Induced giant piezoelectricity in centrosymmetric oxides.

Piezoelectrics are materials that linearly deform in response to an applied electric field. As a fundamental prerequisite, piezoelectric materials must have a noncentrosymmetric crystal structure. For more than a century, this has remained a major obstacle for finding piezoelectric materials. We circumvented this limitation by breaking the crystallographic symmetry and inducing large and sustainable piezoelectric effects in centrosymmetric materials by the electric field-induced rearrangement of oxygen vacancies. Our results show the generation of extraordinarily large piezoelectric responses [with piezoelectric strain coefficients (d33) of ~200,000 picometers per volt at millihertz frequencies] in cubic fluorite gadolinium-doped CeO2-x films, which are two orders of magnitude larger than the responses observed in the presently best-known lead-based piezoelectric relaxor-ferroelectric oxide at kilohertz frequencies. These findings provide opportunities to design piezoelectric materials from environmentally friendly centrosymmetric ones.

The emergence of magnetic ordering at complex oxide interfaces tuned by defects.

Complex oxides show extreme sensitivity to structural distortions and defects, and the intricate balance of competing interactions which emerge at atomically defined interfaces may give rise to unexpected physics. In the interfaces of non-magnetic complex oxides, one of the most intriguing properties is the emergence of magnetism which is sensitive to chemical defects. Particularly, it is unclear which defects are responsible for the emergent magnetic interfaces. Here, we show direct and clear experimental evidence, supported by theoretical explanation, that the B-site cation stoichiometry is crucial for the creation and control of magnetism at the interface between non-magnetic ABO3-perovskite oxides, LaAlO3 and SrTiO3. We find that consecutive defect formation, driven by atomic charge compensation, establishes the formation of robust perpendicular magnetic moments at the interface. Our observations propose a route to tune these emerging magnetoelectric structures, which are strongly coupled at the polar-nonpolar complex oxide interfaces.

Syngas generation from n-butane with an integrated MEMS assembly for gas processing in micro-solid oxide fuel cell systems.

An integrated system of a microreformer and a carrier allowing for syngas generation from liquefied petroleum gas (LPG) for micro-SOFC application is discussed. The microreformer with an overall size of 12.7 mm × 12.7 mm × 1.9 mm is fabricated with micro-electro-mechanical system (MEMS) technologies. As a catalyst, a special foam-like material made from ceria-zirconia nanoparticles doped with rhodium is used to fill the reformer cavity of 58.5 mm(3). The microreformer is fixed onto a microfabricated structure with built-in fluidic channels and integrated heaters, the so-called functional carrier. It allows for thermal decoupling of the cold inlet gas and the hot fuel processing zone. Two methods for heating the microreformer are compared in this study: a) heating in an external furnace and b) heating with the two built-in heaters on the functional carrier. With both methods, high butane conversion rates of 74%-85% are obtained at around 550 °C. In addition, high hydrogen and carbon monoxide yields and selectivities are achieved. The results confirm those from classical lab reformers built without MEMS technology (N. Hotz et al., Chem. Eng. Sci., 2008, 63, 5193; N. Hotz et al., Appl. Catal., B, 2007, 73, 336). The material combinations and processing techniques enable syngas production with the present MEMS based microreformer with high performance for temperatures up to 700 °C. The functional carrier is the basis for a new platform, which can integrate the micro-SOFC membranes and the gas processing unit as subsystem of an entire micro-SOFC system.

In-plane and out-of-plane ferroelectric instabilities in epitaxial SrTiO3 films.

The in-plane and out-of-plane ferroelectric instabilities in compressed (100)-epitaxial SrTiO3 films were examined by infrared reflection spectroscopy. The strongly stiffened in-plane soft mode frequency softened very slowly on cooling. On the other hand, the silent mode appeared at around 150 K, indicating an out-of-plane ferroelectric transition. This behavior points to a split of in-plane and out-of-plane ferroelectric instability temperatures due to the lowered symmetry of the SrTiO3 lattice caused by mechanical misfit strain. Infrared spectroscopy provides a possibility to detect such an effect in the strained epitaxial ferroelectric films.

PZT thin films for microsensors and actuators: Where do we stand?

This paper reviews deposition, integration, and device fabrication of PbZr(x)Ti(1-x)O(3) (PZT) films for applications in micro-electromechanical systems. An ultrasonic micromotor is described as an example. A summary of the published data on piezoelectric properties is given. The figures of merit for various applications are discussed. Some considerations and results on operation, reliability, and depolarization of PZT thin films are presented. The state of the art allows some preliminary conclusions.

PZT thin film actuated elastic fin micromotor.

A piezoelectric elastic fin micromotor based on a PbZr(0.53 )Ti(0.47)O(3) thin film driving a micromachined silicon membrane was fabricated and studied. The stator was characterized by interferometry, and a laser set-up was used to measure the angular velocity and acceleration of the motor. The torque, the output power, and the efficiency of the device were extracted from these measurements. Values up to 1020 rpm and 0.94 microNm were observed for the velocity and the torque, respectively, which would be sufficient for a wristwatch application. The present version exhibited an efficiency of 0.17%, which could theoretically be increased to 4.8%