The role of plant uptake in total phosphorous and total nitrogen removal in vegetated bioretention cells using vetiver and cattail.

Bioretention cells have emerged as a prominent strategy for mitigating pollutant loads within urban stormwater runoff. This study delves into the role of plant uptake in the simultaneous removal of nitrogen and phosphorus compounds within these systems. Three bioretention cells-CP, P1, and P2-were constructed using local soil, C33 sand, and gravel. CP served as the unvegetated control, while P1 and P2 were vegetated with vetiver and cattail, respectively. The removal efficiencies of NO3⁻-N, NH3⁻-N, NO2⁻-N, TN, TP, and COD from rainwater were evaluated under saturated and unsaturated conditions. The unvegetated control reactor (CP) achieved TN and TP removal rates of 40.44% and 82.52%, respectively. Reactor P1 (vetiver) demonstrated TN and TP removal rates of 62.92% and 97.19%, respectively. Reactor P2 (cattail) showed TN and TP removal rates of 49.71% and 87.78%, respectively. With the introduction of a saturation zone, TN removal efficiencies increased to 51.69%, 89.22%, and 79.91% for CP, P1, and P2, respectively. However, TP removal efficiencies decreased to 74.81%, 95.04%, and 84.58% for CP, P1, and P2, respectively. Plant tissue uptake tests indicated that vetiver could retain 5 times more TN and twice as much TP compared to cattail. This enhanced performance is attributed to vetiver's high photosynthetic potential as a C4 plant, resilience to varying environmental and nutrient conditions, extensive root network, secretion of oil sesquiterpenes from its root cortex, and the presence of arbuscular mycorrhizal fungi, which secrete glomalin, a substance that promotes water retention and nutrient uptake. Findings from this study indicate that the efficacy of traditional bioretention cells can be augmented through the strategic selection and integration of locally adapted plant species, coupled with the incorporation of saturation zones, to enhance pollutant removal capabilities and resilience to drought conditions.

Mechanistic investigation of azo dye removal from carbon-deficient dyeing wastewater using horizontal-vertical constructed wetlands.

Azo dye degradation can be achieved by simulating a series of anaerobic and aerobic conditions within the constructed wetland (CW) system. The current investigation evaluated the effectiveness of a baffled horizontal-vertical CW system, planted with Typha angustifolia, simulating anaerobic-aerobic conditions to treat carbon-deficient synthetic dyeing wastewater containing 100 mg/L Reactive Yellow 145 (RY145) azo dye. In the absence of an available carbon source in dyeing wastewater, an optimum quantity of sodium acetate was supplemented as the substrate for microbial degradation of RY145. Influent dyeing wastewater characteristics were 5555 ADMI colour, 461 mg/L chemical oxygen demand (COD) and 39 mg/L total nitrogen (TN). During the operation period, the CW system achieved 97% colour, 87% COD, 95% ammonium nitrogen (NH4+-N) and 71% TN removals at 4 d hydraulic retention time (HRT). Favourable environmental conditions, such as low redox conditions and substrate availability in horizontal CW, contributed to a significant reduction in colour (96%). Most TN reduction (67%) happened in horizontal CW by denitrification and plant assimilation. The metagenomic study revealed that Proteobacteria, Bacteroidetes, Chloroflexi and Firmicutes were responsible for pollutant degradation within horizontal CW. The UV-visible spectra and high-resolution liquid chromatograph mass spectrometer (HR-LCMS) analysis confirmed that dye degradation intermediates generated from the breakage of azo bonds were eliminated in vertical CW with high redox conditions. The results of the phytotoxicity and fish toxicity experiments demonstrated a substantial toxicity reduction in the CW system-treated effluent.

Wetland plant species and biochar amendments lead to variable salinity reduction in roadway-associated soils.

Salinization is an emerging threat in freshwater wetlands, with few techniques available to mitigate anthropogenic inputs such as road salts. Phytoremediation and biochar addition have each been proposed to remediate salt-affected soils generally, but interactive effects in wetland environments to improve soil conditions adjacent to roadways are not well understood. We conducted an 88-day fully factorial greenhouse experiment to quantify the effects of three plant treatments (unvegetated, Typha × glauca and Phragmites australis) and three biochar rates (0.0, 2.5, 5.0 % wt/wt) on the soil and leachate of a simulated wetland system. Both plant species significantly reduced soil Cl- content relative to unvegetated controls, while Typha also significantly reduced Cl- content of leachate and soil Na+. The difference in effects was likely due to different salt tolerance strategies: the salt-accumulating Typha contained a significantly higher volume of Na+, Cl-, and water in its tissue than Phragmites, whose greater K+:Na+ ratio and similar soil Na+ to controls indicated a salt exclusion strategy. Biochar did not influence the growth of either species but moderately increased tissue Na+ concentration in Typha. Furthermore, biochar's effects on soil and leachate salt levels varied by application rate with the medium rate moderately increasing soil Na+ and Cl- and leachate Cl-, while the highest application did not differ from controls across all metrics. Our results suggest that phytoremediation can be optimized with salt-accumulating species, whose mechanisms of salt tolerance involve the accumulation of salt ions from the surrounding environment. The consistent flooding in our study may have inhibited the influence of biochar. We recommend future studies parse the effects of water levels and redox potential on biochar's ability to influence wetland salinity. Data repository: doi.org/10.17605/OSF.IO/9QFZ7.

Removal of nutrients from aquaculture wastewater using cattail (Typha spp.) constructed wetlands.

The aquaculture industry is among the fastest growing food production sectors in the world. Land-based aquaculture systems continue to increase in popularity as they offer the benefits of controlling diseases, managing water quality, and minimizing threats to wild populations of fish. However, these systems discharge wastewater high in N and P. The ability of cattail (Typha spp.) constructed wetlands (CWs) to remove N and P from aquaculture wastewater (AWW) was examined here. Cattail CWs were established in mesocosms and had a gradient of AWW applied weekly for a total of 5 weeks. Total N and P loadings ranged from 13.7 to 209.2 mg m-2 and 3.01 to 45.97 mg m-2 over 28 days, respectively. Additions of AWW did not cause elevations in total dissolved N, total ammonia N, or nitrite N in CW water; however, concentrations of nitrate N and P in CW water were related to nutrient loading conditions. Elevations in P persisted for 3-4 weeks among high nutrient loading treatments, providing an opportunity for eutrophic conditions to develop in CW systems. However, after 33 days of treatment, >95% total P concentration reduction was achieved in all mesocosms with final concentrations <0.05 mg L-1, equivalent to reference conditions. High-loading treatments achieved greater P load reduction (856.8-955.0 mg m-2 year-1) than low-loading and reference treatments (591.7-792.7 mg m-2 year-1). This study demonstrates the effectiveness of cattail CWs to remove nutrients during AWW treatment and highlights the potential for end-of-season use in northern climates, providing insights regarding the operational timeline of such systems.

Phytoremediation of metals in oil sands process affected water by native wetland species.

Process affected water and other industrial wastewaters are a major environmental concern. During oil sands mining, large amounts of oil sands process affected water (OSPW) are generated and stored in ponds until reclaimed and ready for surface water discharge. While much research has focused on organics in process waters, trace metals at high concentrations may also pose environmental risks. Phytoremediation is a cost effective and sustainable approach that employs plants to extract and reduce contaminants in water. The research was undertaken in mesocosm scale constructed wetlands with plants exposed to OSPW for 60 days. The objective was to screen seven native emergent wetland species for their ability to tolerate high metal concentrations (arsenic, cadmium, copper, chromium, copper, nickel, selenium, zinc), and then to evaluate the best performing species for OSPW phytoremediation. All native plant species, except Glyceria grandis, tolerated and grew in OSPW. Carex aquatilis (water sedge), Juncus balticus (baltic rush), and Typha latifolia (cattail) had highest survival and growth, and had high metal removal efficiencies for arsenic (81-87 %), chromium (78-86 %), and cadmium (74-84 %), relative to other metals; and greater than 91 % of the dissolved portions were removed. The native plant species were efficient accumulators of all metals, as demonstrated by high root and shoot bioaccumulation factors; root accumulation was greater than shoot accumulation. Translocation factor values were greater than one for Juncus balticus (chromium, zinc) and Carex aquatilis (cadmium, chromium, cobalt, nickel). The results demonstrate the potential suitability of these species for phytoremediation of a number of metals of concern and could provide an effective and environmentally sound remediation approach for wastewaters.

The potential application of Czenspinskia transversostriata in biological control.

Phytoseiid predatory mites are one of the most important groups of biocontrol agents, commonly used in biological control. The ability to produce these predatory mites economically, at high density on cheap factitious food sources, is a major contributor to their success. Astigmatid mites are the most widely used factitious food for this purpose. In this study, we investigated the potential application of the leaf-dwelling astigmatid mite Czenspinskia transversostriata (Oudemans) (Acari: Winterschmidtiidae) as a prey mite in biological control. We tested whether C. transversostriata is a suitable food source for the predatory mite Amblyseius swirskii Athias-Henriot (Acari: Phytoseiidae), both in the laboratory and on cucumber plants. Based on a reproduction trial, C. transversostriata proved to be an equally good food source compared to both pollen of Typha angustifolia L. (Poales: Typhaceae) and a frequently used prey mite Carpoglyphus lactis L. (Acari: Carpoglyphidae). In a pre-establishment trial on cucumber plants, populations of A. swirskii reached equally high densities when supplemented with C. transversostriata, compared to C. lactis. Lastly, we show that C. transversostriata is capable of feeding and reproducing on powdery mildew growing on cucumber plants, thereby slowing down the development of the pathogenic fungus. Results derived from this study show that C. transversostriata may have multiple potential applications in biological control programs.

Construction of an ideotype root system architecture of subsurface flow constructed wetland macrophytes by vertical spatial stress: strengthening of rhizosphere effects and determination of appropriate substrate depth.

Strengthening rhizosphere effects to enhance pollutant removal is a hotspot of constructed wetlands (CWs) research in recent years, and improving the root traits and metabolic capacity of macrophytes is crucial for strengthening rhizosphere effects. In the field experiment, two types of subsurface flow (SSF) CWs (CW10 and CW20, with substrate depths of 10 and 20 cm, respectively) under the vertical spatial stress of roots (VSSR) and two types of non-VSSR SSF CWs (CW40 and CW60) were adopted with Typha orientalis as cultivated plants to investigate the variability of root development, metabolism, and pollutant removal at different substrate depths. VSSR induced substantial redundant root development, which significantly increased root-shoot ratio, fine and lateral root biomass, root porosity, and root activity, with lateral and fine root biomass of CW20 reaching 409.17 and 237.42 g/m2, respectively, which were 3.18 and 5.28 times those of CW60. The radical oxygen loss (ROL) and dissolved organic carbon (DOC) levels of CW20 single plant were 1.36 and 4.57 times higher than those of CW60, respectively, and more types of root exudates were determined (e.g., aldehydes, ketones and amides). More aerobic heterotrophs (e.g., Massilia, Planomicrobium), nitrification bacteria (e.g., Ellin6067, Nitrospira), aerobic denitrification bacteria (e.g., Bacillu, Chryseobacterium, Pseudomonas) and denitrification phosphorus accumulating organisms (e.g., Flavobacterium) were enriched in the rhizosphere of CW20. This changed the main transformation pathways of pollutants and enhanced the removal of pollutants, with the COD, TN and TP average removal rates of CW20 increasing by 9.99%, 13.28% and 8.92%, respectively, compared with CW60. The ideotype root system architecture CW (RSACW; CW20) constructed in this study, which consists of a large number of fine and lateral roots, can stimulate more efficient rhizosphere effects stably and continuously.

Per- and polyfluoroalkyl substances removal from landfill leachate by a planting unit via interactions between foamed glass and Typha domingensis.

Sustainable removal of per- and polyfluoroalkyl substances (PFAS) from landfill leachate remains a pressing global challenge. To develop an effective PFAS removal technology that utilizes nature-based solutions, we considered a planting unit comprised of a microbial carrier (foamed glass) and Typha domingensis. This study evaluated the possibility of removing PFAS from landfill leachate using a planting unit through a pot experiment. The planting unit effectively removed various short- and long-chain PFAS from the landfill leachate, including perfluorocarboxylic acids (PFCAs [C4-C10]), perfluorosulfonic acids (PFSAs [C4, C6, and C8]), fluorotelomer carboxylic acids (FTCAs [5:3 and 7:3]), and 6:2 fluorotelomer sulfonic acid (FTS), with initial concentrations of 43-9100 ng L-1, achieving a removal efficiency of 53-83% in 21 d. Mass balance analysis indicated that the contribution of accumulation on foamed glass and plant adsorption and uptake played no major role in the removal of PFCAs (C4-C9), PFSAs (C4), and FTCAs (5:3 and 7:3), and that other removal processes played a key role. Although not the most effective removal process, the contribution of accumulation on foamed glass tended to be more notable in the removal of longer-chain PFCAs. In addition, plant adsorption and uptake showed that longer-chain PFCAs were more likely to remain in roots, whereas shorter-chain PFCAs were more likely to be transferred to aboveground plant part. On the other hand, 6:2 FTS removal occurred primarily due to accumulation on foamed glass. These results suggest that differences in the physicochemical properties of PFAS affect removal mechanisms. This study provides valuable insights into development of environmentally friendly technologies capable of removing a variety of short- and long-chain PFAS.

Plastic and terrestrial organic matter degradation by the humic lake microbiome continues throughout the seasons.

Boreal freshwaters go through four seasons, however, studies about the decomposition of terrestrial and plastic compounds often focus only on summer. We compared microbial decomposition of 13C-polyethylene, 13C-polystyrene, and 13C-plant litter (Typha latifolia) by determining the biochemical fate of the substrate carbon and identified the microbial decomposer taxa in humic lake waters in four seasons. For the first time, the annual decomposition rate including separated seasonal variation was calculated for microplastics and plant litter in the freshwater system. Polyethylene decomposition was not detected, whereas polystyrene and plant litter were degraded in all seasons. In winter, decomposition rates of polystyrene and plant litter were fivefold and fourfold slower than in summer, respectively. Carbon from each substrate was mainly respired in all seasons. Plant litter was utilized efficiently by various microbial groups, whereas polystyrene decomposition was limited to Alpha- and Gammaproteobacteria. The decomposition was not restricted only to the growth season, highlighting that the decomposition of both labile organic matter and extremely recalcitrant microplastics continues throughout the seasons.

Analysis of ammonia-nitrogen removal kinetics by stage in pilot scale vertical flow wetlands treating landfill leachate in series.

This study explored the effect stage number and plant type have on ammonia-nitrogen (NH3-N) removal kinetics in a two-stage pilot-scale vertical flow constructed wetland (VFCW) system treating landfill leachate. Half of the VFCW columns were planted with Typha latifolia and the other half Scirpus californicus, and half of the columns were loaded with municipal solid waste landfill leachate (diluted to 1 part leachate to 2 parts total) with the effluent from these columns was collected in two separate barrels. The remaining columns were loaded with the effluent collected from the first columns, creating a two-stage VFCW system with four unique pairs to be tested. The leachate used here experienced no prior pre-treatment, and average influent concentrations of NH3-N for the first- and second-stage VFCWs were 508 and 321 mg L-1, respectively- much higher than many other VFCW treatment systems. Some reduction in chemical oxygen demand was observed, as well as generation of nitrate and nitrite, evidence of nitrification. No apparent correlation between aboveground biomass and removal of NH3-N was observed. Overall removal efficiency of NH3-N through two stages of VFCWs was 53.7% for columns planted with T. latifolia and 58.3% for those planted with S. Californicus. Average NH3-N removal efficiencies for the first stage VFCWs were 32.7% and 34.3%, while those in the second stage were 31.3% and 36.5%; no significant difference was observed between the first and second stage, suggesting that stage number does not have a significant effect on the removal efficiency of NH3-N in the primary treatment of landfill leachate via VFCWs. However, average mass removal rates of NH3-N in the first stage were 166 and 175 mg L-1 d-1; the second stage was significantly lower at 99.4 and 112 mg L-1 d-1, indicating that the first stage removed more pollutants overall.

Contrasting plant-induced changes in heavy metals dynamics: Implications for phytoremediation strategies in estuarine wetlands.

Wetland plants play a crucial role in regulating soil geochemistry, influencing heavy metal (HM) speciation, bioavailability, and uptake, thus impacting phytoremediation potential. We hypothesized that variations in HM biogeochemistry within estuarine soils are controlled by distinct estuarine plant species. We evaluated the soils (pH, redox potential, rhizosphere pH, HM total concentration, and geochemical fractionation), plant parts (shoot and root), and iron plaques of three plants growing in an estuary affected by Fe-rich mine tailings. Though the integration of multiple plant and soil analysis, this work emphasizes the importance of considering geochemical pools of HM for predicting their fate. Apart from the predominance of HM associated with Fe oxides, Typha domingensis accumulated the highest Cr and Ni contents in their shoots (> 100 mg kg-1). In contrast, Hibiscus tiliaceus accumulated more Cu and Pb in their roots (> 50 mg kg-1). The differences in rhizosphere soil conditions and root bioturbation explained the different potentials between the plants by altering the soil dynamics and HM's bioavailability, ultimately affecting their uptake. This study suggests that Eleocharis acutangula is not suitable for phytoextraction or phytostabilization, whereas Typha domingensis shows potential for Cr and Ni phytoextraction. In addition, we first showed Hibiscus tiliaceus as a promising wood species for Cu and Pb phytostabilization.

Evaluation of electrode separators and the external resistance in electrochemically assisted constructed wetlands.

A proton exchange membrane increases the electrical performance of a microbial fuel cell (MFC). New inexpensive materials should be sought, especially in a constructed wetland microbial fuel cell (CW-MFC). Here, in a laboratory-scale system of five CW-MFCs, wet clay, wet earth or mud, and non-woven cloth were used as inexpensive separators with long-term stability. The five CW-MFCs were planted with Typha latifolia, fed with synthetic wastewater, and packed with natural porous material. Graphite felt was used as electrodes and the experimental system had a hydraulic residence time of 3 days, operating under shade and natural conditions of temperature and light. Electrodes were connected to current collectors (copper wire) and to an external resistance, with a change every 20 days, starting in open-circuit and following with 20000, 18000, 15000, 10000, 5600, 1000, 560, and 10 Ω. These laboratory-scale CW-MFCs reduced concentrations of nitrates, ammonium ion, and sulfates without inhibiting electricity production. Microbiological analyses indicated that anaerobic, facultative, aerobic, and denitrifying bacteria may have caused these reductions. The reactor with the live plant and with the wet earth or mud separator achieved the highest production of electricity (22.6 mW/m2), and may be worth further attention.

Resistance of the fiber-derived geotextile from Typha domingensis submitted to field degradation.

Geotextiles made from plant fibers creates a suitable environment for plant growth as part of soil bioengineering techniques. The faster decomposition of plant fiber geotextiles compared to synthetic ones demands the use of composites that enhance their waterproofing and extend their durability in the environment. The objective of this work was to evaluate the resistance of a geotextile made with Thypha domingensis to degradation caused by climatic variables. Tensile strength tests were conducted in the laboratory in order to evaluate the degradation of geotextiles treated with single and double layers of waterproofing resin. Based on Scanning Electron Microscopy (SEM) images, it was verified that applying double layer of waterproofing resin delays the fibers degradation up to 120 days of exposure to the effects of climatic variables other than temperature. The maximum resistance losses due to the geotextile's exposure to degradation were statistically significant for all three treatments: control-without waterproofing resin, with one layer resin, and with two layers resin. Therefore, waterproofing resin, provides a long-term protective solution for geotextiles made from cattail fibers.

Greenhouse gases emissions and carbon budget estimation in horizontal subsurface flow constructed wetlands with different plant species.

Constructed wetlands (CWs) are pivotal for wastewater treatment due to their high efficiency and numerous advantages. The impact of plant species and diversity on greenhouse gas (GHG) emissions from CWs requires a more comprehensive evaluation. Moreover, controversial perspectives persist about whether CWs function as carbon sinks or sources. In this study, horizontal subsurface flow (HSSF) CWs vegetated with Cyperus alternifolius, Typhae latifolia, Acorus calamus, and the mixture of these three species were constructed to evaluate pollutant removal efficiencies and GHG emissions, and estimate carbon budgets. Polyculture CWs can stably remove COD (86.79 %), NH4+-N (97.41 %), NO3--N (98.55 %), and TP (98.48 %). They also mitigated global warming potential (GWP) by suppressing N2O emissions compared with monoculture CWs. The highest abundance of the Pseudogulbenkiania genus, crucial for denitrification, was observed in polyculture CWs, indicating that denitrification dominated in nitrogen removal. While the highest nosZ copy numbers were observed in CWs vegetated with Cyperus alternifolius, suggesting its facilitation of denitrification-related microbes. Selecting Cyperus alternifolius to increase species diversity is proposed for simultaneously maintaining the water purification capacity and reducing GHG emissions. Carbon budget estimations revealed that all four types of HSSF CWs were carbon sinks after six months of operation, with carbon accumulation capacity of 4.90 ± 1.50 (Cyperus alternifolius), 3.31 ± 2.01 (Typhae latifola), 1.78 ± 1.30 (Acorus calamus), and 2.12 ± 0.88 (polyculture) kg C/m2/yr. This study implies that under these operation conditions, CWs function as carbon sinks rather than sources, aligning with carbon peak and neutrality objectives and presenting significant potential for carbon reduction efforts.

A novel strategy for the quality control of carbonized Typhae pollen using colorimeter, liquid chromatography-mass spectrometry, and efficacy evaluation coupled with multivariate statistical analysis.

In this study, a novel quality control strategy was proposed, aiming to establish a multivariate specification for the processing step by exploring the correlation between colors, chemical components, and hemostatic effects of the carbonized Typhae pollen (CTP) using multivariate statistical analysis. The CTP samples were stir-fried at different durations. Afterward, the colorimeter and LC-MS techniques were applied to characterize the CTP samples, followed by the determination of bleeding time and clotting time using mice to evaluate their hemostatic effect. Then, principal component analysis, hierarchical cluster analysis, and multi-block partial least squares were used for data analysis on colors, chemical components, and their correlation with the hemostatic effect. Consequently, 13 critical quality attributes (CQAs) of CTP were identified via multivariate statistical analysis-L*, a*, b*, 3,4-dihydroxybenzoic acid, 4-hydroxybenzoic acid, 3-hydroxybenzoic acid, quercetin-3-O-glucoside, azelaic acid, kaempferol-3-O-glucoside, quercetin, naringenin, kaempferol, and isorhamnetin. The multivariate specification method involving the 13 CQAs was developed and visualized in the latent variable space of the partial least squares model, indicating that the proposed method was successfully applied to assess the quality of CTP and the degree of carbonization. Most importantly, this study offers a novel insight into the control of processing for carbonized Chinese herbal medicines.

Tolerance to mild shading levels in cattail as related to increased photosynthesis and changes in its leaf area and anatomy.

Shading is an environmental factor that has been little investigated regarding its effects on emergent aquatic plants. Typha domingensis Pers. is an emergent macrophyte that demonstrates some plasticity for self-shading, and as it can shade other species in the same area, the effect of shading on its traits deserves further investigation. The objective of the present study was to evaluate the gas exchange, leaf anatomy, and growth of T. domingensis cultivated under increasing shading intensities. The plants were collected and propagated in a greenhouse, and the clones were subjected to four shading intensities: 0% (unshaded), 35%, 73%, and 83% shading created by black nets. Growth traits, clonal production, photosynthesis, transpiration, and leaf anatomy were evaluated. The 73% and 83% shading promoted the death of all plants, but all plants survived in the 35% and unshaded treatments. Compared with the unshaded treatment, the 35% shading treatment promoted a higher photosynthetic rate and greater transpiration, supporting increased growth and production of clones. The increase in the photosynthetic rate in the 35% shading was related to the increase in leaf area which increased the photosynthesis of the whole plant. The 73% and 83% treatments inhibited the development of photosynthetic parenchyma and stomata in T. domingensis, leading to a drastic reduction in photosynthesis and energy depletion. Therefore, T. domingensis does not tolerate intense shading, but its photosynthetic characteristics and growth are favored by mild shading, a factor that may be of great importance for its competitiveness and invasive behavior.

Optimizing Typha biochar with phosphoric acid modification and ferric chloride impregnation for hexavalent chromium remediation in water and soil.

Considering the persistent and covert nature of heavy metal soil contamination, the sustainable development of ecological environments and food safety is at significant risk. Our study focuses on remediating soils contaminated with chromium (Cr); we introduce an advanced remediation material, iron oxide phosphoric acid-loaded activated biochar (HFBC), synthesized through pyrolysis. This HFBC displays greater microporosity, fewer impurities, and enhanced efficiency for the remediation process. Our research utilized a comprehensive set of analytical techniques, including Scanning Electron Microscopy (SEM), Fourier Transform Infrared Spectroscopy (FTIR), and X-ray Photoelectron Spectroscopy (XPS), alongside adsorption studies to elucidate the Cr removal mechanism. The effectiveness of HFBC in remediation was influenced by several factors: the pH level, dosage of HFBC, the initial concentration of Cr, and the ambient temperature. Our results indicated an optimal chromium (VI) adsorption capacity of 55.5 mg/g by HFBC at a pH of 6.0 and a temperature of 25 °C, with the process adhering to the pseudo-second-order kinetic model and the Langmuir adsorption isotherm, thus suggesting spontaneity in the uptake method. Moreover, this mechanism encompasses both adsorption and reduction reactions. Using HFBC in pot experiments with cabbage indicated not only an increase in soil pH and cation exchange capacity (CEC), but also a surge in bacterial community abundance. Significant reductions in bioavailable chromium were also recorded. Interestingly, HFBC addition bolstered the growth of cabbage, while concurrently diminishing chromium accumulation within the plant, particularly notable as the HFBC application rate increased. In summation, the HFBC produced in our study has demonstrated convincing efficacy in removing chromium from aqueous solutions and soil. Moreover, the positive agronomic implications of its use, such as enhanced plant growth and reduced heavy metal uptake by plants, indicate its high potential for operational value in the domain of environmental remediation of heavy metals.

Rare flavanone-diarylheptanoid hybrids from Typha angustifolia shows anti breast cancer activity via activating TGF-ß1/Smad signaling pathway.

Four new flavanone-diarylheptanoid hetero dimers, typhatifolins A-D (1-4), were separated from the pollen of a widely distributed medicinal plant Typha angustifolia. Structures of these rare hybrids were elucidated by detailed interpretation of spectroscopic data, and their absolute configurations were determined on the basis of Mosher's method and ECD analyses. All the four compounds showed moderate to significant cytotoxicities against a panel of tumor cell lines with IC50 values ranging from 0.67 to 12.48 µM. Further in vitro antitumor evaluation for typhatifolin B (TTB, 2) on two breast cancer cells (4T1 and MDA-MB231) revealed that it could remarkably induce cell apoptosis and G0/G1 cycle arrest, as well as block cell migration and invasion. Mechanistically, TTB could exert its antitumor effect via activating the TGF-ß1 (transforming growth factor beta 1) signaling pathway as evidenced by RNA-seq analysis and immunoblotting experiments, which was further corroborated by treating cancer cells with a TGF-ß signaling inhibitor. Lastly, the in vivo anti breast cancer activity was demonstrated by applying the mixture of typhatifolins A-D to a preclinical animal model.

Pollen provisioning attenuates pesticide side-effects on a phytoseiid predator.

BACKGROUND: Biological control with predatory mites is applied against pests in greenhouse crops. Chemical control with the use of selective, reduced-risk pesticides, is an important component of Integrated Pest Management (IPM) programs, that often needs to be combined with biological control. Here, we evaluated the effect of plant pollen when used as supplementary food on the survival, reproduction and predation of the predatory mite Amblydromalus limonicus (Acari: Phytoseiidae) after exposing young larvae and adults to flonicamid, an insecticide of moderate toxicity to phytoseiids. Pollen is an important alternative food for generalist phytoseiids ensuring survival and supporting populations build-up during periods of prey scarcity. Two regimes of cattail (Typha angustifolia L.) pollen differing in application frequency were used. In the first, the total amount of pollen was supplied once, within 30 min after insecticide application, whereas in the second regime, the same amount of pollen was supplied gradually, i.e., every 48 h. RESULTS: Regardless of the frequency of application, pollen provisioning results in a reduction in prey (thrips) consumption relative to the control (no pollen provisioning). Nevertheless, when adult mites were directly exposed to flonicamid residues, pollen provisioning attenuated the reduction in prey consumption as compared to the control. In addition, the gradual (every 48 h) provisioning of pollen to adult predators exposed to flonicamid residues impacted positively the intrinsic rate of population increase (rm) of A. limonicus as compared to when feeding on prey. CONCLUSION: Our results reveal an unexpected role of pollen provisioning in alleviating pesticides side-effects on phytoseiids. © 2024 The Authors. Pest Management Science published by John Wiley & Sons Ltd on behalf of Society of Chemical Industry.

Extraction and characterization of nanocellulose from cattail leaves: Morphological, microstructural and thermal properties.

Hydrogen peroxide combined with acid treatment demonstrates its respective characteristics for the separation of lignocellulosic biomass. Herein, holocellulose was extracted from Cattail leaves (CL) by a two-step treatment with alkali and hydrogen peroxide-acetic acid (HPAA). Then carboxylated nanocellulose was hydrolyzed with a mixed organic/inorganic acid. The chemical composition of the holocellulose and the physicochemical properties of the separated carboxylated nanocellulose were comparable. Carboxyl groups were introduced on the nanocellulose as a result of the esterification process with citric acid (CA), which endows the nanocellulose with high thermal stability (315-318 °C) and good light transmission (>80 %). Furthermore, morphological analyses revealed that nanocellulose had a spider-web-like structure with diameter between 5 and 20 nm.