Rheology of graphene oxide stabilized Pickering emulsions.

Pickering emulgels stabilized by graphene oxide (GO) with didodecyldimethylammonium bromide (DDAB) as an auxiliary surfactant and liquid paraffin as the oil phase have proved to be an excellent 3D printable ink. This paper elucidates the structure of such emulgels by a combination of microscopy before and after intensive shear as well as broadband dielectric spectroscopy and rheology in the linear and nonlinear regime. An increase of the DDAB surfactant and GO-contents leads to a systematic increase of modulus and viscosity, a reduction of the limits of the nonlinear regime and a more complicated variation of the normal forces, with negative normal forces at high shear rate  for low GO-contents and positive normal forces at high GO-contents. The interfacial jamming behavior studied by morphology, rheology and dielectric spectroscopy is explained based on droplet deformation, jamming and recovery phenomena.

Understanding Gel-Powers: Exploring Rheological Marvels of Acrylamide/Sodium Alginate Double-Network Hydrogels.

This study investigates the rheological properties of dual-network hydrogels based on acrylamide and sodium alginate under large deformations. The concentration of calcium ions affects the nonlinear behavior, and all gel samples exhibit strain hardening, shear thickening, and shear densification. The paper focuses on systematic variation of the alginate concentration-which serves as second network building blocks-and the Ca2+-concentration-which shows how strongly they are connected. The precursor solutions show a typical viscoelastic solution behavior depending on alginate content and pH. The gels are highly elastic solids with only relatively small viscoelastic components, i.e., their creep and creep recovery behavior are indicative of the solid state after only a very short time while the linear viscoelastic phase angles are very small. The onset of the nonlinear regime decreases significantly when closing the second network (alginate) upon adding Ca2+, while at the same time the nonlinearity parameters (Q0, I3/I1, S, T, e3/e1, and v3/v1) increase significantly. Further, the tensile properties are significantly improved by closing the alginate network by Ca2+ at intermediate concentrations.

Influence of Cellulose Nanofibers on the Behavior of Pickering Emulsions. Part 1. Microscopy and Startup Flow Test.

The dispersibility of flexible polymer chains present at the emulsion's interface between the dispersed and continuous phase has obvious effects on rheology and dielectric properties of the whole emulsion. Cellulose nanofiber (CNF)-based Pickering emulsions are good systems to research these properties with respect to their microscopic phase structure, dielectric, and rheological properties by using CNF as a water-dispersible Pickering emulsifier, liquid paraffin as an oil phase, and didodecyldimethylammonium bromide (DDAB) as a cationic auxiliary surfactant. The CNF and DDAB contents were systematically varied while the water-to-paraffin oil ratio was kept constant to discern the influence of the Pickering emulsifiers. Polarized optical microscopic images reveal that the droplets tend to shrink at higher CNF content but grow bigger when increasing the DDAB content, which is proved by fluorescence analysis of the CNF dispersibility with varying DDAB content. The dielectric damping exhibits a minimum, whose value decreases with increasing DDAB and CNF content. Increasing the DDAB content promotes the solubilization of CNF in the aqueous phase, which will increase the overall viscosity and yield points. Similarly, a higher CNF content leads to a higher viscosity and yield point, but at high DDAB contents, the viscosity function exhibits an S-shape at intermediate CNF contents. To evaluate the results further, they were compared with CNF dispersions (without oil phase), which showed a surfactant effect slightly on maximum stress but strongly on yield stress τy, indicating that DDAB can promote the formation of a CNF network rather than the viscosity of the whole system. This paper provides information on how a systematical variation of the composition influences morphology and physico-chemical interactions as detected by broadband dielectric spectroscopy and rheological behavior.

Rheological Behavior of Blends of Metallocene Catalyzed Long-Chain Branched Polyethylenes. Part I: Shear Rheological and Thermorheological Behavior.

Long-chain branched metallocene-catalyzed high-density polyethylenes (LCB-mHDPE) were solution blended to obtain blends with varying degrees of branching. A high molecular LCB-mHDPE was mixed with low molecular LCB-mHDPE at varying concentrations. The rheological behavior of those low molecular LCB-mHDPE is similar but their molar mass and molar mass distribution are significantly different. Those blends were characterized rheologically to study the effects of concentration, molar mass distribution, and long-chain branching level of the low molecular LCB-mHDPE. Owing to the ultra-long relaxation times of the high molecular LCB-mHDPE, the blends exhibited a clearly more long-chain branched behavior than the base materials. The thermorheological complexity analysis showed an apparent increase in the activation energies Ea determined from G', G″, and especially δ. Ea (δ), which for LCB-mHDPE is a peak function, turned out to produce even more pronounced peaks than observed for LCB-mPE with narrow molar mass distribution and also LCB-mPE with broader molar mass distribution. Thus, it is possible to estimate the molar mass distribution from the details of the thermorheological complexity.

The selection of a surfactant for freshwater microalgae harvesting and separation by the foam separation method.

Collecting microalgae from water with less energy and cost is significant to gain economic profit from microalgae harvesting and processing. Foam separation has certain advantages including low energy consumption, simple operation and easy maintenance of the equipment. Natural surfactants, compared to traditional surfactants, were used to harvest and separate the freshwater microalgae Desmodesmus brasiliensis by foam separation. Results showed a recovery percentage of 93.6% and an enrichment ratio of 23.1 with the natural surfactant cocamidopropyl betaine (CAPB), suggesting that this low-cost surfactant can be applied to microalgae biomass recovery on a commercial scale using foam separation with no negative effect on the content of microalgae chlorophyll, carotenoid or protein.