RESUMO
Tin (Sn) is a useful anode material for lithium ion batteries (LIBs) because of its high theoretical capacity. We fabricated oil-in-water emulsion-templated tin nanoparticle/carbon black (SnNP/CB) anodes with octane, hexadecane, 1-chlorohexadecane, and 1-bromohexadecane as the oil phases. Emulsion creaming, the oil vapor pressure, and the emulsion droplet size distribution all affect drying and thus the morphology of the dried emulsion. This morphology has a direct impact on the electrochemical performance of the anode. SnNP/CB anodes prepared with hexadecane showed very few cracks and had the highest capacities and capacity retention. The combination of low vapor pressure, creaming, which forced the emulsion droplets into a close-packed arrangement on the surface of the continuous water phase, and the small droplets allowed for gentle evaporation of the liquids during drying. This led to lower differential stresses on the sample and reduced cracking. For octane, the vapor pressure was high, the droplet sizes were large for 1-cholorohexadecane, and there was no creaming for 1-bromohexadecane. All of these factors contributed to cracking of the anode surface during drying and reduced the electrochemical performance. Choosing an oil with balanced properties is important for obtaining the best cell performance for emulsion-templated anodes for LIBs.
RESUMO
A direct comparison of the cathode-electrolyte interface (CEI) generated on high-voltage LiNi0.5Mn1.5O4 cathodes with three different lithium borate electrolyte additives, lithium bis(oxalato)borate (LiBOB), lithium 4-pyridyl trimethyl borate (LPTB), and lithium catechol dimethyl borate (LiCDMB), has been conducted. The lithium borate electrolyte additives have been previously reported to improve the capacity retention and efficiency of graphite/LiNi0.5Mn1.5O4 cells due to the formation of passivating CEI. Linear sweep voltammetry (LSV) suggests that incorporation of the lithium borates into 1.2 M LiPF6 in EC/EMC (3/7) electrolyte results in borate oxidation on the cathode surface at high potential. The reaction of the borates on the cathode surface leads to an increase in impedance as determined by electrochemical impedance spectroscopy (EIS), consistent with the formation of a cathode surface film. Ex-situ surface analysis of the electrode via a combination of SEM, TEM, IR-ATR, XPS, and high energy XPS (HAXPES) suggests that oxidation of all borate additives results in deposition of a passivation layer on the surface of LiNi0.5Mn1.5O4 which inhibits transition metal ion dissolution from the cathode. The passivation layer thickness increases as a function of additive structure LiCDMB > LPTB > LiBOB. The results suggest that the CEI thickness can be controlled by the structure and reactivity of the electrolyte additive.
RESUMO
ABSTRACT: ZnCo2O4 nanocluster particles (NCPs) were prepared through a designed hydrothermal method, with the assistance of a surfactant, sodium dodecyl benzene sulfonate. The crystalline structure and surface morphology of ZnCo2O4 were investigated by XRD, XPS, SEM, TEM, and BET analyses. The results of SEM and TEM suggest a clear nanocluster particle structure of cubic ZnCo2O4 (~100 nm in diameter), which consists of aggregated primary nanoparticles (~10 nm in diameter), is achieved. The electrochemical behavior of synthesized ZnCo2O4 NCPs was investigated by galvanostatic discharge/charge measurements and cyclic voltammetry. The ZnCo2O4 NCPs exhibit a high reversible capacity of 700 mAh g-1 over 100 cycles under a current density of 100 mA g-1 with an excellent coulombic efficiency of 98.9% and a considerable cycling stability. This work demonstrates a facile technique designed to synthesize ZnCo2O4 NCPs which show great potential as anode materials for lithium ion batteries.
