Enhancing catalyst stability: Immobilization of Cu-Fe catalyst in sodium alginate matrix for methyl orange removal via Fenton-like reaction.

This study aims to enhance the stability and effectiveness of heterogeneous catalysts in Fenton-like reactions, explicitly addressing the acidity limitations inherent in traditional Fenton processes. Copper-iron was synthesized through co-precipitation, and a catalyst bead was produced from hydrogel formation. X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS) confirm phases in the bimetallic Copper-iron, aligning with the intended composition. Modification with alginate led to reduced metal leaching compared to the bare bimetallic counterpart, as confirmed by atomic absorption spectroscopy (AAS). Additionally, Fourier-transform infrared spectroscopy (FTIR) revealed the deactivation of alginate through the disappearance of carboxyl groups, indicating the depolymerization of the catalyst bead. Under the suggested conditions (Methyl Orange concentration of 25 mg/L, initial solution pH of 7, 2 g/L catalyst loading, concentration of hydrogen peroxide 100 mM in a 120-min reaction time), the catalyst demonstrated remarkable decolorization efficiency of Methyl Orange, achieving 97.67 %. Further highlighting its practicality, the catalyst exhibited outstanding reusability over four cycles under identical conditions, showcasing robust immobilization capabilities and sustained performance. Notably, the catalyst's magnetic properties facilitated easy separation using an external magnet. In conclusion, the developed catalyst beads offer a solution with high reusability, magnetic separability, and reduced iron leaching. The advantageous characteristics underscore its potential as a heterogeneous catalyst for wastewater treatment applications, warranting further exploration under practical conditions.

A pH-dependent and charge selective covalent organic framework for removal of dyes from aqueous solutions.

A novel imine-linked COF is synthesized by the condensation of 2,4,6-tris(4-aminophenyl)-1,3,5-triazine (TAPT) and 2-hydroxy-5-methoxyisophthalaldehyde (HMIPA) under solvothermal conditions. This COF adsorbs preferentially the neutral dye Neutral Red (NR) over the positively charged dye Methylene Blue (MB) at pH 7, and the negatively charged Methyl Orange (MO) over the positively charged Methylene Blue (MB) at pH 3. The maximum adsorption capacities (qe) obtained within very short times (11-60 min) under optimized conditions were 108, 185 and 429 mg.g-1 for the MB, MO, and NR dyes, respectively. These adsorptions obey the Langmuir isotherm and pseudo-second-order kinetics. The prepared TAPT-HMIPA-COF is used successfully for the removal of the dyes from real water and treated wastewater samples. The adsorption data, BET, FTIR, and zeta potential measurements show that the electrostatic, π-π stacking and hydrogen bond interactions are responsible for the adsorption of organic dyes on the surface of the prepared COF. Due to recyclability, high capacity and efficiency for the adsorption of positive, negative and neutral organic dyes, this COF can be considered promising for simultaneous removal of various dyes from aqueous solutions at adjusted pHs.

Activated Carbon Prepared from Waste Coffee Grounds: Characterization and Adsorption Properties of Dyes.

Spent coffee grounds (SCGs) have great potential as a useful, value-added biological material. In this context, activated carbon (AC) was prepared from SCGs by an activation process using H3PO4 at 600 °C in the air and used as an adsorbent for the azo dye AO7, a model molecule for dye colorants found in textile industry effluents. X-ray diffraction, SEM and BET revealed that the AC was predominantly amorphous, consisting of a powder of 20-100 µm particles with mesopores averaging 5.5 nm in pore size. Adsorption kinetics followed a pseudo-second-order law, while the Langmuir model best fitted the experimental isotherm data (maximum capacity of 119.5 mg AO7 per AC g). The thermodynamic parameters revealed that adsorption was endothermic and spontaneous. All the characterizations indicated that adsorption occurred by physisorption via mainly π-π interactions. The best experimental removal efficiency optimized by means of a Box-Behnken design and response surface methodology was 98% for an initial AO7 concentration of 20 mg·L-1 at pH 7.5 with a dose of 0.285 g·L-1 of AC and a contact time of 40 min. These results clearly show that activated carbon prepared from SCGs can be a useful material for efficiently removing organic matter from aqueous solutions.

Nanosheet BiOBr Modified Rock Wool Composites for High Efficient Oil/Water Separation and Simultaneous Dye Degradation by Activating Peroxymonosulfate.

The development of superlyophobic materials in liquid systems, enabling synchronous oil/water separation and dye removal from water, is highly desirable. In this study, we employed a novel superwetting array-like BiOBr nanosheets anchored on waste rock wool (RW) fibers through a simple neutralization alcoholysis method. The resulting BiOBr/RW fibers exhibited superoleophilic and superhydrophilic properties in air but demonstrated underwater superoleophobic and underoil superhydrophobic characteristics. Utilizing its dual superlyophobicity, the fiber layer demonstrated high separation efficiencies and flux velocity for oil/water mixtures by prewetting under a gravity-driven mechanism. Additionally, the novel BiOBr/RW fibers also exhibited excellent dual superlyophobicity and effective separation for immiscible oil/oil systems. Furthermore, the BiOBr/RW fibers could serve as a filter to continuously separate oil/water mixtures with high flux velocity and removal rates (>93.9%) for water-soluble dye rhodamine B (RhB) simultaneously by directly activating peroxymonosulfate (PMS) in cyclic experiments. More importantly, the mechanism of simultaneous oil/water separation and RhB degradation was proposed based on the reactive oxygen species (ROS) quenching experiments and electron paramagnetic resonance (EPR) analysis. Considering the simple modified process and the waste RW as raw material, this work may open up innovative, economical, and environmentally friendly avenues for the effective treatment of wastewater contaminated with oil and water-soluble pollutants.

Quick methylene blue dye elimination via SDS-Ag nanoparticles catalysts.

Methylene blue dye, being toxic, carcinogenic and non-biodegradable, poses a serious threat for human health and environmental safety. The effective and time-saving removal of such industrial dye necessitates the use of innovative technologies such as silver nanoparticle-based catalysis. Utilizing a pulsed Nd:YAG laser operating at the second harmonic generation of 532 nm with 2.6 J energy per pulse and 10 ns pulse duration, Ag nanoparticles were synthesized via an eco-friendly method with sodium dodecyl sulphate (SDS) as a capping agent. Different exposure times (15, 30, and 45 min) resulted in varying nanoparticle sizes. Characterization was achieved through UV-Vis absorption spectroscopy, scanning electron microscopy (SEM) imaging, and energy dispersive X-ray (EDX). Lorentzian fitting was used to model nanoparticle size, aligning well with SEM results. Mie's theory was applied to evaluate the absorption, scattering, and extinction cross-sectional area spectra. EDX revealed increasing Ag and carbon content with exposure time. The SDS-caped AgNPs nanoparticles were tested as catalyst for methylene blue degradation, achieving up to 92.5% removal in just 12 min with a rate constant of 0.2626 min-1, suggesting efficient and time-saving catalyst compared to previously reported Ag-based nanocatalysts.

Rapid eco-friendly selective dye removal using modified chitosan-based sponges: Synthesis, characterization, and application.

The ongoing challenge of water scarcity persists alongside a concerning rise in water pollution driven by population expansion and industrial development. As a result, urgent measures are imperative to address the pressing need for a clean and sustainable water supply. In this study, a sustainable and green approach was utilized to prepare four chitosan-based sponges from a chemically modified chitosan with different alkyl chains in aqueous medium and at room temperature. The resulting sponges displayed excellent stability in water with outstanding dye removal efficiency. The adsorption capacity was associated with the alkyl chain length incorporated to the polymer backbone. All sponges displayed a high adsorption capacity of methyl orange (MO) ranges between 238 and 380 mg g-1, while a low capacity were obtained for methylene blue (MB) and Rhodamine B (RB). Competitive adsorption experiments were conducted on binary and ternary mixtures to assess the selective removal of MO from a mixture of dyes in which the separation factor was found to be ranging between 1.6 and 32. The adsorption kinetics isotherms of all sponges followed the pseudo-second-order, and the Langmuir model was found to be more suitable than the Freundlich for the adsorption of MO on the sponges. The chitosan-based sponges showed stable performance, robustness and reusability over 5 adsorption-desorption cycles, indicating their great potential for water treatment applications.

Chitosan extraction from Amanita phalloides: yield, crystallinity, degree of deacetylation, azo dye removal and antibacterial properties.

Chitosan, a biopolymer obtained from chitin, is known for its remarkable adsorption abilities for dyes, drugs, and fats, and its diverse array of antibacterial characteristics. This study explores the extraction and characterization of chitosan from the mycelium of Amanita phalloides. The moisture content, ash content, water binding capacity, fat binding capacity, and degree of deacetylation of the extracted chitosan were determined. The chitosan exhibited a high yield of 70%, crystallinity of 49.07%, a degree of deacetylation of 86%, and potent antimicrobial properties against both Gram-negative and Gram-positive bacteria. The study also examined the adsorption capabilities of chitosan to remove methylene blue (MB) dye by analysing specific factors like pH, reaction time, and MB concentration using the response surface model. The highest degree of MB dye removal was 91.6% at a pH of 6, a reaction time of around 60 min and an initial dye concentration of 16 ppm. This experimental design can be applied for chitosan adsorption of other organic compounds such as dyes, proteins, drugs, and fats.

Superlong Metal-organic Framework Nanowire Fabricated via Steam-assisted Conversion.

1D nanomaterials have attracted great attention due to their outstanding anisotropic and linear structures. A facile method is developed to fabricate 1D copper metal-organic framework nanowires (Cu-MOF-NW) through steam-assisted conversion from Cu-MOF precursors. During the steam-assisted conversion, Cu-MOF precursor gradually dissolves in methanol steam, and then recrystallized into Cu-MOF-NW, which shows high aspect ratio of about 600 and identical crystal structure of MOF-74. As-prepared Cu-MOF-NW with multiscale porous structure can effectively remove cationic dyes even in dye mixture. Moreover, Cu-MOF-NW, as an ideal template, is calcined to form Cu nanoparticle-doped carbon nanofiber with maintaining its 1D morphology, which shows excellent electrocatalytic activity for the non-enzymatic sensing of glucose.

Kinetics and thermodynamics studies of nickel manganite nanoparticle as photocatalyst and fuel additive.

In this study, nickel manganite (NiMn2O4) nanoparticles were prepared using a hydrothermal method and examined its potential as a photocatalyst for the Acid Green 25 (AG-25) dye degradation. The nanoparticles were subjected to structural analysis using X-ray diffraction (XRD) and morphological analysis using scanning electron microscopy (SEM). The study examined the kinetics and thermodynamics of degradation processes that are catalyzed by photocatalysis. To ascertain their effect on dye degradation, several parameters, such as catalyst dose, H2O2 concentration, and temperature, were investigated. With a temperature of 315 K in a pseudo-first-order kinetic reaction, a 0.3 M H2O2 concentration, 0.05 mg/mL catalyst dose, and a promising removal efficiency of 96 % was achieved by the NiMn2O4 NPs in 40 min. Thermodynamic analysis revealed the spontaneous and entropy-driven nature of catalytic degradation, progressing favorably at elevated temperatures. Additionally, the NiMn2O4 NPs were applied as a fuel additive to analyze its influence on combustion and the physical characteristics of the modified fuel. The modified fuel demonstrated exceptional catalytic efficiency, emphasizing the potential of the NiMn2O4 NPs as an effective additive.

Preparation and Application of Responsive Nanocellulose Composites.

Cellulose nanofibrils/poly(N-Isopropylacrylamide) semi-interpenetrating networks (MMCNF-PNAs) were synthesized using an in situ fabrication (semi-IPN). The polymerization of N-isopropylacrylamide (NIPAM) (free radical) was conducted in the presence of magnetic modified cellulose nanofibrils (MMCNFs). The adsorption behaviors and surface morphology of the synthesized adsorbents were investigated systematically. The adsorption behaviors of the as-prepared MMCNF-PNA towards methylene blue (MB, as the model contaminant) dye was studied, and the optimal adsorption conditions were also studied. The adsorption processes could be well fitted using pseudo-second-order and Elovich kinetic models. Meanwhile, Langmuir and Freundlich isotherm models were used to fit the adsorption which occurred at 25, 37 and 65 °C. The corresponding results showed that the Freundlich isotherm model fitted the adsorption process better, indicating that the dye's adsorption happened via heterogeneous adsorptive energies on the prepared MMCNF-PNAs. Their desorption and reusability were also studied to verify magnetic responsivity. To sum up, MMCNF-PNAs are promising magnetic and thermal stimuli-responsive adsorbents, showing a controlled adsorption/desorption process.

The Utilization of Chicken Egg White Waste-Modified Nanofiber Membrane for Anionic Dye Removal in Batch and Flow Systems: Comprehensive Investigations into Equilibrium, Kinetics, and Breakthrough Curve.

This study investigated the use of chicken egg white (CEW) waste immobilized on weak acidic nanofiber membranes for removing the anionic acid orange 7 (AO7) dye in batch and continuous flow modes. Different experiments were conducted to evaluate the effectiveness of CEW-modified nanofiber membranes for AO7 removal, focusing on CEW immobilization conditions, adsorption kinetics, and thermodynamics. The CEW-modified nanofiber membrane (namely NM-COOH-CEW) exhibited a maximum AO7 adsorption capacity of 589.11 mg/g within approximately 30 min. The Freundlich isotherm model best represented the equilibrium adsorption data, while the adsorption kinetics followed a pseudo-second-order rate model. Breakthrough curve analysis using the Thomas model and the bed depth service time (BDST) model showed that the BDST model accurately described the curve, with an error percentage under 5%. To investigate AO7 elution efficiency, different concentrations of organic solvents or salts were tested as eluents. The NM-COOH-CEW nanofiber membrane exhibited promising performance as an effective adsorbent for removing AO7 dye from contaminated water.

Novel amino-ethyl carboxymethyl cellulose crosslinked ampholyte hydrogel development for Methyl orange removal from waste water.

In the modern era, with the rapid growth of various industries, the issues of energy crisis and environmental pollution have garnered increasing attention. One significant source of industrial pollution is printing and dyeing wastewater. This wastewater often contains dyes that have aromatic structures and azo groups, such as Methyl orange (MO), which are both toxic and difficult to degrade. If these dyes are released into the wastewater stream without any treatment, they can have adverse effects on ecological balance and human health. Therefore, it is crucial to identify suitable treatment strategies to efficiently remove dyes from wastewater systems before discharge. In this study, the Methyl orange (MO) azo dye has been removed from dyes-contaminated wastewater, for the first time, using a novel amino-ethyl carboxymethyl cellulose crosslinked ampholyte hydrogel (AECMC). Different characterization methods, including FTIR, TGA, and DSC were used to characterize the generated AECMC compounds. The water absorption and cationic exchange capacities were assessed. Factors affecting the MO anions adsorption including MO concentration, adsorption pH, temperature, time, adsorbent dose, and agitation speed have been investigated. Moreover, the kinetics of the adsorption process was assessed by the use of three models: pseudo-first-order, Pseudo-second-order, and Elovich. Moreover, the mechanism of the adsorption process was monitored using the Intraparticle diffusion and Boyd models. Additionally, the adsorption isotherm was examined using established models such as Langmuir, Freundlich, and Temkin isotherms. The thermodynamic characteristics of the MO adsorption process have been investigated at various adsorption temperatures using the Van't Hoff model. The results obtained from the study indicate that the process of MO adsorption adhered to the Pseudo-second-order kinetic model, the Langmuir isotherm model was found to be applicable, and spontaneous and exhibited an endothermic character. In conclusion, the developed novel amino-ethyl carboxymethyl cellulose crosslinked ampholyte hydrogels (AECMC) have successive in the removal of the MO anionic dye from contaminated wastewater.

Superabsorbent ZnO/rubber-based hydrogel composite for removal and photocatalytic degradation of methylene blue.

A superabsorbent hydrogel was prepared by the free-radical copolymerization of natural rubber (NR) latex with poly(acrylic acid) (PAA) at NR loadings up to 50 wt%. An NR/PAA hydrogel containing 40 wt% of NR (NR-40) had a water absorption capacity of 214 g/g (21,400 %) of its dry weight. The compressive modulus increased 512 % and sample integrity was improved due to the physical entanglement of NR chains. NR-40 hydrogel removed 97 % of methylene blue (MB) from the aqueous solution in 1 h (at initial concentrations of 10-1000 mg/L) and produced a maximum removal of 1191 mg MB/g of hydrogel at an initial MB concentration of 4500 mg/L. The adsorption of MB was an endothermic process. Fourier transform infrared spectroscopy indicated that hydrogen bonding and electrostatic interaction drove the process. After the in-situ incorporation of ZnO into NR-40, absorbed energy from sunlight generated active species that could photocatalytically degrade adsorbed MB in the hydrogel matrix. The scavenger tests indicated that superoxide radical anions and hydroxyl radicals were the main species for this process. The hydrogel composite material showed good stability and could be regenerated and reused over 10 cycles, degrading >80 % of the adsorbed dye. This novel natural-based hydrogel provides double functions of adsorption and photodegradation of toxic dyes without the requirement of chemicals and a separation process.

A state-of-the-art review of metal oxide nanoflowers for wastewater treatment: Dye removal.

Dye wastewater consists of high solids concentrations, heavy metals, minor contaminants, dissolved chemical oxygen demand, and microorganisms. Nanoflowers are nanoparticles that resemble flowers when viewed at a microscopic level. Inorganic metal oxide nanoflowers have been discovered to be a potential source for overcoming this situation. Their flower-like features give them a higher surface area to volume ratio and porosity structure, which can absorb a significant amount of dye. The metal oxide nanoflower synthesized from different synthesis methods is used to compare which one is cost-effective and capable of generating a large scale of nanoflower. This review has demonstrated outstanding dye removal efficiency by applying inorganic nanoflowers to dye removal. Since both adsorption and photocatalytic reactions enhance the dye degradation process, complete dye degradation could be achieved. Meanwhile, the inorganic metal oxide nanoflowers' exemplary reusability characteristics with negligible performance drop further prove that this approach is highly sustainable and may help to save costs. This review has proven the momentum of obtaining high dye removal efficiency in wastewater treatment to conclude that the metal oxide nanoflower study is worth researching.

Synthesis of zeolite from industrial wastes: a review on characterization and heavy metal and dye removal.

Increasing world population, urbanization, and industrialization have led to an increase in demand in production and consumption, resulting in an increase in industrial solid wastes and pollutant levels in water. These two main consequences have become global problems. The high Si and Al content of solid wastes suggests that they can be used as raw materials for the synthesis of zeolites. In this context, when the literature studies conducted to obtain synthetic zeolites are evaluated, it is seen that hydrothermal synthesis method is generally used. In order to improve the performance of the hydrothermal synthesis method in terms of energy cost, synthesis time, and even product quality, additional methods such as alkaline fusion, ultrasonic effect, and microwave support have been developed. The zeolites synthesized by different techniques exhibit superior properties such as high surface area and well-defined pore sizes, thermal stability, high cation exchange capacity, high regeneration ability, and catalytic activity. Due to these specific properties, zeolites are recognized as one of the most effective methods for the removal of pollutants. The toxic properties of heavy metals and dyes in water and their carcinogenic effects in long-term exposure pose a serious risk to living organisms. Therefore, they should be treated at specified levels before discharge to the environment. In this review study, processes including different methods developed for the production of zeolites from industrial solid wastes were evaluated. Studies using synthetic zeolites for the removal of high levels of health and environmental risks such as heavy metals and dyes are reviewed. In addition, EPMA, SEM, EDX, FTIR, BET, AFM, and 29Si and 27Al NMR techniques, which are characterization methods of synthetic zeolites, are presented and the cation exchange capacity, thermodynamics of adsorption, effect of temperature, and pH are investigated. It is expected that energy consumption can be reduced by large-scale applications of alternative techniques developed for zeolite synthesis and their introduction into the industry. It is envisaged that zeolites synthesized by utilizing wastes will be effective in obtaining a green technology. The use of synthesized zeolites in a wide variety of applications, especially in environmental problems, holds great promise.

Photodecoration of tungsten oxide nanoparticles onto eggshell as an ultra-fast adsorbent for removal of MB dye pollutant.

Nowadays, the use of natural wastes and adsorbents along with their modification by simple and new methods based on metal oxides to remove dye pollutants has been the focus of many researchers. In this study, for the first time, simple and low-cost modification of eggshell (EGS) with tungsten oxide (WO3) based on the photochemical modification method as a green, ultra-fast, cost-effective, and biodegradable adsorbent is reported to remove of methylene blue (MB) dye pollutant. The EGS modified by WO3 was investigated by EDX, EDX mapping, XRD, FE-SEM, and UV-Vis Diffuse Reflectance (DRS) analyses. The obtained results show that the modified EGS by WO3 has more than ten times (78.5%) the ability to remove MB dye pollutant within 3 min compared to bare EGS (11%). Various parameters including dye pollutant pH, dye concentration, adsorbent dosage, and reusability of the WO3/EGS adsorbent for removal of MB dye pollutant were investigated and the result show that the adsorbent capacity of WO3/EGS is 1.64 mg g-1. EGS adsorbent The synthesis of WO3/EGS adsorbent with a novel photochemical method as a fast and very cheap adsorbent with excellent efficiency can be a promising alternative adsorbent for various purposes in removing dye pollutants from water environments.

Effect of nano-TiO2 size and utilization ratio on the performance of photocatalytic concretes; self-cleaning, fresh, and hardened state properties.

In this study, photocatalysis technology was used to reduce water pollution. Decolorization of Reactive Black 5 using nano-TiO2 (NT) as a photocatalyst was investigated by adsorption and degradation experiments. Effects of NT particle size and utilization ratio on the time-dependent flow performance, compressive-flexural strength, and Bohme abrasion resistance of cementitious systems were investigated. In addition to the NT-free control mixture, a total of six photocatalytic self-cleaning mortar mixtures (PSCM) were prepared using NT in two different particle sizes (28 and 38 nm) and three different ratios (0.5%, 1%, and 1.5%). The PSCM sample containing 38 nm NT exhibited superior performance in terms of photocatalytic properties compared to the 28 nm state. It was observed that the flow performance of PSCM mixtures with NT substitution is adversely affected regardless of the NT type. Mixtures containing NT with a lower particle size (28 nm) had higher compressive and flexural strengths.

Facile Fabrication of Porous Adsorbent with Multiple Amine Groups for Efficient and Selective Removal of Amaranth and Tartrazine Dyes from Water.

The development of an advanced dye adsorbent that possesses a range of beneficial characteristics, such as high adsorption capacity, swift adsorption kinetics, selective adsorption capability, and robust reusability, remains a challenge. This study introduces a facile method for fabricating an amine-rich porous adsorbent (ARPA), which is specifically engineered for the adsorptive removal of anionic dyes from aqueous solutions. Through a comprehensive assessment, we have evaluated the adsorption performance of ARPA using two benchmark dyes: amaranth (ART) and tartrazine (TTZ). Our findings indicate that the adsorption process reaches equilibrium in a remarkably short timeframe of just 20 min, and it exhibits an excellent correlation with both the Langmuir isotherm model and the pseudo-second-order kinetic model. Furthermore, ARPA has demonstrated an exceptional maximum adsorption capacity, with values of 675.68 mg g-1 for ART and 534.76 mg g-1 for TTZ. In addition to its high adsorption capacity, ARPA has also shown remarkable selectivity, as evidenced by its ability to selectively adsorb TTZ from a mixed dye solution, a feature that is highly desirable for practical applications. Beyond its impressive adsorption capabilities, ARPA can be efficiently regenerated and recycled. It maintains a high level of original removal efficiency for both ART (76.8%) and TTZ (78.9%) even after five consecutive cycles of adsorption and desorption. Considering the simplicity of its synthesis and its outstanding adsorption performance, ARPA emerges as a highly promising material for use in dye removal applications. Consequently, this paper presents a straightforward and feasible method for the production of an effective dye adsorbent for environmental remediation.

Adsorption and antibacterial studies of a novel hydrogel adsorbent based on ternary eco-polymers doped with sulfonated graphene oxide developed from upcycled plastic waste.

A novel ternary blended polymer composed of cost-effective and readily available polymers was synthesized using poly (vinyl alcohol) (PVA), iota carrageenan (IC), and poly (vinyl pyrrolidone) (PVP). Sulfonated graphene oxide (SGO), prepared from recycled drinking water bottles, was utilized as a doping agent. Varying amounts (1-3 wt%) were combined into the polymer matrix. The produced hydrogel film was examined as a potential adsorbent hydrogel film for the removal of methylene blue (MB) and Gentamicin sulfate (GMS) antibiotic from an aqueous solution. The experimental results demonstrate that the presence of SGO significantly increased the adsorption efficiency of PVA/IC/PVP hydrogel film. The antimicrobial tests revealed that the PVA/IC/PVP-3% SGO hydrogel film exhibited the most potent activity against all the tested pathogenic bacteria. However, the adsorption results for MB and GMS showed that the addition of 3 wt% SGO resulted in a removal percentage that was a two fold increase in the removal percentage compared with the undoped PVA/IC/PVP hydrogel film. Furthermore, the response surface methodology (RSM) model was utilized to examine and optimize several operating parameters, including time, pH of the solution, and initial pollutant concentration. The adsorption kinetics were better characterized by the pseudo-second-order kinetics model. The composite film containing 3 wt% SGO had a maximum adsorption capacity of 606 mg g-1 for MB and 654 mg g-1 for GMS, respectively. The generated nanocomposite hydrogel film demonstrated promising potential for application in water purification systems.

Preparation of MWCNT/CoMn2O4 nanocomposite for effectual degradation of picric acid via peroxymonosulfate activation.

In recent years, using nanomaterials based on multi-wall carbon nanotubes (MWCNT) through the activation of peroxymonosulfate (PMS) has attracted more attention to the degradation of organic pollutants. This research presented a new route for the synthesis of MWCNT/CoMn2O4 nanocomposite for the degradation of picric acid using advanced oxidation processes (AOPs). Firstly, CoMn2O4 nanoparticles were prepared and then loaded on MWCNT using ultrasonic waves. The results of various analyzes confirmed the successful loading of nanoparticles on carbon nanotubes. As the degradation process proceeds through oxidation processes, the high electronic conductivity of MWCNT and the active sites of Mn and Co in the nanocomposite play an essential role in activating PMS to generate reactive oxygen species (ROS). An investigation of the reaction mechanism in different conditions showed that the highest speed of picric acid decomposition in the presence of nanocomposite (98%) was in 47 min. However, the scavenger test showed that HO· and SO4·- radicals are more important in the degradation process. Meanwhile, the results showed that removing picric acid using MWCNT/CoMn2O4 was more effective than CoMn2O4 alone and confirmed the interaction effect of MWCNT nanotubes with AB2O4 nanocatalyst.