A decade of atrial fibrillation ablation : Shifts in patient characteristics and procedural outcomes.

BACKGROUND: Over the past decade, radiofrequency catheter ablation (RFCA) of atrial fibrillation (AF) has evolved into a frequently performed procedure. The aim of this study was to monitor changes in patient characteristics, procedural characteristics, outcomes and complications over the past 10 years. METHODS: All consecutive patients who underwent primary RFCA treatment of AF in the University Medical Center Utrecht from 2005-2015 were included. In all patients, the primary ablation strategy was pulmonary vein (PV) antrum isolation without additional substrate modification. Baseline patient and procedure characteristics, and 1­year follow-up data of 975 patients were prospectively collected. RESULTS: In 2005, 73.4% of patients suffered from paroxysmal AF, which decreased to 45.3% in 2014. Mean age increased from 54 ± 9 to 61 ± 10 years and CHA2DS2-VASc score ≥2 from 18 to 40.6%. History of AF decreased significantly from 7 to 4 years. Mean procedure duration was 237 ± 53 min in 2005 and 163 ± 41 min in 2014. Fluoroscopy time significantly decreased from 41 ± 17 to 19 ± 8 min and total radiation exposure from 465 (263-687) to 210 (118-376) mGy. One-year success remained similar (2005: 55.6%, 2014: 54.8%), as did the amount of PV reconnection observed during redo procedures. Due to a marked reduction in vascular complications and moderate PV stenosis, the total complication rate decreased significantly. CONCLUSION: Over the past decade, AF ablation has increasingly been performed in older patients with persistent AF and more comorbidity. Moreover, it has been performed earlier after AF diagnosis. Although several performance parameters, such as procedure duration and complication rate, improved, 1­year single procedure success remained unchanged.

Measure twice, cut once: pitfalls in the diagnosis of supraventricular tachycardia.

In atrioventricular nodal and atrioventricular reentrant tachycardia, the relative timing of atrial and ventricular activation may sometimes be very similar, even during electrophysiological studies, and this may lead to an erroneous diagnosis and inappropriate treatment. As examples, we describe two cases that were recently referred to our hospital for a second opinion and treatment of paroxysmal supraventricular tachycardia. In both, the original diagnosis of the referring centres was commontype atrioventricular nodal reentrant tachycardia. Catheter ablation in those centres was unsuccessful. During our electrophysiological studies, however, an atrioventricular reentrant tachycardia was demonstrated, using a concealed accessory pathway for retrograde conduction in both patients. The accessory atrioventricular connection was successfully ablated and on follow-up both patients remained free of symptoms without medication. These findings illustrate the importance of complete electrophysiological analysis even for apparently simple supraventricular arrhythmias. (Neth Heart J 2010;18:78-84.).

Contrast-enhanced MRA and 3D visualization of pulmonary venous anatomy to assist radiofrequency catheter ablation.

In pulmonary vein isolation as a treatment for atrial fibrillation the proximal part of the pulmonary veins is catheterized. A protocol for preinterventional assessment of pulmonary vein anatomy was developed, based on contrast-enhanced magnetic resonance angiography (MRA) in combination with three-dimensional visualization to tailor periprocedural angiography. The results allow for assessment of the number, morphology, and location of the ostia of the pulmonary veins, as well as complicating anatomical variations, such as common trunks and aberrant courses.

Isolation of residual sinus node during catheter ablation for the treatment of inappropriate sinus tachycardia.

Inappropriate sinus tachycardia is an unusual arrhythmia that is difficult to treat. To date, catheter ablation has concentrated on modifying the sinus node to attain rate control. We describe a patient where sinoatrial block was created by radiofrequency ablation for the treatment of inappropriate sinus tachycardia.

Technique of pulmonary vein isolation by catheter ablation.

In selected patients with atrial fibrillation, the fibrillation episodes may be initiated by single or short bursts of ectopy often originating from one or more pulmonary veins (PVs). Therefore, electrical isolation of these veins by catheter ablation is currently being explored as a treatment modality for patients with paroxysmal and even more permanent types of atrial fibrillation. At present, two different techniques are used: 1) selective ablation of electrical connections between left atrium and myocardial sleeves inside the PVs; and 2) contiguous encircling lesions around and outside the PV ostia. With both techniques, moderate to high success rates have been reported with a limited follow-up duration. Both types of procedure are very complex and require a highly skilful team. With the variable anatomy of the PVs, non-invasively acquired angiographic images may serve as a roadmap for catheter manipulation. Modern three-dimensional catheter navigation techniques can be applied to facilitate accurate catheter positioning with limited fluoroscopic exposure. Experimental and clinical research is needed to define patient selection criteria.

Increased dispersion and shortened refractoriness caused by verapamil in chronic atrial fibrillation.

OBJECTIVES: The objective was to assess the effect ofverapamil on atrial fibrillation (AF) cycle length and spatial dispersion of refractoriness in patients with chronic AF. BACKGROUND: Previous studies have suggested that verapamil prevents acute remodeling by AF. The effects of verapamil in chronic AF are unknown. METHODS: During electrophysiologic study in 15 patients with chronic AF (duration >1 year), 12 unipolar electrograms were recorded from right atrial free wall, right atrial appendage and coronary sinus, along with monophasic action potential recordings from the right atrial appendage. The mean fibrillatory interval at each atrial recording site was used as an index for local refractoriness. Dispersion of refractoriness was calculated as the standard deviation of all local mean fibrillatory intervals expressed as a percentage of the overall mean fibrillatory interval. After baseline measurements, verapamil (0.075 mg/kg intravenous in 10 min) was infused and the measurements were repeated. RESULTS: After administration ofverapamil, mean fibrillatory intervals shortened by a mean of 16.6 +/- 3.3 ms (p < 0.001) at the right free wall, 15.0 +/- 3.5 ms (p < 0.001) at the appendage and 17.1 +/- 3.2 ms (p < 0.01) in the coronary sinus. Monophasic action potential duration decreased by 15.9 +/- 4.0 ms (p < 0.01). Dispersion of refractoriness increased in all patients from 3.8 +/- 0.8 to 5.1 +/- 1.8 (p < 0.001). A strong correlation between mean fibrillatory intervals and action potential duration was found, both before and after verapamil. CONCLUSIONS: Verapamil caused shortening of refractoriness and increase in spatial dispersion of refractoriness in patients with chronic AF. This implies that verapamil is not useful in reversing the remodeling process in these patients.

Ventricular tachycardia as a complication of atrial flutter ablation.

A 61-year-old woman with dilated cardiomyopathy, who previously underwent successful radiofrequency catheter ablation for atrial flutter, developed monomorphic ventricular tachycardia (VT). The site of VT origin was the inferobasal right ventricle adjacent to the previous atrial isthmus ablation area. The most likely mechanism for the VT was scar-related reentry, the scar being the result of previous radiofrequency lesions in the atrial isthmus. The VT was successfully ablated.

Identification of the substrate of atrial vulnerability in patients with idiopathic atrial fibrillation.

BACKGROUND: Experimental studies have shown that atrial fibrillation (AF) causes remodeling, which facilitates AF perpetuation. AF may also, however, occur in patients without remodeling and underlying structural cardiac disease. The substrate for enhanced vulnerability in these patients is unknown. METHODS AND RESULTS: We studied 43 patients without structural heart disease: 18 patients with documented sporadic paroxysmal AF and 25 control patients without AF. In each patient, a decapolar catheter was positioned against the right atrial free wall, and a quadripolar catheter was positioned in the right atrial appendage. Unipolar electrograms were recorded. Atrial vulnerability was assessed according to an increasingly aggressive stimulation protocol. Mean local fibrillatory interval (FI) was used as an index of local refractoriness. Spatial dispersion of refractoriness was assessed through the calculation of the coefficient of dispersion (CD), which was defined as the SD of mean local FI expressed as a percentage of the mean FI. In the AF group, AF was induced with a single extrastimulus in 16 of 18 patients; the CD was 5.4+/-2.6, and the mean FI was 164+/-29 ms. In the control group, AF could be induced only with more aggressive pacing in 23 of the 25 patients; the CD was 1.4+/-0.7 (P<0.0001), and the mean FI was 175+/-26 ms (NS). CONCLUSIONS: Patients with idiopathic AF showed increased dispersion of refractoriness, which may be the substrate for the observed enhanced inducibility and spontaneous occurrence of AF.

Reduction of radiation exposure in the cardiac electrophysiology laboratory.

The purpose of this study was to determine the effects of various protective measures on patient and operator radiation dose levels in catheter ablation procedures. Catheter ablation procedures are associated with significant radiation levels. The patient's skin and operator radiation levels were measured (1) at baseline, (2) after primary beam filtration by 0.3-mm copper sheet and 2-mm aluminium plate and implementation of the LocaLisa system, and (3) after reduction of the left anterior oblique fluoroscopic pulse rate and installation of a lead glass screen. Additionally, a comparative analysis of radiation exposure levels was performed in the seven Dutch catheter ablation centers. Filtration of both primary beams resulted in a more than two-fold reduction in patient skin dose. Together with the LocaLisa system, this resulted in a six-fold reduction in patient and operator dose. As expected, lowering of the left anterior oblique pulse rate from 25 to 12.5 Hz reduced the corresponding patient skin dose with a factor 2 while the lead-glass protection caused an extra factor 2 reduction for the operator. Large differences were observed between fluoroscopy systems used for catheter ablation in the Netherlands. Depending on patient body mass and fluoroscopy system, patient skin dose varied between 0.2 and 8.4 Gy/hour. Proper measures may allow for a significant reduction of patient and operator radiation exposure in catheter ablation procedures. The large influence of body mass and equipment on patient's skin dose requires a more direct monitoring of skin dose than total fluoroscopy time.

LocaLisa: new technique for real-time 3-dimensional localization of regular intracardiac electrodes.

BACKGROUND: Estimation of the 3-dimensional (3D) position of ablation electrodes from fluoroscopic images is inadequate if a systematic lesion pattern is required in the treatment of complex arrhythmogenic substrates. METHODS AND RESULTS: We developed a new technique for online 3D localization of intracardiac electrodes. Regular catheter electrodes are used as sensors for a high-frequency transthoracic electrical field, which is applied via standard skin electrodes. We investigated localization accuracy within the right atrium, right ventricle, and left ventricle by comparing measured and true interelectrode distances of a decapolar catheter. Long-term stability was analyzed by localization of the most proximal His bundle before and after slow pathway ablation. Electrogram recordings were unaffected by the applied electrical field. Localization data from 3 catheter positions, widely distributed within the right atrium, right ventricle, or left ventricle, were analyzed in 10 patients per group. The relationship between measured and true electrode positions was highly linear, with an average correlation coefficient of 0.996, 0.997, and 0.999 for the right atrium, right ventricle, and left ventricle, respectively. Localization accuracy was better than 2 mm, with an additional scaling error of 8% to 14%. After 2 hours, localization of the proximal His bundle was reproducible within 1.4+/-1.1 mm. CONCLUSIONS: This new technique enables accurate and reproducible real-time localization of electrode positions in cardiac mapping and ablation procedures. Its application does not distort the quality of electrograms and can be applied to any electrode catheter.

Accuracy of the LocaLisa system in catheter ablation procedures.

Estimation of the 3-dimensional (3D) position of ablation electrodes from fluoroscopic images is inadequate in the ablation of complex arrhythmogenic substrates. We developed a new technique for real-time 3D localization of intracardiac electrodes. Regular catheter electrodes are used as sensors for a high-frequency transthoracic electrical field, which is applied via standard skin electrodes. We investigated localization accuracy by comparing measured and true interelectrode distances between the tip and the 10th electrode of a decapolar catheter, and the tip and the 4th electrode of a quadripolar catheter during catheter ablation procedures. Long-term stability was analyzed by localization of the proximal His bundle before and after slow pathway ablation. Accuracy achieved with the 54-mm distance between the two outer electrodes of the decapolar catheters was 101% +/- 15%, 95% +/- 10%, and 97% +/- 8% in the right atrium, right ventricle, and left ventricle, respectively. During catheter ablation procedures, the measured distance between the tip and 4th electrode of the mapping catheter was 100% +/- 15% in atrial flutter, 100% +/- 12% in slow pathway ablation, and 100% +/- 14% in ablations for left ventricular tachycardia. After 2 hours, localization of the proximal His bundle was reproducible within 1.4 +/- 1.1 mm. The LocaLisa technique allows for reproducible, real-time nonfluoroscopic 3D visualization of standard mapping and ablation catheters and is sufficiently accurate for the creation of linear radiofrequency lesions. The freedom of catheter choice makes the LocaLisa system an invaluable tool in catheter mapping and ablation procedures.

The LETR-Principle: a novel method to assess electrode-tissue contact in radiofrequency ablation.

INTRODUCTION: Stable electrode-tissue contact is crucial for successful radiofrequency ablation of cardiac tachyarrhythmias. In this in vitro study, a custom-made radiofrequency generator was used to evaluate the correlation between tip temperature response to a minimal radiofrequency power delivery (Low Energy Temperature Response: LETR-Principle) and electrode-tissue contact as well as lesion size. METHODS AND RESULTS: A battery-powered radiofrequency generator (LETR-Box, 500 kHz, 0.1 to 0.3 W) could measure the temperature increase at the tip electrode with 0.01 degrees C accuracy. The device was tested in vitro using isolated porcine ventricular tissue. For various electrode-tissue settings (i.e., 0 to 0.89 N contact force), the temperature increase (deltaT) due to 0.1-W power delivery for 10 seconds was recorded. Subsequently, for the same electrode-tissue contact, a temperature-controlled radiofrequency ablation was performed (70 degrees C target temperature, 50-W maximum output, 30 sec). Thereafter, the lesion size was measured histologically. To prove the safety of the applied LETR-Principle, the tissue was inspected microscopically after continuous radiofrequency power delivery of 0.3 W for 1 hour with high contact pressure (1.33 N). The delivery of 0.1-W radiofrequency power resulted in an average deltaT of 0.18 degrees +/- 0.13 degrees C. During temperature-controlled radiofrequency ablation, the tip temperature was 59 degrees +/- 8.5 degrees C, resulting in a lesion depth of 4.8+/-0.6 mm. The correlation coefficient between deltaT and contact force was 0.97 and 0.81, respectively, for lesion depth. No lesion was microscopically visible after power delivery of 0.3 W for 1 hour with 1.33 N contact pressure. CONCLUSION: The LETR-Principle safely indicates electrode-tissue contact and lesion depth under in vitro conditions and can be useful for catheter positioning during radiofrequency ablation procedures.

Inverse relationship between electrode size and lesion size during radiofrequency ablation with active electrode cooling.

BACKGROUND: Clinical efficacy has driven the use of larger electrodes (7F, length > or =4 mm) for radiofrequency ablation, which reduces electrogram resolution and causes variability in tissue contact depending on electrode orientation. With active cooling, ablation electrode size may be reduced. The purpose of this study was to examine the effect of electrode length on tissue temperature and lesion size with saline irrigation used for active cooling. METHODS AND RESULTS: In 11 anesthetized dogs, the thigh muscle was exposed and bathed with heparinized canine blood. A 7F ablation catheter with a 2- or 5-mm irrigated tip electrode was positioned perpendicular or parallel to the thigh muscle. Radiofrequency current was delivered at constant voltage (50 V) for 30 seconds during saline irrigation (20 mL/min) to 148 sites. Tissue temperature at depths of 3.5 and 7 mm and lesion size were measured. In the perpendicular electrode-tissue orientation, radiofrequency applications at 50 V with the 2-mm electrode compared with the 5-mm electrode resulted in lower power at 50 V (26 versus 36 W) but higher tissue temperatures, larger lesion depth (8.0 versus 5.4 mm), and greater diameter (12.4 mm versus 8.4 mm). Also, in the parallel orientation, overall power was lower with the 2-mm electrode (25 versus 33 W), but tissue temperatures were higher and lesions were deeper (7.3 versus 6.9 mm). Lesion diameter was similar (11.1 versus 11.3 mm) for both electrodes. CONCLUSIONS: The smaller electrode resulted in transmission of a greater fraction of the radiofrequency power to the tissue and resulted in higher tissue temperature, larger lesions, and lower dependency of lesion size on the electrode orientation.

Origin of heat-induced accelerated junctional rhythm.

INTRODUCTION: The application of high-frequency current to the AV junctional area results in a temperature rise in the myocardium and may cause accelerated junctional rhythm (AJR). The aim of the study was to characterize heat-induced AJR in an in vitro animal model. METHODS AND RESULTS: Studies were performed in isolated perfused pig and rabbit hearts. Using a small heating probe, we could induce AJR from a discrete area located in the middle of the triangle of Koch, which was smaller than the area from which RF energy application could elicit AJR. Histology showed that the heat-sensitive area was located over, or close to, the compact AV node. It did not correspond with the areas where double potentials were found or with the site(s) of earliest atrial activation during VA conduction. Microelectrode recordings revealed that AJR arose in nodal-type cells. Heat increased the slope of the phase 4 depolarization and shortened the action potential duration. Two types of AJR were observed: the first one was regular and the second one showed irregularity in the intervals. Interaction of multiple foci and the presence of conduction block between the foci and the His bundle caused the irregularity of the His-His intervals during the second type of AJR. CONCLUSION: AJR observed during heat and RF application in the AV nodal area results from the effect of heat on AV nodal cells with underlying pacemaker activity. The heat-sensitive area is located over, or very close to, the compact AV node.

Why a large tip electrode makes a deeper radiofrequency lesion: effects of increase in electrode cooling and electrode-tissue interface area.

INTRODUCTION: Increasing electrode size allows an increase in radiofrequency lesion depth. The purpose of this study was to examine the roles of added electrode cooling and electrode-tissue interface area in producing deeper lesions. METHODS AND RESULTS: In 10 dogs, the thigh muscle was exposed and superfused with heparinized blood. An 8-French catheter with 4- or 8-mm tip electrode was positioned against the muscle with a blood flow of 350 mL/min directed around the electrode. Radiofrequency current was delivered using four methods: (1) electrode perpendicular to the muscle, using variable voltage to maintain the electrode-tissue interface temperature at 60 degrees C; (2) same except the surrounding blood was stationary; (3) perpendicular electrode position, maintaining tissue temperature (3.5-mm depth) at 90 degrees C; and (4) electrode parallel to the muscle, maintaining tissue temperature at 90 degrees C. Electrode-tissue interface temperature, tissue temperature (3.5- and 7.0-mm depths), and lesion size were compared between the 4- and 8-mm electrodes in each method. In Methods 1 and 2, the tissue temperatures and lesion depth were greater with the 8-mm electrode. These differences were smaller without blood flow, suggesting the improved convective cooling of the larger electrode resulted in greater power delivered to the tissue at the same electrode-tissue interface temperature. In Method 3 (same tissue current density), the electrode-tissue interface temperature was significantly lower with the 8-mm electrode. With parallel orientation and same tissue temperature at 3.5-mm depth (Method 4), the tissue temperature at 7.0-mm depth and lesion depth were greater with the 8-mm electrode, suggesting increased conductive heating due to larger volume of resistive heating because of the larger electrode-tissue interface area. CONCLUSION: With a larger electrode, both increased cooling and increased electrode-tissue interface area increase volume of resistive heating and lesion depth.

Effects of intracavitary blood flow and electrode-target distance on radiofrequency power required for transient conduction block in a Langendorff-perfused canine model.

OBJECTIVES: We sought to quantify the effects of electrode-target distance and intracavitary blood flow on radiofrequency (RF) power required to induce transient conduction block, using a Langendorff-perfused canine ablation model. BACKGROUND: Given the thermally mediated nature of RF catheter ablation, cooling effects of intracavitary blood flow and electrode-target distance will influence lesion extension and geometry and electrophysiologic effects. METHODS: In eight Langendorff-perfused canine hearts, the right ventricular free wall was opened, and the right bundle branch (RBB) carefully localized by multielectrode activation mapping. The right atrium was paced at cycle length of 500 ms. Proximal and distal electrodes were attached at the endocardial aspect of the RBB, and the perfused heart was submerged in heparinized blood at 37 degrees C. A standard 4-mm tip ablation electrode was positioned at a constant contact pressure of 5 g between the two electrodes at the site of maximal RBB potential (0 mm) and 2 and 4 mm distant from this site along a line perpendicular to the RBB. RF pulses (500 kHz) were delivered for 30 s at 0.5-W increments until transient bundle branch block. In four hearts, intracavitary flow was simulated by directing a 30-cm/s jet of blood parallel to the septum at the ablation site, and the protocol was repeated to assess the effects on power required for block. In one heart, the effect of variable flow was assessed (0, 15 and 30 cm/s). RESULTS: An exponential distance-related increase was seen in power required for block, from 1.8 +/- 0.9 W (mean +/- SD) at 0 mm to 5.4 +/- 1.1 W at 4 mm. In the presence of 30-cm/s flow, an increase to 3.9 +/- 0.8 W at 0 mm and 13.1 +/- 2.4 W at 2 mm was seen. At 4 mm, coagulum formation invariably occurred before block could be induced. For 15-cm/s flow, less power was required: 3 and 7 W at 0 and 2 mm, respectively. CONCLUSIONS: Increasing the ablation electrode-target distance causes an exponential increase in power required for conduction block; this relation is profoundly influenced by intracavitary flow. Given the geometry of endomyocardial RF lesions, these findings are particularly relevant for directly subendocardial ablation targets.

Thermal latency in radiofrequency ablation.

BACKGROUND: Progression of unintentionally induced atrioventricular delay is occasionally observed directly after termination of radiofrequency delivery in the vicinity of the atrioventricular node. We postulated that the application of a radiofrequency pulse may result in a tissue temperature rise that continues after the pulse. METHODS AND RESULTS: Using the thigh muscle preparation, 5-, 10-, 20-, and 30-second pulses were applied as 30 to 40 W via a standard 4-mm tip electrode with 10-g contact pressure. Forty-one undisturbed pulses were delivered while recording intramural temperatures at 2-, 4-, and 7-mm depth. Maximal "thermal latency" was observed with the shortest pulse duration and at greatest depth. With 5-second applications, tissue temperature at 7-mm depth peaked 11.6 seconds after termination of radiofrequency delivery and stayed above end-of-pulse value as long as 34.5 seconds after the pulse. The additional rise in tissue temperature was 2.9 degrees C. If only recording within the lesion border zone were considered, the duration of latency was maximal with 10-second pulses: an additional gain in tissue temperature of 3.4 degrees C was observed 6.4 seconds after the pulse while tissue temperature stayed above end-of-pulse value during 18.3 seconds. CONCLUSIONS: With relatively short applications, tissue temperature continues to rise after termination of radiofrequency delivery. This "thermal latency" may result in lesion growth after the pulse and may so explain the incidentally observed progression of conduction block after short pulses in the vicinity of the atrioventricular node. It also may explain the apparent discrepancy between lesion growth rate and intramural temperature rise studies.

Effects of heating with radiofrequency power on myocardial impulse conduction: is radiofrequency ablation exclusively thermally mediated?

INTRODUCTION: Although it is generally accepted that radiofrequency (RF) ablation causes exclusively thermally mediated effects, it has never been proved. METHODS AND RESULTS: In a previous report, temperatures required to induce conduction block in superfused canine epicardial ventricular myocardium were identified by exposure to heated superfusate: 50.3 degrees +/- 1.1 degrees C and 53.6 degrees +/- 0.6 degree C for transient and permanent block, respectively. In the present study, heating was performed using RF power in an otherwise identical model. Nine preparations from four dogs were used. A 1-cm diameter electrode was placed beneath the center of each preparation for RF delivery. Incisions were made to create a conductive isthmus over the ablation electrode. Preparations were paced to one side of the isthmus and electrograms recorded from the center of the isthmus and to either side. Temperature was measured using a miniature thermocouple located just below the epicardial surface, adjacent to the recording electrode in the heated zone. RF was delivered for 30 seconds at 5-minute intervals with increments in power per episode causing increments in temperature of approximately 2 degrees C. Temperature during pulses at which transient block occurred was 50.7 degrees +/- 3.0 degrees C; temperature at 30 seconds of heating in pulses leading to permanent block was 58.0 degrees +/- 3.4 degrees C. CONCLUSION: These findings provide evidence suggesting that the electrophysiologic effects of RF ablation are exclusively thermally mediated and are otherwise unrelated to the dissipation of high-frequency current.

Prevention of mandibular fractures by using constructional design principles. II. A tension strength test on beagle mandibles with two different types of segmental resections.

The tension strength of mandibular halves of beagle dogs, with two different types of segmental resections, was studied. It was found that the radius of the posterior resection corner is of utmost importance in reducing the risk of mandibular fractures.