The effects of electrochemical pretreatment and curing environment on strength and leaching of stabilized/solidified contaminated sediment.

Stabilization and solidification (S/S) is known to improve the structural properties of sediment and reduce contaminant mobility, enabling the utilization of dredged contaminated sediment. Further reduction of contaminants (e.g., tributyltin (TBT) and metals) can be done using electrochemical treatment prior to S/S and could potentially minimize contaminant leaching. This is the first study on how electrochemical pretreatment affects the strength and leaching properties of stabilized sediments. It also investigates how salinity and organic carbon in the curing liquid affect the stabilized sediment.The results showed that the electrolysis reduced the content of TBT by 22% and zinc by 44% in the sediment. The electrolyzed stabilized samples met the requirements for compression strength and had a reduced surface leaching of zinc. Curing in saline water was beneficial for strength development and reduced the leaching of TBT compared to curing in fresh water. The results indicate that pretreatment prior to stabilization could be beneficial in reducing contaminant leaching and recovering metals from the sediment. The conclusion is that a better understanding of the changes in the sediment caused by electrochemical treatment and how these changes interact with stabilization reactions is needed. In addition, it is recommended to investigate the strength and leaching behavior in environments similar to the intended in situ conditions.

Removal of organotin compounds and metals from Swedish marine sediment using Fenton's reagent and electrochemical treatment.

Metal and tributyltin (TBT) contaminated sediments are problematic for sediment managers and the environment. This study is the first to compare Fenton's reagent and electrochemical treatment as remediation methods for the removal of TBT and metals using laboratory-scale experiments on contaminated dredged sediment. The costs and the applicability of the developed methods were also compared and discussed. Both methods removed > 98% TBT from TBT-spiked sediment samples, while Fenton's reagent removed 64% of the TBT and electrolysis 58% of the TBT from non-spiked samples. TBT in water phase was effectively degraded in both experiments on spiked water and in leachates during the treatment of the sediment. Positive correlations were observed between TBT removal and the added amount of hydrogen peroxide and current density. Both methods removed metals from the sediment, but Fenton's reagent was identified as the most potent option for effective removal of both metals and TBT, especially from highly metal-contaminated sediment. However, due to risks associated with the required chemicals and low pH level in the sediment residue following the Fenton treatment, electrochemical treatment could be a more sustainable option for treating larger quantities of contaminated sediment.

Integrated cost and environmental impact assessment of management options for dredged sediment.

Large quantities of sediment must be dredged regularly to enable marine transport and trade. The sediments are often polluted, with e.g. metals, which limits the management options. The aim of this study has been to assess costs and environmental impacts (impact on climate, marine organisms, etc.) of different management options for polluted dredged sediment, by combining life-cycle assessment (LCA) of the climate impact, scoring of other environmental aspects and a cost evaluation. This approach has been used to study both traditional and new management alternatives for a real port case. The studied options include landfilling, deep-sea disposal, construction of a port area using a stabilization and solidification (S/S) method, and a combination of the aforementioned methods with the innovative option of metal recovery through sediment electrolysis. The LCA showed that deep-sea disposal had the lowest climate impact. The assessment of the other environmental impacts showed that the result varied depending on the pollution level and the time perspective used (short or long-term). Using sediment for construction had the highest climate impact, although other environmental impacts were comparably low. Electrolysis was found to be suitable for highly polluted sediments, as it left the sediment cleaner and enabled recovery of precious metals, however the costs were high. The results highlight the complexity of comparing different environmental impacts and the benefits of using integrated assessments to provide clarity, and to evaluate both the synergetic and counteracting effects associated with the investigated scenarios and may aid early-stage decision making.

Low impact leaching agents as remediation media for organotin and metal contaminated sediments.

All over the world, elevated levels of metals and the toxic compound tributyltin (TBT) and its degradation products are found in sediments, especially close to areas associated with shipping and anthropogenic activities. Ports require regular removal of sediments. As a result, large volumes of often contaminated sediments must be managed. The aim of this study was to investigate enhanced leaching as a treatment method for organotin (TBT) and metal (Cu and Zn) contaminated marine sediments. Thus, enabling the possibility to reuse these cleaner masses e.g. in construction. In addition to using acid and alkaline leaching agents that extract the OTs and metals but reduce the management options post treatment, innovative alternatives such as EDDS, hydroxypropyl cellulose, humic acid, iron colloids, ultra-pure Milli-Q water, saponified tall oil ("soap"), and NaCl were tested. Organotin removal ranged from 36 to 75%, where the most efficient leaching agent was Milli-Q water, which was also the leaching agent achieving the highest removal rate for TBT (46%), followed by soap (34%). The TBT reduction accomplished by Milli-Q water and soap leaching enabled a change in Swedish sediment classification from the highest class to the second highest class. The highest reduction of Zn was in HPC leached samples (39% removal) and Cu in EDDS leached samples (33% removal). Although high metal and OT leaching were achieved, none of the investigated leaching agents are sufficiently effective for the removal of both metals and OTs. The results of this study indicate that leaching with ultra-clean water, such as Milli-Q water, may be sufficient to treat TBT contaminated sediments and potentially allow mass reuse.

Integrated assessment of management strategies for metal-contaminated dredged sediments - What are the best approaches for ports, marinas and waterways?

Sediments in ports, marinas and waterways around the world are often contaminated with metals arising from anthropogenic activities. Regular dredging is needed to achieve an appropriate water depth and reduce the environmental impact of pollutants. The aim of this study was to develop an integrated assessment method for comparing various management strategies for dredged sediments at six case study sites in Sweden. Short- and long-term environmental impacts were investigated for different management approaches, including landfilling, deep-sea disposal, metal extraction in combination with the two aforementioned, and natural recovery (no dredging). The potential value of metals in the sediments was estimated using sediment metal contents and current metal prices. Additionally, an assessment of how metal extraction could result in lower management costs was carried out. The cost of the different management approaches was calculated and evaluated together with the corresponding environmental impacts. This study shows that there is a monetary value in dredged materials, in terms of metal content, and that the materials can potentially be used for metal extraction. Metal extraction may also help to reduce the management costs, as cleaner materials are cheaper to handle. The choice of metal recovery method is important in both monetary and environmental terms, potentially contributing to a circular economy. In the future, metal recovery may become more profitable, as technologies are improved, and due to probable increases in metal prices and landfill costs.

Design of an online health-promoting community: negotiating user community needs with public health goals and service capabilities.

BACKGROUND: An online health-promoting community (OHPC) has the potential to promote health and advance new means of dialogue between public health representatives and the general public. The aim of this study was to examine what aspects of an OHPC that are critical for satisfying the needs of the user community and public health goals and service capabilities. METHODS: Community-based participatory research methods were used for data collection and analysis, and participatory design principles to develop a case study OHPC for adolescents. Qualitative data from adolescents on health appraisals and perspectives on health information were collected in a Swedish health service region and classified into categories of user health information exchange needs. A composite design rationale for the OHPC was completed by linking the identified user needs, user-derived requirements, and technical and organizational systems solutions. Conflicts between end-user requirements and organizational goals and resources were identified. RESULTS: The most prominent health information needs were associated to food, exercise, and well-being. The assessment of the design rationale document and prototype in light of the regional public health goals and service capabilities showed that compromises were needed to resolve conflicts involving the management of organizational resources and responsibilities. The users wanted to discuss health issues with health experts having little time to set aside to the OHPC and it was unclear who should set the norms for the online discussions. CONCLUSIONS: OHPCs can be designed to satisfy both the needs of user communities and public health goals and service capabilities. Compromises are needed to resolve conflicts between users' needs to discuss health issues with domain experts and the management of resources and responsibilities in public health organizations.

Lateral angle: a method for sexing using the petrous bone.

We report on the results of applying the so-called lateral angle method for sex determination on skeletal remains. The lateral angle denotes the angle of the internal auditory canal in relation to the medial surface of the petrous part of the temporal bone. The method involves making a small cast of the proximal part of the internal acoustic canal and determining the angle at which the canal opens up to the surface of the petrous bone. The method has the great advantage of utilizing one of the sturdiest bone elements of the human skeleton, and may thus be especially suited for analyses of very fragmented skeletal remains or cremated bones, where the petrous bone may still be readily recognizable. The method was tested using a forensic sample of 113 petrous bones with known sex. Intra- and interobserver testing was also performed. We found a statistically significant difference in angle size between males and females (mean angle size of males, 39.3 degrees ; mean angle size of females, 48.2 degrees ; P < 0.001). There was no bilateral difference in angle size. In blind trials, 83.2% of petrous bones were assigned to the correct sex. We also tested the lateral angle method against an archaeological skeletal sample. True sex was not known for this sample; instead, sexing had been carried out by assessing pelvic and cranial morphology in independent trials. We found a higher concordance between the lateral angle and "pelvic" sex than for lateral angle and "cranial" sex. Finally, we note that subadult sexing may also be possible with this method.