox Catalysts.

Through the study of structure-property relationships using a combination of experimental and computational analyses, a number of phenoxazine derivatives have been developed as visible light absorbing, organic photoredox catalysts (PCs) with excited state reduction potentials rivaling those of highly reducing transition metal PCs. Time-dependent density functional theory (TD-DFT) computational modeling of the photoexcitation of N-aryl and core modified phenoxazines guided the design of PCs with absorption profiles in the visible regime. In accordance with our previous work with N, N-diaryl dihydrophenazines, characterization of noncore modified N-aryl phenoxazines in the excited state demonstrated that the nature of the N-aryl substituent dictates the ability of the PC to access a charge transfer excited state. However, our current analysis of core modified phenoxazines revealed that these molecules can access a different type of CT excited state which we posit involves a core substituent as the electron acceptor. Modification of the core of phenoxazine derivatives with electron-donating and electron-withdrawing substituents was used to alter triplet energies, excited state reduction potentials, and oxidation potentials of the phenoxazine derivatives. The catalytic activity of these molecules was explored using organocatalyzed atom transfer radical polymerization (O-ATRP) for the synthesis of poly(methyl methacrylate) (PMMA) using white light irradiation. All of the derivatives were determined to be suitable PCs for O-ATRP as indicated by a linear growth of polymer molecular weight as a function of monomer conversion and the ability to synthesize PMMA with moderate to low dispersity (dispersity less than or equal to 1.5) and initiator efficiencies typically greater than 70% at high conversions. However, only PCs that exhibit strong absorption of visible light and strong triplet excited state reduction potentials maintain control over the polymerization during the entire course of the reaction. The structure-property relationships established here will enable the application of these organic PCs for O-ATRP and other photoredox-catalyzed small molecule and polymer syntheses.

Tandem Lewis Pair Polymerization and Organocatalytic Ring-Opening Polymerization for Synthesizing Block and Brush Copolymers.

Lewis pair polymerization is a powerful method for preparing soluble polymers bearing pendant active vinyl groups by directly polymerizing dissymmetric divinyl polar monomers. Herein, we present a strategy for synthesizing block and brush copolymers via tandem Lewis pair polymerization of methacrylates, "thiol-ene" click reaction and organocatalytic ring-opening polymerization of lactide.

Facile Synthesis of Gadolinium Chelate-Conjugated Polymer Nanoparticles for Fluorescence/Magnetic Resonance Dual-Modal Imaging.

Fluorescence (FL)/magnetic resonance (MR) dual-modal imaging nanoprobes are significant not only for cutting edge research in molecular imaging, but also for clinical diagnosis with high precision and accuracy. However, synthesis of FL/MR dual-modal imaging nanoprobes that simultaneously exhibit strong fluorescent brightness and high MR response, long-term colloidal stability with uniform sizes, good biocompatibility and a versatile surface functionality has proven challenging. In this study, the well-defined core-shell structured Gd3+ chelate-conjugated fluorescent polymer nanoparticles (Gd-FPNPs) that consist of rhodamine B (RB)-encapsulated poly(methyl methacrylate) (PMMA) cores and Gd3+ chelate-conjugated branched polyethylenimine (PEI) shells, are facilely synthesized via a one-step graft copolymerization of RB-encapsulated MMA from PEI-DTPA-Gd induced by tert-butyl hydroperoxide (TBHP) at 80 °C for 2 h. The mild synthesis route not only preserves the chemical environment for Gd3+ coordination, but also improves optical properties and chemo-/photostability of RB. A high local concentration of outer surface-chelated Gd3+ and their direct interactions with hydrogen protons endow Gd-FPNPs high longitudinal relaxivity (26.86 mM-1 s-1). The uniform spherical structure of Gd-FPNPs facilitates their biotransfer, and their surface carboxyl and amine groups afford them both long-term colloidal stability and cell-membrane permeability. The excellent biocompatibility and FL/MR dual-modal imaging capability of Gd-FPNPs are demonstrated using HeLa cells and mice as models. All the results confirm that Gd-FPNPs fulfill the design criteria for a high-performance imaging nanoprobe. In addition, this study enables such probes to be prepared also by those not skilled in nanomaterial synthesis, and thus promoting the development of novel functional imaging nanoprobes.

A new style for synthesis of thermo-responsive Fe3O4/poly (methylmethacrylate-b-N-isopropylacrylamide-b-acrylic acid) magnetic composite nanosphere and theranostic applications.

In this work, a novel thermo-responsive Fe3O4/poly(methylmethacrylate-b-N-isopropylacrylamide-b-acrylic acid) magnetic composite nanosphere was synthesized for anticancer drug delivery applications. For this propose, the poly(methylmethacrylate-b-N-isopropylacrylamide-b-acrylic acid) [poly (MMA-b-NIPAAm-b-AAc)] was synthesized via reversible addition-fragmentation transfer method. The physic-chemical characterization of the Fe3O4/poly(MMA-b-NIPAAm-b-AAc) magnetic composite nanosphere was investigated by FTIR, HNMR spectroscopies and GPC, FESEM, XRD, VSM and DLS. The thermo-sensitivity of the Fe3O4/P(MMA-b-NIPAAm-b-AAc) magnetic composite nanosphere was confirmed via DLS at 40 °C. DOX encapsulation efficiency was calculated to be 98.2%. The effect of temperature and pH on release behaviors of stimuli responsive DOX-loaded Fe3O4/P(MMA-b-NIPAAm-b-AAc)] magnetic composite nanosphere were investigated. The release rate at pH 7.4, 5.4 and 4 (T = 37 °C) was reached about 24.4, 42.4 and 57.5 wt%, after 4-5 day. The release rate improved at tumor simulated environment (t:40 °C and pH ≤ 5.4). The cytotoxic effects of the magnetic composite nanosphere were appraised by MTT assay and the results indicated that novel developed smart nanocomposite here was nontoxic to MCF-7 cells and can be applied as anti-cancer drug delivery system. Also, the results of the Cellular uptake of MCF7 cells treated with rhodamine labeled DOX-loaded nanocarrier for 2 h have indicated that DOX can be applied as cytotoxic agent and targeting ligand.

The antifungal effects and mechanical properties of silver bromide/cationic polymer nano-composite-modified Poly-methyl methacrylate-based dental resin.

Poly-methyl methacrylate (PMMA)-based dental resins with strong and long-lasting antifungal properties are critical for the prevention of denture stomatitis. This study evaluated the antifungal effects on Candida albicans ATCC90028, the cytotoxicity toward human dental pulp cells (HDPCs), and the mechanical properties of a silver bromide/cationic polymer nano-composite (AgBr/NPVP)-modified PMMA-based dental resin. AgBr/NPVP was added to the PMMA resin at 0.1, 0.2, and 0.3 wt%, and PMMA resin without AgBr/NPVP served as the control. Fungal growth was inhibited on the AgBr/NPVP-modified PMMA resin compared to the control (P < 0.05), and the antifungal activity increased as the incorporation of the AgBr/NPVP antimicrobial composite increased. Confocal laser scanning microscopy (CLSM) showed that the number of fungal cells attached to the modified PMMA resin was considerably lower than in the control. The relative growth rate of HDPCs of modified groups were higher than 75%. The flexural strength (FS) and flexural modulus (FM) were not significantly different (P > 0.05) between the experimental and control groups. These data indicate that the incorporation of AgBr/NPVP conferred strong and long-lasting antifungal effects against Candida albicans to the PMMA resin, and it has low toxicity toward HDPCs, and its mechanical properties were not significantly affected.

Electrospinning of poly(glycerol sebacate)-based nanofibers for nerve tissue engineering.

Nerve tissue engineering (TE) requires biomimetic scaffolds providing essential chemical and topographical cues for nerve regeneration. Poly(glycerol sebacate) (PGS) is a biodegradable and elastic polymer that has gained great interest as a TE scaffolding biomaterial. However, uncured PGS is difficult to be electrospun into nanofibers. PGS would, therefore, require the addition of electrospinning agents. In this study, we modified PGS by using atom transfer radical polymerization (ATRP) to synthesize PGS-based copolymers with methyl methacrylate (MMA). The synthesized PGS-PMMA copolymer showed a molecular weight of 82kDa and a glass transition temperature of 115°C. More importantly, the PGS-PMMA could be easily electrospun into nanofiber with a fiber diameter of 167±33nm. Blending gelatin into PGS-PMMA nanofibers was found to increase its hydrophilicity and biocompatibility. Rat PC12 cells were seeded onto the PGS-PMMA/gelatin nanofibers to investigate their potential for nerve regeneration. It was found that gelatin-containing PGS-based nanofibers promoted cell proliferation. The elongated cell morphology observed on such nanofibers indicated that the scaffolds could induce the neurite outgrowth of the nerve stem cells. Overall, our study suggested that the synthesis of PGS-based copolymers might be a promising approach to enhance their processability, and therefore advancing bioscaffold engineering for various TE applications.

Preparation and characterization of ZnO-PMMA resin nanocomposites for denture bases.

PURPOSE: The aim of the paper was to investigate the antifungal activity of zinc oxide nanoparticles (ZnONPs) against Candida albicans. Some attempts have been made to find out the best way to introduce ZnONPs into polymethyl methacrylate (PMMA) resin material and to determine some parameters of a newly formed composite. MATERIAL AND METHODS: Zinc oxide nanoparticles were manufactured and their basic physical parameters were determined (average particle size, density, specific surface area). Minimal inhibitory concentration (MIC) of ZnONPs was determined for the Candida albicans standard strain. The average size of ZnO conglomerates in the monomer solution of PMMA resin was measured using a dynamic light scattering instrument. PMMA resin samples with incorporated ZnONPs were produced. The morphology of nanopowder and the newly formed composite was examined under a scanning electron microscope (SEM). In addition, the roughness parameter of PMMA resin material was investigated before and after ZnONPs modification. RESULTS: Nanopowder with the average particle size of 30 nm, density of 5.24 g/cm3 and surface area of 39 m2/g was obtained. MIC was determined at the level of 0.75 mg/mL. The average size of ZnO conglomerates in the monomer solution of acrylic resin dropped by 11 times after ultrasound activation. SEM examination of a newly formed composite showed a successful introduction of ZnONPs confirmed by the energy dispersive X-ray spectroscopy (EDS) analysis. There were no statistically significant differences in the biomaterial roughness before and after the modification of ZnONPs. CONCLUSION: Zinc oxide nanoparticles were successfully incorporated into acrylic resin used for the production of denture bases. The presence of nanoparticles with sizes below 100 nm was confirmed. Nevertheless a newly created composite needs to be further investigated to improve its homogeneity, and to check its microbiological properties, strength and biocompatibility prior to its possible clinical use.

On the Termination Mechanism in the Radical Polymerization of Acrylates.

In a recent publication, Nakamura and co-workers studied the termination mechanism in the radical polymerization of acrylates. Contrary to conventional thinking, their conclusion is that termination is overwhelmingly by disproportionation. This finding impacts on a large body of the previous work in the polymerization of acrylic monomers which this work seeks to address. Analysis of the molecular weight distribution of acrylic polymers obtained under different polymerization conditions shows that termination by combination is the more probable mechanism for mutual termination of secondary radicals. It is proposed that in the experiments conducted by Nakamura and co-workers, backbiting plays a key role and their experimental data are reinterpreted, showing that they are more revealing with respect to the mode of termination of the midchain radical produced by backbiting, than to bimolecular termination of secondary radicals.

One-step method for the preparation of poly(methyl methacrylate) modified titanium-bioactive glass three-dimensional scaffolds for bone tissue engineering.

A novel three-dimensional (3D) titanium (Ti)-doping meso-macroporous bioactive glasses (BGs)/poly(methyl methacrylate) (PMMA) composite was synthesised using PMMA and EO20PO70EO20 (P123) as the macroporous and mesoporous templates, respectively. Unlike the usual calcination method, the acid steam technique was used to improve the polycondensation of Ti-BGs, and then PMMA was partially extracted via chloroform to induce the macroporous structure. Simultaneously, the residual PMMA which remained in the wall enhanced the compressive strength to 2.4 MPa (0.3 MPa for pure BGs). It is a simple and green method to prepare the macro-mesoporous Ti-BGs/PMMA. The materials showed the 3D interconnected hierarchical structure (250 and 3.4 nm), making the fast inducing-hydroxyapatite growth and the controlled drug release. Besides mentioned above, the good antimicrobial property and biocompatible of the scaffold also ensure it is further of clinical use. Herein, the fabricated materials are expected to have potential application on bone tissue regeneration.

Low auto-fluorescence fabrication methods for plastic nanoslits.

Plastic nanofluidic devices are becoming increasingly important for biological and chemical applications. However, they suffer from high auto-fluorescence when used for on-chip optical detection. In this study, the auto-fluorescence problem of plastic nanofluidic devices was remedied by newly developed fabrication methods that minimise their auto-fluorescence: one by depositing a gold (Au) layer on them, the other by making them ultra-thin. In the first method, the Au layer [minimum thickness is 40 nm on 150 µm SU-8, 50 nm on 1 mm polyethylene terephthalate (PET), and 40 on 2 nm polymethyl methacrylate (PMMA)] blocks the auto-fluorescence of the polymer; in the second method, auto-fluorescence is minimised by making the chips ultra-thin, selected operating thickness of SU-8 is 20 µm, for PET it is 150 µm, and for PMMA it is 0.8 mm.

Supercritical Fluid-Driven Polymer Phase Separation for Microlens with Tunable Dimension and Curvature.

Microlenses are highly sought as reliable means for high-resolution optical imaging at low illumination intensities. Plano-convex configuration with tunable dimension and curvature is an essential feature in the microlens fabrication. In this study, we present a facile and green route for preparing well-defined microlenses based on polymer phase separation in the presence of supercritical carbon dioxide (scCO2). The behaviors of linear polymethylmethacrylate protruded from cross-linked silicone network in scCO2 environment are investigated from the perspectives of thermodynamics and kinetics. Microlenses with dimensions from 2 to 15 µm and contact angles from 55° to 112° are successfully obtained through the adjustment of the kinetic conditions and outgassing rate. With the tunable focal length, they exhibit intrinsic function of discerning submicroscale patterns that are unable to be observed directly under optical microscope. Moreover, size confinement on the substrate results in the generation of well-ordered microlens arrays, affording great promise for applications in bioimaging, photolithography, light harvesting, and optical nanosensing.

Covalent Modification of MoS2 with Poly(N-vinylcarbazole) for Solid-State Broadband Optical Limiters.

New soluble MoS2 nanosheets covalently functionalized with poly(N-vinylcarbazole) (MoS2-PVK) were in situ synthesized for the first time. In contrast to MoS2 and MoS2 /PVK blends, both the solution of MoS2 -PVK in DMF and MoS2-PVK/poly(methyl methacrylate) (PMMA) film show superior nonlinear optical and optical limiting responses. The MoS2-PVK/PMMA film shows the largest nonlinear coefficients (ßeff) of about 917 cm GW(-1) at λ=532 nm (cf. 100.69 cm GW(-1) for MoS2/PMMA and 125.12 cm GW(-1) for MoS2/PVK/PMMA) and about 461 cm GW(-1) at λ=1064 nm (cf. -48.92 cm GW(-1) for MoS2/PMMA and 147.56 cm GW(-1) for MoS2/PVK/PMMA). A larger optical limiting effect, with thresholds of about 0.3 GW cm(-2) at λ=532 nm and about 0.5 GW cm(-2) at λ=1064 nm, was also achieved from the MoS2-PVK/PMMA film. These values are among the highest reported for MoS2-based nonlinear optical materials. These results show that covalent functionalization of MoS2 with polymers is an effective way to improve nonlinear optical responses for efficient optical limiting devices.