DESIGN OF MEDICAL RADIOMETER FRONT-END FOR IMPROVED PERFORMANCE.

We have investigated the possibility of building a singleband Dicke radiometer that is inexpensive, small-sized, stable, highly sensitive, and which consists of readily available microwave components. The selected frequency band is at 3.25-3.75 GHz which provides a reasonable compromise between spatial resolution (antenna size) and sensing depth for radiometry applications in lossy tissue. Foreseen applications of the instrument are non-invasive temperature monitoring for breast cancer detection and temperature monitoring during heating. We have found off-the-shelf microwave components that are sufficiently small (< 5 mm × 5 mm) and which offer satisfactory overall sensitivity. Two different Dicke radiometers have been realized: one is a conventional design with the Dicke switch at the front-end to select either the antenna or noise reference channels for amplification. The second design places a matched pair of low noise amplifiers in front of the Dicke switch to reduce system noise figure.Numerical simulations were performed to test the design concepts before building prototype PCB front-end layouts of the radiometer. Both designs provide an overall power gain of approximately 50 dB over a 500 MHz bandwidth centered at 3.5 GHz. No stability problems were observed despite using triple-cascaded amplifier configurations to boost the thermal signals. The prototypes were tested for sensitivity after calibration in two different water baths. Experiments showed superior sensitivity (36% higher) when implementing the low noise amplifier before the Dicke switch (close to the antenna) compared to the other design with the Dicke switch in front. Radiometer performance was also tested in a multilayered phantom during alternating heating and radiometric reading. Empirical tests showed that for the configuration with Dicke switch first, the switch had to be locked in the reference position during application of microwave heating to avoid damage to the active components (amplifiers and power meter). For the configuration with a low noise amplifier up front, damage would occur to the active components of the radiometer if used in presence of the microwave heating antenna. Nevertheless, this design showed significantly improved sensitivity of measured temperatures and merits further investigation to determine methods of protecting the radiometer for amplifier first front ends.

Non-invasive vesicoureteral reflux detection: heating risk studies for a new device.

OBJECTIVE: To investigate a novel non-invasive device developed to warm bladder urine and to measure kidney temperature to detect vesicoureteral reflux. MATERIALS AND METHODS: Microwave antennas focused energy within the bladder. Phantom experiments measured the results. The heating protocol was optimized in an in-vivo porcine model, and then tested once, twice and three times consecutively in three pigs followed by pathologic examinations. RESULTS: Computer simulations showed a dual concentric conductor square slot antenna to be the best. Phantom studies revealed that this antenna easily heated a bladder phantom without over heating intervening layers. In-vivo a bladder heating protocol of 3 min with 30 W each to two adjacent antennas 45 s on 15 s off followed by 15 min of 15 s on and 45 s off was sufficient. When pigs were heated once, twice and three times with this heating protocol, pathologic examination of all tissues in the heated area showed no thermal changes. More intensive heating in the animal may have resulted in damage to muscle fibers in the anterior abdominal wall. CONCLUSIONS: Selective warming of bladder urine was successfully demonstrated in phantom and animals. Localized heating for this novel vesicoureteral reflux device requires low-power levels and should be safe for humans.

Design of Small-sized and Low-cost Front End to Medical Microwave Radiometer.

We have investigated the possibility of building a Dicke radiometer that is inexpensive, small-sized, stable, high sensitivity and consists of readily available microwave components. The selected frequency band is at 3-4 GHz and can be used for breast cancer detection, with sufficient spatial resolution. We have found microwave components that are small (< 5mm × 5 mm) and provide sufficient sensitivity. We have built two different Dicke radiometers: One is of conventional design with Dicke switch at front end to select antenna or noise rererence and the other with a low noise amplifier before the Dicke Switch. We have tested this concept with simulations and built prototypes. The two designs provide a gain of approximately 50 dB, and bandwidth of about 500 MHz. One of the designs has a stability µ > 1 and the other design provide instability µ < 1 for a part of the pass band. The prototypes are tested for sensitivity after calibration in two different known temperature waterbaths. The results show that the design with the low noise amplifier before the Dicke switch has 36% higher sensitivity than the other design with Dicke switch in front.