Insight into the Imbibition Behavior of Low-Frequency Artificial Vibration Stimulation in Tight Sandstone.

Spontaneous imbibition is the primary mechanism responsible for the enhanced oil production in a tight reservoir after hydraulic fracturing. In this article, a low-frequency artificial vibration physics stimulation method was employed to evaluate the effect of low-frequency vibration on imbibition recovery in tight sandstones. Furthermore, a high-precision in situ computed tomography (CT) scan was employed to investigate the effect of low-frequency vibration on the distribution of remaining oil micro-occurrence dynamic alterations in pore space. The findings of the study show that (1) low-frequency artificial physical vibration stimulation has been found to be highly effective in enhancing imbibition recovery in tight sandstone. The sensitivity of the vibration parameters on imbibition recovery from highest to lowest is vibration frequency, vibration intensity, and vibration time. The optimum vibration parameters for this process are a vibration frequency of 30 Hz, a vibration intensity of 2.0 m/s2, and a vibration time of 30 h. (2) Under the optimum low-frequency vibration, the imbibition recovery of tight sandstone with various physical properties can reach between 13.6 and 28.3%. This is remarkably higher than the spontaneous imbibition recovery, which ranges from 9.4 to 17.1%. Additionally, core samples with higher permeability and better pore structure show a more significant increase in imbibition recovery under the vibration treatment. Furthermore, low-frequency vibration stimulation effectively shortens the imbibition completion time, reducing the completion time from 81 h to approximately 55 h. (3) After the spontaneous imbibition process, the initial continuous oil phase present in the pore space is dispersed by the water phase imbibition process. The remaining oil is dominant in the form of a network type, which is concentrated in the central pore space area of the core. Low-frequency vibration treatment can effectively promote a positive imbibition process. The network remaining oil saturation in the core can be further dispersed, especially closer to the surface of the core area after frequency vibration treatment. Then, the cluster remaining oil type with a more dispersed and simpler individual structure has become the new dominant remaining oil micro-occurrence form in the pore space. The findings of this research investigate a novel technological approach to enhance the imbibition efficiency of a tight sandstone reservoir.

A bio-based durable reactive flame retardant for cotton fabric based on lentinan.

Cotton fabric has extensive application due to its comfort and breathability. However, the inherent flammability limits its wide application. Durable polysaccharide-based flame retardants with a low impact on the softness of fabrics are rarely reported. In this work, a novel flame retardant ammonium phosphate of lentinan (APLNT) was synthesized and grafted on the surface of cotton fabric. The treated cotton fabric had a high limiting oxygen index (LOI) value of 43.3 % and passed the vertical burning test (VBT) with a 21.1 % weight gain of APLNT. Compared with control cotton, the peak heat release rate and total heat release values of Cotton-APLNT2 decreased by 92.8 % and 50.9 %, respectively. In addition, the cotton fabric still passed the VBT and kept an LOI value of 27.0 % even after 50 laundering cycles, indicating that the fabric can be used for daily needs. More importantly, the treated fabric remains soft. This research provided a new strategy for preparing bio-based durable flame retardant cotton fabrics.

A Novel Fracturing Fluid Based on Functionally Modified Nano-Silica-Enhanced Hydroxypropyl Guar Gel.

Considering the damage caused by conventional fracturing fluid in low-permeability reservoirs, a novel fracturing fluid (FNG) combining hydroxypropyl guar (HPG) and functionally modified nano-silica (FMNS) was prepared. The properties of heat/shear resistance, rheological property, proppant transportation, and formation damage were evaluated with systematic experiments. The results showed that the viscosities of FNG before and after the heat/resistance were 1323 mPa·s and 463 mPa·s, respectively, while that of conventional HPG gel was 350 mPa·s. FNG is a pseudoplastic strong gel with a yield stress of 12.9 Pa, a flow behavior index of 0.54, an elastic modulus of 16.2 Pa, and a viscous modulus of 6.2 Pa. As the proportions of proppant mass in further sections transported with FNG were higher than those transported with HPG gel, FNG could transport the proppant better than HPG gel at high temperatures. Because of the amphiphilic characteristics of FMNS, the surface/interface properties were improved by the FNG filtrate, resulting in a lower oil permeability loss rate of 10 percentage points in the matrix than with the filtrated HPG gel. Due to the considerable residual gel in broken HPG gel, the retained conductivity damaged with broken FNG was 9.5 percentage points higher than that damaged with broken HPG gel. FNG shows good potential for reducing formation damage during fracturing in low-permeability reservoirs in China.

Gelation and Plugging Performance of Low-Concentration Partially Hydrolyzed Polyacrylamide/Polyethyleneimine System at Moderate Temperature and in Fractured Low-Permeability Reservoir.

HPAM/PEI gel is a promising material for conformance control in hydrocarbon reservoirs. However, its use in low-permeability reservoirs is limited by the high polymer concentrations present. In this study, the gelation performance of an HPAM/PEI system with HPAM < 2.0 wt.% was systematically investigated. The gelation time for HPAM concentrations ranging from 0.4 to 2.0 wt.% varied from less than 1 h to 23 days, with the highest gel strength identified as grade H. The hydrodynamic radius manifested the primary effect of HPAM on the gelation performance. Branched PEI provided superior gelation performance over linear PEI, and the gelation performance was only affected when the molecular weight of the PEI varied significantly. The optimal number ratio of the PEI-provided imine groups and the HPAM-provided carboxylic acid functional groups was approximately 1.6:1~5:1. Regarding the reservoir conditions, the temperature had a crucial effect on the hydrodynamic radius of HPAM. Salts delayed the gelation process, and the order of ionic influence was Ca2+ > Na+ > K+. The pH controlled the crosslinking reaction, primarily due to the protonation degree of PEI and the hydrolysis degree of HPAM, and the most suitable pH was approximately 10.5. Plugging experiments based on a through-type fracture showed that multi-slug plugging could significantly improve the plugging performance of the system, being favorable for its application in fractured low-permeability reservoirs.

Air pollution and skin diseases: A comprehensive evaluation of the associated mechanism.

Air pollutants deteriorate the survival environment and endanger human health around the world. A large number of studies have confirmed that air pollution jeopardizes multiple organs, such as the cardiovascular, respiratory, and central nervous systems. Skin is the largest organ and the first barrier that protects us from the outside world. Air pollutants such as particulate matter (PM), polycyclic aromatic hydrocarbons (PAHs), volatile organic compounds (VOCs) will affect the structure and function of the skin and bring about the development of inflammatory skin diseases (atopic dermatitis (AD), psoriasis), skin accessory diseases (acne, alopecia), auto-immune skin diseases (cutaneous lupus erythematosus(CLE) scleroderma), and even skin tumors (melanoma, basal cell carcinoma (BCC), squamous-cell carcinoma (SCC)). Oxidative stress, skin barrier damage, microbiome dysbiosis, and skin inflammation are the pathogenesis of air pollution stimulation. In this review, we summarize the current evidence on the effects of air pollution on skin diseases and possible mechanisms to provide strategies for future research.

Polyvinyl Chloride-Based Luminescent Downshifting Film with High Flame Retardancy and Excellent UV Resistance for Silicon Solar Cells.

Solar power generation, as a clean energy source, has significant potential for development. This work reports the recent efforts to address the challenge of low power conversion efficiency in photovoltaic devices by proposing the fabrication of a luminescence downshifting layer using polyvinyl chloride (PVC) with added fluorescent dots to enhance light utilization. A photoluminescent microsphere (HCPAM) is synthesized by cross-linking hexachlorocyclotriphosphazene, 2-iminobenzimidazoline, and polyethyleneimine. Low addition of HCPAM can improve the fire safety of PVC films, raising the limiting oxygen index of PVC to 32.4% and reducing the total heat release and smoke production rate values by 14.5% and 42.9%, respectively. Additionally, modified PVC film remains a transparency of 88% and shows down-conversion light properties. When the PVC+1%HCPAM film is applied to the solar cell, the short-circuit current density increases from 42.3 to 43.8 mA cm-2, resulting in a 7.0% enhancement in power conversion efficiency. HCPAM also effectively delays the photooxidative aging of PVC, particularly at a 3% content, maintaining the surface morphology and optical properties of PVC samples during ultraviolet aging. This study offers an innovative strategy to enhance the fire and UV-resistant performance of PVC films and expand their applications in protecting and efficiently utilizing photovoltaic devices.

A Fluorination Strategy and Low-Acidity Anchoring Group in Self-Assembled Molecules for Efficient and Stable Inverted Perovskite Solar Cells.

Herein, we synthesized two donor-acceptor (D-A) type small organic molecules with self-assembly properties, namely MPA-BT-BA and MPA-2FBT-BA, both containing a low acidity anchoring group, benzoic acid. After systematically investigation, it is found that, with the fluorination, the MPA-2FBT-BA demonstrates a lower highest occupied molecular orbital (HOMO) energy level, higher hole mobility, higher hydrophobicity and stronger interaction with the perovskite layer than that of MPA-BT-BA. As a result, the device based-on MPA-2FBT-BA displays a better crystallization and morphology of perovskite layer with larger grain size and less non-radiative recombination. Consequently, the device using MPA-2FBT-BA as hole transport material achieved the power conversion efficiency (PCE) of 20.32 % and remarkable stability. After being kept in an N2 glove box for 116 days, the unsealed PSCs' device retained 93 % of its initial PCE. Even exposed to air with a relative humidity range of 30±5 % for 43 days, its PCE remained above 91 % of its initial condition. This study highlights the vital importance of the fluorination strategy combined with a low acidity anchoring group in SAMs, offering a pathway to achieve efficient and stable PSCs.

Plant immunity suppression by an ß-1,3-glucanase of the maize anthracnose pathogen Colletotrichum graminicola.

BACKGROUND: Many phytopathogens secrete a large number of cell wall degrading enzymes (CWDEs) to decompose host cell walls in order to penetrate the host, obtain nutrients and accelerate colonization. There is a wide variety of CWDEs produced by plant pathogens, including glycoside hydrolases (GHs), which determine the virulence, pathogenicity, and host specificity of phytopathogens. The specific molecular mechanisms by which pathogens suppress host immunity remain obscure. RESULT: In this study, we found that CgEC124 encodes a glycosyl hydrolase with a signal peptide and a conserved Glyco_hydro_cc domain which belongs to glycoside hydrolase 128 family. The expression of CgEC124 was significantly induced in the early stage of Colletotrichum graminicola infection, especially at 12 hpi. Furthermore, CgEC124 positively regulated the pathogenicity, but it did not impact the vegetative growth of mycelia. Ecotopic transient expression of CgEC124 decreased the disease resistance and callose deposition in maize. Moreover, CgEC124 exhibited the ß-1,3-glucanase activity and suppresses glucan-induced ROS burst in maize leaves. CONCLUSIONS: Our results indicate that CgEC124 is required for full virulence of C. graminicola but not for vegetative growth. CgEC124 increases maize susceptibility by inhibiting host reactive oxygen species burst as well as callose deposition. Meanwhile, our data suggests that CgEC124 explores its ß-1,3-glucanase activity to prevent induction of host defenses.

Enhancing the flame retardancy of polylactic acid nonwoven fabric through solvent-free transparent coating.

Polylactic acid (PLA) nonwovens, recognized as eco-friendly substitutes for petroleum-based synthetic fibers, face a significant challenge due to their inherent flammability. This work addresses this concern by synthesizing a hyperbranched polyphosphoramide flame retardant (TPDT) through a one-step polycondensation process without using solvent and catalyst. TPDT is subsequently applied to PLA nonwovens using a dip-pad finishing technique. Notably, with a mere 7 wt% weight gain of TPDT, the PLA nonwovens exhibit a substantial increase in the limited oxygen index (LOI) value, reaching 32.3 %. Furthermore, the damaged area in the vertical burning test is reduced by approximately 69.2 %. In the cone calorimeter test, 17 wt% weight gain of TPDT results in a 51.4 % decrease in peak heat release rate and a 56.0 % reduction in total heat release compared to the control PLA. Additionally, char residue increases from 1.5 wt% to 31.1 wt% after combustion. The strong affinity between TPDT and PLA molecules persists even after repeated abrasion, ensuring sustained flame retardancy. Importantly, the introduction of TPDT also imparts increased softness to the PLA nonwovens. This work addresses this concern by synthesizing a hyperbranched polyphosphoramide flame retardant (TPDT) through a solvent-free, catalyst-free, and one-step polycondensation process.

In Situ Growth Strategy to Construct "Four-In-One" Separators with Functionalized Polyphosphazene Coatings for Safe and Stable Lithium-Sulfur Batteries.

Lithium-sulfur batteries (LSBs) are facing many challenges, such as the inadequate conductivity of sulfur, the shuttle effect caused by lithium polysulfide (LiPSs), lithium dendrites, and the flammability, which have hindered their commercial applications. Herein, a "four-in-one" functionalized coating is fabricated on the surface of polypropylene (PP) separator by using a novel flame-retardant namely InC-HCTB to meet these challenges. InC-HCTB is obtained by cultivating polyphosphazene on the surface of carbon nanotubes with an in situ growth strategy. First, this unique architecture fosters an enhanced conductive network, bolstering the bidirectional enhancement of both ionic and electronic conductivities. Furthermore, InC-HCTB effectively inhibits the shuttle effect of LiPSs. LSBs exhibit a remarkable capacity of 1170.7 mA h g-1 at 0.2 C, and the capacity degradation is a mere 0.0436% over 800 cycles at 1 C. Third, InC-HCTB coating serves as an ion migration network, hindering the growth of lithium dendrites. More importantly, InC-HCTB exhibits notable flame retardancy. The radical trapping action in the gas phase and the protective effect of the shielded char layer in the condensed phase are simulated and verified. This facile in situ growth strategy constructs a "four-in-one" functional separator coating, rendering InC-HCTB a promising additive for the large-scale production of safe and stable LSBs.

The involvement of interferon regulatory factor 8 in regulating the proliferation of haemocytes in oyster Crassostrea gigas.

Interferon regulatory factor 8 (IRF8) is an important transcriptional regulatory factor involving in multiple biological process, such as the antiviral immune response, immune cell proliferation and differentiation. In the present study, the involvement of a previously identified IRF8 homologue (CgIRF8) in regulating haemocyte proliferation of oyster were further investigated. CgIRF8 mRNA transcripts were detectable in all the stages of C. gigas larvae with the highest level in D-veliger (1.76-fold of that in zygote, p < 0.05). Its mRNA transcripts were also detected in all the three haemocyte subpopulations of adult oysters with the highest expression in granulocytes (2.79-fold of that in agranulocytes, p < 0.01). After LPS stimulation, the mRNA transcripts of CgIRF8 in haemocytes significantly increased at 12 h and 48 h, which were 2.04-fold and 1.65-fold (p < 0.05) of that in control group, respectively. Meanwhile, the abundance of CgIRF8 protein in the haemocytes increased significantly at 12 h after LPS stimulation (1.71-fold of that in seawater, p < 0.05). The immunofluorescence assay and Western blot showed that LPS stimulation induced an obvious nucleus translocation of CgIRF8 protein in haemocytes. After the expression of CgIRF8 was inhibited by the injection of CgIRF8 siRNA, the percentage of EdU positive haemocytes, the proportion of granulocytes, and the mRNA expression levels of CgGATA and CgSCL all declined significantly at 12 h after LPS stimulation, which was 0.64-fold (p < 0.05), 0.7-fold (p < 0.05), 0.31-fold and 0.54-fold (p < 0.001) of that in the NC group, respectively. While the expression level of cell proliferation-related protein CgCDK2, CgCDC6, CgCDC45 and CgPCNA were significantly increased (1.99-fold, and 2.41-fold, 3.76-fold and 4.79-fold compared to that in the NC group respectively, p < 0.001). Dual luciferase reporter assay demonstrated that CgIRF8 was able to activate the CgGATA promoter in HEK293T cells after transfection of CgGATA and CgIRF8. These results collectively indicated that CgIRF8 promoted haemocyte proliferation by regulating the expression of CgGATA and other related genes in the immune response of oyster.

Surface modification of zinc oxide and its application in polypropylene with excellent fire performance and ultra-violet resistance.

Despite the advantages of easy moulding and excellent mechanical properties, there are still some shortcomings with polypropylene (PP) such as high flammability and poor ultra-violet (UV) resistance. In this work, modified zinc oxide (mZnO) was prepared by reacting zinc oxide nanoparticles (ZnO) with polysiloxanes, and the effect of mZnO on the effectiveness of intumescent flame-retardant and on the UV aging resistance of polypropylene were investigated. By introducing 16 wt% (intumescent flame-retardant /mZnO) and 0.3 wt% maleic anhydride-grafted PP (MAH-g-PP), the limiting oxygen index increased to 32.7 %, and passed UL-94V-0 rating. In comparison to the controls, the peak heat release rate and the peak smoke release rate were 88.5 % and 80 % lower, respectively. In addition, PP samples showed improved mechanical properties, with a 5 % increase in tensile properties compared to the pure PP sample. After 100 h of UV irradiation, the surface of the samples was relatively flat and smooth, and the carbonyl index decreased from 81.1 of neat PP to 26.7. PP composites with 100 h aging treatment still had excellent flame retardancy and mechanical properties. The results showed that mZnO was effective in improving the flame retardancy, mechanical properties and light aging tolerance of PP. This study provides a novel approach to fabricate long-life flame-retardant PP composites with low additive content.

Study on the Wettability Alteration of Tight Sandstone by Low-Frequency Vibration and Nanofluid.

The efficiency of reservoir imbibition in continental tight sandstone reservoirs is severely hindered due to their intricate wettability characteristics. To address this challenge, we propose a novel synergistic approach that combines low-frequency vibration and nanofluid treatment. This method integrates physical shear and chemical wettability alteration to effectively modify the wettability of neutral oil-wet tight sandstone, thereby enhancing the imbibition process. In this study, we formulated a TX-100 nanofluid system through physical modification. By utilizing the contact angle as a benchmark for evaluation, we investigated the impact of low-frequency fluctuations on the wettability of oil-wet sandstone. Subsequently, we identified the optimal combination of wave parameters. Through isothermal adsorption experiments and mechanical analyses of oil droplets subjected to fluctuations, we systematically elucidated the mechanism by which fluctuations collaborate with nanofluids to alter the wettability of oil-wet sandstone. Furthermore, we evaluated the oil displacement efficiency of cores subjected to the combined action of low-frequency fluctuations and nanofluid treatment. Our findings revealed that the TX-100 nanofluid reduced the static contact angle of oil-wet sandstone by 58%. When assisted by the optimal fluctuation parameters, the nanofluid treatment contributed to a 64% reduction in the contact angle of strongly oil-wet sandstone. This effect further amplified the reversal of wettability in oil-wet sandstone. Through the application of various wave-assisted treatment agents, the efficiency of oil removal was increased by a minimum of 16%. Moreover, the recovery degree of wave-assisted nanofluid imbibition experienced a remarkable enhancement of 30.39%. Nuclear magnetic resonance analysis demonstrated a significant improvement in pore sizes smaller than 1 µm as a result of the composite process.

A universal eco-friendly flame retardant strategy for polylactic acid fabrics and other polymer substrates.

Various polymer substrates have their particular combustion features, therefore, developing an effective universal flame retardant strategy for various polymer substrates is of great practical importance. Meanwhile, as substitutes for petroleum-based products, bio-based flame retardants and biodegradable polylactic acid (PLA) meet the requirements of sustainable development. In this work, a fully bio-based flame retardant coating (PAGS) was prepared using phytic acid (PA) and guanosine (GS). PAGS was used as a universal flame retardant coatings for polylactic acid (PLA) fabrics and other substrates, including cotton fabrics, polyethylene terephthalate (PET) fabrics, polyamide (PA) fabrics, polyurethane (PU) foams, polyethylene terephthalate (PET) films, and woods. The PAGS-treated substrates were able to self-extinguish and eliminate molten droplets. Similarly, the PAGS coating significantly suppressed the heat release of each substrate. The P-containing free radicals in the gas phase were able to interact with highly reactive H, HO and alkyl radicals, blocking the chain reaction during combustion. The flammable gas density was also diluted by nonflammable gases. The formed continuous porous and dense intumescent char layer hindered heat and oxygen. It is suggested that this work provides a simple and efficient flame retardant strategy for improving the fire safety of various polymer substrates.

Antisolvent-Free Heterogenous Nucleation Enabled by Employing 4-Tert-Butyl Pyridine Additive and Two-Step Annealing for Efficient CsPbI2 Br Perovskite Solar Cells.

All inorganic perovskite based on CsPbI2 Br has attracted significant attention due to its relatively thermal stable structure compare to its hybrid counterparts. With a wide bandgap of 1.9 eV and excellent light absorption capability, it has been extensively explored for applications in indoor photovoltaics and as a front absorber in tandem devices. However, the uncontrollable crystallization process during solvent evaporation and thermal annealing leads to both macroscopic defects like cracks and microscopic defects such as voids. In this study, a metastable adduct with lead (II) halides by incorporating 4-tert-butyl pyridine as a volatile Lewis base monodentate ligand in the precursor solution is formed. The strategic preferential decomposition of the adduct during the early-stage low-temperature annealing facilitated the desorption of lead (II) halides, inducing antisolvent-free heterogenous nucleation. This, in turn, promoted crystal growth during subsequent high-temperature annealing, resulting in dense films with low defect density. As a result, a maximum open-circuit voltage of 1.30 V is achieved with the champion power conversion efficiency of 16.5% in CsPbI2 Br-based perovskite solar cell. The work reveals a new mechanism of using Lewis acid-base adduct to obtain high quality perovskite films other than hindering crystallization in traditional way.

Imaging Findings and Misdiagnosis of Bronchogenic Cysts: A Study of 83 Cases.

Objective: We characterize computed tomography (CT) and magnetic resonance imaging (MRI) features of bronchogenic cysts (BCs) and analyze misdiagnosis. Methods: The retrospective study consisted of 83 patients with BCs. CT and MRI images were assessed for mass location, maximum diameter, density, calcification, signal intensity, and enhancement pattern. Eighty-three patients underwent plain CT in which 53 underwent enhanced CT. Thirteen patients received both plain and enhanced MR, and only one received just a plain MR. Results: Eighty-three masses were all solitary, with 71 having a roundish morphology, and twelve having a lobulated or irregular morphology. Sixty-six masses are mediastinal type, four are intrapulmonary type, and 13 are ectopic type. Calcification occurred in 14 lesions. On plain CT, 13 lesions displayed water-like attenuation (-20-20 Hu), and 70 showed soft-tissue attenuation (≥21 Hu). On T1WI, eight masses were hyperintense, three were isointense, and three were hypointense. Fourteen masses were hyperintense on T2WI and (Apparent Diffusion Coefficient) ADC sequence. On (Diffusion Weighted Imaging) DWI, six masses were hypointense and eight were hyperintense. Enhanced T1WI showed seven cases were unenhanced, while six were marginally enhanced. Twenty cases were misdiagnosed as thymomas, eleven as neurogenic tumors, six as lymphangiomas, and two as lung cancer. Five cases were misdiagnosed as other diseases. Patients with BCs underwent MR (42.9%) had a lower rate of misdiagnosis than those who underwent CT alone (53.0%). Conclusion: The imaging findings of BCs in the chest are generally consistent. Misdiagnosis occurs frequently when CT attenuation values exceed 20 Hu. Diagnostic accuracy of BCs tends to improve with preoperative MR examination.

Study on the Flame Retardancy of Rigid Polyurethane Foam with Phytic Acid-Functionalized Graphene Oxide.

A rigid polyurethane foam (RPUF) composite was prepared by compounding phytic acid (PA)-functionalized Graphite oxide (PA-GO) with flame-retardant poly (Ammonium phosphate) (APP) and expandable graphite (EG). The effects of PA-GO on the thermal, flame-retardant, and mechanical properties of RPUF were studied using a thermogravimetric analyzer, a limiting oxygen index (LOI) tester, a UL-94 vertical combustion tester, a cone calorimeter, scanning electron microscopy, and a universal tensile testing machine. The results indicated that there was a significant synergistic flame-retardant effect between PA-GO and the intumescent flame retardants (IFR) in the RPUF matrix. Compared with RPUF-1, the addition of 0.3 wt% PA-GO could increase LOI from 25.7% to 26.5%, increase UL-94 rating from V-2 to V-0, and reduce the peak heat release rate (PHRR) and total heat release rate (THR) by 28.5% and 22.2%, respectively. Moreover, the amount of residual char increased from 22.2 wt% to 24.6 wt%, and the char layer was continuous and dense, with almost no holes. Meanwhile, the loss of mechanical properties was apparently lightened.

Differential diagnostic value of tumor markers and contrast-enhanced computed tomography in gastric hepatoid adenocarcinoma and gastric adenocarcinoma.

Objective: This study aimed to investigate the effectiveness of tumor markers and contrast-enhanced computed tomography (CE-CT) in differentiating gastric hepatoid adenocarcinoma (GHA) from gastric adenocarcinoma (GA). Methods: This retrospective study included 160 patients (44 with GHA vs. 116 with GA) who underwent preoperative CE-CT. Preoperative serum concentrations of tumor biomarkers and CT imaging features were analyzed, including alpha-fetoprotein (AFP), carcinoembryonic antigen (CEA), carbohydrate antigen 19-9 (CA19-9), carbohydrate antigen 125 (CA125), tumor location, growth pattern, size, enhancement pattern, cystic changes, and mass contrast enhancement. Multivariate logistic regression analyses were performed to evaluate useful tumor markers and CT imaging features for differentiating GHA from GA. Results: When compared to GA, GHA showed a higher serum AFP [13.27 ng/ml (5.2-340.1) vs. 2.7 ng/ml (2.2-3.98), P <0.001] and CEA levels [4.07 ng/ml (2.73-12.53) vs. 2.42 ng/ml (1.38-4.31), P <0.001]. CT imaging showed GHA with a higher frequency of tumor location in the gastric antrum (P <0.001). GHA had significantly lower attenuation values at the portal venous phase [PCA, (82.34 HU ± 8.46 vs. 91.02 HU ± 10.62, P <0.001)] and delayed phase [DCA, (72.89 HU ± 8.83 vs. 78.27 HU ± 9.51, P <0.001)] when compared with GA. Multivariate logistic regression analyses revealed that tumor location, PCA, and serum AFP level were independent predictors of differentiation between GHA and GA. The combination of these three predictors performed well in discriminating GHA from GA, with an AUC of 0.903, a sensitivity of 86.36%, and a specificity of 81.90%. Conclusions: Integrated evaluation of tumor markers and CT features, including tumor location, PCA, and serum AFP, allowed for more accurate differentiation of GHA from GA.

Constructing lignin based nanoparticles towards flame retardant thermoplastic polyurethane composites with improved mechanical and oxidation resistant properties.

A multifunctional lignin derivative nanoparticle (C-P-Lignin) was synthesized by grafting phenyl dichloro sphosphineoxid and 1, 4-dimethoxyacetylene stepwise on the lignin, then it was applied to prepare the thermoplastic polyurethane (TPU) composite with improved mechanical properties, oxidation resistance, and flame retardancy. The tensile strength, the elongation at break, and the toughness of the TPU/2C-P-Lignin sample reached 28.3 MPa, 941 %, and 139.0 MJ/m2 respectively, which were increased by 39.0 %, 3.4 %, and 33.9 % respectively compared with that of the control TPU sample. The anti-fatigue property was also improved. More importantly, the mechanism of the improved mechanical properties was also calculated and simulated by FTIR and Materials Studio software. The TPU/2C-P-Lignin sample exhibited superior oxidation resistance during the process of photoaging and thermal oxidative aging. Furthermore, the peak heat release rate and the smoke production rate for theTPU/2C-P-Lignin sample was reduced by 50.0 % and 53.8 % compared with that of the control TPU. The reason was that the C-P-Lignin is conducive to the formation of uniformly distributed carbon layers. It is expected that this work can provide a new method for expanding the utilization of waste wood as a multifunctional lignin-based filler to improve fire safety and extend the service life of TPU polymers.

A first-principles study of the structural, electronic and elastic properties of the FeO2-FeO2He system under high pressure.

The origin of the wave velocity anomalies at the core-mantle boundary (CMB) has been controversial. The primordial helium reservoir in the deep lower mantle remains elusive even with geochemical evidence for its existence. Here, we calculated the density and wave velocity of the FeO2-FeO2He system under the CMB conditions using first principles. The FeO2 and FeO2He of pyrite-type can exist stably under the CMB conditions without melting, and the incorporated helium increases the stability of the system. The electrical properties of FeO2 and FeO2He are not related to pressure. Doped helium reduces the density of the system but increases the elastic modulus. Our results suggest that FeO2 can be used as a viable material composition of ultra-low velocity zones (ULVZs), and FeO2He can explain the D'' seismic discontinuity instead of ULVZs. The primordial helium reservoir possibly formed by the accumulation of FeO2He, the only stable solid helium-bearing compound under the CMB conditions, may coincide with the location of the D'' layer.