Electrochemical and computational evaluation of hydrazide derivative for mild steel corrosion inhibition and anticancer study.

In the present study the authors' main goal is to avoid the corrosive attack of the chloride ions of 3.5% NaCl solution in saline medium on the mild steel (MS), by addition of small amount of a new derivative of the hydrazide called ligand (HL), as a corrosion inhibitor. This study had been achieved by employing different electrochemical measurements such as, open circuit potential (OCP), electrochemical impedance spectroscopy (EIS) and potentio-dynamic polarization (PDP) methods. The results of the electrochemical test (OCP), showed that, the open circuit potential of the mild steel in saline solution, was guided to more positive direction in presence of the ligand (HL), at its ideal concentration (1 × 10-3 M), compared to the (OCP), of the mild steel in absence of (HL). The results of the electrochemical methods, EIS and PDP presented that, the ligand (HL), was acted as a good corrosion inhibitor for hindering the corrosion process of the mild steel in 3.5% sodium chloride, as it was recorded a good percentage of the inhibition efficiency (77.45%, 53.41%, by EIS and PDP techniques respectively), at its optimum concentration (1 × 10-3 M). Also, the corrosion rate of the mild steel in the saline medium without (HL), was listed about (0.0017 mm/year), while in existence of (HL), was decreased to a value about (0.00061 mm/year). As well, some of electrical properties of (HL), and its derivative [Pd(II), Cr(III), and Ru(III)], complexes were investigated such as; the activation energy (Ea(ac)), which recorded values in the range of 0.02-0.44 (eV) range and electrical conductivity which listed values at room temperature in the range of 10-5-10-8 S.cm-1. The results of the AC and DC electrical conductivity measurements for (HL), and its derivative [Pd(II), Cr(III) and Ru(III)] complexes indicate semiconducting nature which suggests that these compounds could be used in electronic devices. Also, the complexes exhibited higher conductivity values than (HL). Photophysical studies showed good florescence properties of HL that indicated that it can be used to determine most of the drugs with no fluorescence properties by quenching and calculating quantum yield. Moreover, the hydrazide ligand (HL), has shown selectivity as an active anticancer candidate drug for both breast and colon cancer in humans. Density function theory demonstrated that, the frontier molecular orbital HOMOs of the complexes have exhibited similar behavior and the charge density has localized in the metallic region of all the studied complexes. Also, the values of the energy gap of the ligand (HL), and its complexes Pd(II), Cr(III) and Ru(III), had been arranged in this order HL > Cr(III) > Ru(III) > Pd(II). All characterization using different spectroscopic techniques were reported to elucidate the proposed structures such as; thermal analysis, elemental analysis of C, H, and N atoms, spectral analysis using IR, UV, 1H NMR techniques, scanning electron microscopy and energy dispersive X-ray analyses.

Study of microstructure and corrosion behavior of nano-Al2O3 coating layers on TiO2 substrate via polymeric method and microwave combustion.

The study describes the successful development of a TiO2 ceramic substrate with a protective nano-Al2O3 coating using two different coating techniques: microwave combustion and polymeric methods. The coated ceramics demonstrate enhanced corrosion resistance compared to the uncoated substrate. The optimal TiO2 substrate was prepared by firing it at 1000 °C. This was done to give the desired physical properties of the TiO2 substrate for the coating procedures. Nano-Al2O3 powder was coated onto the surface of the TiO2 substrates. The TiO2 substrates with the Al2O3 coating were then calcined (heat-treated) at 800 and 1000 °C. The structures, morphology, phase composition, apparent porosity, bulk density, and compressive strength of the substrate and coated substrate were characterized. Upon firing at 1000 °C, it was discovered that the two phases of TiO2-rutile and anatase-combine in the substrate. Once the substrate has been coated with nano Al2O3 at 1000 °C, the anatase is transferred into rutile. When compared to the substrate, the coated substrate resulted in a decrease in porosity and an increase in strength. The efficiency of the ceramic metal nanoparticles Al2O3 as a good coating material to protect the TiO2 substrates against the effect of the corrosive medium 0.5 M solution of H2SO4 was measured by two methods: potentio-dynamic polarization (PDP) and the electrochemical impedance spectroscopy (EIS). The results indicated that the corrosion rate was decreased after the substrate coated with alumina from (67.71 to 16.30 C.R. mm/year) and the percentage of the inhibition efficiency recorded a high value reaching (78.56%). The surface morphology and composition after electrochemical measurements are investigated using SEM and EDX analysis. After conducting the corrosion tests and all the characterization, the results indicated that the coated TiO2 substrate prepared by the polymeric method at 800 °C displayed the best physical, mechanical, and corrosion-resistant behavior.

Facile synthesis of copper nitroprusside chitosan nanocomposite and its catalytic reduction of environmentally hazardous azodyes.

One of the biggest issues affecting the entire world currently is water contamination caused by textile industries' incapacity to properly dispose their wastewater. The presence of toxic textile dyes in the aquatic environment has attracted significant research interest due to their high environmental stability and their negative effects on human health and ecosystems. Therefore, it is crucial to convert the hazardous dyes such as methyl orange (MO) azo dye into environmentally safe products. In this context, we describe the use of Copper Nitroprusside Chitosan (Cu/SNP/Cts) nanocomposite as a nanocatalyst for the chemical reduction of azodyes by sodium borohydride (NaBH4). The Cu/SNP/Cts was readily obtained by chemical coprecipitation in a stoichiometric manner. The X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and Fourier transform infrared (FT-IR) spectroscopy were applied to investigate chemical, phase, composition, and molecular interactions. Additionally, Scanning electron microscope (SEM) was used to examine the nanomaterial's microstructure. UV-vis spectroscopy was utilized for studying the Cu Nitroprusside Chitosan's catalytic activity for the reduction of azodye. The Cu/SNP/Cts nanocomposite demonstrated outstanding performance with total reduction time 160 s and pseudo-first order constant of 0.0188 s-1. Additionally, the stability and reusability study demonstrated exceptional reusability up to 5 cycles with minimal activity loss. The developed Cu/SNP/Cts nanocomposite act as efficient nanocatalysts for the reduction of harmful Methyl orange azodye.