RESUMO
Introduction: Occipitocervical fusion is performed to address craniocervical and atlantoaxial instability. A screw of at least 8mm is needed for biomechanical stability. Occipital thickness of Malay ethnicity is unknown, and this study presents the optimal screw placement positions for occiput screw in this population. This was a retrospective cross-sectional study of 100 Malays who underwent computed tomography (CT) scan for brain assessment. To measure the occipital bone thickness of Malay ethnicity at the area of common screw placement for occipitocervical fusion. The subject's data was obtained from the institutional database with consent from the administrations and the patients. None of the patients had any head and neck pathology. Materials and methods: The subject's data was obtained from the institutional database with consent from the administrations and the patients. None of the patients had any head and neck pathology. Computed tomography (CT) of 100 Malay patients who underwent head and neck CT were analysed, based on our inclusion and exclusion criteria. Measurements were taken using a specialised viewer software where 55 points were measured, followed a grid with 10mm distance using external occipital protuberance (EOP) as the reference point. Results: There were 57 males and 43 females of Malay ethnicity with a mean age of 36.7 years analysed in this study. The EOP was the thickest bone of the occiput which measured 16.15mm. There was an area of at least 8mm thickness up to 20mm on either side of the EOP, and at level 10mm inferior to the EOP. There is thickness of at least 8mm, up to 30mm inferior to the EOP at the midline. The males have significantly thicker bone especially along the midline compared to females. Conclusion: Screws of at least 8mm can be safely inserted in the Malay population at 20mm on either side of the EOP at the level 10mm inferior to the EOP and up to 30mm inferior to the EOP at the midline.
RESUMO
Various methods have been developed for rapid and high throughput full genome sequencing of SARS-CoV-2. Here, we described a protocol for targeted multiplex full genome sequencing of SARS-CoV-2 genomic RNA directly extracted from human nasopharyngeal swabs using the Ion Personal Genome Machine (PGM). This protocol involves concomitant amplification of 237 gene fragments encompassing the SARS-CoV-2 genome to increase the abundance and yield of viral specific sequencing reads. Five complete and one near-complete genome sequences of SARS-CoV-2 were generated with a single Ion PGM sequencing run. The sequence coverage analysis revealed two amplicons (positions 13 751-13 965 and 23 941-24 106), which consistently gave low sequencing read coverage in all isolates except 4Apr20-64- Hu. We analyzed the potential primer binding sites within these low covered regions and noted that the 4Apr20-64-Hu possess C at positions 13 730 and 23 929, whereas the other isolates possess T at these positions. The genome nucleotide variations observed suggest that the naturally occurring variations present in the actively circulating SARS-CoV-2 strains affected the performance of the target enrichment panel of the Ion AmpliSeq™ SARS CoV 2 Research Panel. The possible impact of other genome nucleotide variations warrants further investigation, and an improved version of the Ion AmpliSeq™ SARS CoV 2 Research Panel, hence, should be considered.
Assuntos
Genoma Viral , Sequenciamento de Nucleotídeos em Larga Escala , Reação em Cadeia da Polimerase Multiplex , SARS-CoV-2/genética , Sequenciamento Completo do Genoma , Sequência de Bases , COVID-19 , Sequenciamento de Nucleotídeos em Larga Escala/métodos , Humanos , Reação em Cadeia da Polimerase Multiplex/métodos , Sequenciamento Completo do Genoma/métodosRESUMO
Biopolymers and their applications have been widely studied in recent years. Replacing the oil based polymer materials with biopolymers in a sustainable manner might give not only a competitive advantage but, in addition, they possess unique properties which cannot be emulated by conventional polymers. This review covers the fabrication of porous materials from natural biopolymers (cellulose, chitosan, collagen), synthetic biopolymers (poly(lactic acid), poly(lactic-co-glycolic acid)) and their composite materials. Properties of biopolymers strongly depend on the polymer structure and are of great importance when fabricating the polymer into intended applications. Biopolymers find a large spectrum of application in the medical field. Other fields such as packaging, technical, environmental, agricultural and food are also gaining importance. The introduction of porosity into a biomaterial broadens the scope of applications. There are many techniques used to fabricate porous polymers. Fabrication methods, including the basic and conventional techniques to the more recent ones, are reviewed. Advantages and limitations of each method are discussed in detail. Special emphasis is placed on the pore characteristics of biomaterials used for various applications. This review can aid in furthering our understanding of the fabrication methods and about controlling the porosity and microarchitecture of porous biopolymer materials.
RESUMO
Members of the genus Kocuria are commonly found in the environment and they are also commensals of the mammalian skin and oropharynx mucosa. Human infections, although rare, are increasingly being reported recently suggesting that this genus has mostly been overlooked or misidentified. Its transmission route however, is still not known. We report here the isolation and identification of a Kocuria marina isolate from the lung of a wild urban rat (Rattus rattus diardii) caught at a wet market. The isolate was susceptible to most of the commonly used antibiotics. The finding suggests a possibility that rats could be a vector for K. marina.