Humidity-tolerant and highly sensitive gas sensor for hydrogen sulfide based on WO3 nanocubes modified with CeO2.

The influence of ambient humidity on the gas-sensing characteristics of metal oxide semiconductors has been one of the greatest obstacles for gas-sensing applications. In this paper, the pure WO3 and CeO2-modified WO3 nanocubes were prepared by a simple hydrothermal method, and their gas-sensing characteristics in dry and humid atmospheres were investigated. The results show that CeO2/WO3 demonstrated excellent gas-sensing properties toward H2S with high sensitivity and high selectivity at 115 °C. Noteworthy, the humidity independence of the CeO2/WO3 increased compared to the WO3. The response retentions over the whole humidity range of the CeO2/WO3-6 and CeO2/WO3-15 sensors were 70.3, and 76%, respectively, which were much higher than the WO3 sensor (17.9%). The gas-sensing mechanism of CeO2-modified WO3 is discussed based on the gas sensitivity properties. The obtained results provide a promising route to enhance the anti-humidity properties of metal oxide semiconductor gas sensors.

A high-performance room-temperature NH3 gas sensor based on WO3/TiO2 nanocrystals decorated with Pt NPs.

In this work, a high-performance room-temperature ammonia (NH3) gas sensor based on Pt-modified WO3-TiO2 nanocrystals was synthesized via a two-step hydrothermal method. The structural properties were characterized by scanning electron microscopy, transmission electron microscopy, X-ray diffraction, and X-ray photoelectron spectroscopy. The 10 at% Pt@WO3-TiO2 nanocrystals present the highest NH3 sensing performance at room temperature. Compared with the nanocrystals without Pt modification, the sensitivity of the Pt@WO3-TiO2 sensor is tenfold higher, with the lowest concentration threshold reaching the 75 ppb level. The response is approximately 92.28 to 50 ppm, and response and recovery times are 23 s and 8 s, respectively. The improved sensing was attributed to a synergetic mechanism involving the space charge layer effect and Pt metal sensitization, enhancing the electron transfer efficiency, oxygen vacancy and specific surface area. This study is expected to guide the development of high-performance room-temperature ammonia sensors for clinical breath testing.

Diagnostic performance of 3.0 T unenhanced Dixon water-fat separation coronary MR angiography in patients with low-to-intermediate risk of coronary artery disease.

PURPOSE: To evaluate the diagnostic performance of 3.0 T unenhanced compressed-sensing sensitivity encoding (CS-SENSE) Dixon water-fat separation coronary MR angiography (CMRA) in patients with low-to-intermediate risk of coronary artery disease (CAD) and its ability to grade the severity of CAD based on Coronary Artery Disease Reporting and Data System (CAD-RADS). METHODS: A total of 55 patients who was clinically evaluated as low-to-intermediate risk of CAD were finally included to undergo both 3.0 T CS-SENSE water-fat separation CMRA and coronary computed tomography angiography (CCTA), and 11 of them also underwent X-ray coronary angiography (CAG). The severity of coronary artery disease was graded in patients who had completed both CCTA and CMRA examinations by the use of CAD-RADS reports for the patients with stable chest pain, and the diagnostic consistency between the two approaches was evaluated. Diagnostic performance of CMRA was assessed using the combination of CCTA and CAG as the reference standard for excluding or confirming CAD respectively. RESULTS: The sensitivity, specificity, positive predictive value (PPV), negative predictive value (NPV) and diagnostic accuracy of 3.0 T unenhanced water-fat separation coronary MRA were 90.0%, 95.0%, 81.8%, 97.4% and 94.0% for a patient-based analysis respectively. In comparison with CCTA, 3.0 T Dixon water-fat separation CMRA demonstrated excellent consistency in grading the severity of coronary heart disease according to CAD-RADS (0.77 for kappa value). CONCLUSION: In the group of low-to-intermediate probability for CAD, 3.0 T unenhanced CS-SENSE Dixon water-fat separation CMRA can present satisfactory diagnostic performance for the exclusion of CAD with high sensitivity and negative predictive value as well as the evaluation of grading the severity of coronary artery disease.

A clinical strategy to improve the diagnostic performance of 3T non-contrast coronary MRA and noninvasively evaluate coronary distensibility: combination of diastole and systole imaging.

BACKGROUND: The clinical application of coronary MR angiography (MRA) combining diastole and systole imaging has never been described comprehensively in coronary artery disease (CAD) patients. We aimed to design an optimal non-contrast coronary MRA scan protocol combining diastolic and systolic imaging and to (1) evaluate its diagnostic performance for detecting significant coronary stenosis; (2) evaluate the feasibility of this protocol to noninvasively measure the coronary distensibility index (CDI). METHODS: From June 2021 to May 2022, 33 healthy volunteers and 91 suspected CAD patients scheduled for X-ray coronary angiography (CAG) were prospectively enrolled. 3T non-contrast water-fat coronary MRA was carried out twice at diastole and systole. Significant coronary stenosis was defined as a luminal diameter reduction of ≥ 50% using CAG as the reference and was evaluated as follows: (1) by coronary MRA in diastole alone; (2) by coronary MRA in systole alone; (3) by combined coronary MRA in diastole and systole. According to CAG, the patients were divided into significant CAD patients and non-significant CAD patients. The difference in CDI among participants was evaluated. RESULTS: Combined coronary MRA was completed in 31 volunteers and 76 patients. The per-patient sensitivity, specificity, and accuracy of combined coronary MRA were 97.5%, 83.3%, and 90.8%, respectively. Compared with single diastolic mode, combined coronary MRA showed equally high sensitivity but improved specificity on a per-patient basis (83.3% vs. 63.9%, adjusted P = 0.013). The CDI tested by coronary MRA decreased incrementally from healthy volunteers to non-significant and significant CAD patients. CONCLUSION: Compared with single-phase mode, 3 T non-contrast combined coronary MRA significantly improved specificity and may have potential to be a simple noninvasive method to measure CDI.

3.0 T unenhanced Dixon water-fat separation whole-heart coronary magnetic resonance angiography: compressed-sensing sensitivity encoding imaging versus conventional 2D sensitivity encoding imaging.

This study was aimed to investigate 3.0 T unenhanced Dixon water-fat whole-heart CMRA (coronary magnetic resonance angiography) using compressed-sensing sensitivity encoding (CS-SENSE) and conventional sensitivity encoding (SENSE) in vitro and in vivo. The key parameters of CS-SENSE and conventional 1D/2D SENSE were compared in vitro phantom study. In vivo study, fifty patients with suspected coronary artery disease (CAD) completed unenhanced Dixon water-fat whole-heart CMRA at 3.0 T using both CS-SENSE and conventional 2D SENSE methods. We compared mean acquisition time, signal-to-noise ratio (SNR), contrast-to-noise ratio (CNR) and the diagnostic accuracy between two techniques. In vitro study, CS-SENSE achieved better effectiveness between higher SNR/CNR and shorter scan times using the appropriate acceleration factor compared with conventional 2D SENSE. In vivo study, CS-SENSE CMRA had better performance than 2D SENSE in terms of the mean acquisition time, SNR and CNR (7.4 ± 3.2 min vs. 8.3 ± 3.4 min, P = 0.001; SNR: 115.5 ± 35.4 vs. 103.3 ± 32.2; CNR: 101.1 ± 33.2 vs. 90.6 ± 30.1, P < 0.001 for both). The diagnostic accuracy between CS-SENSE and 2D SENSE had no significant difference on a patient-based analysis (sensitivity: 97.3% vs. 91.9%; specificity: 76.9% vs. 61.5%; accuracy: 92.0% vs. 84.0%; P > 0.05 for each). Unenhanced CS-SENSE Dixon water-fat separation whole-heart CMRA at 3.0 T can improve the SNR and CNR, shorten the acquisition time while providing equally satisfactory image quality and diagnostic accuracy compared with 2D SENSE CMRA.

SnO2 mesoporous nanoparticle-based gas sensor for highly sensitive and low concentration formaldehyde detection.

Indoor air quality detection, especially formaldehyde (HCHO) detection, is of great importance in practical application. A key limitation of promoting gas-sensing devices is the lack of sensing materials with high sensing sensitivity and selectivity. In this study, SnO2 mesoporous nanoparticles are fabricated by a facile hydrothermal route with a subsequent acid etching process. The prepared samples show high response toward HCHO (133.5, 222.8 for 100 ppm and 200 ppm HCHO, respectively) and short response/recovery time (15/22 s at 10 ppm). The excellent HCHO sensing performance benefits from the comprehensive regulation of the depletion region width, surface area and rich porosity, which is effective for the promotion of surface adsorption and catalyst activity. It is expected that the excellent sensing properties are promising for practical HCHO gas detection.

Clinical Application of Non-Contrast-Enhanced Dixon Water-Fat Separation Compressed SENSE Whole-Heart Coronary MR Angiography at 3.0 T With and Without Nitroglycerin.

BACKGROUND: 3.0 T non-contrast-enhanced nitroglycerin (NTG)-assisted whole-heart coronary magnetic resonance angiography (MRA) employing Dixon water-fat separation and compressed SENSE (CS-SENSE) acceleration is a promising method for diagnosing coronary artery disease (CAD). PURPOSE: To evaluate the diagnostic performance of this technique for detecting clinically-relevant (≥50% diameter reducing) CAD and to evaluate the difference in NTG-induced coronary vasodilation between patients with and without clinically-relevant CAD. STUDY TYPE: Prospective. POPULATION: Sixty-six patients with suspected CAD. FIELD STRENGTH/SEQUENCE: 3.0 T; CSSENSE, Dixon water-fat separation, three-dimensional segmented turbo field gradient-echo sequence for whole-heart coronary MRA. ASSESSMENT: Overall image quality of coronary MRA was calculated on the basis of all visible coronary segments. The diagnostic performance of coronary MRA for detecting a ≥50% reduction in coronary artery diameter with and without NTG was compared using X-ray coronary angiography (CAG) as the reference. According to CAG, patients were divided into a non-clinically-relevant CAD group and clinically-relevant CAD group, and the difference in NTG-induced vasodilation between the groups was evaluated. STATISTICAL TESTS: Unpaired/paired Student's t-test, Mann-Whitney U test, paired Wilcoxon signed-rank test, χ2 test, McNemar test. A two-tailed P value <0.05 was considered significant. RESULTS: Overall image quality was increased significantly in the coronary MRA images after NTG. The diagnostic performance of the non-NTG vs. NTG-assisted coronary MRA was as follows on a per-patient basis: sensitivity 94.3% vs. 94.3%, specificity 64.5% vs. 83.9%, positive predictive value 75.0% vs. 86.8%, negative predictive value 90.9% vs. 92.9%, and accuracy 80.3% vs. 89.4%, respectively. NTG-induced vasodilation was significantly lower in the clinically-relevant CAD group than in the non-clinically-relevant CAD group (13.7 ± 8.1% vs. 24.1 ± 16.3%). DATA CONCLUSION: Non-contrast Dixon water-fat separation CS-SENSE coronary MRA at 3.0 T can noninvasively detect clinically-relevant CAD and sublingual NTG improved performance. Combining pre- and post-NTG coronary MRA may provide a simple noninvasive and nonionizing test to evaluate coronary vasodilation function. LEVEL OF EVIDENCE: 1 TECHNICAL EFFICACY STAGE: 2.

Assessment of Non-contrast-enhanced Dixon Water-fat Separation Compressed Sensing Whole-heart Coronary MR Angiography at 3.0 T: A Single-center Experience.

RATIONALE AND OBJECTIVES: The clinical utility of Dixon water-fat separation coronary MR angiography (CMRA) with compressed sensing (CS) reconstruction has not been determined in a patient population. This study was designed to evaluate the performance of 3.0 T non-contrast-enhanced Dixon water-fat separation CS whole-heart CMRA sequence in vitro and in vivo. MATERIALS AND METHODS: In vitro phantom MRI, we compared key parameters of the SENSE and CS images. And in this prospective in vivo study, from November 2019 to October 2020, 94 participants were recruited for 3.0 T non-contrast-enhanced Dixon water-fat separation CS whole-heart CMRA. The accuracy of CMRA for detecting a ≥ 50% reduction in diameter was determined using X-ray coronary angiography (CA) as the reference method. RESULTS: Compared with SENSE, CS with an appropriate acceleration factor offers both higher SNR/CNR (p < 0.05) and a shortened acquisition. Fifty-eight patients successfully completed the CMRA and CA. The sensitivity, specificity, positive predictive values, negative predictive values, and accuracy of 3.0 T non-contrast-enhanced Dixon water-fat separation CS whole-heart CMRA according to a patient-based analysis were 96.4%, 66.7%, 73.0%, 95.2% and 81.0%, respectively. The area under the receiver-operator characteristic (ROC) curve (AUC) of 3.0 T non-contrast-enhanced Dixon water-fat separation CS whole-heart CMRA for detecting significant coronary artery stenosis is 0.908, 0.895, and 0.904 in patient-, vessel-, and segment-based analyses respectively. CONCLUSION: 3.0 T non-contrast-enhanced Dixon water-fat separation whole-heart CMRA using appropriate CS is a promising noninvasive and radiation-free technique to detect clinically significant coronary stenosis on patients with suspected CAD.

Role of free-breathing motion-corrected late gadolinium enhancement technique for image quality assessment and LGE quantification.

OBJECTIVE: To compare the image quality and late gadolinium enhancement (LGE) quantification between free-breathing motion-corrected and conventional breath-hold LGE method in a variety of cardiovascular diseases. MATERIALS AND METHODS: 149 consecutive patients underwent contrast-enhanced cardiac magnetic resonance examination employing both free-breathing motion-corrected LGE and conventional breath-hold LGE method. Scan time, contrast-to-noise ratio, overall image quality score and LGE mass were measured and analyzed statistically. RESULTS: Free-breathing motion-corrected LGE method had a shorter scan time and higher overall image quality score in comparison with conventional breath-hold LGE method (p < 0.001). Univariate/multivariate logistic regression analysis showed that breath-holding difficulty, high heart rate and arrhythmia could be predictive factors possibly for an inferior image quality score (p < 0.05 for all). The contrast-to-noise ratios of free-breathing motion-corrected LGE images were higher than those of conventional breath-hold LGE images (p < 0.001). In the cases with subepicardial and/or transmural myocardial enhancement, the measured LGE masses were larger on free-breathing motion-corrected LGE images in comparison with those on conventional breath-hold LGE images (p < 0.05). CONCLUSION: Free-breathing motion-corrected LGE could be a better choice for patients who need contrast-enhanced cardiac MRI and have one or more of the risk factors for an inferior image quality score, including breath-holding difficulty, high heart rate and arrhythmia. However, an overestimation of LGE mass on free-breathing motion-corrected LGE image should be taken into consideration when LGE pattern involves subepicardial and/or transmural myocardium.

Left Ventricular Outflow Tract Obstruction in Hypertrophic Cardiomyopathy: The Utility of Myocardial Strain Based on Cardiac MR Tissue Tracking.

BACKGROUND: Myocardial strain for assessment of hypertrophic cardiomyopathy (HCM) is of importance and may play a role in identifying obstruction in HCM patients. PURPOSE: To evaluate the utility of myocardial strain for detecting left ventricular (LV) outflow tract (LVOT) obstruction in HCM patients based on magnetic resonance tissue tracking. STUDY TYPE: Retrospective. POPULATION: In all, 44 adult HCM patients with LVOT obstruction and 108 adult HCM patients without LVOT obstruction. FIELD STRENGTH/SEQUENCE: 1.5 T; Steady-state free-precession cine sequence; phase-sensitive inversion-prepared segmented gradient echo sequence for late gadolinium enhancement (LGE) imaging. ASSESSMENT: Strain parameters including the local and global levels of LV myocardium and the subtraction (Sub) of myocardial strain variables between interventricular septal segments (IVSS) and noninterventricular septal segments (NIVSS) were measured for differentiating HCM with obstruction from nonobstruction. Average and maximum LV wall thickness (Average and Maximum LVWT) were also analyzed. STATISTICAL TESTS: Univariate and multivariate logistic regression analysis, area under the receiver operating characteristic (ROC) curve (AUC), intraclass correlation coefficient. RESULTS: In multivariate analysis, Average LVWT, Maximum LVWT, and the subtraction of radial peak strain (Sub Radial PS) between NIVSS and IVSS were independently associated with LVOT obstruction. The AUCs were 0.731, 0.840, and 0.890 for Average LVWT, Maximum LVWT, and Sub Radial PS, respectively. Sub Radial PS (cutoff value: 8.1%) demonstrated the highest sensitivity of 75.0% and a high specificity of 87.9% for identifying LVOT; Maximum LVWT (cutoff value: 22.9 mm) showed good sensitivity (72.7%) and specificity (83.3%). Combining Maximum LVWT >22.9 mm and Sub Radial PS > 8.1% achieved a better diagnostic performance (specificity 95.4%, sensitivity 70.5%). DATA CONCLUSION: Combining Maximum LVWT >22.9 mm and Sub Radial PS >8.1% holds promise for objectively evaluating LVOT obstruction in HCM patients with very high specificity and acceptable sensitivity. LEVEL OF EVIDENCE: 3 TECHNICAL EFFICACY STAGE: 2.

Gas Sensing Performance and Mechanism of CuO(p)-WO3(n) Composites to H2S Gas.

In this work, the compositional optimization in copper oxide/tungsten trioxide (CuO/WO3) composites was systematically studied for hydrogen sulfide (H2S) sensing. The response of CuO/WO3 composites changes from p-type to n-type as the CuO content decreases. Furthermore, the p-type response weakens while the n-type response strengthens as the Cu/W molar ratio decreases from 1:0 to 1:10. The optimal Cu/W molar ratio is 1:10, at which the sensor presents the ultrahigh n-type response of 1.19 × 105 to 20 ppm H2S gas at 40 °C. Once the temperature rises from 40 °C to 250 °C, the CuO/WO3 (1:1) sensor presents the p-n response transformation, and the CuO/WO3 (1:1.5) sensor changes from no response to n-type response, because the increased temperature facilitates the Cu-S bonds break and weakens the p-type CuO contribution to the total response, such that the CuS bond decomposition by a thermal effect was verified by a Raman analysis. In addition, with a decrease in CuO content, the CuO is transformed from partly to completely converting to CuS, causing the resistance of CuO to decrease from increasing and, hence, a weakening mode of p-CuO and n-WO3 to the total response turns to a synergistic mode to it.

Studies on Sensing Properties and Mechanism of CuO Nanoparticles to H2S Gas.

In this work, the high crystalline copper oxide (CuO) nanoparticles were fabricated by a hydrothermal method, and their structural properties were characterized by transmission electron microscopy (TEM), X-ray diffraction (XRD), and X-ray photoelectron spectroscopy (XPS). The sensing results show that CuO nanoparticles exhibit enhanced sensitivity and good selectivity for hydrogen sulfide (H2S) gas at a low temperature. There are two working mechanisms involved in the H2S sensing based on CuO nanoparticle sensors. They are the H2S oxidation mechanism and the copper sulphide (CuS) formation mechanism, respectively. The two sensing mechanisms collectively enhance the sensor's response in the H2S sensing process. The Cu-S bonding is stable and cannot break spontaneously at a low temperature. Therefore, the CuS formation inhibits the sensor's recovery process. Such inhibition gradually enhances as the gas concentration increases from 0.2 ppm to 5 ppm, and it becomes weaker as the operating temperature rises from 40 °C to 250 °C. The XPS results confirmed the CuS formation phenomenon, and the micro Raman spectra demonstrated that the formation of CuS bonding and its decomposition can be effectively triggered by a thermal effect. Gas-sensing mechanism analysis supplied abundant cognition for the H2S sensing phenomena based on CuO materials.

Three-Dimensional Free-Breathing Whole-Heart Coronary Magnetic Resonance Angiography at 1.5 T: Gadobutrol-Enhanced Gradient-Echo Acquisition Sequence Versus Non-Contrast-Enhanced Steady-State Free Precession Sequence.

OBJECTIVES: The objective of this study was to compare gadobutrol-enhanced gradient-echo sequence (GRE) acquisition with T2-prepared non-contrast-enhanced steady-state free precession (SSFP) in coronary magnetic resonance angiography at 1.5 T. METHODS: Twenty-one subjects successfully completed GRE and SSFP acquisition. Signal-to-noise ratio (SNR), contrast-to-noise ratio, image quality, sharpness, visibility, length, and lumen diameter of vessels were analyzed by 2 experienced radiologists. RESULTS: The SNR at whole left circumflex artery, left main artery, and proximal left descending artery (LAD) was significantly higher in SSFP acquisition (P < 0.05). The SNR of distal LAD was slightly higher in GRE acquisition (P < 0.05). The contrast-to-noise ratio at distal LAD, proximal and distal RCA were significantly higher with GRE acquisition (P < 0.05). CONCLUSIONS: Double-dose gadobutrol-enhanced GRE and unenhanced SSFP coronary magnetic resonance angiography at 1.5 T have their own characteristics, and the combined use of the 2 methods may be taken into consideration.

Dynamic Imine Bond-Based Shape Memory Polymers with Permanent Shape Reconfigurability for 4D Printing.

Shape memory polymer (SMP)-based 4D printing combines the advantages of SMP and 3D printing to form active materials with delicate structure. Nowadays, studies of SMP-based 4D printing materials mainly focus on cross-linked (meth)acrylate of which the permanent shape cannot be changed for their covalent linkage, limiting the usage of 4D printing materials. In this paper, a novel (meth)acrylate monomer with an aldehyde group (2-(methacryloyloxy)ethyl 4-formylbenzoate, MEFB) and hyperbranched cross-linker (HPASi) are synthesized to build (meth)acrylate systems (IEMSis) with dynamic imine bonds for 4D printing. The flexible chain structure of HPASi significantly enhances the toughness of IEMSis, which is 33-97-fold higher than that of the one without HPASi (IEM). The addition of HPASi also endows IEMSis good shape memory properties, and the shape fixity and shape recovery ratios of them are 97.5-97.6 and 91.4-93.7%, respectively. At the same time, IEMSis can undergo a stress relaxation process by dynamic exchanges of imine bonds under relatively mild conditions without a catalyst to acquire an ability of permanent shape reconfiguration. The shape retention ratio of IEMSi3 is 84.3%. In addition, the 4D-printed structures displayed here indicate that these 4D printing systems have a myriad of potential applications including aerospace structures, soft robotic grippers, smart electron switches, and intelligent packaging, while the reconfigurability shown by IEMSi3 will expand the scope of application fields of 4D printing materials.

Enhanced gas selectivity induced by surface active oxygen in SnO/SnO2 heterojunction structures at different temperatures.

The development of heterojunction structures has been considered as an important step for sensing materials. In this report, 3D hierarchical SnO-SnO2 heterojunction structures were synthesized and developed via simple one-pot hydrothermal synthesis without any extra processes. The prepared 3D samples exhibit high sensitivity, benefiting from the synergistic effects of SnO and SnO2. Interestingly, SnO-SnO2 hybrid structures exhibited distinctly different sensitivities at 180 and 280 °C, and the sensitivity can achieve values of 47.69 and 41.56 toward ethanol and acetone, respectively, at concentrations of 100 ppm. A mechanistic analysis of the sensitivity and concentration-dependence revealed that the oxygen species on the surface were O- and O2- at different temperatures. Therefore, the temperature selectivity of the sample may be due to the different activities of the active oxygen species. Moreover, the composition also shows excellent stability at operating temperatures. The high sensing sensitivity and selectivity is promising for practical VOC gas detection; this also offers a new perspective for the design of multifunctional sensing materials.

Improving gas sensing performance by oxygen vacancies in sub-stoichiometric WO3-x.

Sub-stoichiometric WO3-x has provided an alternative platform to investigate oxygen vacancies in gas sensors based on metal-oxides. We present an experimental study on the influence of sub-stoichiometric WO3-x phase upon gas sensing performance. High-quality WO3-x nanostructures with several x values (WO3, W19O55, W5O14, W18O49) were synthesized and used to fabricate H2S gas sensors. Temperature programmed desorption of oxygen (O2-TPD) shows that oxygen absorption behaviors of the as-prepared WO3-x nanostructures are affected by oxygen vacancies, which played a critical role in the detection of H2S at varying temperature range. We find that oxygen vacancies in sub-stoichiometric WO3-x facilitate the ionosorption process and in turn enhance the performance of the gas sensor.

The role of oxygen vacancies in the sensing properties of Ni substituted SnO2 microspheres.

The influence of Ni doping in SnO2 microspheres was investigated in this study. SnO2 was doped with different amounts of Ni using a simple dipping method. The doped SnO2 structure, which was confirmed from X-ray photoelectron (XPS) and photoluminescence (PL) spectroscopies, was shown to possess distinctly more oxygen vacancies. Oxygen vacancies were found to be responsible for the surface adsorption of oxygen, as shown in the O 1s XPS spectrum and O2-TPD (temperature programmed desorption) measurements which can enhance the sensitivity of materials. According to the gas sensing properties, Ni-doped SnO2 was enhanced towards ethanol and showed excellent stability at the operating temperature. At 1 ppm of ethanol vapor, the response value of Ni substituted SnO2 was about 3 times that of pristine SnO2 microspheres. This research reveals a notable perspective for the design of sensing materials in terms of Ni substitutional doping.

Assessment of the acute effects of glucocorticoid treatment on coronary microembolization using cine, first-pass perfusion, and delayed enhancement MRI.

PURPOSE: To assess the acute effects of methylprednisone treatment (MPT) on coronary microembolization (CME) by cardiac cine, first-pass perfusion, and delayed gadolinium enhancement magnetic resonance imaging (DE-MRI) in an experimental swine model. MATERIALS AND METHODS: Microembolization was established by intracoronary infusion of microspheres into the left anterior artery. Swine received placebo (n = 12) or methylprednisolone (n = 10, 30 mg/kg) intravenously 30 minutes before microembolization. Perfusion and DE-MRI was performed 6 hours after microembolization. Cine MR images of pre-/post-CME were obtained using 1.5T scanner. RESULTS: Cine MRI demonstrated relative amelioration of the post-CME myocardial contractile dysfunction in the glucocorticoid-treated group compared to the placebo group (P < 0.001). Post-CME target myocardial perfusion parameters decreased in both groups after microembolization. The extent of these decreases were the same for the embolized-to-control area ratio of maximum upslope (P = 0.245; 95% confidence interval of the difference [CID], -0.041/0.148) and time to peak ratio (P = 0.122; 95% CID, -0.201/0.026); however, the maximum signal intensity was higher in the glucocorticoid-treated group (P = 0.012; 95% CID, 0.023/0.156). DE-MRI revealed patchy hyperenhancement in all placebo pigs (n = 12/12) after microembolization, but no hyperenhanced regions in the glucocorticoid-pretreated pigs (n = 0/10). CONCLUSION: Standard, readily available, cardiac MRI techniques are useful in demonstrating post-CME myocardial dysfunction and the acute effects of glucocorticoid treatment on CME. Glucocorticoid pretreatment improves myocardial contractile dysfunction, prevents hyperenhancement, and partially ameliorates the decline of myocardial perfusion in the embolized area.

An olive-shaped SnO2 nanocrystal-based low concentration H2S gas sensor with high sensitivity and selectivity.

Olive-shaped SnO2 nanocrystals were synthesized successfully via a facile hydrothermal route, using tin dichloride hydrate, oxalic acid dihydrate and polyvinylpyrrolidone as reaction precursors, and showed great potential in the large-scale preparation of SnO2 nanocrystals. The prepared SnO2 nanocrystals were characterized using XRD, XPS, SEM, TEM and HRTEM, and showed well-defined olive-shaped tetragonal single-crystals with irregular exposed facets. The growth mechanism of the olive-shaped SnO2 nanocrystals was considered after investigating the experimental conditions and reaction time. Due to the abundant active sites on the irregular surfaces, the gas sensing performance of the prepared SnO2 nanocrystals exhibited great gas sensing properties, including high sensitivity, selectivity and stability towards H2S with a very low detection limit (less than 0.5 ppm), revealing their great potential in commercial applications for H2S gas detection.

3D coronary MR angiography at 1.5 T: Volume-targeted versus whole-heart acquisition.

PURPOSE: To compare volume-targeted acquisition with whole-heart acquisition in 1.5-T free-breathing 3D coronary magnetic resonance angiography (MRA) with parallel imaging. MATERIALS AND METHODS: The major coronary arteries were imaged in 36 subjects using the whole-heart and volume-targeted acquisitions with comparable imaging parameters. The quantitative and semiquantitative data derived from these two acquisition methods were analyzed statistically, with P < 0.05 considered significant. RESULTS: Both the right coronary artery (RCA) / left circumflex artery (LCX)- and the left main (LM) / left anterior descending (LAD)-targeted acquisitions had similar results in navigator efficiencies and apparent signal-to-noise ratio (SNR) in comparison with whole-heart acquisition. Apparent contrast-to-noise ratio (CNR) of the volume-targeted imaging was significantly higher than that of the whole-heart imaging. The imaging time required for a whole-heart scan was significantly longer than each of the RCA/LCX- and LM/LAD-targeted acquisitions. However, the sum of scanning times derived from volume-targeted imaging was significantly longer than that of whole-heart acquisition. Both RCA/LCX- and LM/LAD-targeted acquisition yield higher vessel sharpness and overall image quality in comparison with whole-heart acquisition. The lengths of the major coronary arteries were not significantly different for the whole-heart and volume-targeted approaches. The whole-heart method was obviously superior to the volume-targeted method in terms of visualization of the posterior descending artery. CONCLUSION: For current 1.5-T navigator coronary MRA, volume-targeted and whole-heart acquisitions have their own advantages and the choice of methods may vary in accordance with the different aims of clinical practice.