Examining gaze behavior in undergraduate students and educators during the evaluation of tooth preparation: an eye-tracking study.

BACKGROUND: Gaze behavior can serve as an objective tool in undergraduate pre-clinical dental education, helping to identify key areas of interest and common pitfalls in the routine evaluation of tooth preparations. Therefore, this study aimed to investigate the gaze behavior of undergraduate dental students and dental educators while evaluating a single crown tooth preparation. METHODS: Thirty-five participants volunteered to participate in the study and were divided into a novice group (dental students, n = 18) and an expert group (dental educators, n = 17). Each participant wore a binocular eye-tracking device, and the total duration of fixation was evaluated as a metric to study the gaze behavior. Sixty photographs of twenty different tooth preparations in three different views (buccal, lingual, and occlusal) were prepared and displayed during the experimental session. The participants were asked to rate the tooth preparations on a 100 mm visual analog rating scale and were also asked to determine whether each tooth preparation was ready to make an impression. Each view was divided into different areas of interest. Statistical analysis was performed with a three-way analysis of the variance model with repeated measures. RESULTS: Based on the participants' mean rates, the "best" and the "worst" tooth preparations were selected for analysis. The results showed a significantly longer time to decision in the novices compared to the experts (P = 0.003) and a significantly longer time to decision for both the groups in the best tooth preparation compared to the worst tooth preparation (P = 0.002). Statistical analysis also showed a significantly longer total duration of fixations in the margin compared to all other conditions for both the buccal (P < 0.012) and lingual (P < 0.001) views. CONCLUSIONS: The current study showed distinct differences in gaze behavior between the novices and the experts during the evaluation of single crown tooth preparation. Understanding differences in gaze behavior between undergraduate dental students and dental educators could help improve tooth preparation skills and provide constructive customized feedback.

Restauração em resina composta semidireta em dente posterior: relato de caso / Semi-direct composite restoration in posterior toth: a case report

A escolha da técnica restauradora desempenha papel fundamental na eficácia e duração de um tratamento reabilitador. O objetivo deste relato de caso foi descrever a utilização da técnica semidireta para a confecção de uma restauração em resina composta em um primeiro molar inferior. A paciente apresentava uma restauração insatisfatória no dente 36, que necessitava ser substituída devido à infiltração por cárie. Optou-se pela técnica semidireta devido à amplitude da cavidade, que envolvia estruturas de suporte, e pela combinação das vantagens das abordagens direta e indireta. O procedimento envolveu a remoção de tecido cariado, a aplicação de hidróxido de cálcio pasta, seguida da aplicação de uma fina camada de ionômero de vidro e, posteriormente, resina fluída para realizar o selamento dentinário. O preparo foi realizado seguindo os princípios necessários. O elemento em questão foi moldado com silicone de adição e o arco antagonista, com alginato. Ambos modelos foram vertidos com silicone para modelos semirrígidos e montados em oclusor de peças de brinquedo. A restauração semidireta foi confeccionada em resina composta Filtek Z350 XT, respeitando a anatomia do dente 36. Pigmentos foram utilizados para aprimorar detalhes estéticos. Após acabamento e polimento, a peça foi condicionada e cimentada com cimento dual Relyx Ultimate. Pode-se concluir que a abordagem restauradora por meio da técnica semidireta construída em modelo semirrígido é uma opção terapêutica conservadora e vantajosa para dentes com extensa destruição coronária. Essa técnica possibilita a restauração de forma eficaz, garantindo tanto a estética quanto a função adequada do dente afetado(AU)

The choice of restorative technique plays a fundamental role in the effectiveness and duration of rehabilitation treatment. The objective of this case report was to describe the use of the semi-direct technique to create a composite resin restoration in a lower first molar. The patient had an unsatisfactory restoration on tooth 36, which needed to be replaced due to cavity infiltration. The semi-direct technique was chosen due to the amplitude of the cavity, which involved support structures, and the combination of advantages of the direct and indirect approaches. The procedure involved the removal of carious tissue, and the application of calcium hydroxide paste, followed by the application of a thin layer of glass ionomer and, subsequently, fluid resin to seal the dentin. The preparation was carried out following the necessary principles. The element in question was molded with addition silicone and the antagonist arch was molded with alginate. Both models were poured with silicone for semi-rigid models and mounted on toy parts occluders. The semi-direct restoration was made in Filtek Z350 XT composite resin, respecting the anatomy of tooth 36. Pigments were used to improve aesthetic details. After finishing and polishing, the piece was conditioned and cemented with Relyx Ultimate dual cement. It can be concluded that the restorative approach using the semi-direct technique built on a semi-rigid model is a conservative and advantageous therapeutic option for teeth with extensive coronal destruction. This technique allows for effective restoration, ensuring both the aesthetics and adequate function of the affected tooth(AU)

Evaluating the feasibility of using augmented reality for tooth preparation.

OBJECTIVES: Tooth preparation is complicated because it requires the preparation of an abutment while simultaneously predicting the ideal shape of the tooth. This study aimed to develop and evaluate a system using augmented reality (AR) head-mounted displays (HMDs) that provide dynamic navigation capabilities for tooth preparation. METHODS: The proposed system utilizes optical see-through HMDs to overlay digital information onto the real world and enrich the user's environment. By integrating tracking algorithms and three-dimensional modeling, the system provides real-time visualization and navigation capabilities during tooth preparation by using two different visualization techniques. The experimental setup involved a comprehensive analysis of the distance to the surface and cross-sectional angles between the ideal and prepared teeth using three scenarios: traditional (without AR), overlay (AR-assisted visualization of the ideal prepared tooth), and cross-sectional (AR-assisted visualization with cross-sectional views and angular displays). RESULTS: A user study (N = 24) revealed that the cross-sectional approach was more effective for angle adjustment and reduced the occurrence of over-reduction. Additional questionnaires revealed that the AR-assisted approaches were perceived as less difficult, with the cross-sectional approach excelling in terms of performance. CONCLUSIONS: Visualization and navigation using cross-sectional approaches have the potential to support safer tooth preparation with less overreduction than traditional and overlay approaches do. The angular displays provided by the cross-sectional approach are considered helpful for tooth preparation. CLINICAL SIGNIFICANCE: The AR navigation system can assist dentists during tooth preparation and has the potential to enhance the accuracy and safety of prosthodontic treatment.

Restablecimiento de guía anterior con restauraciones adhesivas / Reestablishing of anterior guidance with adhesive restorations

La estética ha llegado a formar una parte muy importante en la odontología actual. Sin embargo, no debemos sobreponer las necesidades estéticas sobre las necesidades funcionales. La pérdida de estructura dental asociada a bruxismo puede ser considerada patológica cuando compromete la guía anterior, la cual es la influencia en los movimientos mandibulares que proveen las superficies contactantes de los dientes maxilares anteriores con los mandibulares anteriores y evita contactos excéntricos dañinos en los dientes posteriores. El objetivo de este reporte de caso es presentar una alternativa conservadora para restablecer tanto la estética como la funcionalidad de una paciente de 34 años de edad que acudió a la Clínica de Prostodoncia de la Universidad Autónoma de Guadalajara en busca de rehabilitación estética de dientes anteriores. Una vez realizada su evaluación inicial se llegó al diagnóstico de pérdida de guía anterior por desgaste patológico asociado a bruxismo. El tratamiento incluyó tratamientos de conductos, remoción de caries y restauraciones mal ajustadas, coronas y carillas para restablecer la guía anterior. Se cumplieron con las expectativas estéticas que tenía la paciente al igual que con las necesidades funcionales que fueron objetivo desde el inicio, logrando un restablecimiento de la guía anterior de manera conservadora (AU)

Esthetics has become a very important part of dentistry today. However, we should not superimpose esthetic needs over functional needs. The loss of tooth structure associated with bruxism can be considered pathologic when it compromises the anterior guidance, which is the influence on mandibular movements that provides the contacting surfaces of the maxillary anterior teeth with the mandibular anterior teeth and avoids damaging eccentric contacts in the posterior teeth. The aim of this case report is to present a conservative way to restore both esthetics and function in a 34-year-old patient who came to the Prosthodontics Clinic of the Universidad Autónoma de Guadalajara in search of an esthetic appearance of her anterior teeth. After her initial evaluation, a diagnosis of anterior guide loss due to pathological wear associated with bruxism was made. Treatment included root canal treatment, removal of caries, and ill-fitting restorations, crowns, and veneers to reestablish the anterior guidance. The aesthetic expectations of the patient have met as well as the functional needs that were aimed from the beginning, achieving a conservative reestablishment of the anterior guidance system (AU)

Automated scoring and augmented reality visualization software program for evaluating tooth preparations.

STATEMENT OF PROBLEM: Tooth preparation is an essential part of prosthetic dentistry; however, traditional evaluation methods involve subjective visual inspection that is prone to examiner variability. PURPOSE: The purpose of this study was to investigate a newly developed automated scoring and augmented reality (ASAR) visualization software program for evaluating tooth preparations. MATERIAL AND METHODS: A total of 122 tooth models (61 anterior and 61 posterior teeth) prepared by dental students were evaluated by using visual assessments that were conducted by students and an expert, and auto assessment that was performed with an ASAR software program by using a 3-dimensional (3D) point-cloud comparison method. The software program offered comprehensive functions, including generating detailed reports for individual test models, producing a simultaneous summary score report for all tested models, creating 3D color-coded deviation maps, and forming augmented reality quick-response (AR-QR) codes for online data storage with AR visualization. The reliability and efficiency of the evaluation methods were measured by comparing tooth preparation assessment scores and evaluation time. The data underwent statistical analysis using the Kruskal-Wallis test, followed by Mann-Whitney U tests for pairwise comparisons adjusted with the Benjamini-Hochberg method (α=.05). RESULTS: Significant differences were found across the evaluation methods and tooth types in terms of preparation scores and evaluation time (P<.001). A significant difference was observed between the auto- and student self-assessment methods (P<.001) in scoring both the anterior and posterior tooth preparations. However, no significant difference was found between the auto- and expert-assessment methods for the anterior (P=.085) or posterior (P=.14) tooth preparation scores. Notably, the auto-assessment method required significantly shorter time than the expert- and self-assessment methods (P<.001) for both tooth types. Additionally, significant differences in evaluation time between the anterior and posterior tooth were observed in both self- and expert-assessment methods (P<.001), whereas the evaluation times for both the tooth types with the auto-assessment method were statistically similar (P=.32). CONCLUSIONS: ASAR-based evaluation is comparable with expert-assessment while exhibiting significantly higher time efficiency. Moreover, AR-QR codes enhance learning and training experiences by facilitating online data storage and AR visualization.

Preparation of ultrathin translucent zirconia laminate veneers using 3D printing reduction guides.

Minimizing and controlling the amount of tooth reduction during the preparation of ultrathin laminate veneers is a challenge for minimally invasive dentistry. The use of reduction guides is advised to reach the optimal space required for the definitive restoration without excessive reduction. The digital production of a reduction guide used to control tooth preparation for ultrathin laminate veneers is described.

Effect of ceramic materials and tooth preparation design on computer-aided design and computer-aided manufacturing endocrown adaptation and retentive strength: An in vitro study.

OBJECTIVES: To evaluate how various tooth preparation designs impact the adaptation-both at the margins and internally-and the retentive strength of computer-aided design and computer-aided manufacturing (CAD/CAM) produced endocrowns. MATERIALS AND METHODS: 60 extracted human mandibular first molars were endodontically treated and assigned into three groups (n = 20) according to the tooth preparation design: Group N: butt joint design, Group F and F1 received 1- and 2-mm circumferential ferrule preparation, respectively. Endocrowns were milled using either lithium disilicate glass-ceramic (IPS emax ceramic) or monolithic zirconia. The internal and marginal adaptation of the endocrowns were evaluated using the replica technique. After cementation, the endocrowns of all test groups were dislodged axially at 0.5 mm/min using a universal testing machine. A 2-way ANOVA and the independent samples t-test (α = .05) were performed to statistically analyze the data. RESULTS: The effect of changing the design of the tooth preparation (butt joint, ferrule) on the marginal and internal gap was shown to be statistically significant (p < .05); the lower gap values were recorded at the axial followed by cervical, marginal, and pulpal floor walls in both ceramic groups regardless of the teeth preparation design. The ANOVA test revealed similar average removal forces and stresses for the two types of tested ceramic materials. CONCLUSION: IPS emax ceramic adapted better than monolithic zirconia ceramic, regardless of the preparation design. Ferrule preparation design is more retentive than butt joint preparation, regardless of the type of ceramic material used.

Zirconia restoration types, properties, tooth preparation design, and bonding. A narrative review.

OBJECTIVE: The purpose of this review was to provide dental professionals with information regarding the various types of zirconia restorations, their mechanical and optical properties, tooth preparation design, and bonding protocol in an effort to enhance the longevity and durability of zirconia restorations. OVERVIEW: The yttria content of zirconia ceramics determines their classification. The mechanical and optical properties of each type are discussed, with an emphasis on the effect of yttria concentration on the properties of zirconia. The processing and sintering methods are also discussed as they have a direct impact on the properties of zirconia. The design of tooth preparation, specifically occlusal reduction, varies depending on the type of zirconia used in each case. Finally, a protocol for zirconia restoration bonding is described to ensure optimal bonding to the tooth structure. CONCLUSION: Not all zirconia restorations are the same. The selection of zirconia type based on yttria concentration, processing and sintering methods, tooth preparation design, and adherence to the bonding protocol are all critical to the success and longevity of zirconia restorations. CLINICAL SIGNIFICANCE: Zirconia restorations are the most commonly used indirect restorative material. The selection of the most appropriate zirconia type based on its yttria content, which determines its strength and translucency, is critical to the success and the longevity of the restoration. Tooth preparation design also influences the strength and translucency of the zirconia. Air-borne particle abrasion, followed by a ceramic primer and resin cement, can ensure a durable bond to the tooth structure.

Clinical management of vital and non-vital discolored tooth preparation stump shades: A clinical case series.

OBJECTIVE: Traditional and modern-day laboratory techniques can be used to mask vital and non-vital discolored teeth. CLINICAL CONSIDERATIONS: Two clinical case reports are presented showing different treatment approaches to differing clinical scenarios of partial coverage veneer and full coverage crown restorations, respectively. CONCLUSIONS: Feldspathic ceramics should be considered when customization of stump shade correction and equalization is required with minimum facial reduction with veneer restorations. Translucent zirconia (5 mol% Y2 O3 ) can be used to mask metal posts and core restorations on non-vital teeth using an opaquer material that is infused into the intaglio surface in the green state. CLINICAL SIGNIFICANCE: Different clinical scenarios will present to the clinician in regard to discolored stump shades where understanding what laboratory material treatment options are available that will help guide definitive restoration types and ultimately tooth preparation design.

[Non-retentive adhesive restorations]. / Niet-retentieve adhesieve restauraties.

With the advent of adhesive dentistry, tooth preparation can be minimally invasive. An optimal adhesion to the dental tissues is a requirement. Rubberdam isolation, using a gold standard adhesive and bonding to freshly prepared dentin are all factors that improve the adhesion to tooth tissue. For non-retentive restorations, indirect composite and glass-ceramic materials are suitable. To date, several studies have shown a high survival rate of indirect adhesive restorations. The adage "if you can isolate the tooth, you can preserve it" may guide the choice of starting an adhesive procedure.

Influencia de la Morfología Externa de la Raíz de Primeros Premolares Superiores en la Sobreestimación del Espesor Radiográfico Radicular Durante la Preparación para Poste, Evaluados Mediante Tomografía Computarizada Cone Beam / Influence of the External Morphology of the Root of Upper First Premolars on the Overestimation of Radiographic Root Thickness During Post Preparation, Evaluated by Cone Beam Computed Tomography

La investigación tuvo como objetivo determinar la influencia de la morfología externa de la raíz de primeros premolares superiores en la existencia de sobreestimación radiográfica durante la preparación para poste. Con este fin se realizó un estudio transversal in vitro, donde 60 premolares superiores uniradiculares fueron instrumentadas con fresas Gates Glidden y Pesso de calibre 1, 2 y 3. Seguidamente se obtuvieron imágenes radiográficas digitales de cada pieza dentaria mediante un aparato posicionador a una distancia constante en sentido vestíbulo lingual, asimismo se realizaron imágenes tomográficas volumétricas de las muestras. En ambas técnicas imagenológicas se midió el espesor a mesial y distal de las piezas. La sobreestimación fue calculada mediante la diferencia de la medida tomográfica menos la radiográfica. Los resultados indicaron que en ambas paredes radiculares hubo diferencia significativa entre las medidas radiográficas y tomográficas (p<0,05), encontrándose en la pared distal diferencias altamente significativas (p<0,001); además se evidenció que la sobreestimación radiográfica fue mayor en la pared distal. El estudio concluyó que existe sobreestimación radiográfica en premolares superiores durante la preparación para poste de un 20,42 % en promedio, siendo la pared distal la estructura que presenta mayor sobreestimación.

SUMMARY: he investigation´s objective was to determine the influence of external morphology of the root of upper first premolars in the existence of radiographic overestimation during preparation for post. An in vitro cross-sectional study was carried out, where 60 single-rooted upper premolars were instrumented with burs. Gates Glidden and Pesso of caliber 1, 2 and 3, then, digital radiographic images of each dental piece were obtained by means of a positioning device at a constant distance in the buccolingual direction; volumetric tomographic images of the samples were also performed. In both imaging techniques, the mesial and distal thickness of the pieces was measured. The overestimation was calculated by the difference of the tomographic measurement minus the radiographic one. The results indicated that in both root walls there was a significant difference between the radiographic and tomographic measurements (p<0.05), with highly significant differences being found in the distal wall (p<0.001); In addition, it was evidenced that the radiographic overestimation was greater in the distal wall. The study concluded that there is radiographic overestimation in upper premolars during post preparation of 20.42% on average, with the distal wall being the structure that presents the greatest overestimation.

Simultaneous implantation and tooth preparation technology guided by 3D-printed guide.

Using digital technologies in concurrently performing missing tooth implantation and preparation of remaining teeth is a solution to reduce the number of visits and improve efficiency. This paper proposes a digital process for simultaneously implanting and preparing teeth. It integrates implant surgical guide and 3D-printed tooth preparation guide into a single guide and completes guided implant placement and precise tooth preparation. Based on "repair-oriented" virtual implant planning, the implant surgical guide can improve the efficiency and predictability of implant placement, and its linear accuracy is about 1 mm. The tooth preparation guide precisely guides tooth preparation and restoration space visualization, ensuring the quality of the tooth preparation. The two guides have different design accuracy requirements, and thus their combination improves the overall guiding accuracy requirements. The concurrent application of the two guides minimizes the clinical operation time, number of visits, and economic burden of patients.

Veneer tooth preparation utilizing a novel digital designed workflow: A case report.

OBJECTIVE: This article describes a technique to implement guided tooth preparation where the tooth is virtually prepared in the laboratory and preparation templates are created for chairside use. CLINICAL CONSIDERATIONS: Prior to any tooth preparation, patient records are acquired with an intra-oral scanner, both stump and final shades are selected, and digital photos are taken. These digital records are used in combination with digital laboratory tools to do the virtual preparation first, and then to provide chairside templates for guided tooth preparation. CONCLUSIONS: The traditional approach of tooth preparation has evolved from historically preparing a tooth without any pretreatment guidance to, more currently, preparing the tooth through a mock-up of the desired final restoration. The outcome of these traditional approaches is highly dependent on the operator's skills to produce a successful outcome, and often resulted in more tooth structure removal than necessary. However, CAD/CAM technology now offers a guided tooth approach to tooth preparation which minimizes tooth structure removal and provides an advantage to the beginner dentist. CLINICAL SIGNIFICANCE: This is a unique approach in digital restorative dentistry.

Effect of cement gap and drill offset on the marginal and internal fit discrepancies of crowns designed with different tooth preparations.

AIM: The aim of the present study was to evaluate the effect of cement gap and drill offset on the marginal and internal fit discrepancies of crowns designed with different tooth preparations. MATERIALS AND METHODS: Five tooth preparations were constructed, and crowns with different cement gaps and drill offsets were obtained. Then, best-fit alignment was performed on the crowns with the corresponding tooth preparations, and the fit discrepancies were expressed by color-coded difference images and root mean square (RMS) values. The RMS values of each group were analyzed by the rank-based Scheirer-Ray-Hare test (α = 0.05). RESULTS: The color segments in the sharp line angles area of the Sharp line angles group changed significantly before and after the drill offset. The cement gap had a significant effect on the marginal, internal, or overall fit discrepancies of the five design groups (P < 0.001), while the drill offset had a significant effect on the marginal fit discrepancies of the Shoulder-lip group and the internal or overall fit discrepancies of the Sharp line angles group (P < 0.001). Additionally, the interaction effect between cement gap and drill offset was significant for the marginal fit discrepancies of the Shoulder-lip group and the internal or overall fit discrepancies of the Sharp line angles group (P < 0.01). CONCLUSIONS: The cement gap and drill offset had a significant adverse effect on the marginal or internal fit discrepancies of the crowns designed with the shoulder-lip and sharp line angles designs. Tooth preparation designs with intense curvature changes such as shoulder-lip and sharp line angles should be avoided clinically.

Impact of marginal defects on the accuracy of automated finish line detection in tooth preparation.

AIM: The present study aimed to evaluate the accuracy of automated detection of preparation finish lines in teeth with defective margins. MATERIALS AND METHODS: An extracted first molar was prepared for a full veneer crown, and marginal defects were created and scanned (discontinuity of finish line: 0.5, 1.0, and 1.5 mm; additional line angle: connected, partially connected, and disconnected). Six virtual defect models were entered into CAD software and the preparation finish line was designated by 20 clinicians (CAD-experienced group: n = 10; CAD-inexperienced group: n = 10) using the automated finish line detection method. The accuracy of automatic detection was evaluated by calculating the 3D deviation of the registered finish line. The Kruskal-Wallis and Mann-Whitney U tests were used for between-group comparisons (α = 0.05). RESULTS: The deviation values of the registered finish lines were significantly different according to conditions with different amounts of finish line discontinuity (P < 0.001). There was no statistical difference in the deviation of the registered finish line between models with additional line angles around the margin. Moreover, no statistical difference was found in the results between CAD-experienced and CAD-inexperienced operators. CONCLUSIONS: The accuracy of automated finish line detection for tooth preparation can differ when the finish line is discontinuous. The presence of an additional line angle around the preparation margin and prior experience in dental CAD software do not affect the accuracy of automated finish line detection.

The effect of different tooth preparation finishing procedures and immediate dentin sealing on the scanning accuracy of different intraoral scanners.

PURPOSE: To measure the effect of different tooth preparation finishing procedures (super-coarse grit, fine grit, and air-particle abrasion) and immediate dentin sealing (IDS) on the scanning accuracy of 4 intraoral scanners (IOSs). MATERIAL AND METHODS: A tooth preparation for a full-coverage restoration was performed on an extracted mandibular molar using super-coarse diamond burs. Four groups were created depending on the tooth preparation finishing procedure: super-coarse grit (bur with a grit size of 150 µm) (SCG group), fine grit (bur with a grit size of 30 µm) (FG), air-particle abrasion with 27-µm aluminum oxide particles (APA group), and IDS (IDS group). Each group was divided into 5 subgroups according to the scanning system used to digitize the tooth preparation: laboratory scanner (control subgroup) (T710; Medit), Trios 4 (Trios subgroup), CS 3800 (CS subgroup), i700 wireless (i700 subgroup), and iTero Element 5D Plus (iTero subgroup) (n=20). For each subgroup, the control file was aligned with each experimental scan using the best-fit algorithm and an engineering program (Geomagic Control X). The discrepancy between the control and experimental files of each subgroup was computed by measuring the root mean square (RMS) error. Two-way ANOVA and Tukey tests were used to analyze the data (α=.05). RESULTS: Tooth preparation finishing procedures (P<.001) and the IOS assessed (P<.001) were significant predictors of the trueness and precision values obtained. The highest trueness and precision values were measured in the APA group, while the IDS group had the lowest trueness and precision. Additionally, the i700 subgroup obtained the highest trueness and precision values, while the CS and Trios subgroups had the lowest trueness and precision values. CONCLUSIONS: The different tooth preparations finishing procedures tested influenced on the scanning accuracy of the 4 IOSs considered. The air-particle abrasion procedure obtained the best accuracy values. The trueness discrepancies measured among all the subgroups was 19µm and the precision discrepancies measured among all the subgroups was 4.69 µm. CLINICAL SIGNIFICANCE: The tooth preparation finishing procedure used can reduce the intraoral scanning accuracy of any of the intraoral scanners tested. The air-particle abrasion finishing procedure might be recommended for maximizing the scanning accuracy of the IOSs tested.

A novel chairside technique to assess the interocclusal clearance and abutment axial walls during tooth preparation.

The importance of a judicious and unerring abutment tooth preparation in the field of prosthodontics has always been paramount. It is not uncommon for many clinicians to face challenges during laboratory fabrication of fixed prostheses, caused due to inappropriate occlusal clearance and over axial wall taper of the abutment tooth. With evolving technologies and methods, the modus operandi for attaining such tooth preparation is varying; however, every technique has its own shortcomings. The technique mentioned in the article is cost-effective as it uses modified Heister mouth gag forceps to achieve the desired objective of evaluating the prepared abutment morphology three-dimensionally with minimum chairside time.

[Prediction, analysis and application of learning curve of tooth preparation for all ceramic crowns of maxillary central incisors].

OBJECTIVE: To predict the learning curve of tooth preparation for all ceramic crowns of maxillary central incisors on phantom head simulators for graduate students participating in standardized dental resident training based on the modified Wright learning curve model, then to analyze and applicate the learning curve. METHODS: Twelve graduate students participating in standardized dental resident training were selected to prepare the resin maxillary central incisors on phantom head simulators for all ceramic crowns 4 times. The results of preparation were evaluated by 3 prosthetic experts with at least 10 years' experience focusing on the reduction, contour, taper, shoulder, finish line, margin placement, adjacent tooth injury, and preparation time for tooth preparation. The learning rate of tooth preparation was calculated by scores of tooth preparation of 4 times. The learning curve of tooth preparation was predicted based on the modified Wright learning curve model. According to the criteria of standardized training skill examinations for dental residents in Beijing, 80 was taken as the qualified standard score. The minimum training times for tooth preparation to satisfy the qualified standard score (80) was calculated, to analyze the characteristics of learning curve and evaluate the effectiveness of tooth preparation. RESULTS: The scores of 4 tooth preparation were 64.03±7.80, 71.40±6.13, 74.33±5.96, and 75.98±4.52, respectively. The learning rate was (106±4)%, which showed the learning curve an upward trend. There were no significant differences between the qualified standard score and the predicted scores of tooth preparation from the 5th preparation to the 13th preparation (P > 0.05). The predicted score of the 14th preparation was higher than the qualified standard score (P < 0.05). CONCLUSION: The trend of the learning curve of tooth preparation for all ceramic crowns of maxillary central incisors on phantom head simulators for graduate students participating in standardized dental resident training is upward, which predicts the minimum training times higher than the qualified standard score is 14 times.

Computer-aided design and 3-dimensional artificial/convolutional neural network for digital partial dental crown synthesis and validation.

The current multiphase, invitro study developed and validated a 3-dimensional convolutional neural network (3D-CNN) to generate partial dental crowns (PDC) for use in restorative dentistry. The effectiveness of desktop laser and intraoral scanners in generating data for the purpose of 3D-CNN was first evaluated (phase 1). There were no significant differences in surface area [t-stat(df) = - 0.01 (10), mean difference = - 0.058, P > 0.99] and volume [t-stat(df) = 0.357(10)]. However, the intraoral scans were chosen for phase 2 as they produced a greater level of volumetric details (343.83 ± 43.52 mm3) compared to desktop laser scanning (322.70 ± 40.15 mm3). In phase 2, 120 tooth preparations were digitally synthesized from intraoral scans, and two clinicians designed the respective PDCs using computer-aided design (CAD) workflows on a personal computer setup. Statistical comparison by 3-factor ANOVA demonstrated significant differences in surface area (P < 0.001), volume (P < 0.001), and spatial overlap (P < 0.001), and therefore only the most accurate PDCs (n = 30) were picked to train the neural network (Phase 3). The current 3D-CNN produced a validation accuracy of 60%, validation loss of 0.68-0.87, sensitivity of 1.00, precision of 0.50-0.83, and serves as a proof-of-concept that 3D-CNN can predict and generate PDC prostheses in CAD for restorative dentistry.