Effect of Vibration Pretreatment-Microwave Curing Process Parameters on the Mechanical Performance of Resin-Based Composites.

The vibration pretreatment-microwave curing process can achieve high-quality molding under low-pressure conditions and is widely used in the curing of resin-based composites. This study investigated the effects of the vibration pretreatment process parameters on the void content and the fiber weight fraction of T700/TRE231; specifically, their influence on the interlaminar shear strength and impact strength of the composite. Initially, an orthogonal experimental design was employed with interlaminar shear strength as the optimization target, where vibration acceleration was determined as the primary factor and dwell time as the secondary factor. Concurrently, thermogravimetric analysis (TGA) was performed based on process parameters that corresponded to the extremum of interlaminar shear strength, revealing a 2.17% difference in fiber weight fraction among specimens with varying parameters, indicating a minimal effect of fiber weight fraction on mechanical properties. Optical digital microscope (ODM) analysis identified interlaminar large-size voids in specimens treated with vibration energy of 5 g and 15 g, while specimens subjected to a vibration energy of 10 g exhibited numerous small-sized voids within layers, suggesting that vibration acceleration influences void escape pathways. Finally, impact testing revealed the effect of the vibration pretreatment process parameters on the impact strength, implying a positive correlation between interlaminar shear strength and impact strength.

Aramid Honeycomb Cores under Constant Pressure: Unveiling the Out-of-Plane Compression Deformation.

The primary challenge during the secondary bonding process of full-height honeycomb sandwich structures is the aramid honeycomb core's height shrinkage. This paper systematically investigated the height evolution behavior of the honeycomb core by using a creep testing machine. The results showed that the out-of-plane compression deformation curve of aramid honeycomb cores is mainly divided into three stages: the dehumidification stage, the pressurization stage and the creep stage. Under conditions of high temperature and pressure, height shrinkage was attributed to the dehydration caused by moisture infiltration, and the compression creep resulted from the slippage of polymer molecular chains. Dehydration shrinkage is stable, whereas compression creep reflects typical viscoelastic polymer characteristics. By employing the viscoelastic Burgers mechanical model and applying the nonlinear surface fitting method, the total height shrinkage deformation behavior of the aramid honeycomb core during the curing process can be accurately predicted by summing the above three stages. This research contributes valuable insights for the manufacturing process of honeycomb sandwich structures.

Effects of Curing Defects in Adhesive Layers on Carbon Fiber-Quartz Fiber Bonded Joint Performance.

Due to their mechanical load-bearing and functional wave transmission, adhesively bonded joints of carbon fiber-quartz fiber composites have been widely used in the new generation of stealth aviation equipment. However, the curing defects, caused by deviations between the process environment and the setting parameters, directly affect the service performance of the joint during the curing cycle. Therefore, the thermophysical parameter evolution of adhesive films was analyzed via dynamic DSC (differential scanning calorimeter), isothermal DSC and TGA (thermal gravimetric analyzer) tests. The various prefabricating defects within the adhesive layer were used to systematically simulate the impacts of void defects on the tensile properties, and orthogonal tests were designed to clarify the effects of the curing process parameters on the joints' bonding performance. The results demonstrate that the J-116 B adhesive film starts to cure at a temperature of 160 °C and gradually forms a three-dimensional mesh-bearing structure. Furthermore, a bonding interface between the J-116 B adhesive film and the components to be connected is generated. When the curing temperature exceeds 200 °C, both the adhesive film and the resin matrix thermally degrade the molecular structure. The adhesive strength weakens with an increasing defect area ratio and number, remaining more sensitive to triangle, edge and penetration defects. By affecting the molecular structure of the adhesive film, the curing temperature has a significant impact on the bonding properties; when the curing degree is ensured, the curing pressure directly impacts the adhesive's performance by influencing the morphology, number and distribution of voids. Conversely, the heating rate and heat preservation time have minimal effects on the bonding performance.

Metal-Metal Bonding Process Research Based on Xgboost Machine Learning Algorithm.

Conventionally, the optimization of bonding process parameters requires multi-parameter repetitive experiments, the processing of data, and the characterization of complex relationships between process parameters, and performance must be achieved with the help of new technologies. This work focused on improving metal-metal bonding performance by applying SLJ experiments, finite element models (FEMs), and the Xgboost machine learning (ML) algorithm. The importance ranking of process parameters on tensile-shear strength (TSS) was evaluated with the interpretation toolkit SHAP (Shapley additive explanations) and it optimized reasonable bonding process parameters. The validity of the FEM was verified using SLJ experiments. The Xgboost models with 70 runs can achieve better prediction results. According to the degree of influence, the process parameters affecting the TSS ranked from high to low are roughness, adhesive layer thickness, and lap length, and the corresponding optimized values were 0.89 µm, 0.1 mm, and 27 mm, respectively. The experimentally measured TSS values increased by 14% from the optimized process parameters via the Xgboost model. ML methods provide a more accurate and intuitive understanding of process parameters on TSS.

Simulation and Experimental Study on the Internal Leak Behavior in Carbon Fiber Reinforced Composite Components.

In this paper, the diffusion law of helium gas inside composite materials was obtained through numerical research and an experimental approach. The influence of fiber and the fiber-resin interface on permeability was discussed in the actual numerical model. It was found that the leak rate and the mass concentration at the fiber-resin interface were higher than those in the resin, and the leak rate symmetrically distributed along the horizontal central line. Meanwhile, a homogenized model for the leak rate simulation in carbon fiber composite components was established, and its accuracy was verified through the experiment and the actual numerical model. The simulated result and the test data demonstrated that the leak rate increased with the pressure and decreased with the thickness of the specimen.

Optimization of Vibration Pretreatment Microwave Curing in Composite Laminate Molding Process.

Vibration pretreatment microwave curing is a high-quality and efficient composite out-of-autoclave molding process. Focusing on interlaminar shear strength, the effects of pretreatment temperature, pretreatment time and vibration acceleration on the molding performance of composite components were analyzed sequentially using the orthogonal test design method; a scanning electron microscope (SEM) and optical digital microscope (ODM) were used to analyze the void content and fiber-resin bonding state of the specimens under different curing and molding processes. The results show that the influence order of the different vibration process parameters on the molding quality of the components was: vibration acceleration > pretreatment temperature > pretreatment time. Within the parameters analyzed in this study, the optimal vibration pretreatment process parameters were: pretreatment temperature of 90 °C, pretreatment time of 30 min, and vibration acceleration of 10 g. Using these parameters, the interlaminar shear strength of the component was 82.12 MPa and the void content was 0.37%. Compared with the microwave curing process, the void content decreased by 71.8%, and the interlaminar shear strength increased by 31.6%. The microscopic morphology and mechanical properties basically reached the same level as the standard autoclave process, which achieved a high-quality out-of-autoclave curing and molding manufacturing of aerospace composite components.

Weighted multilinear hardy operators on Herz type spaces.

This paper focuses on the bounds of weighted multilinear Hardy operators on the product Herz spaces and the product Morrey-Herz spaces, respectively. We present a sufficient condition on the weight function that guarantees weighted multilinear Hardy operators to be bounded on the product Herz spaces. And the condition is necessary under certain assumptions. Finally, we extend the obtained results to the product Morrey-Herz spaces.

Correlation of AIM2 expression in peripheral blood mononuclear cells from humans with acute and chronic hepatitis B.

The AIM2 (absent in melanoma 2) protein promotes host defenses against invading viruses and pathogenic bacteria through corresponding adapter molecules leading to the initiation of innate immune responses. We investigated the expression of AIM2 in peripheral blood mononuclear cells (PBMCs) from patients with acute hepatitis B (AHB) and chronic hepatitis B (CHB) during different clinical phases, and analyzed the correlation between AIM2 and clinical profiles in these groups. This study indicated that there is higher expression of AIM2, IL-1ß, and IL-18 in AHB compared with expression in CHB. The expression of AIM2 mRNA was significantly negatively correlated with serum hepatitis B virus (HBV) load, HBeAg, and significantly positively correlated with IL-1ß and IL-18 in AHB patients and CHB patients with immune clearance, which suggests that AIM2 expression is correlated with the immune clearance of HBV in the host. We summarized that there is a higher immune status in AHB, and a lower immune response in CHB. This suggests that the down-regulation of AIM2 may be associated with the chronic development of HB.

Age versus clinical virological characteristics in chronic hepatitis B virus infection: a case series study in China.

OBJECTIVES: This study aimed to investigate the clinical virological characteristics of hepatitis B virus (HBV) in chronic HBV infection patients of different ages, especially in relapse patients and patients with immune clearance. METHODS: The HBV clinical virological characteristics of chronic HBV infection were investigated in 1572 Chinese patients of different age groups (<20, 20-40, and >40 years old). RESULTS: Of the patients in the below 20 age group, those with evidence of immune tolerance accounted for 86.05% (P<0.001). Of the patients in the 20-40 age group, those with immune clearance accounted for 36.36% (P<0.001). Of the patients in the above 40 age group, there were markedly more reactivation cases than in any other group (P<0.001). Our data indicated that a positive correlation (r=0.480, P<0.001) existed between HBV DNA contents (on a log10 scale) and the alanine aminotransferase (ALT) level of the total cases with reactivation. Of the 300 cases with immune clearance being followed up 10-50 months after enrollment, 181 cases achieved spontaneous hepatitis B e antigen (HBeAg) seroconversion (HBeAg to anti-HBe), and the younger the patient, the shorter the time to seroconversion (P<0.05). CONCLUSION: Generally, there were significantly different HBV clinical virological characteristics in patients with chronic HBV infection of different ages. Different features were observed in relapse patients and patients with immune clearance at different ages, and these two types of patients needed antiretroviral therapy. Our study suggests that revisions of the timing and elevated alanine aminotransferase standards for chronic hepatitis B antiretroviral therapy in Chinese relapse patients and patients with immune clearance in different age groups are warranted.