Synthesis and Characterization of Enhanced Photocatalytic Activity with Li+-Doping Nanosized TiO2 Catalyst.

The photocatalytic efficiency of TiO2 is reduced by rapid electron-hole recombination. An effective approach to address this limitation is to have TiO2 doped with various metal ions or heteroatoms. Herein, we prepared a series of Li+-doped TiO2 nanoparticles showing high photocatalytic activities through the sol-gel method. The samples were characterized by X-ray diffraction (XRD) and surface area analyses. Effects of Li+ doping on the Brunauer-Emmett-Teller (BET) surface area, crystallite size, phase transformation temperature, and phase composition were studied. The results showed that Li+ doping can promote the generation of the rutile crystal phase in TiO2, lower the anatase-to-rutile transformation temperature, and generate the mixed-crystal effect. The photocatalytic degradation of methyl orange (MO) was used as a probe reaction to evaluate the photoactivity of the nanoparticles. Parameters affecting the photocatalytic efficiency, including the Li+ doping amount, calcination temperature, and catalyst amount, as well as the kinetics of the photocatalytic process toward the degradation of MO, were investigated. The mixed-crystal TiO2, which was doped with 1.0 mol % Li+ and calcined at 550 °C containing 27.1% rutile and 72.9% anatase phase, showed a 2.2-fold increase in the photoactivity on the basis of the rate constant of MO decomposition as compared with the undoped TiO2. The existence of a definite quantity of rutile phase could effectively inhibit the recombination of the electron-hole pairs, thus promoting photocatalytic activity.

Aggregation-Induced Electrochemiluminescence of the Dichlorobis(1,10-phenanthroline)ruthenium(II) (Ru(phen)2Cl2)/Tri-n-propylamine (TPrA) System in H2O-MeCN Mixtures for Identification of Nucleic Acids.

Aggregation-induced electrochemiluminescence (AIECL) of the dichlorobis(1,10-phenanthroline)ruthenium(II) (Ru(phen)2Cl2)/tri-n-propylamine (TPrA) system was systematically investigated in H2O-MeCN media. Up to a 120-fold increase in the ECL intensity was observed when the H2O fraction (v%) was changed from 30% to 70%, whereas only an approximately 5.7-fold increase in the corresponding aggregation-induced fluorescence emission was demonstrated. The gradual formation of clusters of Ru(phen)2Cl2 nanoaggregates along with the increase in the H2O fraction to MeCN, which was verified by dynamic light scattering (DLS), scanning electron microscopy (SEM), and transmission electron microscopy (TEM), was believed to be responsible for the remarkable ECL enhancement. Significantly, the above-mentioned AIECL behavior was found to be very sensitive to the types and sequences of nucleic acids present in solution, which provided an effective and novel strategy for distinguishing RNA from DNA and for differentiating different miRNAs. The present study could have a substantial impact in various research areas, such as molecular sensors, bioimaging probes, organelle-specific imaging, and tumor diagnosis.

Ultrasensitive detection of miRNA based on efficient immobilization of probe and electrochemiluminescent quenching of Ru(bpy)32+ by methylene blue.

A high performance miRNA biosensor based on effective click chemistry assembly of a Ru(bpy)32+ labeled DNA probe and efficient electrochemiluminescence (ECL) quenching of the Ru(bpy)32+/BDEA (BDEA = N-butyldiethanolamine) system by surface-confined electroactive methylene blue (MB) dye is reported. When the target miRNA was present, the ECL signal instantly changed from "light off" to "light on" status. Using the specific miRNA let-7d as the target analyte, this biosensor provided sensitive detection over approximately six orders of magnitude (10 fM-10 nM), with a limit of detection of 10 fM (S/N = 3). Detailed study of the ECL quenching behavior of the Ru(bpy)32+/BDEA system by MB in solution suggested that the ECL quenching involves a combination of photoluminescence dynamic quenching and quenching processes directly associated with the redox reactions, as well as resonance energy transfer. A large binding constant of 4.7 × 1011 M-1 between let-7d and the DNA hairpin was estimated using an ECL-based extended Langmuir isotherm model, suggesting remarkably strong binding of the target to the probe. Furthermore, our biosensor exhibited excellent specificity and reproducibility. Using the developed system, the concentration of the target miRNA extracted from the A549 cell line could be obtained, demonstrating the potential application of the developed biosensor to practical biological sample analysis.

Electrogenerated Chemiluminescence Biosensor with a Tripod Probe for the Highly Sensitive Detection of MicroRNA.

A novel probe for the highly sensitive detection of microRNA with enhanced helix accessibility and good assembling without backfilling was developed using a tripod structure fabricated by triplex DNA. A layer of triplex DNA assembled on electrodeposited reduced graphene oxide was used as the capture probe, and a subsequent hybridization chain reaction that promoted the efficient intercalation of the electrogenerated chemiluminescence (ECL) emitter [Ru(bpy)2(dppz)]2+ (bpy refers to 2,2'-bipyridine, and dppz refers to dipyrido[3,2- a:2',3'- c]phenazine) was used as an analytical-signal amplifier. The fabricated biosensor was examined with an anodic ECL mode using tri- n-propyl amine as the coreactant. The construction of the biosensor was systematically characterized with various techniques including atomic-force microscopy, gel electrophoresis, cyclic voltammetry, and electrochemical-impedance spectroscopy, and its performance was optimized under a variety of experimental conditions, especially the concentration of each reagent as well as the incubation time. Under the optimal experimental conditions, the reported biosensor showed a very low limit of detection of 0.10 fM (S/N = 3) and a wide linear dynamic range covering 0.50 fM to 100 pM toward microRNA-155 with excellent specificity, stability, and reproducibility. Finally, the biosensor was successfully applied to the detection of microRNA-155 extracted from the colon-cancer cell line DLD1, demonstrating its potential application in the sensitive detection of biological samples in the early diagnosis of diseases.

Spectrum-Resolved Dual-Color Electrochemiluminescence Immunoassay for Simultaneous Detection of Two Targets with Nanocrystals as Tags.

A spectrum-resolved dual-color electrochemiluminescence (ECL) immunoassay was designed and implemented to simultaneously detect carcinoembryonic antigen (CEA) and alpha fetoprotein (AFP) with CdTe (λmax = 776 nm) and CdSe (λmax = 550 nm) nanocrystals (NCs) as ECL tags. The CdTe and CdSe NCs were labeled with respective probe antibodies (Ab2) of CEA and AFP, respectively, and then immobilized onto the working electrode surface via sandwich-type immunoreactions. Both CdTe and CdSe NCs within the NCs immunocomplexes can be electrochemically reduced and simultaneously give off monochromatic ECL emissions in the near-infrared and greenish regions, respectively, when (NH4)2S2O8 was used as a cathodic ECL coreactant. The ECL spectra of the two surface-confined NCs were well separated and had no cross energy-transfer interactions, which made the dual-color immunoassay highly selective and sensitive toward respective target analytes. With the proposed ECL biosensor, CEA and AFP were simultaneously detected and quantified with an extremely low detection limit of 1 pg/mL for CEA and 10 fg/mL for AFP, respectively. This work demonstrated the probability of performing multianalyte assays via a spectrum-resolved ECL strategy with improved sensitivity and signal-to-noise ratio as compared to NCs-based fluorescent multianalyte assays.

An ultrasensitive electrogenerated chemiluminescence-based immunoassay for specific detection of Zika virus.

Zika virus (ZIKV) is a globally emerging mosquito-transmitted flavivirus that can cause severe fetal abnormalities, including microcephaly. As such, highly sensitive, specific, and cost-effective diagnostic methods are urgently needed. Here, we report a novel electrogenerated chemiluminescence (ECL)-based immunoassay for ultrasensitive and specific detection of ZIKV in human biological fluids. We loaded polystyrene beads (PSB) with a large number of ECL labels and conjugated them with anti-ZIKV monoclonal antibodies to generate anti-ZIKV-PSBs. These anti-ZIKV-PSBs efficiently captured ZIKV in solution forming ZIKV-anti-ZIKV-PSB complexes, which were subjected to measurement of ECL intensity after further magnetic beads separation. Our results show that the anti-ZIKV-PSBs can capture as little as 1 PFU of ZIKV in 100 µl of saline, human plasma, or human urine. This platform has the potential for development as a cost-effective, rapid and ultrasensitive assay for the detection of ZIKV and possibly other viruses in clinical diagnosis, epidemiologic and vector surveillance, and laboratory research.

Spectrum-Based Electrochemiluminescent Immunoassay with Ternary CdZnSe Nanocrystals as Labels.

Conventional electrochemiluminescence (ECL) research has been performed by detecting the total photons (i.e., the ECL intensity). Herein, systematic spectral exploration on the ECL of dual-stabilizers-capped ternary CdZnSe nanocrystals (NCs) and its sensing application were carried out on a homemade ECL spectral acquiring system. The ternary CdZnSe NCs could be repeatedly injected with electrons via some electrochemical ways and then result in strong cathodic ECL with the coupling of ammonium persulfate. ECL spectrum of the CdZnSe NCs was almost identical to corresponding photoluminescence spectrum, indicating that the excited states of CdZnSe NCs in ECL were essentially the same as those in photoluminescence. Importantly, after being labeled to the probe antibody (Ab2) of α-fetal protein (AFP) antigen, the ternary NCs in the Ab2|NCs conjugates could preserve their ECL spectrum very well. A spectrum-based ECL immunoassay was consequently proposed with the CdZnSe NCs as ECL tags and AFP as target molecules. The limit of detection is 0.010 pg/mL, with a signal-to-noise (S/N) ratio of 3, indicating a sensitive ECL sensing strategy that was different from the conventional ones. This work might open a pathway to the spectrally resolved ECL analysis with even-higher S/N ratios than the fluorescent analysis.

Effects of multi-walled carbon nanotubes on the electrogenerated chemiluminescence and fluorescence of CdTe quantum dots.

Effects of multi-walled carbon nanotubes (CNTs) that were immobilized on glassy carbon electrode (GCE) on the electrogenerated chemiluminescence (ECL) of CdTe quantum dots (QDs) using tri-n-propylamine (TPrA) and 2-(dibutylamino)ethanol (DBAE) as the anodic coreactant are reported. Depending on the solution concentration of coreactant and QDs, the surface-confined CNTs could either quench or enhance the ECL intensity. Lowering the solution concentration of QDs was found to be beneficial for enhancing ECL. A V-shaped profile of ECL intensity ratio (at CNTs over bare GCE) versus coreactant concentration suggested that either low or high concentrations of coreactant were needed for effective ECL generation. The ECL quenching by CNTs was believed to follow the typical dynamic quenching mechanism, which was confirmed by fluorescent data that provided a Stern-Volmer and an estimated quenching constant of 11.7 g/L and 1.2 × 10(9) L/g•s, respectively, for the excited state CdTe* quenching by CNTs in solution. Furthermore, the ECL performance at CNTs was also affected by the type of the coreactant used, where up to 30 times enhancement in ECL was observed from the CdTe/DBAE system under the given experimental conditions. Graphical Abstract Illustration of anodic quantum dots ECL enhancement and quenching by multi-walled carbon nanotubes.

Molecular-Counting-Free and Electrochemiluminescent Single-Molecule Immunoassay with Dual-Stabilizers-Capped CdSe Nanocrystals as Labels.

Biorelated single-molecule detection (SMD) has been achieved typically by imaging the redox fluorescent labels and then determining each label one by one. Herein, we demonstrated that the capping agents (i.e., mercaptopropionic acid and sodium hexametaphosphate) can facilitate the electrochemical involved hole (or electron) injecting process and improve the stability of the dual-stabilizers-capped CdSe nanocrystals (NCs), so that the CdSe NCs could be electrochemically and repeatedly inspired to excited states by giving off electrochemiluminescence (ECL) in a cyclic pattern. With the CdSe NCs as ECL label and carcinoembryonic antigen (CEA) as target molecule, a convenient single-molecule immunoassay was proposed by simply detecting the ECL intensity of the dual-stabilizers-capped CdSe NCs in a sandwich-typed immune complex. The limit of detection is 0.10 fg/mL at S/N = 3, which corresponds to about 6-8 CEA molecules in 20 µL of serum sample. Importantly, the ECL spectra of both CdSe NCs and its conjugate with probe antigen in the immune complex were almost identical to the photoluminescence spectrum of bare CdSe NCs, indicating that all emissions were originated from the same excited species. The molecular-counting-free and ECL-based SMD might be a promising alternative to the fluorescent SMD.

Investigation of perfluorooctanoic acid induced DNA damage using electrogenerated chemiluminescence associated with charge transfer in DNA.

An electrogenerated chemiluminescence (ECL)-DNA sensor was designed and fabricated for the investigation of DNA damage by a potential environmental pollutant, perfluorooctanoic acid (PFOA). The ECL-DNA sensor consisted of a Au electrode that had a self-assembled monolayer of 15 base-pair double-stranded (ds) DNA oligonucleotides with covalently attached semiconductor CdSe quantum dots (QDs) at the distal end of the DNA. Characterization of the ECL-DNA sensor was conducted with X-ray photoelectron spectroscopy (XPS), electrochemical impedance spectroscopy (EIS), ECL, and cyclic voltammetry before and after the exposure of the sensor to PFOA. Consistent data revealed that the dsDNA on Au was severely damaged upon the incubation of the electrode in PFOA, causing significant increase in charge (or electron) transfer (CT) resistance within DNA strands. Consequently, the cathodic coreactant ECL responses of the Au/dsDNA-QDs electrode in the presence of K2S2O8 were markedly decreased. The strong interaction between DNA and PFOA via the hydrophobic interaction, especially the formation of F···H hydrogen bonds by insertion of the difluoro-methylene group of PFOA into the DNA base pairs, was believed to be responsible for the dissociation or loosening of dsDNA structure, which inhibited the CT through DNA. A linear relationship between the ECL signal of the sensor and the logarithmical concentration of PFOA displayed a dynamic range of 1.00 × 10(-14)-1.00 × 10(-4) M, with a limit of detection of 1.00 × 10(-15) M at a signal-to-noise ratio of 3. Graphical Abstract Illustration of ECL detection of PFOA on a Au/dsDNA-QDs ECL-DNA sensor.

Sensitive determination of triacetone triperoxide explosives using electrogenerated chemiluminescence.

Sensitive and selective detection and quantification of high explosive triacetone triperoxide (TATP) with electrogenerated chemiluminescence (ECL) at a glassy carbon electrode in water-acetonitrile solvent mixture were reported. In the presence of ruthenium(II) tris(bipyridine), TATP or hydrogen peroxide derived from TATP via UV irradiation or acid treatment produced ECL emissions upon cathodic potential scanning. Interference from hydrogen peroxide on TATP detection was eliminated by pretreatment of the analyte with catalase enzyme. Selective detection of TATP from hexamethylene triperoxide diamine (HMTD, another common peroxide-based explosive) was realized by comparing ECL responses obtained from the anodic and the cathodic potential scanning; TATP produced ECL upon cathodic potential scanning only, whereas HMTD produced ECL upon both cathodic and anodic potential scanning. The hydroxyl radical formed after the electrochemical reduction of TATP was believed to be the key intermediate for ECL production, and its stability was strongly dependent on the solution composition, which was verified with electron paramagnetic resonance spectroscopy. A detection limit of 2.5 µM TATP was obtained from direct electrochemical reduction of the explosive or hydrogen peroxide derived from TATP in 70/30% (v/v) water-acetonitrile solutions, which was ~400 times lower than that reported previously based on liquid chromatography separation and Fourier transform infrared detection.

Ultrasensitive electrogenerated chemiluminescence biosensor for the determination of mercury ion incorporating G4 PAMAM dendrimer and Hg(II)-specific oligonucleotide.

A novel electrogenerated chemiluminescence (ECL) biosensor for highly sensitive and selective detection of mercury ion was developed on the basis of mercury-specific oligonucleotide (MSO) served as a molecular recognition element and the ruthenium(II) complex (Ru1) as an ECL emitting species. The biosensor was fabricated on a glassy carbon electrode coated with a thin layer of single wall carbon nanotubes, where the ECL probe, NH(2)-(CH(2))(6)-oligo(ethylene oxide)(6)-MSO↔Dend-Ru1, was covalently attached. The Dend-Ru1 pendant was prepared by covalent coupling Ru1 with the 4th generation polyamidoamine dendrimer (Dend), in which each dendrimer contained 35 Ru1 units so that a large amplification of ECL signal was obtained. Upon binding of Hg(2+) to thymine (T) bases of the MSO, the T-Hg-T structure was formed, and the MSO changed from its linear shape to a "hairpin" configuration. Consequently, the Dend-Ru1 approached the electrode surface resulting in the increase of anodic ECL signal in the presence of the ECL coreactant tri-n-propylamine. The reported biosensor showed a high reproducibility and possessed long-term storage stability (92.3% initial ECL recovery over 30 day's storage). An extremely low detection limit of 2.4 pM and a large dynamic range of 7.0 pM to 50 nM Hg(2+) were obtained. An apparent binding constant of 1.6 × 10(9)M(-1) between Hg(2+) and the MSO was estimated using an ECL based extended Langmuir isotherm approach involving multilayer adsorption. Determination of Hg(2+) contents in real water samples was conducted and the data were consistent with the results from cold vapor atomic fluorescence spectroscopy.

Cathodic stripping synthesis and cytotoxity studies of glutathione-capped CdTe quantum dots.

A cathodic stripping of Te precursor in the presence of Cd2+ and biocompatible glutathione (GSH) was reported for facile synthesis of lowly cytotoxic and highly luminescent CdTe quantum dots (QDs) in aqueous solution. The photoluminescence, electrogenerated chemiluminescence (ECL), toxicity, and cyto-osmosis of the QDs were evaluated to reveal their potential bio-applications. The morphology and composition of as-prepared QDs were investigated by HRTEM and powder XRD spectroscopy, which indicated that the QDs consisted of a CdTe core coated with a CdS shell. The obtained CdTe/CdS core/shell QDs possessed good crystallinity, narrow monodispersity and long-term stability. These QDs showed high fluorescence quantum yields of 49% to 63% over a broad spectral range of 540-650 nm. Efficient and stable ECL of QDs was observed on the anodic potential region upon the electrode potential cycled between 1.5 and -2.0 V versus Ag/AgCl. Furthermore, human liver cancer HepG2 cells were chosen as model cells for toxicity assay of QDs. Effects of the concentration, size, and incubation time of CdTe QDs capped with GSH or mercaptoacetic acid (MAA) on the cell metabolic viability and cyto-osmosis were evaluated. GSH-capped CdTe QDs could infiltrate cytomembrane and karyothecas, and were less cytotoxic than MAA-capped ones under the same experimental conditions. The reported CdTe QDs could be good candidates of fluorescent and ECL probes for biosensing and cell imaging.

Electrogenerated chemiluminescence determination of C-reactive protein with carboxyl CdSe/ZnS core/shell quantum dots.

Electrogenerated chemiluminescence (ECL) of water-soluble core/shell CdSe/ZnS quantum dots (QDs) coated with carboxylated polyethylene glycol polymers ("Qdot 625") was investigated in aqueous solutions using 2-(dibutylamino)ethanol (DBAE) and tri-n-propylamine (TPrA) as ECL coreactants. In both cases, ECL emissions at glassy carbon (GC) electrode appeared at the same potential of approximately 0.80 V vs. Ag/AgCl (3.0 M KCl), which was approximately 200 and approximately 150 mV more positive compared with the oxidation potentials for DBAE (approximately +0.60 V vs. Ag/AgCl) and TPrA (approximately +0.65 V vs. Ag/AgCl), respectively. The ECL intensity, however, was significantly affected by the type and the concentration of the ECL coreactant used as well as the nature of the working electrode. Under the present experimental conditions, ECL from DBAE was approximately 17 times stronger than that from TPrA. The maximum ECL was obtained at GC electrode when [DBAE] approximately = 53 mM, where a ratio of 11:3:1 in ECL intensity was evaluated for GC, Au, and Pt electrodes, respectively. The ECL emission of the Qdot 625/DBAE system had an apparent peak value of approximately 625 nm that matched well the fluorescence data. The QD as a label for ECL-based immunoassays of C-reactive protein (CRP) was realized by covalent binding of avidin on its surface, which allowed biotinylated anti-CRP to be attached and interacted with solution-phase CRP and the anti-CRP linked to micro-sized magnetic beads. The newly formed sandwich type aggregates were separated magnetically from the solution matrix, followed by the ECL generation at partially transparent Au nanoparticle-coated ITO electrode or Au/CD electrode in the presence of DBAE. Much stronger ECL responses were observed from the Au/CD electrode, at which a dynamic range of 1.0-10.0 microg mL(-1) CRP and a limit of detection of 1.0 microg mL(-1) CRP were obtained, respectively.

Double covalent coupling method for the fabrication of highly sensitive and reusable electrogenerated chemiluminescence sensors.

A double covalent coupling method for the fabrication of a highly sensitive and reusable electrogenerated chemiluminescence (ECL) chemical sensor for the detection of tertiary amines and ECL aptamer-based (ECL-AB) biosensor for the detection of cocaine is reported. The ECL sensors were constructed by covalent coupling of amino-containing Ru(bpy)(3)(2+) derivatives (Ru1, Ru(bpy)(3)(2+) = tris(2,2'-bipyridyl)ruthenium(II)) or cocaine aptamer-Ru1 to the surface of a paraffin-impregnated graphite electrode that had been covalently modified with a monolayer of 4-aminobenzene sulfonic acid via electrochemical oxidations. ECL performance of the newly developed chemical sensors was evaluated using tri-n-propylamine (TPrA) and metoclopramide (MCP) as model analytes. The sensors exhibited excellent sensitivity, stability, and reproducibility with a detection limit of 30 nM for TPrA and 2.0 nM for MCP, and relative standard deviations (RSDs) of 2.1% over 90 cyclic potential cycles (0 to 1.50 V vs Ag/AgCl) and 2.6% over 45 cycles (0.60 to +1.30 V vs Ag/AgCl) at 400 mV/s for 50 nM TPrA and 200 nM MCP, respectively. For the ECL-AB biosensor, it showed an extremely low detection limit of 10 pM for cocaine, and offered a good selectivity toward cocaine, heroin, and caffeine. This detection limit was about 4-6 orders of magnitude lower than that reported on the basis of alternating current (AC) voltammetry and optical aptamer-based cocaine biosensors. Additionally, the ECL-AB biosensor was highly reusable (RSD = 2.8%, n = 7) and possessed long-term storage stability (96.8% initial ECL recovery over 21 days storage). A binding constant of 4.6 +/- 0.3 x 10(9) M(-1) between cocaine and its aptamer was estimated using an ECL based Langmuir isotherm approach. Wide ranging applications of the presently reported strategy in fabricating various chemical sensors or biosensors are expected.

Sensitive determination of hexamethylene triperoxide diamine explosives, using electrogenerated chemiluminescence enhanced by silver nitrate.

Sensitive detection and quantification of hexamethylene triperoxide diamine (HMTD), which is one of commonly used explosives by terrorists, was presented on the basis of electrogenerated chemiluminescence (ECL) technology coupled with silver nitrate (AgNO3) enhancement in acetonitrile at a platinum electrode. Upon anodic potential scanning, HMTD irreversibly oxidized at approximately 1.70 V vs Ag/Ag+ (10 mM) at a scan rate of 50 mV/s, and the ECL profile was coincident with the oxidation potential of HMTD in the presence of ruthenium(II) tris(bipyridine) (Ru(bpy)3(2+)) luminophore species, which showed a half-wave potential of 0.96 V vs Ag/Ag+. The addition of small amounts of AgNO3 (0.50-7.0 mM) into the HMTD/Ru(bpy)3(2+) system resulted in significant enhancement in HMTD ECL production (up to 27 times). This enhancement was determined to be largely associated with NO3(-) and was linearly proportional to the concentrations of NO3(-) and Ag+ in solution. Homogeneous chemical oxidations of HMTD by electrogenerated NO3* and Ag(II) species proximity to the electrode were proposed to be responsible for the ECL enhancement. On the basis of cyclic voltammetry (CV) and CV digital simulations, standard potential values of 1.79 V vs Ag/Ag+ (or 1.98 V vs NHE) and 1.82 V vs Ag/Ag+ (or 2.01 V vs NHE) were estimated for Ag(II)/Ag(I) and NO3*/NO3(-) couples, respectively. A detection limit of 50 microM of HMTD was achieved with the current technique, which was 10 times more sensitive than that reported previously, which was based on a high-performance liquid chromatography/Fourier transform infrared (HPLC/FT-IR) detection method.

Electrochemical and electrogenerated chemiluminescent studies of a trinuclear complex, [((phen)2Ru(dpp))2RhCl2]5+, and its interactions with calf thymus DNA.

The electrochemical behavior of a trinuclear ruthenium(II)-containing complex, [((phen)(2)Ru(dpp))(2)RhCl(2)](5+) (where phen = 1,10-phenanthroline, dpp = 2,3-bis(2-pyridyl)pyrazine), was studied in acetonitrile (MeCN) and aqueous solutions. In MeCN containing 0.10 M tetra-n-butylammonium perchlorate (TBAP), the complex displayed a reversible, overlapping Ru(II/III) redox process with E(1/2) = +1.21 V vs Ag/Ag(+) (10 mM), an irreversible reduction of Rh(III/I) at -0.73 V vs Ag/Ag(+), and two quasi-reversible dpp/dpp(-) couples with E(1/2) = -1.11 and -1.36 V vs Ag/Ag(+) at a Pt electrode with a scan rate of 50 mV s(-1). In 0.20 M Tris buffer solution (pH 7.4), an irreversible, overlapping Ru(II/III) oxidation at +1.48 V vs Ag/AgCl (3 M KCl), and an irreversible reduction of Rh(III/II) at -0.78 V vs Ag/AgCl were observed at a glassy carbon electrode with a scan rate of 50 mV/s. Investigations on the electrogenerated chemiluminescence (ECL) of the complex revealed that 2-(dibutylamino) ethanol (DBAE) was superior to tri-n-propylamine (TPrA) as an ECL coreactant within their entire concentration range of 10-100 mM in MeCN, and in aqueous media, as low as 1.0 nM of the complex can be detected using TPrA coreactant ECL. A maximum ECL emission of 640 nm, which is about 55 nm blue shift to its fluorescence, was observed in MeCN with DBAE as a coreactant. Interactions of the complex with calf thymus DNA (ctDNA) were conducted with a flow-cell based quartz-crystal microbalance, and a binding constant of 2.5 x 10(5) M(-1) was calculated on the basis of the Langmuir isotherm equation.

Ultrasensitive detection of TNT in soil, water, using enhanced electrogenerated chemiluminescence.

The ultrasensitive detection of 2,4,6-trinitrotoluene (TNT) was accomplished on the basis of sandwich-type TNT immunoassay combined with electrogenerated chemiluminescence (ECL) technology. Biotinylated anti-TNT species were attached to the surface of 1-microm diameter streptavidin-coated magnetic beads (MB) and 10-microm diameter avidin-coated polystyrene microspheres/beads (PSB) pre-loaded with ECL labels ( approximately 7 billion hydrophobic ruthenium(II) tris(2,2'-bipyridine) (Ru(II)) molecules per bead) to form anti-TNT<-->MB and anti-TNT<-->PSB(Ru(II)) conjugates, respectively. Sandwich-type PSB(Ru(II))<-->anti-TNTanti-TNT<-->MB aggregates were formed when PSB(Ru(II))<-->anti-TNT was mixed with anti-TNT<-->MB conjugates in the presence of analyte TNT and 2.0% bovine serum albumin blocking agent. The newly formed aggregates were magnetically separated from the aqueous reaction media and dissolved in acetonitrile containing 0.10 M tri-n-propylamine ECL coreactant-0.055 M trifluoroacetic acid-0.10 M tetrabutylammonium tetrafluoroborate electrolyte. ECL as well as cyclic voltammetric measurements were carried out with a potential scan from 0 to 2.8 V vs Ag/Ag(+), and the integrated ECL intensity was found to be linearly proportional to the analyte TNT concentration over the range of 0.10-1000 ppt (pg mL(-1)). The limit of detection (

Electrochemistry and electrogenerated chemiluminescence of all-trans conjugated polymer poly[distyrylbenzene-b-(ethylene oxide)]s.

The electrochemistry and electrogenerated chemiluminescence (ECL) of two linear, stereoregular, and structurally defined PPV derivatives, poly[distyrylbenzene-b-(ethylene oxide)]s, with respective 12 and 16 of ethylene oxide repeat units in the backbone, abbreviated as DE-1 and DE-2, have been studied on glassy carbon and Pt electrodes in CH2Cl2 and CH3CN containing 0.10 M tetra-n-butylammonium perchlorate (TBAP). In CH2Cl2, a one-electron transfer, reversible oxidation at approximately 0.75 V vs Ag/Ag+ (10 mM AgNO3 in CH3CN) was observed for both polymers. Porous polymer films were electrochemically formed on the electrode with multiple cyclic potential scanning. Cast films of DE-1 and DE-2 on the electrode prepared from 1.0 mM of the corresponding CH2Cl2 solutions were used for studies in CH3CN containing 0.10 M TBAP due to their limited solubility in the solvent. A film-type of oxidation was found at approximately 0.80 V vs Ag/Ag+ in CH3CN when a scan rate of less than 1 V/s was used. The soluble oxidation product can be captured and reduced and then reoxidized in solution-phase at the electrode at a relatively high scan rate of, e.g., 2 V/s. ECL responses with a maximum emission at approximately 1.10 V vs Ag/Ag+ were obtained with the cast films in CH3CN (0.10 M TBAP) in the presence of 43 mM tri-n-propylamine (TPrA) after both TPrA and film were oxidized. The ECL is believed to be resulted from the interaction between the oxidized polymer species and the strong reducing TPrA free radical (TPrA*) generated after the deprotonation of TPrA*+ cation species.