Microplastic co-exposure elevates cadmium accumulation in mouse tissue after rice consumption: Mechanisms and health implications.

Rice cadmium (Cd) and microplastics are prevalent contaminants, posing a co-exposure threat to humans by means of dietary intake. To assess whether co-exposure of microplastics affects the bioavailability of rice Cd, mice were exposed to Cd-contaminated rice with microplastic co-exposure. We found that polyethylene (PE), polystyrene (PS), polypropylene (PP), and polyamide (PA) microplastic co-exposure via diet consumption (2 µg g-1) caused 1.17-1.38-fold higher Cd accumulation in tissue of mice fed by Cd-rice. For mice with co-exposure of PE microplastics, the higher rice-Cd bioavailability corresponded to colonization of Lactobacillus reuteri (38.9 % vs 17.5 %) in the gut compared to control mice, which caused higher production of gut metabolites particularly peptides, likely causing a 'side effect' of elevating Cd solubility in the intestinal lumen. In addition, abundance of sphingosine 1-phosphate in the gut of mice was reduced under PE microplastic exposure, which may reduce intracellular calcium ions (Ca2+) in enterocytes and form a weaker competition in pumping of intracellular Ca2+ and Cd2+ across the basolateral membrane of enterocytes, leading to higher Cd2+ transport efficiency. The results suggest elevated Cd exposure risk from rice consumption with microplastic co-exposure at environmentally relevant low concentrations.

Association of preserved ratio impaired spirometry with mortality and cardiovascular diseases: a systematic review and meta-analysis.

BACKGROUND: Preserved ratio impaired spirometry (PRISm) is a type of abnormal lung function. PRISm and mortality have been explored in several studies, but a comprehensive evaluation of the associations is limited. The current study aims to conduct a systematic review and meta-analysis in order to investigate the mortality and cardiovascular diseases in patients with PRISm. METHODS: PubMed, Embase, and Web of Science databases, as well as gray literature sources, were searched for relevant studies published up to 7 September 2023 without language restrictions. This review included all published observational cohort studies that investigated the association of PRISm with mortality in the general population, as well as subgroup analyses in smokers and pre-bronchodilation spirometry studies. The outcomes of interest were all-cause mortality, cardiovascular mortality, and respiratory-related mortality. The Newcastle-Ottawa scale assessed study quality. Sensitivity and subgroup analyses explored heterogeneity and robustness. Publication bias was assessed with Egger's and Begg's tests. RESULTS: Overall, eight studies were included in this meta-analysis. The pooled HR was 1.60 (95% CI, 1.48-1.74) for all-cause mortality, 1.68 (95% CI, 1.46-1.94) for CVD mortality, and 3.09 (95% CI, 1.42-6.71) for respiratory-related mortality in PRISm group compared to normal group. In the subgroup analysis, participants with PRISm had a higher effect (HR, 2.11; 95% CI, 1.74-2.54) on all-cause mortality among smokers relative to participants with normal spirometry. Furthermore, the association between PRISm and mortality risk was consistent across several sensitivity analyses. CONCLUSIONS: People with PRISm were associated with an increased risk of all-cause mortality, CVD mortality, and respiratory-related mortality as compared to those with normal lung function in the general population. SYSTEMATIC REVIEW REGISTRATION: PROSPERO CRD42023426872.

Influence of Polypropylene Fiber on Concrete Permeability under Freeze-Thaw Conditions and Mechanical Loading.

Polypropylene fiber reinforcement is an effective method to enhance the durability of concrete structures. With the increasing public interest in the widespread use of polypropylene fiber reinforced concrete (PFRC), the necessity of evaluating the mechanism of polypropylene fiber (PF) on the permeability of concrete has become prominent. This paper describes the influence of PF on the concrete permeability exposed to freeze-thaw cycles under compressive and tensile stress. The permeability of PFRC under compressive and tensile loads is accurately measured by a specialized permeability setup. The permeability of PFRC under compressive and tensile loads, the volume change of PFRC under compressive load, and the relationship between compressive stress levels at minimum permeability and minimum volume points of PFRC are discussed. The results indicate that the addition of PF adversely affects the permeability of concrete without freeze-thaw damage and cracks. However, it decreases the permeability of concrete specimens exposed to freeze-thaw cycles and cracking. Under compressive load, the permeability of PFRC initially decreases slowly and follows by a significant increase as the compressive stress level increases. This phenomenon correlates with the volume change of the specimen. The compressive stress level of the minimum permeability point and compressive stress level of the minimum volume point of PFRC exhibit a linear correlation, with a fitted proportional function parameter γ ≈ 0.98872. Under tensile load, the permeability of PFRC increases gradually with radial deformation and follows by a significant increase. The strain-permeability curves of PFRC under loading are studied and consist of two stages. In stage I, the permeability of PFRC gradually decreases with the increase of strain under compressive load, while the permeability increases with the increase of strain under tensile load. In stage II, under compressive load, the permeability of PFRC increases with the increase of freeze-thaw cycles, whereas under tensile load, the permeability gradually decreases with the increase of freeze-thaw cycles. The reduction of PF on the permeability of PFRC under tensile load is greater than that under compressive load. In future research, the relationship between strain and permeability of PFRC can be integrated with its constitutive relationship between stress and strain to provide a reference for the application of PF in the waterproofing of concrete structures.

Effects of Fe(III) on the formation and toxicity alteration of halonitromethanes, dichloroacetonitrile, and dichloroacetamide from polyethyleneimine during UV/chlorine disinfection.

Trace iron ions (Fe(III)) are commonly found in water and wastewater, where free chlorine is very likely to coexist with Fe(III) affecting the disinfectant's stability and N-DBPs' fate during UV/chlorine disinfection, and yet current understanding of these mechanisms is limited. This study investigates the effects of Fe(III) on the formation and toxicity alteration of halonitromethanes (HNMs), dichloroacetonitrile (DCAN), and dichloroacetamide (DCAcAm) from polyethyleneimine (PEI) during UV/chlorine disinfection. Results reveal that the maxima concentrations of HNMs, DCAN, and DCAcAm during UV/chlorine disinfection with additional Fe(III) were 1.39, 1.38, and 1.29 times higher than those without additional Fe(III), instead of being similar to those of Fe(III) inhibited the formation of HNMs, DCAN and DCAcAm during chlorination disinfection. Meanwhile, higher Fe(III) concentration, acidic pH, and higher chlorine dose were more favorable for forming HNMs, DCAN, and DCAcAm during UV/chlorine disinfection, which were highly dependent on the involvement of HO· and Cl·. Fe(III) in the aquatic environment partially hydrolyzed to the photoactive Fe(III)­hydroxyl complexes Fe(OH)2+ and [Fe(H2O)6]3+, which undergone UV photoactivation and coupling reactions with HOCl to achieve effective Fe(III)/Fe(II) interconversion, a process that facilitated the sustainable production of HO·. Extensive product analysis and comparison verified that the HO· production enhanced by the Fe(III)/Fe(II) internal cycle played a primary role in increasing HNMs, DCAN, and DCAcAm productions during UV/chlorine disinfection. Note that the incorporation of Fe(III) increased the cytotoxicity and genotoxicity of HNMs, DCAN, and DCAcAm formed during UV/chlorine disinfection, and yet Fe(III) did not have a significant effect on the acute toxicity of water samples before, during, and after UV/chlorine disinfection. The new findings broaden the knowledge of Fe(III) affecting HNMs, DCAN, and DCAcAm formation and toxicity alteration during UV/chlorine disinfection.

Lithium Plating Characteristics in High Areal Capacity Li-Ion Battery Electrodes.

Li-ion battery degradation and safety events are often attributed to undesirable metallic lithium plating. Since their release, Li-ion battery electrodes have been made progressively thicker to provide a higher energy density. However, the propensity for plating in these thicker pairings is not well understood. Herein, we combine an experimental plating-prone condition with robust mesoscale modeling to examine electrode pairings with capacities ranging from 2.5 to 6 mAh/cm2 and negative to positive (N/P) electrode areal capacity ratio from 0.9 to 1.8 without the need for extensive aging tests. Using both experimentation and a mesoscale model, we identify a shift from conventional high state-of-charge (SOC) type plating to high overpotential (OP) type plating as electrode thickness increases. These two plating modes have distinct morphologies, identified by optical microscopy and electrochemical signatures. We demonstrate that under operating conditions where these plating modes converge, a high propensity of plating exists, revealing the importance of predicting and avoiding this overlap for a given electrode pairing. Further, we identify that thicker electrodes, beyond a capacity of 3 mAh/cm2 or thickness >75 µm, are prone to high OP, limiting negative electrode (NE) utilization and preventing cross-sectional oversizing the NE from mitigating plating. Here, it simply contributes to added mass and volume. The experimental thermal gradient and mesoscale model either combined or independently provide techniques capable of probing performance and safety implications of mild changes to electrode design features.

Characteristic substance analysis and rapid detection of bacteria spores in cooked meat products by surface enhanced Raman scattering based on Ag@AuNP array substrate.

BACKGROUND: Bacterial spores are the main potential hazard in medium- and high-temperature sterilized meat products, and their germination and subsequent reproduction and metabolism can lead to food spoilage. Moreover, the spores of some species pose a health and safety threat to consumers. The rapid detection, prevention, and control of bacterial spores has always been a scientific problem and a major challenge for the medium and high-temperature meat industry. Early and sensitive identification of spores in meat products is a decisive factor in contributing to consumer health and safety. RESULTS: In this study, we developed a novel and stable Ag@AuNP array substrate by using a two-step synthesis approach and a liquid-interface self-assembly method that can directly detect bacterial spores in actual meat product samples without the need for additional in vitro bacterial culture. The results indicate that the Ag@AuNP array substrate exhibits high reproducibility and Raman enhancement effects (1.35 × 105). The differentiation in the Surface enhanced Raman scattering (SERS) spectra of five bacterial spores primarily arises from proteins in the spore coat and inner membrane, peptidoglycan of cortex, and Ca2⁺-DPA within the spore core. The correct recognition rate of linear discriminant analysis for spores in the meat product matrix can reach 100 %. The average recovery accuracy of the SERS quantitative model was at around 101.77 %, and the limit of detection can reach below 10 CFU/mL. SIGNIFICANCE: It provides a promising technological strategy for the characteristic substance analysis and timely monitoring of spores in meat products.

A pollen selection system links self and interspecific incompatibility in the Brassicaceae.

Self-incompatibility and recurrent transitions to self-compatibility have shaped the extant mating systems underlying the nonrandom mating critical for speciation in angiosperms. Linkage between self-incompatibility and speciation is illustrated by the shared pollen rejection pathway between self-incompatibility and interspecific unilateral incompatibility (UI) in the Brassicaceae. However, the pollen discrimination system that activates this shared pathway for heterospecific pollen rejection remains unknown. Here we show that Stigma UI3.1, the genetically identified stigma determinant of UI in Arabidopsis lyrata × Arabidopsis arenosa crosses, encodes the S-locus-related glycoprotein 1 (SLR1). Heterologous expression of A. lyrata or Capsella grandiflora SLR1 confers on some Arabidopsis thaliana accessions the ability to discriminate against heterospecific pollen. Acquisition of this ability also requires a functional S-locus receptor kinase (SRK), whose ligand-induced dimerization activates the self-pollen rejection pathway in the stigma. SLR1 interacts with SRK and interferes with SRK homomer formation. We propose a pollen discrimination system based on competition between basal or ligand-induced SLR1-SRK and SRK-SRK complex formation. The resulting SRK homomer levels would be sensed by the common pollen rejection pathway, allowing discrimination among conspecific self- and cross-pollen as well as heterospecific pollen. Our results establish a mechanistic link at the pollen recognition phase between self-incompatibility and interspecific incompatibility.

Understanding physical exercise among individuals with substance use disorders using an integrated theoretical perspective of the health action process approach and theory of planned behavior.

Introduction: Physical exercise is considered a useful non-pharmacological adjunctive treatment for promoting recovery from substance use disorders (SUD). However, adherence to physical exercise treatments is low, and little is known about what factors are associated with the initiation and maintenance of physical exercise behaviors. The aim of this study was to explore the psychosocial factors underlying these behaviors in individuals with SUD using an integrated theoretical model based on the health action process approach (HAPA) and the theory of planned behavior (TPB). Methods: A total of 1,197 individuals with SUDs (aged 37.20 ± 8.62 years) were recruited from 10 compulsory isolation drug rehabilitation centers in Zhejiang Province via convenience sampling according to a set of inclusion criteria. Self-reported data were collected to assess task self-efficacy (TSE), maintenance self-efficacy (MSE), recovery self-efficacy (RSE), outcome expectations (OE), action planning (AP), coping planning (CP), social support (SS), subjective norms (SN), attitude behavior (AB), behavioral intention (BI), perceived behavioral control (PBC), risk perception (RP), exercise stage, and exercise behavior in this integrated model. ANOVA and structural equation modeling (SEM) were used to evaluate this model. Results: One-way ANOVA revealed that the majority of the moderating variables were significantly different in the exercise phase. Further SEM showed that the model fit the data and revealed several important relationships. TSE, RP, SS, AB, and SN were indirectly associated with physical exercise behavior in individuals with SUD through the BI in the SUD initiation stage. In addition, PBC was directly related to physical exercise behavior in individuals with SUD. In the maintenance stage, MSE, AP, CP and exercise behavior were significantly related. Moreover, AP and CP were mediators of BI and MSE. Conclusion: This study is the first attempt to integrate patterns of physical exercise behavior in individuals with SUD. The HAPA-TPB integration model provides a useful framework for identifying determinants of physical exercise behavioral intentions and behaviors in individuals with SUD and for explaining and predicting the initiation and maintenance of physical exercise behaviors in these individuals. Moreover, the model provides scientific guidance for the enhancement of physical exercise adherence in individuals with SUD.

Effect of Macro Fibers on the Permeability and Crack Surface Topography of Layered Fiber Reinforced Concrete.

This paper describes the effects of macro fibers on permeability and crack surface topography of layered fiber-reinforced concrete (FRC) specimens with different layering ratios under uniaxial tensile load. The crack permeability of layered FRC specimens is investigated by a self-designed permeability setup. The topographical analysis of crack surfaces is investigated by a custom-designed laser scanning setup. The results show that when the fiber volume content and layering ratio of the FRC layer are constant, the tensile toughness of layered FRC specimens depends on the proportion of steel fiber in macro fibers, and with an increase in the proportion of steel fiber, the tensile toughness of layered FRC specimens increases. For the layered FRC specimens, the crack permeability is much lower than that of the normal concrete (NC) specimen. A significant positive synergistic effect on crack impermeability can be achieved by the combination of steel fiber and polypropylene fiber in the SF80PP2.3 specimen. The crack surface roughness parameter (Rn) values of the NC layer in layered FRC specimens are all higher than those of the NC specimen, and the crack surface Rn of the FRC layer in layered FRC specimens is higher than that of the unlayered FRC specimens. This can effectively increase the head loss of cracks and reduce the crack permeability of layered FRC specimens.

Hybrid Fiber Influence on the Crack Permeability of Cracked Concrete Exposed to Freeze-Thaw Cycles.

This paper describes hybrid fiber's influence on the crack permeability of cracked concrete exposed to freeze-thaw cycles. A permeability setup and a laser-scanning setup have been designed to measure the crack permeability and the fractured surface roughness of cracked hybrid fiber-reinforced concrete, containing polypropylene fiber and steel fiber, under a splitting tensile load. The results show that, when the effective crack width of the specimens is less than 25 µm, the rough crack surface significantly reduces the concrete's crack permeability. As the crack width increases, the effect of the concrete crack surface on crack permeability gradually decreases, and the crack permeability of the concrete is closer to the Poiseuille flow model. The permeability parameter α derived from the Poiseuille flow model is effective for assessing the crack permeability of concrete. Compared to the modified factor ξ of crack permeability, the permeability parameter α can effectively evaluate and quantify the development trend of crack permeability within a certain range of crack widths. The permeability parameter α of SF20PP2.3, subjected to the same freeze-thaw cycles, decreases by 16.3-94.8% compared to PP4.6 and SF40, and SF20PP2.3 demonstrates a positive synergistic effect on the crack impermeability of cracked concrete. The crack impermeability of SF40PP2.3, subjected to the same freeze-thaw cycles, lies between that of PP6.9 and SF60. The roughness of crack surface (X) and the crack permeability (Y) are highly correlated and follow an exponential curve (Y = 1.0415 × 107·e-6.025·X) in concrete. This demonstrates that hybrid fibers enhance crack impermeability by increasing the crack surface roughness. Furthermore, the combination of polypropylene fiber and steel fiber effectively promotes the formation of micro-cracks and facilitates the propagation of multiple cracks in the concrete matrix. This combination increases the head loss of water flow through the concrete and decreases the crack permeability.

FDM 3D Printing and Properties of PBAT/PLA Blends.

Biodegradable polylactic acid (PLA) has been widely used in fused deposition modeling (FDM) 3D printing. In order to improve its comprehensive properties in 3D printing, in this study, 0-40% content of polybutylene adipate terephthalate(PBAT) was selected to be blended with PLA in a twin-screw extruder; the resulting pellets were drawn into a homogeneous filament; then, PBAT/PLA samples were prepared by FDM 3D printing, and the effects of the dosage of PBAT on the mechanical properties, thermal behavior, surface wettability and melt flowability of the samples were investigated. The results showed that all the samples could be printed smoothly, and the ductility was slightly improved by the increase in the PBAT dosage; the thermal stability of PLA was enhanced by blending with PBAT, and the crystallinity increased monotonically with the increase in PBAT. After blending with PBAT, the surfaces of the samples were more hydrophilic and flowable. The important conclusion achieved in this work was that the PBAT/PLA blends, especially those containing 30%PBAT, showed great potential to replace petroleum-based plastics and are suitable for use in FDM 3D printing technologies for different applications.

Associations of perceived built environment characteristics using NEWS questionnaires with all-cause mortality and major cardiovascular diseases: The prospective urban rural epidemiology (PURE)-China study.

BACKGROUND: Despite increased literature focusing on the role of the built environment (BE) in health, few cohort studies have quantitatively analyzed neighborhood walkability environment in relation to the risk of death and cardiovascular disease (CVD). This longitudinal study aimed at evaluating the association between perceived BE attributeswith mortality and major CVD based on the Prospective Urban Rural Epidemiology study in China (PURE-China). METHODS: The PURE-China study recruited 47,931 participants aged 35-70 years from 12 provinces of China between 2005 and 2009. The perceived BE information, including land use, street, aesthetics, and safety, was collected using the neighborhood environment walkability scale (NEWS) questionnaire, with higher scores indicating a more favorable rating. Two primary outcomes are all-cause mortality and major CVD event. The Cox frailty model with random intercepts was used to assess the association between the perceived total BE/subscales score and outcomes. RESULTS: Of 32,163 participants included in this study, 19,253 (59.9 %) were women, and the mean (SD) age was 51.0 (9.5) years. After a median follow-up period of 11.7 years (IQR 9.4 - 12.2), we observed that one standard deviation higher of combined BE scores was related to a lower risk of all-cause mortality (HR = 0.85; 95 %CI, 0.80-0.90), and major CVD events (HR = 0.95; 95 %CI, 0.90-0.99). The subscales of perceived BE were related to a lower risk, although a few were not significant. Land use mix-diversity and safety from crime were the two most significant subscales. Stronger risks were observed among urban and female participants. CONCLUSION: Favorable perceived BE characteristics were linked with a lower risk of all-cause mortality and major CVD events in Chinese population, especially in urban areas and females. Our findings can be used by policymakers to take action to mitigate the adverse effect of poor community conditions on health, such as improving local amenities and transport connectivity, providing building paths for walking, running and cycling.

The distribution of the depth of aortic dissection and the correlation of the dissection depth index with other parameters.

BACKGROUND: In patients with aortic dissection, the aortic wall is separated into two layers along a dissection plane. In this study, a survey was performed to investigate the distribution of the depth of dissection plane and its correlation with other clinical and pathological parameters to help understand and expand the current knowledge of aortic dissection. METHODS: Pathology information system were searched for patients with aortic dissection who had undergone aortic replacement between 2019 and 2022 in Wuhan Asia General Hospital. The depth of dissection plane and dissection depth index were measured in the area around the edge of dissection plane. Correlation between parameters was calculated using Spearman's rank correlation coefficient. RESULTS: 124 patients were included in this study. The depth of dissection plane ranged from 533 to 2335 microns, and the 5th percentile was 778 microns. The dissection depth index ranged from 0.320 to 0.972, and the 5th percentile was 0.503. The correlation coefficients were -0.305 (P=.0007), -0.259 (P=0.0111), 0.188 (P=0.0367), 0.189 (P=0.0359) respectively for male gender, the length of aortic dissection, atherosclerosis, and translamellar mucoid extracellular matrix accumulation. CONCLUSIONS: In 95% of patients with aortic dissection, the depth of dissection plane is larger than 778 microns, and the dissection depth index is greater than 0.503. In other words, aortic dissection rarely occurs in the inner 50.3% of the aortic media. The dissection depth index is negatively correlated with male gender and the length of aortic dissection, and positively correlated with atherosclerosis and translamellar mucoid extracellular matrix accumulation.

Quantitative analysis of the relationship between the myocardial bridge and the FAI of pericoronal fat on computed tomography.

We performed this cohort study to investigate whether the myocardial bridge (MB) affects the fat attenuation index (FAI) and to determine the optimal cardiac phase to measure the volume and the FAI of pericoronary adipose tissue (PCAT). The data of 300 patients who were diagnosed with MB of the left anterior descending (LAD) coronary artery were retrospectively analyzed. All of patients were divided into the MB group and the MB with atherosclerosis group. In addition, 104 patients with negative CCTA results were enrolled as the control group. There was no significant difference between FAI values measured in systole and diastole (P > 0.05). There was no significant difference in FAI among the MB group, the MB with atherosclerosis group, and the control group (P > 0.05). In MB with atherosclerosis group, LAD stenosis degree (< 50%) (OR = 0.186, 95% CI 0.036-0.960; P = 0.045) and MB located in the distal part of LAD opening (OR = 0.880, 95% CI 0.789-0.980; P = 0.020) were protective factors of FAI value. A distance (from the LAD opening to the proximal point of the MB) of 29.85 mm had the highest predictive value for abnormal FAI [area under the curve (AUC), 0.798], with a sensitivity of 81.1% and a specificity of 74.6%.

The Effects of Different Doses of Sufentanil on Intraoperative Cardiovascular Response and Postoperative Recovery in Patients Undergoing Cardiac Surgery: A Retrospective Cohort Study.

Objective: To investigate the correlation between the amount of sufentanil used during anesthesia and intraoperative hemodynamic fluctuation and postoperative recovery in patients undergoing cardiopulmonary bypass (CPB). Materials and Methods: A retrospective analysis was performed on 454 patients undergoing elective heart surgery under CPB. Patients were divided into two groups according to the amount of sufentanil used during anesthesia: Group L (induced sufentanil 0.4-0.6 ug /kg, maintained sufentanil 0.01-0.02 ug/kg/min, n = 223) and Group H (induced sufentanil 4-6 ug/kg, maintained sufentanil 0.02-0.03 ug/kg/min, n = 231). Propensity score matching (PSM) was used at a 1:1 nearest-neighbor ratio to compare the two groups. Intraoperative use of vasoactive drugs, spontaneous heart rebound, secondary endotracheal intubation, postoperative mechanical ventilation time, the length of stay (LOS) in ICU, postoperative LOS in hospital, postoperative in-hospital mortality were analyzed. Results: After matching, a total of 144 patients were included (72 patients in Group L, and 72 patients in Group H). Multivariate logistic regression analysis showed that the dosage of sufentanil during anesthesia was significantly correlated with the utilization rate of intraoperative vasoactive drugs (P < 0.001) and the success rate of spontaneous heart rebound (p = 0.001). The utilization rate of vasoactive drugs decreased significantly in Group H (OR, 0.062; 95% CI, 0.019-0.200) compared to that of Group L. The success rate of spontaneous heart rebound (OR, 0.187; 95% CI, 0.071-0.491) was higher in Group H. There were no differences on postoperative recovery outcomes between the two groups. Conclusion: On the basis of our data, the use of high-dose sufentanil is beneficial to keep the cardiovascular response of patients in a stable state, but there is no significant effect on the quality of early postoperative recovery.

Efficacy and safety of epidural block with lidocaine for refractory severe plaque psoriasis: An open-label pilot study in real world setting.

Epidural block using lidocaine, a non-selective blocker of voltage-gated sodium channels (Nav), has demonstrated efficacy in the treatment of severe plaque psoriasis in a limited number of cases. This study aimed to evaluate the effectiveness and safety of epidural lidocaine block in adult patients with severe, treatment-resistant plaque psoriasis. This was an open-label pilot study. Patients with severe plaque-type psoriasis unresponsive to at least one systemic treatment were enrolled for a 1-week epidural lidocaine block and followed up for 48 weeks. Thirty-six patients participated, with 32 completing the study. At the 12-week mark, there was a remarkable 59% improvement in the mean Psoriasis Area Severity Index (PASI) score (P < 0.001). By week 48, 28 out of 32 patients (87%) achieved PASI 75, while 18 out of 32 (56%) reached PASI 90. Within 7 days, 20 out of 21 patients (95%) reported a reduction in itch, with a mean itch reduction of 82% at day 1 and 94% at day 7. Notably, no severe side effects were observed. Epidural lidocaine block proved to be an effective and safe long-term treatment option for individuals with refractory severe plaque psoriasis.

Quantitative computed tomography angiography evaluation of the coronary fractional flow reserve in patients with left anterior descending artery myocardial bridging.

PURPOSE: To quantitatively investigate the effect of myocardial bridge (MB) in the left anterior descending artery (LAD) on the fractional flow reserve (FFR). MATERIALS AND METHODS: Three-hundred patients with LAD MB who had undergone coronary artery CT angiography (CCTA) were retrospectively enroled, and 104 normal patients were enroled as the control. The CCTA-derived fractional flow reserve (FFRCT) was measured at the LAD 10 mm proximal (FFR1) and 20-40 mm distal (FFR3) to the MB and at the MB location (FFR2). RESULTS: FFR2 and FFR3 of the MB (with BM only) and MBLA (with both MB and atherosclerosis) groups were significantly (p < 0.01) lower than those of the control. The FFR3 distal to the MB was significantly lower (p < 0.01) than that of the control. The FFRCT of the whole LAD in the MBLA group was significantly (p < 0.05) lower than that of the MB and control group (p < 0.05). MB length (OR 1.061) and MB muscle index (odds ratio or OR 1.007) were two risk factors for abnormal FFRCT, and MB length was a significant independent risk factor for abnormal FFRCT (OR = 1.077). LAD stenosis degree was a risk factor for abnormal FFRCT values (OR 3.301, 95% confidence interval [CI] 1.441-7.562, p = 0.005) and was also a significant independent risk factor (OR = 3.369, 95% CI: 1.392-8.152; p = 0.007) for abnormal FFRCT. CONCLUSION: MB significantly affects the FFRCT of distal coronary artery. For patients with MB without atherosclerosis, the MB length is a risk factor significantly affecting FFRCT, and for patients with MB accompanied by atherosclerosis, LAD stenotic severity is an independent risk factor for FFRCT.

Wearable biosensors for human sweat glucose detection based on carbon black nanoparticles.

Wearable glucose biosensors enable noninvasive glucose monitoring, thereby enhancing blood glucose management. In this work, we present a wearable biosensor based on carbon black nanoparticles (CBNPs) for glucose detection in human sweat. The biosensor consists of CBNPs, Prussian blue (PB), glucose oxidase, chitosan, and Nafion. The fabricated biosensor has a linear range of 5 µM to 1250 µM, sensitivity of 14.64 µA mM-1 cm-2, and a low detection potential (-0.05 V, vs. Ag/AgCl). The detection limit for glucose was calculated as 4.83 µM. This reusable biosensor has good selectivity and stability and exhibits a good response to glucose in real sweat. These results demonstrate the potential of our CBNP-based biosensor for monitoring blood glucose in human sweat.

Selective purification and rapid quantitative detection of spores using a "stepped" magnetic flow device.

A study on the inactivation and germination mechanism of spores is very important in the application of spores, as such high-purity spores are the basis of related research. However, spores and vegetative cells of bacteria often coexist, and it is difficult to separate them. In this study, a magnetic flow device for the purification of spores in the culture medium system was developed based on a "stepped" structure with a magnetic force that could absorb vegetative cells with magnetic nanoparticles. The operation process was as follows: first, vancomycin functionalized nanoparticles were used to prepare Van-Fe3O4 NPs, which were then combined with vegetative cells to form a magnetic conjugate. Subsequently, the magnetic conjugate (vegetative cells) flowed through the "stepped" magnetic flow device and was adsorbed. Meanwhile, the spores moved through the channel and were collected. The achieved purity of the collected spores was more than 95%. Further, the number of the obtained spores was quickly quantified using Raman spectroscopy. The entire purification and quantitative process can be completed within 30 min and the limit of detection was 5 CFU mL-1. This study showed outstanding spore purification ability and provided a new method for purification and rapid quantitative detection of spores.

A retrospective analysis of the effect of latent tuberculosis infection on clinical pregnancy outcomes of in vitro fertilization-fresh embryo transferred in infertile women.

In areas with high incidence of tuberculosis (TB), there are more infertile women who underwent in vitro fertilization (IVF) and have latent TB infection (LTBI), and thus, their potential risks should be paid enough attention. The purpose of our study aimed to analyze the relationship between LTBI and clinical pregnancy outcomes of IVF and fresh embryo transfer (IVF-FET). This was a retrospective study of 628 infertile women who had undergone IVF-FET in the Fourth Affiliated Hospital of Hebei Medical University from January 2019 to December 2021. The women experienced no clinical symptoms, negative imaging, and T-SPOT.TB-positive diagnosis of LTBI. We divided the study population into the LTBI group and the non-LTBI group. The clinical pregnancy rate in the LTBI group was significantly lower than that in the non-LTBI group (40.54% vs 49.51%, P = 0.031), and there was no significant difference in live birth rate and miscarriage rate between the two groups. Logistic regression analysis showed that LTBI was an independent risk factor for decreased clinical pregnancy rate in infertile women undergoing IVF-FET. In conclusion, LTBI affects clinical pregnancy rate of IVF-FET in infertile women, and therefore, clinicians (especially in countries with a high TB burden) need to pay attention to LTBI before IVF and embryo transfer.