Modulating Surface Architecture and Electronic Conductivity of Li-rich Manganese-Based Cathode.

Li-rich manganese-based cathode (LRMC) has attracted intense attention to developing advanced lithium-ion batteries with high energy density. However, LRMC is still plagued by poor cyclic stability, undesired rate capacity, and irreversible oxygen release. To address these issues, herein, a feasible polyvinylidene fluoride (PVDF)-assisted interface modification strategy is proposed for modulating the surface architecture and electronic conductivity of LRMC by intruding the F-doped carbon coating, spinel structure, and oxygen vacancy on the LRMC, which can greatly enhance the cyclic stability and rate capacity, and restrain the oxygen release for LRMC. As a result, the modified material delivers satisfactory cyclic performance with a capacity retention of 90.22% after 200 cycles at 1 C, an enhanced rate capacity of 153.58 mAh g-1 at 5 C and 126.32 mAh g-1 at 10 C, and an elevated initial Coulombic efficiency of 85.63%. Moreover, the thermal stability, electronic conductivity, and structure stability of LRMC are also significantly improved by the PVDF-assisted interface modification strategy. Therefore, the strategy of simultaneously modulating the surface architecture and the electronic conductivity of LRMC provides a valuable idea to improve the comprehensive electrochemical performance of LRMC, which offers a promising reference for designing LRMC with high electrochemical performance.

Constructing a Cr-Substituted Co-Free Li-Rich Ternary Cathode with a Spinel-Layered Biphase Interface.

Lithium-rich manganese-based layered oxides (LRMOs) have recently attracted enormous attention on account of their remarkably big capacity and high working voltage. However, some inevitable inherent drawbacks impede their wide-scale commercial application. Herein, a kind of Cr-containing Co-free LRMO with a topical spinel phase (Li1.2Mn0.54Ni0.13Cr0.13O2) has been put forward. It has been found that the high valence of Cr6+ can reduce the Li+ ion content and induce the formation of a local spinel phase by combining more Li+ ions, which is beneficial to eliminate the phase boundary between the spinel phase and the bulk phase of the LRMO material, thus dramatically avoiding phase separation during the cycling process. In addition, the introduction of Cr can also expand the layer spacing and construct a stronger Cr-O bond compared with Mn-O, which enables to combine the transition metal (TM) slab to prevent the migration of TM ions and the transformation of the bulk phase to the spinel phase. Simultaneously, the synergistic effect of the successfully constructed spinel-layered biphase interface and the strong Cr-O bond can effectively impede the escape of lattice oxygen during the initial activation process of Li2MnO3 and provide the fast diffusion path for Li+ ion transmission, thus further reinforcing the configurable stability. Besides, Cr-LRMO presents an ultrahigh first discharge specific capacity of 310 mAh g-1, an initial Coulombic efficiency of as high as 92.09%, a good cycling stability (a capacity retention of 94.70% after 100 cycles at 1C), and a small voltage decay (3.655 mV per cycle), as well as a good rate capacity (up to 165.88 mAh g-1 at 5C).

Reversible Oxygen Redox Chemistry in High-Entropy P2-Type Manganese-Based Cathodes via Self-Regulating Mechanism.

The irreversible oxygen-redox reactions in the high-voltage region of sodium-layered cathode materials lead to poor capacity retention and structural instability during cycling, presenting a significant challenge in the development of high-energy-density sodium-ion batteries. This work introduces a high-entropy design for layered Na0.67Li0.1Co0.1Cu0.1Ni0.1Ti0.1Mn0.5O2 (Mn-HEO) cathode with a self-regulating mechanism to extend specific capacity and energy density. The oxygen redox reaction was activated during the initial charging process, accompanied by the self-regulation of active elements, enhancing the ionic bonds to form a vacancy wall near the TM vacancies and thus preventing the migration of transition metal elements. Systematic in situ/ex situ characterizations and theoretical calculations comprehensively support the understanding of the self-regulation mechanism of Mn-HEO. As a result, the Mn-HEO cathode exhibits a stable structure during cycling. It demonstrates almost zero strain within a wide voltage range of 2.0-4.5 V with a remarkable specific capacity (177 mAh g-1 at 0.05 C) and excellent long-term cycling stability (87.6% capacity retention after 200 cycles at 2 C). This work opens a new pathway for enhancing the stability of oxygen-redox chemistry and revealing a mechanism of crystal structure evolution for high-energy-density layered oxides.

A novel ACE inhibitory peptide from Pelodiscus sinensis Wiegmann meat water-soluble protein hydrolysate.

Pelodiscus sinensis meat is a nutritional food and tonic with angiotensin-converting enzyme (ACE) inhibitory activities. To identify the bioactive substances responsible, several bioinformatics methods were integrated to enable a virtual screening for bioactive peptides in proteins identified within a water-soluble protein fraction of Pelodiscus sinensis meat by Shotgun proteomics. The peptides were generated from the identified proteins by in silico proteolysis using six proteases. A comparison of the numbers of proteins suitable for digestion with each enzyme and the iBAQ (intensity-based absolute quantification) values for these proteins revealed that bromelain and papain were the most suitable proteases for this sample. Next, the water solubility, toxicity, and ADMET (absorption/distribution/metabolism/excretion/toxicity) properties of these peptides were evaluated in silico. Finally, a novel ACE inhibitory peptide IEWEF with an IC50 value of 41.33 µM was identified. The activity of the synthesized peptide was verified in vitro, and it was shown to be a non-competitive ACE inhibitor. Molecular docking revealed that IEWEF could tightly bind to C-ACE, and N-ACE with energies less than 0 kJ mol-1, and the peptide IEWEF can form hydrogen bonds with C-ACE and N-ACE respectively. These results provide evidence that bioactive peptides in the water-soluble protein fraction account for (at least) some of the ACE inhibitory activities observed in Pelodiscus sinensis meat. Furthermore, our research provides a workflow for the efficient identification of novel ACE inhibitory peptides from complex protein mixtures.

Synergistic electrochemical catalysis by high-entropy metal phosphide in lithium-sulfur batteries.

The shuttle effect and sluggish redox kinetics of polysulfides have hindered the development of lithium-sulfur batteries (LSBs) as premier energy storage devices. To address these issues, a high-entropy metal phosphide (NiCoMnFeCrP) was synthesized using the sol-gel method. NiCoMnFeCrP, with its rich metal species, exhibits strong synergistic effects and provides numerous catalytic active sites for the conversion of polysulfides. These active sites, possessing significant polarity, can bond with polysulfides. In situ ultraviolet-visible were conducted to monitor the dynamic changes in species and concentrations of polysulfides, validating the ability of NiCoMnFeCrP to facilitate the conversion of polysulfides. The batteries with the NiCoMnFeCrP catalyst as functional separators exhibited minimal capacity decay rates of 0.04 % and 0.23 % after 100 cycles at 0 °C and 60 °C, respectively. This indicates that the NiCoMnFeCrP catalyst possesses good thermal stability. Meanwhile, its area capacity can reach 4.78 mAh cm-2 at a high sulfur load of 4.54 mg cm-2. In conclusion, NiCoMnFeCrP achieves the objective of mitigating the shuttle effect and accelerating the kinetics of the redox reaction, thereby facilitating the commercialization of LSBs.

Construction and catalysis role of a kinetic promoter based on lithium-insertion technology and proton exchange strategy for lithium-sulfur batteries.

The high theoretical energy density and specific capacity of lithium-sulfur (Li-S) batteries have garnered considerable attention in the prospective market. However, ongoing research on Li-S batteries appears to have encountered a bottleneck, with unresolved key technical challenges such as the significant shuttle effect and sluggish reaction kinetics. This investigation explores the catalytic efficacy of three catalysts for Li-S batteries and elucidates the correlation between their structure and catalytic impacts. The results suggest that the combined utilization of lithium-insertion technology and a proton exchange approach for δ-MnO2 can optimize its electronic structure, resulting in an optimal catalyst (H/Li inserted δ-MnO2, denoted as HLM) for the sulfur reduction reaction. The replacement of Mn sites in δ-MnO2 with Li atoms can enhance the structural stability of the catalyst, while the introduction of H atoms between transition metal layers contributes to the satisfactory catalytic performance of HLM. Theoretical calculations demonstrate that the bond length of Li2S4 adsorbed by the HLM molecule is elongated, thereby facilitating the dissociation process of Li2S4 and enhancing the reaction kinetics in Li-S batteries. Consequently, the Li-S battery utilizing HLM as a catalyst achieves a high areal specific capacity of 4.2 mAh cm-2 with a sulfur loading of 4.1 mg cm-2 and a low electrolyte/sulfur (E/S) ratio of 8 µL mg-1. This study introduces a methodology for designing effective catalysts that could significantly advance practical developments in Li-S battery technology.

Concentration-Gradient Structural LiFe0.5Mn0.5PO4/C Prepared via Co-precipitation Reaction for Advanced Lithium-Ion Batteries.

The intrinsically low electronic conductivity and slow ion diffusion kinetics limit further development of olivine LiFexMn1-xPO4 cathode materials. In this paper, with the aim of improving the performance of such materials and alleviating the Jahn-Taller effect of Mn3+ ion, a bimetallic oxalate precursor with gradient distribution of elemental concentration followed with an efficient process is applied to synthesize LiFe0.5Mn0.5PO4 nanocomposite. The results shown that with certain structural modulation of the precursor, the discharge capacity of synthesized LiFe0.5Mn0.5PO4 increased from 149 mAh g-1 to 156 mAh g-1 at 0.1 C, the cycling capacity was also remarkably improved. the Fe0.5Mn0.5C2O4 ⋅ 2H2O-1 precursor with gradient distribution of elemental concentration effectively restricts the reaction between electrode material and electrolyte, thereby alleviates the dissolution of Mn3+ ion, reduces the decay of capacity and improves the stability of the material.

Enabling Rapid and Stable Sodium Storage via a P2-Type Layered Cathode with High-Voltage Zero-Phase Transition Behavior.

Currently, a major target in the development of Na-ion batteries is the concurrent attainment of high-rate capacity and long cycling stability. Herein, an advanced Na-ion battery with high-rate capability and long cycle stability based on Li/Ti co-doped P2-type Na0.67 Mn0.67 Ni0.33 O2 , a host material with high-voltage zero-phase transition behavior and fast Na+ migration/conductivity during dynamic de-embedding process, is constructed. Experimental results and theoretical calculations reveal that the two-element doping strategy promotes a mutually reinforcing effect, which greatly facilitates the transfer capability of Na+ . The cation Ti4+ doping is a dominant high voltage, significantly elevating the operation voltage to 4.4 V. Meanwhile, doping Li+ shows the function in charge transfer, improving the rate performance and prolonging cycling lifespan. Consequently, the designed P2-Na0.75 Mn0.54 Ni0.27 Li0.14 Ti0.05 O2 cathode material exhibits discharge capacities of 129, 104, and 85 mAh g- 1 under high voltage of 4.4 V at 1, 10, and 20 C, respectively. More importantly, the full-cell delivers a high initial capacity of 198 mAh g-1 at 0.1 C (17.3 mA g-1 ) and a capacity retention of 73% at 5 C (865 mA g-1 ) after 1000 cycles, which is seldom witnessed in previous reports, emphasizing their potential applications in advanced energy storage.

P2/O3 Biphasic Cathode Material through Magnesium Substitution for Sodium-Ion Batteries.

P2-type Fe-Mn-based oxides offer excellent discharge specific capacity and are as affordable as typical layered oxide cathode materials for sodium-ion batteries (SIBs). After Cu modification, though they can improve the cycling performance and air stability, the discharge specific capacity will be reduced. Considering the complementary nature of biphasic phases in electrochemistry, hybridizing P2/O3 hybrid phases can enhance both the storage performance of the battery and specific capacity. Herein, a hybrid phase composite with high capacity and good cycle performance is deliberately designed and successfully prepared by controlling the amount of Mg doping in the layered oxide. It has been found that the introduction of Mg can activate anion redox in the oxide layer, resulting in a significant increase in the specific discharge capacity of the material. Meanwhile, the dual-phase structure can produce an interlocking effect, thus effectively alleviating structure strain. The degradation of cycling performance caused by structural damage during the high-voltage charging and discharging process is clearly mitigated. The results show that the specific discharge capacity of Na0.67Cu0.2Mg0.1Fe0.2Mn0.5O2 is as high as 212.0 mAh g-1 at 0.1C rate and 186.2 mAh g-1 at 0.2C rate. After 80 cycles, the capacity can still maintain 88.1%. Moreover, the capacity and cycle performance as well as the stability can still remain stable even in the high-voltage window. Therefore, this work offers an insightful exploration for the development of composite cathode materials for SIBs.

Sustained Release-Driven Interface Engineering Enables Fast Charging Lithium Metal Batteries.

LiNO3 has attracted intensive attention as a promising electrolyte additive to regulate Li deposition behavior as it can form favorable Li3N, LiNxOy species to improve the interfacial stability. However, the inferior solubility in carbonate-based electrolyte restricts its application in high-voltage Li metal batteries. Herein, an artificial composite layer (referred to as PML) composed of LiNO3 and PMMA is rationally designed on Li surface. The PML layer serves as a reservoir for LiNO3 release gradually to the electrolyte during cycling, guaranteeing the stability of SEI layer for uniform Li deposition. The PMMA matrix not only links the nitrogen-containing species for uniform ionic conductivity but also can be coordinated with Li for rapid Li ions migration, resulting in homogenous Li-ion flux and dendrite-free morphology. As a result, stable and dendrite-free plating/stripping behaviors of Li metal anodes are achieved even at an ultrahigh current density of 20 mA cm-2 (>570 h) and large areal capacity of 10 mAh cm-2 (>1200 h). Moreover, the Li||LiFePO4 full cell using PML-Li anode undergoes stable cycling for 2000 cycles with high-capacity retention of 94.8%. This facile strategy will widen the potential application of LiNO3 in carbonate-based electrolyte for practical LMBs.

Improving Natural Microcrystalline Graphite Performances by a Dual Modification Strategy toward Practical Application of Lithium Ion Batteries.

Microcrystalline graphite (MG), as a kind of natural graphite (NG), holds great potential for use as an anode material for lithium-ion batteries (LIBs) due to low raw material cost, good electrolyte compatibility, and relatively long cycle life. Nevertheless, the relatively low reversible capacity and poor initial Coulombic efficiency (ICE) of the MG anode largely limit its practical application in LIBs. In order to improve the lithium storage capacity of MG, three kinds of oxidant intercalators are applied to treat the original MG, and the as-obtained MG is further modified by a thin carbon layer. The results indicate that using H2SO4-C2H2O4 as oxidant intercalators and subsequent carbon coating layer modification are the optimum techniques, and they can increase the interlayer distance, introduce defects to decrease the volume expansion, and generate channels for fast Li+ diffusion. Meanwhile, the carbon coating layer can reduce the specific surface area of graphite and greatly improve the ICE and cycling performance. Especially, the OEMGC-2 anodes prepared by the dual modification strategies represent a high reversible capacity of 349.4 mA h g-1 at 0.2C with a satisfactory ICE of 90.2%, indicating that the MG can also be considered as a high performance and low-cost anode material of LIBs.

An Integrated Analysis of microRNAs and the Transcriptome Reveals the Molecular Mechanisms Underlying the Regulation of Leaf Development in Xinyang Maojian Green Tea (Camellia sinensis).

Xinyang Maojian (XYMJ) tea is one of the world's most popular green teas; the development of new sprouts directly affects the yield and quality of tea products, especially for XYMJ, which has hairy tips. Here, we used transcriptome and small RNA sequencing to identify mRNAs and miRNAs, respectively, involved in regulating leaf development in different plant tissues (bud, leaf, and stem). We identified a total of 381 conserved miRNAs. Given that no genomic data for XYMJ green tea are available, we compared the sequencing data for XYMJ green tea with genomic data from a closely related species (Tieguanyin) and the Camellia sinensis var. sinensis database; we identified a total of 506 and 485 novel miRNAs, respectively. We also identified 11 sequence-identical novel miRNAs in the tissues of XYMJ tea plants. Correlation analyses revealed 97 miRNA-mRNA pairs involved in leaf growth and development; the csn-miR319-2/csnTCP2 and miR159-csnMYB modules were found to be involved in leaf development in XYMJ green tea. Quantitative real-time PCR was used to validate the expression levels of the miRNAs and mRNAs. The miRNAs and target genes identified in this study might shed new light on the molecular mechanisms underlying the regulation of leaf development in tea plants.

MoO2/t-C3N4 Heterogeneous Materials with Bidirectional Catalysis for the Rapid Conversion of S Species in Li-S Batteries.

Li-S batteries have drawn a lot of attention for their high theoretical specific capacity and significant economic benefits. However, the shuttle effect of polysulfides prevents them from being used widely. To tackle this difficulty, a heterogeneous structure based on tubular carbon nitride with evenly dispersed molybdenum dioxide nanoparticles (MoO2/t-C3N4) as the S host is constructed in this work. As a polar material with a large specific surface area, MoO2/t-C3N4 has a strong anchoring effect on polysulfide. Additionally, the heterogeneous material has excellent bidirectional catalytic ability for the redox process of S species based on the action of the built-in electric field formed by electron directional transfer. Not only does it improve the reaction kinetics of the redox process of the polysulfides but it also prevents polysulfides from accumulating on the surface of the modified material and deactivating it, further improving the utilization of the active material. Thus, MoO2/t-C3N4/S shows the high initial-discharge specific capacity of 812.7 mAh g-1 at the current density of 5C, and the Coulombic efficiency is maintained at more than 95% after 400 charge/discharge cycles. Moreover, MoO2/t-C3N4/S achieved a capacity retention of 89% after 100 cycles at the current density of 0.1C under the high S loading. Therefore, the research results of this work provide a trustworthy reference for the future commercial application of Li-S batteries.

Converting commercial Bi2O3 particles into Bi2O2Se@Bi4O8Se nanosheets for "rocking chair" zinc-ion batteries.

The development of a low-cost, high-capacity, and insertion-type anode is key for promoting "rocking chair" zinc-ion batteries. Herein, commercial Bi2O3 (BiO) particles are transformed into Bi2O2Se@Bi4O8Se (BiOSe) nanosheets through a simple selenylation process. The change in morphology from commercial BiO particle to BiOSe nanosheet leads to an increased specific surface area of the material. The enhanced electronic/ionic conductivity results in its excellent electrochemical kinetics. Ex situ XRD and XPS tests prove the intercalation-type mechanism of BiO and BiOSe as well as the superior electrochemical reversibility of BiOSe compared to BiO. Furthermore, the H+/Zn2+ co-insertion mechanism of BiOSe is revealed. This makes BiOSe to have low discharge plateaus of 0.38/0.68 V, a high reversible capacity of 182 mA h g-1 at 0.1 A g-1, and a long cyclic life of 500 cycles at 1 A g-1. Besides, the BiOSe//MnO2 "rocking chair" zinc-ion battery offers a high capacity of ≈90 mA h g-1 at 0.2 A g-1. This work provides a reference for turning commercial material into high-performance anode for "rocking chair" zinc-ion batteries.

Construction and Interfacial Modification of a ß-PbSnF4 Electrolyte with High Intrinsic Ionic Conductivity for a Room-Temperature Fluoride-Ion Battery.

Solid-state fluoride-ion batteries (FIBs) attract significant attention worldwide because of their high theoretical volume, energy density, and high safety. However, the large interfacial resistance caused by the point-point contact between the electrolyte and the electrode seriously impedes their further development. Using liquid-phase therapy to construct a conformal interface is a good choice to eliminate the influence of inadequate contact between the electrode and the electrolyte. In this study, a ß-PbSnF4 solid-state electrolyte with high room-temperature ionic conductivity is prepared, and a trace amount of the liquid electrolyte (LE) between the electrode and the electrolyte is introduced in order to minimize the interfacial resistance and enhance the cycle life. The Allen-Hickling simulations show that the introduction of an interfacial wetting agent (LE) can significantly reduce the energy barrier of charge transfer and mass transfer processes at the interface and reciprocate FIBs an enhanced interfacial reaction kinetics. As a result, the initial discharge capacity of the fabricated FIBs is 210.5 mAh g-1 and the capacity retention rate is 82.6% after 50 cycles at room temperature, while the initial discharge capacity of the unmodified battery is only 170.9 mAh g-1 and the capacity retention rate is 22.1% after 50 cycles. Therefore, interfacial modification with a trace amount of LE provides a significant exploration for the improvement of FIB performances.

Lithium-Ion Conductor Li2ZrO3-Coated Primary Particles To Optimize the Performance of Li-Rich Mn-Based Cathode Materials.

A lithium-rich manganese-based cathode material (LRMC) is currently considered as one of the most promising next-generation materials for lithium-ion batteries, which has received much attention, but the LRMC still faces some key scientific issues to break through, such as poor rate capacity, rapid voltage, capacity decay, and low first coulomb efficiency. In this work, homogeneous Li2ZrO3 (LZO) was successfully coated on the surface of Li1.2Mn0.54Ni0.13Co0.13O2 (LRO) by molten salt-assisted sintering technology. Li2ZrO3 has good chemical and electrochemical stability, which can effectively inhibit the side reaction between electrode materials and electrolytes and reduce the dissolution of transition metal ions. Thus, the as-prepared LRO@LZO composites are expected to improve the cycling performance. It can be found that the discharge specific capacity of LRO is 271 mAh g-1 at 0.1 C, and the capacity retention rate is still 93.7% after 100 cycles at 1 C. In addition, Li2ZrO3 is an excellent lithium-ion conductor, which is prone to increasing the lithium-ion transfer rate and improving the rate capacity of LRO. Therefore, this study provides a new solution to improve the structure stability and electrochemical performance of LRMCs.

Identification of Vitis vinifera MYB transcription factors and their response against grapevine berry inner necrosis virus.

BACKGROUND: The myeloblastosis (MYB) superfamily is the largest transcription factor family in plants that play diverse roles during stress responses. However, the biotic stress-responsive MYB transcription factors of the grapevine have not been systematically studied. In China, grapevine berries are often infected with the grapevine berry inner necrosis virus (GINV), which eventually reduces the nutritional quality and commodity value. RESULTS: The present study identified and characterized 265 VvMYB or VvMYB-related genes of the "Crimson seedless" grapevine. Based on DNA-binding domain analysis, these VvMYB proteins were classified into four subfamilies, including MYB-related, 2R-MYB, 3R-MYB, and 4R-MYB. Phylogenetic analysis divided the MYB transcription factors into 26 subgroups. Overexpression of VvMYB58 suppressed GINV abundance in the grapevine. Further qPCR indicated that among 41 randomly selected VvMYB genes, 12 were induced during GINV infection, while 28 were downregulated. These findings suggest that VvMYB genes actively regulate defense response in the grapevine. CONCLUSION: A deeper understanding of the MYB TFs engaged in GINV defense response will help devise better management strategies. The present study also provides a foundation for further research on the functions of the MYB transcription factors.

Ni-doped Bi2O2CO3 nanosheet with H+/Zn2+ co-insertion for "rocking chair" zinc-ion battery.

Developing insertion-type anode is key to advancing "rocking chair" zinc-ion batteries, though there are few reported insertion-type anodes. Herein, the Bi2O2CO3 is a high-potential anode, with a special layered structure. A one-step hydrothermal method was used to prepare Ni-doped Bi2O2CO3 nanosheet, and also a free-standing electrode consisting of Ni-Bi2O2CO3 and CNTs was designed. Both cross-linked CNTs conductive networks and Ni doping improve charge transfer. Ex situ tests (XRD, XPS, TEM, etc.) reveal the H+/Zn2+ co-insertion mechanism of Bi2O2CO3 and that Ni doping improves its electrochemical reversibility and structural stability. Therefore, this optimized electrode offers a high specific capacity of 159 mAh g-1 at 100 mA g-1, a suitable average discharge voltage of ≈0.400 V, and a long-term cycling stability of 2200 cycles at 700 mA g-1. Besides, the Ni-Bi2O2CO3//MnO2 "rocking chair" zinc-ion battery (based on the total mass of cathode and anode) delivers a high capacity of ≈100 mAh g-1 at 50.0 mA g-1. This work provides a reference for designing high-performance anode in zinc-ion batteries.

BiOIO3@Zn3(PO4)2·4H2O Heterojunction with Fast Ionic Diffusion Kinetics for Long-Life "Rocking-Chair" Zinc Ion Batteries.

Increasing insertion host materials are developed as high-performance anodes of "rocking-chair" zinc ion batteries. However, most of them show unsatisfactory rate capabilities. Herein, layered BiOIO3 is reported as an excellent insertion host and a zinc ion conductor, i.e., Zn3(PO4)2·4H2O (ZPO), is introduced to construct a BiOIO3@ZPO heterojunction with a built-in electric field (BEF). Both ZPO and a BEF obviously enhance Zn2+ transfer and storage, which is proven by theoretical calculations and experimental studies. The conversion-type mechanism of BiOIO3 is revealed through ex situ characterizations. The optimized electrode exhibits a high reversible capacity of 130 mAh g-1 at 0.1 A g-1, a low average discharge voltage of 0.58 V, an ultrahigh rate performance with 68 mAh g-1 at 5 A g-1 (52% of capacity at 0.1 A g-1), and an ultralong cyclic life of 6000 cycles at 5 A g-1. Significantly, the BiOIO3@ZPO//Mn3O4 full cell shows a good cyclic life of 67 mAh g-1 over 1000 cycles at 0.1 A g-1. This work provides a new insight into the design of anodes with excellent rate capability.

Using "Age and Total-PSA" as the Main Indicators: The Results of Taizhou Integrated Prostate Screening (No 2).

The aim of the study was to analyze population-based prostate cancer (PCa) screening and the incidence of PCa among males ≥50 years of age residing in the Luqiao district of Taizhou, China. From October to December 2020, male residents ≥50 years of age were screened for serum total prostate-specific antigen (total-PSA). If t-PSA re-test levels persisted above 4 µg/L, subjects underwent further noninvasive examinations, including digital rectal examination or multiparameter magnetic resonance imaging (mpMRI) of the prostate. Subjects underwent prostate biopsy of pathological tissue based on t-PSA and mpMRI results. A total of 3524 (49.1%) residents participated in this PCa screening study. In total, 285 (8.1%) subjects exhibited t-PSA levels ≥4.0 µg/L and 112 (3.2%) underwent noninvasive examinations. Forty-two (1.2%) residents underwent prostate biopsy, of which 16 (0.45%) were diagnosed with PCa. Of those diagnosed with PCa, three (19%) had localized PCa (cT1-cT2N0M0), six (37%) had locally advanced PCa (cT3a- cT4N0-1M0), and seven (44%) had advanced metastatic PCa (M1). Unfortunately, 3477 (48.5%) residents did not participate in the study, mainly due to lack of awareness of PCa based on feedback from local health centers. Age and t-PSA were used as primary screening indicators and, when further combined with mpMRI and prostate biopsy, confirmed the diagnosis of PCa among participating residents. Although this was a relatively economical and convenient screening method, education and knowledge should be further enhanced to increase the participation rate in PCa screening programs.