Backbone-Photodegradable Polymers by Incorporating Acylsilane Monomers via Ring-Opening Metathesis Polymerization.

Materials capable of degradation upon exposure to light hold promise in a diverse range of applications including biomedical devices and smart coatings. Despite the rapid access to macromolecules with diverse compositions and architectures enabled by ring-opening metathesis polymerization (ROMP), a general strategy to introduce facile photodegradability into these polymers is lacking. Here, we report copolymers synthesized via ROMP that can be degraded by cleaving the backbone in both solution and solid states under irradiation with a 52 W, 390 nm Kessil LED to generate heterotelechelic low-molecular-weight fragments. To the best of our knowledge, this work represents the first instance of the incorporation of acylsilanes into a polymer backbone. Mechanistic investigation of the degradation process supports the intermediacy of an α-siloxy carbene, formed via a 1,2-photo Brook rearrangement, which undergoes insertion into water followed by cleavage of the resulting hemiacetal.

Bifunctional Smart Hydrogel Dressing with Strain Sensitivity and NIR-Responsive Performance.

Smart response hydrogel has a broad application prospect in human health real-time monitoring due to its responses to a variety of stimuli. In this study, we developed a novel smart hydrogel dressing based on conductive MXene nanosheets and a temperature-sensitive PNIPAm polymer. γ-Methacryloxypropyltrimethoxysilane (KH570) was selected to functionalize the surface of MXene further to improve the interface compatibility between MXene and PNIPAm. Our prepared K-M/PNIPAm hydrogel was found to have a strain-sensitive property, as well as a respond to NIR phase change and volume change. When applied as a strain flexible sensor, this K-M/PNIPAm hydrogel exhibited a high strain sensitivity with a gauge factor (GF) of 4.491, a broad working strain range of ≈250%, a fast response of ∼160 ms, and good cycle stability (i.e., 3000 s at 20% strain). Besides, this K-M/PNIPAm hydrogel can be used as an efficient NIR light-controlled drug release carrier to achieve on-demand drug release. This work paved the way for the application of smart response hydrogel in human health real-time monitoring and NIR-controlled drug release functions.

Bio-inspired photonic crystals for naked eye quantification of nucleic acids.

Herein, a chip imitating the desert beetle shell was presented for naked eye nucleic acid quantification. The hydrophobic photonic crystal substrate treated by ultraviolet local irradiation could effectively disperse the sample into hundreds of droplets for digital loop-mediated isothermal amplification (dLAMP). Pyrophosphate (PPI), a by-product of the LAMP reaction, combined with magnesium ions to form a poorly soluble precipitate. It could be fixed on a silica substrate due to complexation, resulting in the disappearance of the structural color of the photonic crystals. The number of points without structural color contains the information of the copy number of nucleic acids in the sample. This chip could achieve the naked eye quantitative detection of Salmonella DNA without fluorescence or other chromogenic reagents. Thus, the chip designed in this study can help the development of digital nucleic acid detection under limited resource settings (LRS) and can be suitable for POCT (point of care test) standards.

Gamma-Irradiation Induced Functionalization of Graphene Oxide with Organosilanes.

Gamma-ray radiation was used as a clean and easy method for turning the physicochemical properties of graphene oxide (GO) in this study. Silane functionalized-GO were synthesized by chemically grafting 3-aminopropyltriethoxysilane (APTES) and 3-glycidyloxypropyltrimethoxysilane (GPTES) onto GO surface using gamma-ray irradiation. This established non-contact process is used to create a reductive medium which is deemed simpler, purer and less harmful compared conventional chemical reduction. The resulting functionalized-GO were characterized by Fourier transform infrared spectroscopy (FT-IR), X-ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM), thermogravimetric analysis (TGA), and Raman spectroscopy. The chemical interaction of silane with the GO surface was confirmed by FT-IR. X-ray diffraction reveals the change in the crystalline phases was due to surface functionalization. Surface defects of the GO due to the introduction of silane mioties was revealed by Raman spectroscopy. Thermogravimetric analysis of the functionalized-GO exhibits a multiple peaks in the temperature range of 200-650 °C which corresponds to the degradation of chemically grafted silane on the GO surface.

Use of a DNA film on a self-assembled monolayer for investigating the physical process of DNA damage induced by core electron ionization.

PURPOSE: A novel two-layer sample composed of a deoxyribonucleic acid (DNA) film and self-assembled monolayer (SAM) was prepared on an inorganic surface to mimic the processes in which DNA is damaged by soft X-ray irradiation. MATERIALS AND METHODS: A mercaptopropyltrimethoxysilane (MPTS) SAM was formed on a sapphire surface, then oligonucleotide (OGN) molecules were adsorbed on the MPTS-SAM. The thicknesses and chemical states of the layers were determined by X-ray photoelectron spectroscopy (XPS) and near-edge X-ray fine structure (NEXAFS) around the phosphorus (P) and sulfur (S) K-edges. To induce the damage to the OGN molecules, the sample was irradiated with synchrotron soft X-rays. The chemical state of the OGN molecules before and after irradiation was examined by NEXAFS around the nitrogen (N) K-edge region. RESULTS: The thickness of the MPTS-OGN layer was approximately 7.7 nm. The S atom of the OGN molecules was located at the bottom of the OGN layer. The peak shape of the N K-edge NEXAFS spectra of the MPTS-OGN layers clearly changed following irradiation. CONCLUSIONS: The MPTS-OGN layer formed on the sapphire surface. The chemical states and the structure of the interface were elucidated using synchrotron soft X-rays. The OGN molecules adsorbed on the MPTS films decomposed upon exposure to soft X-ray irradiation.

Effect of the addition of silanated silica on the mechanical properties of microwave heat-cured acrylic resin.

OBJECTIVES: The purpose of this study was to evaluate the flexural strength and Vickers hardness of a microwave energy heat-cured acrylic resin by adding different concentrations of silane surface-treated nanoparticle silica. METHODS: Acrylic resin specimens with dimensions of 65 × 10 × 2.5 mm were formed and divided into five experimental groups (n = 10) according to the silica concentration added to the acrylic resin mass (weight %) prior to polymerisation : G1, without silica; G2, 0.1% silica; G3, 0.5% silica; G4, 1.0% silica; and G5, 5.0% silica. The specimens were submitted to a three-point flexural strength test and to the Vickers hardness test (HVN). The data obtained were statistically analysed by anova and the Tukey test (α = 0.05). RESULTS: Regarding flexural strength, G5 differed from the other experimental groups (G1, G2, G3 and G4) presenting the lowest mean, while G4 presented a significantly higher mean, with the exception of group G3. Regarding Vickers hardness, a decrease in values was observed, in which G1 presented the highest hardness compared with the other experimental groups. CONCLUSION: Incorporating surface-treated silica resulted in direct benefits in the flexural strength of the acrylic resin activated by microwave energy; however, similar results were not achieved for hardness.

The effects of primer precuring on the shear bond strength between gold alloy surfaces and metal brackets.

The objective of this study was to investigate the effects of precuring of primer coated on bracket bases on the strength of bonds between metal brackets and gold alloy. Square type III gold alloy plates were sandblasted with 30 µm silicon dioxide. After silica coating, excessive particles were removed gently with air. Silane was then applied, and maxillary central incisor metal brackets were bonded to each conditioned alloy surface with Transbond XT. Half of the specimens were precured at the bracket base after primer coating and the other half was not precured before bonding to the alloy surface. After bracket positioning, samples were cured using a light emitting diode (LED) for 40 seconds. Shear bond strengths were tested and adhesive remnant index (ARI) was evaluated after 1 hour and 24 hours. The primer precuring and 24 hours group exhibited highest bond strength (12.53 MPa) and the no precuring and 1 hour group showed lowest bond strength (5.58 MPa). Precured groups showed lower ARI scores. Due to the shallow curing depth of LED light and inhibition of transillumination at the metal surface, primer precuring at the bracket base is required for secure bracket bonding on gold alloy surfaces using LED curing units.

Decatungstate (W10O32(4-))/silane: a new and promising radical source under soft light irradiation.

The use of decatungstate (W10O32(4-)) in combination with silanes to generate silyl radicals under green fluorescence bulb irradiation as well as sunlight exposure is described. The mechanisms are investigated by ESR and laser flash photolysis experiments. The high potential of this reaction is evidenced here when using a decatungstate/silane/diphenyl iodonium salt combination as an initiating system for the ring opening photopolymerization of epoxides.

Surface integrity of solvent-challenged ormocer-matrix composite.

OBJECTIVE: To investigate the surface integrity of solvent-challenged ormocer-matrix composites, photoactivated by different light exposure modes, through surface-hardness measurements at different periods of time; and to compare such behavior with dimethacrylate-based materials. METHODS: One hundred percent ormocer-based matrix (experimental ormocer (ORM)), a commercial mixed dimethacrylate-ormocer-based matrix (Admira (ADR)) and two commercial dimethacrylate-based matrix composites (experimental controls, (Grandio (GRD) and Premise (PRE)) were evaluated. Disk specimens (4 mm × 2 mm) were prepared from each material and light-activated using either a standard (S) or soft-start (SS) light exposure protocol with an LED-curing unit. Top, irradiated surface Knoop hardness (KHN) was measured within the following experimental groups (n=5): Group 1: immediately after exposure; Group 2: after dry and dark storage, Group 3: after storage in distilled water, and Group 4: immersion in absolute ethanol. Hardness of Groups 2-4 were measured after 7 days storage. Immediate hardness values were submitted to Student's t-tests separately for each material. Hardness values after treatments were submitted to two-way ANOVA and Tukey's post hoc test to compare values among different storage media and light exposure mode protocols. Comparisons among materials were described using percentage of hardness change. Statistical testing was performed at a pre-set alpha of 0.05. RESULTS: Immediate hardness values were not affected by the light exposure mode, regardless of the material. In general, exposure mode did not significantly affect hardness after 7 days storage, regardless of storage media or material. After 7 days dry storage, hardness values increased for all materials relative to immediate testing, and decreased after water and ethanol storage, with ethanol showing the greatest effect. The experimental ormocer-based material had the lowest percentage hardness change and thus proved more resistant to solvent degradation than the other materials, regardless of the light exposure method. SIGNIFICANCE: Irradiated surface hardness values and surface integrity were unaffected by light exposure mode, regardless of the material tested. The experimental ormocer-based material presented the least change in hardness as a result of solvent challenge than any of the commercial products: ormocer or conventional resin-based, and thus showed better surface integrity.

Monomer elution from nanohybrid and ormocer-based composites cured with different light sources.

OBJECTIVES: To study monomer elution from four resin-based composites (RBCs) cured with different light sources. METHODS: Twenty-eight premolars were randomly allocated to four groups. Standardized cavities were prepared and restored with a nanohybrid (Filtek Supreme XT or Tetric EvoCeram), an ormocer (Admira) or a microhybrid RBC (Filtek Z250) which served as control. Buccal restorations were cured with a halogen and oral restorations with an LED light-curing unit. Elution of diurethane dimethacrylate (UDMA), Bisphenol A diglycidylether methacrylate (BisGMA), triethylene glycol dimethacrylate (TEGDMA) and 2-hydroxyethyl methacrylate (HEMA) was analyzed using high-performance liquid chromatography (HPLC) 1h to 28 days post-immersion in 75% ethanol. Data were analyzed using multivariate and repeated measures analysis of variance (α = 0.05). RESULTS: The greatest elution of UDMA and BisGMA occurred from Tetric EvoCeram and the least from Filtek Z250 (p < 0.05). LED and halogen light-curing units gave similar results for all RBCs (p > 0.05) except Tetric EvoCeram which showed greater elution for the LED unit (p < 0.05). TEGDMA was below the limit of quantification. HEMA eluted in similar concentrations from Filtek Supreme and Tetric EvoCeram (p > 0.05). SIGNIFICANCE: The two nanohybrid RBCs eluted more cross-linking monomers than the ormocer and the control microhybrid RBC. Continuous elution over 28 days indicates that RBCs act as a chronic source of monomers in clinical conditions. Light source may affect monomer elution since differences were found for one out of four RBCs. Mathematical models for elution kinetics of UDMA and BisGMA indicated two elution mechanisms.

Carbon dioxide laser application enhances the effect of silane primer on the shear bond strength between porcelain and composite resin.

The purpose of this study was to evaluate the effect of carbon dioxide laser irradiation on the performance of silane coupling agent as an adhesion promoter. The carbon dioxide laser used in this study was Opelaser 03S II, which irradiated the silane coupling agent applied on the adhesive surface of porcelain. Before and after thermal cycling, shear bond strength was measured using a universal testing machine. Without primer treatment, most of the specimens failed adhesively before reaching the end of the thermal cycling period. For the specimens irradiated with carbon dioxide laser after primer treatment, their shear bond strengths before and after thermal cycling were higher than those treated with primer only -with a significantly pronounced difference between these two groups especially after thermal cycling. Therefore, a combined surface treatment which involved silane application followed by laser treatment was feasible and efficacious for chairside porcelain repair.

Acceleration of alkenyltrimethylsilane fluorination under mild conditions using ultrasound.

Alkenyltrimethylsilanes are selectively fluorodesilated to alkenyl fluoride very readily by reaction with 1-chloromethyl-4-fluoro-1,4-diazoniabicyclo[2,2,2]octane bis-tetrafluoroborate (Selectfluor) and N-fluorobenzensulfonimids at room temperature under ultrasound. In the presence of ultrasound irradiation in the case of one of the reactions, the yield was 85% after 25 min, but using the previously established thermal method the yield was only 32% after 20 h.

Selective protein patterning based on the micro-structured organosilane self-assembled monolayer by vacuum ultraviolet light lithography.

We have succeeded to immobilize fluorescent proteins selectively using a micro-structured organosilane self-assembled monolayer as a template. An organosilane layer with amino terminal group was formed on a thermally oxidized Si wafer by liquid-phase method and then was pattern-etched by vacuum ultraviolet light (VUV). The second organosilane layer with thiol terminal group was deposited on the etched area by chemical vapor surface modification method (CVSM). These micro-structured organosilane layer containing two reactive terminal groups were chemically modified using bi-functional linkers. Two kinds of fluorescent protein, Enhanced Cyan Fluorescent Protein (ECFP) and R-phycoerythrin were selectively immobilized on the chemically modified surface.

Photoactivation of alkyl C-H and silanization: a simple and general route to prepare high-density primary amines on inert polymer surfaces for protein immobilization.

Surface modification through implanting functional groups has been demonstrated to be extremely important to biomedical applications. The usage of organic polymer phase is often required to achieve satisfactory results. However, organic surfaces usually have poor chemical reactivity toward other reactants and target biomolecules because these surfaces usually only consist of simple alkyl (C-H) and/or alkyl ether (ROR') structures. For the first time, we here report the potential to perform silanization techniques on alkyl polymer surface, which provide a simple, fast, inexpensive, and general method to decorate versatile functional groups at the molecular level. As an example, high-density primary amines could be obtained on a model polymer, polypropylene substrate, through the reaction between amine-capped silane, 3-aminopropyltriethoxysilane (APTES) and hydroxylated polypropylene surface. A model protein, immunoglobulin (IgG), could be effectively immobilized on the surface after transforming amines to aldehydes by the aldehyde-amine condensation reaction between glutaraldehyde (GA) and amines. The routes we report here could directly make use of the benefits from well-developed silane chemistry, and hereby are capable of grafting any functionalities on inert alkyl surfaces via changing the terminal groups in silanes, which should instantly stimulate the development of many realms such as microarrays, immunoassays, biosensors, filtrations, and microseparation.

Effect of UV irradiation on the shear bond strength of titanium with segmented polyurethane through gamma-mercapto propyl trimethoxysilane.

The objective of this study was to investigate the effect of UV irradiation on shear bond strength between a titanium (Ti) and a segmented polyurethane (SPU) composite through gamma-mercapto propyl trimethoxysilane (gamma-MPS). To this end, the shear bond strength of Ti/SPU interface of Ti-SPU composite under varying conditions of ultraviolet ray (UV) irradiation was evaluated by a shear bond test. The glass transition temperatures of SPU with and without UV irradiation were also determined using differential scanning calorimetry. It was found that the shear bond strength of Ti/SPU interface increased with UV irradiation. However, excessive UV irradiation decreased the shear bond strength of Ti/SPU interface. Glass transition temperature was found to increase during 40-60 seconds of UV irradiation. In terms of durability after immersion in water at 37 degrees C for 30 days, shear bond strength was found to improve with UV irradiation. In conclusion, UV irradiation to a Ti-SPU composite was clearly one of the means to improve the shear bond strength of Ti/SPU interface.

Mechanistic analysis of the photocycloaddition of silyl-tethered alkenes.

The photochemistry of substituted cinnamyloxy silanes has been examined in both cyclohexane and acetonitrile solvents. Alkene isomerization occurs in addition to cycloaddition. Fluorescence quantum yields and excited singlet state lifetimes have been determined for each compound. We have used the information in order to better understand the regio- and stereoselectivity of photocycloaddition between silyl-tethered cinnamyl groups. This study allows us to conclude that the 2 + 2 photocycloaddition between alkenes is not a Woodward-Hoffmann orbital symmetry controlled event. The most consistent explanation for the excellent regio- and stereoselectivity is that the photocycloaddition is conformationally controlled.

Visible light-induced photopolymerization of an in situ macroporous sol-gel monolith.

A one-step, in situ, photopolymerization of a mixture of methacryloxypropyltrimethoxysilane in the presence of an acid catalyst, water, and toluene is accomplished in a 75 microm id polyimide-coated capillary using visible light (460 nm) for a 15 min irradiation time. The mixture is a two-component photosystem comprising Irgacure 784 photosensitizer and diphenyliodonium chloride photoinitiator. The visible photopolymerized sol-gel (vis-PSG) column shows RP chromatographic behavior. The analytical potential of these columns is demonstrated with the isocratic separation of small, neutral alkyl phenyl ketones. Operational parameters, such as mobile phase composition, field strength, and column temperature were varied to assess how they affect the separation performance of the monolith.

Three-dimensional cell growth on structures fabricated from ORMOCER by two-photon polymerization technique.

Two-photon polymerization technique was applied to generate three-dimensional (3D) scaffold-like structures using the photosensitive organic-inorganic hybrid polymer ORMOCER. The structures were studied with respect to potential applications as scaffold for tissue engineering. Cell counting and comet assay, respectively, demonstrated that doubling time and DNA strand breaks of CHO cells, GFSHR-17 granulosa cells, GM-7373 endothelial cells, and SH-SY5Y neuroblastoma cells were not affected by ORMOCER. ORMOCER related alteration of formation of tissue specific cell-to-cell adhesions like gap junctions was ruled out by double whole-cell patch-clamp technique. Additionally, growth of cells on the vertical surfaces of 3D structures composed of ORMOCER is shown.

Recyclable hydrophilic-hydrophobic micropatterns on glass for microarray applications.

A novel method for fabricating recyclable hydrophilic-hydrophobic micropatterns on glass chips is presented. TiOx patterns (100-2000 microm) were sputtered on glass chips via a through-hole mask. The patterned chips were then vapor-coated with fluoroalkylsilane, for example, (heptadecafluoro-1,1,2,2-tetrahydrodecyl)triethoxysilane (FTES) to form a hydrophobic coating layer. The fluoroalkyl chain of FTES film on TiOx patterns was photocleaved under UV irradiation, exposing the fresh hydrophilic TiOx patterns. The resulting chip could be used multiple times by repeating the coating and photocleaving processes with negligible deterioration of the hydrophobic FTES film coated on glass. If desired, bare glass patterns could also be generated by removing the TiOx patterns with KOH. The patterned glass chips have been successfully used for microarray fabrication.

Photoinduced polymerization for entrapping of octadecylsilane microsphere columns for capillary electrochromatography.

A novel fritless capillary column for capillary electrochromatography (CEC) has been developed. The ODS microspheres were packed into a capillary and were then immobilized within an organic polymer prepared in situ through a photopolymerization process. The entrapment conditions were investigated to minimize the effect of the polymer matrix on the chromatographic properties of the packing material. The organic polymer matrix in the microsphere-packed column functions to link microspheres at specific sphere-sphere and sphere-capillary contact points. CEC separations of a PAH test mixture using entrapped columns with different UV illumination times were compared in terms of retention factor and separation efficiency. The optimized entrapped column demonstrated better chromatographic performance than similarly packed columns with conventional inlet and outlet frits. The electrochromatographic separations of hormones and peptides were also demonstrated on entrapped ODS columns.