The effect of platelet-rich fibrin (PRF) versus freeze-dried bone allograft (FDBA) used in alveolar ridge preservation on the peri-implant soft and hard tissues: a randomized clinical trial.

BACKGROUND: The effectiveness of alveolar ridge preservation on bone regeneration and tissue healing has been thoroughly documented in the literature. This study aimed to evaluate the peri-implant soft and hard tissue changes after alveolar ridge preservation using either platelet-rich fibrin (PRF) or freeze-dried bone allograft (FDBA) over a 12-month period following the prosthetic loading of implants. METHODS: In this randomized clinical trial, 40 individuals were recruited for alveolar ridge preservation using (1) FDBA or (2) PRF in incisal/premolar areas. At two follow-up sessions (six- and 12-months post-implant insertion), radiographic imaging and clinical examinations assessed marginal bone loss and soft tissue factors, including gingival recession and bleeding on probing. The differences between study groups were analyzed using Generalized estimating Equations, the Binary logistic regression model, and Cochran's Q test. RESULTS: There was a statistically significant difference regarding gingival recession at both follow-up evaluations; values in the PRF group were considerably lower compared to the FDBA group (p < 0.05). The mean values for vertical marginal bone loss and bleeding on probing showed no significant differences between the two study groups (p > 0.05). CONCLUSIONS: Except for gingival recession, applying PRF yielded comparable clinical results to FDBA after one year of implant loading and could be recommended as a potential biomaterial for alveolar ridge preservation following tooth extractions. CLINICAL TRIAL REGISTRATION: The research protocol was registered in the Protocol Registration and Results System on 13/08/2021, available at https://clinicaltrials.gov/ (NCT05005377).

Full-ceramic resin-bonded fixed dental prostheses: A systematic review.

Despite the development of implant-supported prostheses, there are still patients for whom conservative treatments such as resin-bonded fixed dental prostheses (RBFDPs) are more appropriate. This study's objective was to analyze the available research on full-ceramic RBFDPs. In this study, Web of Science, MEDLINE/PubMed, Scopus, Embase, Cochrane Library, and Google Scholar databases were searched for articles published in English between 2010 and 2020. A total of 14 studies were reviewed based on the eligibility criteria. The results showed that using a cantilever design with one abutment had an advantage over two abutments. Additionally, it was proposed that preparations designed with retentive aids, such as a proximal box, groove, and pinhole, could improve RBFDP survival rates. IPS e.max ZirCAD, In-Ceram alumina, and zirconia CAD/CAM were the most commonly used framework materials. Most studies used air abrasion, salinization, or hydrofluoric acid for surface treatment. Adhesive resin cements were the most frequently used type of cement. The survival rate of In-Ceram ceramics (85.3%-94.8%) was lower than that of In-Ceram zirconia and IPS e.max ZirCAD. Debonding, followed by framework fracture, was the leading cause of failure. Following 3-10 years follow-up, the survival percentage of all-ceramic RBFDPs ranged from 76% to 100%. Although RBFDPs have demonstrated satisfactory success as a conservative treatment, long-term follow-ups and higher sample sizes in clinical research are required to gain more reliable outcomes on the clinical success rate of various RBFDP designs.

Comparison of marginal and internal adaptation of provisional polymethyl methacrylate restorations fabricated by two three-dimensional printers: An in vitro study.

Background: Chairside fabrication of provisional restorations using three-dimensional (3D) printers is rising in digital dentistry. The purpose of this research was to compare the marginal and internal adaptation of provisional polymethyl methacrylate (PMMA) restorations fabricated by two different 3D printers. Materials and Methods: In this in vitro investigation, an intact maxillary 1st molar acrylic model was first digitalized by a laboratory scanner. It was then prepared for an all-ceramic restoration and scanned again by the same scanner. The final restoration was designed in Exocad according to the scan files with a 50 µm cement gap. PMMA restorations were printed by two 3D printers; Group 1: Asiga (n = 10) and Group 2: Digident (n = 10). The replica technique was used to assess the marginal and internal fit of the restorations, and one-way ANOVA was used to analyze the data. P <0.05 was regarded as statistically significant. Results: The mean marginal gap of crowns in Group 1 was significantly lower than that of Group 2 (75 vs. 195 µm, P = 0.001). Regarding internal adaptation, no significant difference was found between the axial gap values in both groups (P > 0.05). The mean occluso-axial gap (90 vs. 140 µm, P = 0.026) and the mean occlusal gap (116 vs. 300 µm, P = 0.001) of crowns in Group 1 were significantly smaller compared to the equivalent values in Group 2. Conclusion: Provisional PMMA crowns fabricated by the Asiga printer showed significantly higher marginal and internal adaptation than those manufactured by Digident at all points except for the axial surface.

Diagnostic efficacy of cone-beam computed tomography for detection of vertical root fractures in endodontically treated teeth: a systematic review.

BACKGROUND: Vertical root fractures (VRFs) sometimes occur in endodontically treated teeth. They have a difficult diagnosis and a dismal result. The objective of this review was to evaluate the diagnostic performance of cone-beam computed tomography (CBCT) for detecting VRFs in teeth that had undergone endodontic treatment. METHODS: Literature was reviewed from Web of Science, PubMed, Cochrane Review, SCOPUS, and Embase databases between 2000 and 2022. The searched keywords included "endodontically treated teeth," "cone-beam computed tomography," "CBCT," "tooth fracture," "vertical root fracture," "VRF," "accuracy," "sensitivity," and "specificity." Only articles in the English language were included. The final analysis included 20 papers that satisfied the eligibility requirements. RESULTS: The overall mean ± SD values (%) for the diagnostic sensitivity and specificity of CBCT for detection of VRFs in endodontically treated teeth in the presence of root-filling materials without an intracanal post were 71.50 ± 22.19 and 75.64 ± 19.41, respectively. The overall mean (SD) value (%) for the sensitivity of CBCT for the detection of VRFs in the presence of root-filling materials and intracanal posts was 72.76 (18.73), while the mean (SD) specificity was 75.44 (18.26). The accuracy of CBCT (mean ± SD) was 78.47 ± 17.19% and 74.02 ± 10.64%, respectively, for teeth without intracanal posts and those with posts. CONCLUSIONS: Further clinical research is needed to validate the optimum efficiency of CBCT as a diagnostic technique for detecting VRFs in teeth that have had endodontic treatment, given the low sensitivity, significant heterogeneity of studies, and lack of in-vivo studies on the subject.

Fracture strength and three-dimensional marginal evaluation of biocompatible high-performance polymer versus pressed lithium disilicate crowns.

STATEMENT OF PROBLEM: Despite the acceptable physical properties of biocompatible high-performance polymer (BioHPP), little is known about the marginal accuracy and fracture strength of restorations made from this material. PURPOSE: This in vitro study assessed the marginal and internal adaptation and fracture strength of teeth restored with lithium disilicate (LD) ceramics and BioHPP monolithic crowns. MATERIAL AND METHODS: Twenty-four extracted premolars were prepared for complete coverage crowns and divided into 2 groups to receive pressed IPS e.max LD, or computer-aided design and computer-aided manufacturing (CAD-CAM) BioHPP monolithic crowns. After adhesive cementation, the marginal and internal adaptations of the restorations were evaluated by microcomputed tomography at 18 points for each crown. Specimens were subjected to 6000 thermal cycles at 5 °C and 55 °C and 200 000 load cycles of 100 N at a frequency of 1.2 Hz. The fracture strength of the restorations was then measured in a universal testing machine at a crosshead speed of 0.5 mm/min. Data were analyzed via an independent-sample t-test (α=.05). RESULTS: The mean ±standard deviation of marginal gap was 138.8 ±43.6 µm for LD and 242.1 ±70.7 µm for BioHPP groups (P=.001). The mean ±standard deviation value of absolute marginal discrepancy was 193.8 ±60.8 µm for LD and 263.5 ±97.6 µm for BioHPP groups (P=.06). The internal occlusal and axial gap measurements were 547.5 ±253.1 µm and 197.3 ±54.8 µm for LD (P=.03) and 360 ±62.9 µm and 152.8 ±44.8 µm for BioHPP (P=.04). The mean ±standard deviation of internal space volume was 15.3 ±11.8 µm³ for LD and 24.1 ±10.7 µm³ for BioHPP (P=.08). The mean ±standard deviation of fracture strength was 2509.8 ±680 N for BioHPP and 1090.4 ±454.2 MPa for LD groups (P<.05). CONCLUSIONS: The marginal adaptation of pressed lithium disilicate crowns was better, while BioHPP crowns displayed greater fracture strength. Marginal gap width was not correlated with fracture strength in either group.

Effect of Internal, Office, and Home Bleaching on Shear Bond Strength of Enamel to Porcelain Laminate Veneers

PURPOSE: To compare the effect of office, home, and internal bleaching on the shear bond strength (SBS) of enamel to porcelain laminate veneers. MATERIALS AND METHODS: A total of 36 extracted maxillary central incisors were randomly assigned to four groups: (1) no bleaching (control); (2) office bleaching with 40% hydrogen peroxide (HP); (3) home bleaching with 15% carbamide peroxide; and (4) intracoronal bleaching with sodium perborate (SP) using the walking bleaching technique. All teeth were separately immersed in artificial saliva for 14 days. The enamel surface was then reduced by 0.5 mm, and IPS e.max Press ceramic discs were bonded using a resin cement. After 24 hours, all specimens were thermocycled (5,000 cycles, 5°C to 55°C). The SBS was measured using a universal testing machine, and the failure mode was determined using a stereomicroscope. One-way ANOVA and Tukey honest significant difference tests were used for data analysis (P < .05). RESULTS: A significant difference was noted among the groups (P < .001). The highest SBS was noted in the control group (15.71 ± 5.39 MPa). The mean SBS in the office bleaching group (12.30 ± 4.64 MPa) was almost the same as the control. The lowest mean SBS belonged to the home bleaching group (5.39 ± 3.99 MPa). The mode of failure was adhesive in all four groups. CONCLUSION: If bleaching is intended to be followed by porcelain veneers, the office bleaching technique with 40% HP is recommended. Delaying the bonding procedure for 2 weeks does not appear to be effective with home or intracoronal bleaching.

Knowledge and attitude in implant dentistry training courses amongst undergraduate dental students at Tehran University of Medical Sciences.

INTRODUCTION: Due to the increase of implant treatments in daily practice, graduates should be well acquainted with appropriate diagnostic and therapeutic knowledge in implantology. This study sought to assess the knowledge and attitude of undergraduate students towards the benefits of their courses in the implant dentistry curriculum. MATERIALS AND METHODS: This survey study was performed on all senior dental students at Pardis International Campus, School of Dentistry of Tehran University of Medical Sciences. Data collection was carried out through a questionnaire containing various items on knowledge and attitude. The validity and reliability of the questionnaire were already approved. Collected data were coded, entered in Microsoft Excel 2019, and analysed by t-test (α = .05). RESULTS: Forty questionnaires were filled out by 28 female and 12 male students. Only 7.5% and 12.5% of students reported that they had adequate knowledge to conduct the surgical and prosthetic steps of dental implant treatment, respectively. The majority of students had a positive attitude towards the quality of theoretical education. However, less than 50% of them perceived the same about their practical education. No significant difference existed between male and female students regarding their responses to the knowledge and attitude questions (p = .458 and p = .288, respectively). Ninety percent of the students felt the need for further education regarding dental implant treatment in the undergraduate curriculum. CONCLUSION: Despite the satisfaction of the theoretical knowledge, most senior students believed that they did not achieve adequate expertise to practice after graduation and were willing to receive further practical training in implantology.

Composite Resin Bond Strength to Zirconia and Base Metal Alloys Using Two Types of Intraoral Porcelain Repair Systems.

Objectives: This study aimed to evaluate the shear bond strength (SBS) of two repair composites (Crea.lign vs. PermaFlo) to a base metal alloy and zirconia ceramic. Materials and Methods: Sixty-four discs (12mm diameter, 1mm thickness) were fabricated using Wirobond base metal alloy and zirconia. They were then bonded with their respective composite resins (N=16) in each of the two porcelain chipping repair kit subgroups consisting of PermaFlo and Crea.lign. All specimens were stored in 37°C distilled water for 24 hours. Half of them were subjected to 10,000 thermal cycles (5-55°C, 30s). All specimens were tested for SBS with a universal testing machine. Failure types were analyzed using a digital camera. Analysis of the data was done by two-way ANOVA and Bonferroni post-hoc tests. Results: SBS was significantly affected by the type of composite resin. PermaFlo had a significantly higher SBS than Crea.lign to base metal alloy (P<0.001) and zirconia ceramic (P<0.001). Thermocycling decreased the SBS of both composites to base metal alloy (P<0.001) and zirconia (P<0.001). Conclusion: A universal adhesive could provide higher shear bond strength of zirconia and base metal alloy to composite resin than Crea.lign composite and the MKZ primer supplied by its manufacturer.

Effect of pretreatment with matrix metalloproteinase inhibitors on the durability of bond strength of fiber posts to radicular dentin.

OBJECTIVES: Application of matrix metalloproteinases inhibitors has been suggested to improve the durability of resin-dentin bonding. The purpose of this study was to evaluate the effect of dimethyl sulfoxide (DMSO), carbodiimide (EDC), and chlorhexidine (CHX) treatment on the push-out bond strength of fiber posts to radicular dentin. MATERIALS AND METHODS: 24 extracted premolars were assigned randomly to 4 groups after root canal treatment and post space preparation (n = 6). In the first, second, and third groups, radicular dentin was treated with 1 ml of 5% DMSO, 0.3 M EDC, and 2% CHX, respectively. The fourth group (control) received no treatment. The root canals were primed with ED primer II, and the fiber posts were cemented with Panavia F2.0. In each group, half of the specimens were subjected to the push-out test and the other half to 3000 thermal cycles before testing. Data were analyzed using two-way analysis of variance via SPSS version 20 (p < .05). RESULTS: Among the nonthermocycled specimens, the values of push-out bond strength were observed in the control, EDC, CHX, and DMSO groups, in decreasing order. Among the thermocycled specimens, the values were observed in the control, EDC, DMSO, and CHX groups in decreasing order. Thermocycling had a significant adverse effect on the push-out bond strength (p = .015), but the effect of material (p = .375), and the interaction effect of material and thermocycling (p = .998) were not significant. CONCLUSIONS: Application of CHX, DMSO, and EDC had no significant effect on the bond strength of fiber posts to radicular dentin.

Antifungal Efficacy of a Permanent Silicon Soft Liner Containing Silver Nanoparticles.

Objectives: This study aimed to evaluate the in vitro antifungal efficacy of addition of silver nanoparticles (SNPs) to Mucopren® silicone soft liner material. Materials and Methods: Twenty disc samples (8 × 2 mm) of Mucopren® silicone soft liner containing 0wt% (control), 0.5wt%, 1wt%, 2wt%, and 3wt% SNPs were fabricated. Samples were powdered and added to 150 mL of Sabouraud dextrose agar culture medium and placed on separate culture dish plates. Each plate was inoculated with 106 colony forming units per milliliter (CFUs/mL) of Candida albicans (PTCC 5027) according to the CLSI protocol, and incubated at 37℃. The colony count was verified at 24 h, and the antifungal effect of the samples was evaluated according to the percentage of viable cells in the 2 subgroups with/without thermocycling. Data were analyzed using SPSS version 20 via ANOVA and t-test (P<0.05). Results: All experimental groups showed higher antifungal activity than the control group, and this effect was dose-dependent (P<0.05). The lowest colony count was recorded in the 3wt% group. Thermocycling had no significant effect on the antifungal efficacy, except in 0.5wt% concentration of SNPs (P=0.013). Conclusion: Addition of SNPs to Mucopren soft liner conferred antifungal effects. Further mechanical stability and toxicity studies are still required.

Resistance to demineralisation of adjacent enamel and dentine, fluoride release and dentine bond strength of fluoride-containing self-etch adhesive systems.

BACKGROUND: The current study aimed to assess the amount of fluoride released from fluoride-containing dental adhesives and its effect on micro-tensile bond strength (µTBS) and on resistance to demineralisation of dentine and enamel. MATERIAL AND METHODS: Two fluoride-containing dental adhesives, and a fluoride-free adhesive were used as experimental adhesives. After thermal cycling the µ-TBS of adhesives to dentine and the failure mode were assessed. The fluoride release and cross-sectional microhardness (CSMH) of specimens were measured before and after one day, 7 and 28 days of pH-cycling. The data were analysed using one-way ANOVA, Weibull statistics and repeated measures ANOVA. RESULTS: The results indicated a significant difference between the group of FL and both the SE and LBF groups (p≤0.001). The CSMH values of both the dentine and enamel underneath the adhesives was reduced at 28 th day of the pH-cycling compared to the baseline (p≤0.001). From day 1 to day 28, the released fluoride declined in both the fluoride containing dental adhesives (p≤0.001). CONCLUSIONS: Based on the results, the released fluoride from dental adhesives may adversely influence the bond strength and durability of the resin/dentine interface. Moreover, the released fluoride didn't improve the resistance to demineralisation of adjacent enamel and dentine to bond interface. Key words:Fluoride release, micro-tensile bond strength, microhardness, fluoride-containing adhesives.

Effect of Incorporation of Silver Nanoparticles on the Tensile Bond Strength of a Long term Soft Denture Liner.

OBJECTIVES: This study aimed at assessing the effect of the addition of silver nanoparticles (SNPs) to a silicone soft liner on its tensile bond strength to denture base resin. MATERIALS AND METHODS: SNPs were added to Mucopren cold cure soft liner in 0 (control), 0.5, 1, 2, and 3 wt% concentrations and bonded in 120 stainless steel molds with processed heat cure acrylic resin blocks. Liner/resin combination samples were divided into two groups. The first half was stored for 2 days in distilled water at 37°C and then subjected to tensile bond strength, while the other half were thermocycled 3000 times before testing. Mean bond strength, expressed in mega pascals (MPa), was determined in the tensile test with the use of a universal testing machine at a crosshead speed of 5 mm/min. STATISTICAL ANALYSIS: Data were analyzed using SPSS via one-way analysis of variance test, t-test, and Tukey's posthoc, at a 95% confidence level (p < 0.05). RESULTS: Addition of SNPs and thermocycling both caused a significant reduction in the tensile bond strength of Mucopren to acrylic resin; however, in the thermocycled group, the bond strength increased with the increase in the concentration of SNPs (p < 0.001). CONCLUSION: Addition of SNPs to Mucopren soft silicone liner reduces its tensile bond strength to denture acrylic resin.

Efficacy of Low-Level Laser, Hard Occlusal Appliance and Conventional Pharmacotherapy in the Management of Myofascial Pain Dysfunction Syndrome; A Preliminary Study.

Introduction: Myofascial pain dysfunction syndrome (MPDS) is a common temporomandibular joint disorder. Due to its multifactorial etiology, treatment usually involves more than one modality to obtain complementary results. The purpose of this study was to compare the combined effect of a low-level laser, a hard occlusal appliance, and conventional pharmacotherapy with pharmacotherapy only in the management of patients with MPDS. Methods: In this study, 15 patients with MPDS were diagnosed and randomly assigned to 3 groups (n=5). Subjects in Group 1 were treated with pharmacotherapy (PT); Group 2 received the diode laser (940 nm gallium arsenide) every other day for a total of 10 sessions, plus pharmacotherapy (PTL) and Group 3 were given hard occlusal splint 12 h/day for 4 weeks, plus pharmacotherapy (PTO). The intensity of pain was measured using the visual analog scale (VAS) prior to the treatment, 2 and 4 weeks after the onset of treatment and 2 weeks later. The maximum painless mouth opening and pain intensity at muscle palpation were also recorded. Comparisons were made between the groups via repeated measure analysis of variance (ANOVA) (P<0.05). Results: Pain relief in the subjective VAS was observed in both laser and appliance groups in the third and fourth examination sessions (P<0.05). No statistically significant reduction in pain was noted using pharmacotherapy only. The maximum painless mouth opening and muscle tenderness were not significantly different between the 3 groups (P>0.05). Conclusion: Both the laser and the occlusal appliance combined with pharmacotherapy proved to be effective for pain reduction in patients with MPDS. All groups, however, failed to result in a significant improvement in the maximum mouth opening or tenderness in masticatory muscles.

Relationship between Parafunctional Habits and Salivary Biomarkers.

OBJECTIVES: Parafunctional habits, as one of the etiological factors of temporomandibular disorders (TMD), are an individual's response to increased stress. During stress and depression, biomarkers such as cortisol and salivary alpha-amylase (SAA) are secreted in the saliva. The present study aimed to investigate whether there is a correlation between salivary stress biomarkers and parafunctional habits. MATERIALS AND METHODS: Thirty-two cases, from May to September 2015, were selected based on two standard stress questionnaires, namely the depression anxiety stress Scale-21 (DASS-21) and the Beck Anxiety Inventory (BAI). Saliva samples were collected to examine the level of unstimulated salivary cortisol and SAA. The significance of the results was assessed via student's t-test and Mann-Whitney test (α=0.05). RESULTS: The mean concentrations of cortisol and SAA in unstimulated saliva were significantly higher in the case group than in the control group (P=0.01 and 0.44, respectively). The mean scores of anxiety, stress, and depression were significantly higher in the case group than in the control group (P<0.05). CONCLUSION: It seems that the levels of salivary cortisol and SAA, as well as stress, anxiety, and depression scores, are higher in patients with parafunctional habits.

Fracture Strength of Endodontically treated Maxillary Central Incisors restored with Nickel Chromium and Nonprecious Gold Alloy Casting Post and Cores.

AIM: Since fiber posts are not recommended for teeth under lateral loads, a new alloy containing >80% copper (nonprecious gold or NPG) was introduced with a modulus of elasticity closer to that of dentin and easier preparation. This study aimed to compare the fracture strength of endodontically treated maxillary central incisors restored with nickel chromium (Ni-Cr) and NPG alloys. MATERIALS AND METHODS: Casting post and cores were fabricated of Ni-Cr and NPG alloys for 24 maxillary central incisors (n = 12). Full-metal crowns were also fabricated and placed under cyclin loading in 30 N load and 45° angle, for 250,000 cycles with 2.6 Hz frequency. The fracture strength was measured at a crosshead speed of 0.5 mm/min and 135° angle in a universal testing machine. Data were analyzed using independent t-test. RESULTS: The mean fracture strength was 731.179 ± 327.47 and 1411.89 ± 313.56 N in the Ni-Cr and NPG groups respectively; this difference was statistically significant (p < 0.001). The fracture was irreparable in all teeth since the fracture line was below the cementoenamel junction (CEJ). CONCLUSION: The fracture strength of teeth restored with cast NPG post and cores was significantly higher than that of teeth restored with cast Ni-Cr post and cores. CLINICAL SIGNIFICANCE: Due to proper mechanical properties, NPG post and cores seem to be a suitable choice for restoration of severely damaged anterior teeth, provided that other properties are proven to be acceptable.

Stress Distribution in Splinted and Unsplinted Implant-Supported Maxillary Overdentures: A 3D Finite Element Analysis.

INTRODUCTION: This study was accomplished to assess the biomechanical state of splinting in implant-supported maxillary overdentures. MATERIALS AND METHODS: Two models of maxillary overdentures were designed in SolidWorks 2011. The first model included 4 separate implants and ball abutments, whereas the second one included 4 splinted implants connected with a bar. Evaluation was performed in ANSYS Workbench software with 200 N load applied at the molar-premolar region, bilaterally. The maximum equivalent stress and strain (von Mises) was recorded and analyzed along a path between the implants in the crestal bone and the prosthetic attachments. RESULTS: First model presented higher values of strain in prosthetic attachment and higher values of von Mises stress in crestal bone. The second model presented higher stress concentration in the gingival tissue of premolar area (near the bar), whereas the peak stress values were reported within the most distal part of the soft tissue support of the prosthesis in the first model (unsplinted). CONCLUSION: Splinting maxillary overdentures implants is associated with significant lower stress levels in the surrounding bone tissue.

Effect of cement type and thickness on push-out bond strength of fiber posts.

Background. This study investigated the effect of the thickness of two resin cements on push-out bond strength of fiber posts to root dentin. Methods. Sixty decoronated single-rooted teeth were endodontically treated. The specimens were then randomly allocated to two groups (n=30); group 1: drill size 90 w, matching the size of fiber posts used; group 2: drill size 110, larger than the posts. The specimens in each group were divided into 2 subgroups (n=15); subgroup SE, in which the posts were cemented with self-etch Panavia F2.0 and subgroup SA, in which self-adhesive Panavia cement was used. After 72 hours, 2 slices with 1 mm of thickness were prepared from the mid-root of each specimen. Push-out bond strength test was performed in a universal testing machine at a crosshead speed of 1 mm/min. Data were analyzed with two-way ANOVA and t-test. Results. The mean bond strengths of the posts cemented in matched-size spaces for SE and SA groups were 4.02±1.6 and 4.12±2.3 MPa, respectively. For posts cemented in oversized spaces, the values were 4.9±2.3 and 2.8±1.3 MPa, respectively. In matched-size spaces, there was no significant difference between the two groups. Conclusion. The results of this study suggested that increasing the cement thickness would reduce the bond strength of fiber posts to root dentin when self-adhesive cements are used; however, self-etch adhesives were not affected.

Fracture resistances of zirconia, cast Ni-Cr, and fiber-glass composite posts under all-ceramic crowns in endodontically treated premolars.

PURPOSE: The aim of the present study was to evaluate the fracture resistances of zirconia, cast nickel-chromium alloy (Ni-Cr), and fiber-composite post systems under all-ceramic crowns in endodontically treated mandibular first premolars. MATERIALS AND METHODS: A total of 36 extracted human mandibular premolars were selected, subjected to standard endodontic treatment, and divided into three groups (n=12) as follows: cast Ni-Cr post-and-core, one-piece custom-milled zirconia post-and-core, and prefabricated fiber-glass post with composite resin core. Each specimen had an all-ceramic crown with zirconia coping and was then loaded to failure using a universal testing machine at a cross-head speed of 0.5 mm/min, at an angle of 45 degrees to the long axis of the roots. Fracture resistance and modes of failure were analyzed. The significance of the results was assessed using analysis of variance (ANOVA) and Tukey honest significance difference (HSD) tests (α=.05). RESULTS: Fiber-glass posts with composite cores showed the highest fracture resistance values (915.70±323 N), and the zirconia post system showed the lowest resistance (435.34±220 N). The corresponding mean value for the Ni-Cr casting post and cores was reported as 780.59±270 N. The differences among the groups were statistically significant (P<.05) for the zirconia group, as tested by ANOVA and Tukey HSD tests. CONCLUSION: The fracture resistance of zirconia post-and-core systems was found to be significantly lower than those of fiberglass and cast Ni-Cr post systems. Moreover, catastrophic and non-restorable fractures were more prevalent in teeth restored by zirconia posts.

Effect of Storage Time and Temperature on Dimensional Stability of Impressions Made with Zinc Oxide Impression Paste.

OBJECTIVES: This study aimed to assess the effect of storage time and temperature on dimensional stability of impressions made with Cavex Outline zinc oxide impression paste. MATERIALS AND METHODS: A round stainless steel mold with five grooves (three horizontal and two vertical) was used in this in-vitro experimental study. Cavex Outline impression paste was prepared according to the manufacturer's instructions and applied to the mold. The mold was placed on a block and stored at 35°C and 100% humidity for setting. The impressions were poured with stone immediately and also after 30, 120, 240 and 420 minutes and 24 hours. The distance between the vertical lines on the casts was measured and compared with that in the immediately poured cast. RESULTS: Storage in a refrigerator and at room temperature for zero to seven hours had no significant effect on dimensional stability of the impressions; however, 24 hours of storage in a refrigerator or at room temperature decreased the dimensional stability of Cavex Outline (P=0.001). Also, a significant association was found between dimensional changes following 24 hours of storage in a refrigerator (4°C) and at room temperature (23°C; P<0.01). CONCLUSIONS: The optimal pouring time of Cavex Outline impressions with stone is between zero to seven hours, and 24 hours of storage significantly decreases the dimensional stability.

Biomechanical effects of platform switching in two different implant systems: a three-dimensional finite element analysis.

OBJECTIVES: The purpose of this study was to determine the influence of platform switching on stress distribution of two different implant systems using three-dimensional (3D) finite element models. MATERIALS AND METHODS: Six 3D finite element models were created to replicate two different implant systems with peri-implant bone tissue, in which six different implant-abutment configurations were represented: model XiVE-a: 3.8-mm-diameter implant and 3.8-mm-diameter abutment; model XiVE-b (platform-switching model): 4.5-mm-diameter implant and 3.8-mm-diameter abutment; model XiVE-c: 4.5-mm-diameter implant and 4.5-mm-diameter abutment; model 3i-a: 4.0-mm-diameter implant and 4.1-mm-diameter abutment; model 3i-b (platform-switching model): 5.0-mm-diameter implant and 4.1-mm-diameter abutment; model 3i-c: 5.0-mm-diameter implant and 5.0-mm-diameter abutment. vertical and oblique loads of 100 were applied to all models. RESULTS: While the pattern of stress distribution was similar for both loading situations, oblique loading resulted in higher intensity and greater distribution of stress than axial loading in both cortical bone and implant-abutment- interface. Stress distribution at peri-implant bone was almost identical with similar magnitudes for all six models. In both implant systems, platform-switching models demonstrated lower maximum von Mises stress in cortical bone than conventional models. However, in both implant systems and under both loading situations, platform-switching models showed higher stresses at the implant-abutment interface than conventional models. CONCLUSION: In both implant systems, platform switching design reduced the stress concentration in the crestal bone and shifted it towards the area of implant-abutment interface.