Design of suspension culture system with bubble sparging for human induced pluripotent stem cells in a plastic fluid.

Bubble sparging has been used to supply oxygen to large-scale bioreactor systems. However, sparged bubbles cause cell death by rupturing due to shear stress, and the foam layer carries a risk of contamination. Large-scale culture of human induced pluripotent stem cells (hiPSCs) is required for manufacturing, but hiPSCs show high sensitivity to shear stress, and also, aseptic processing is important for their expansion. In this study, a culture system with bubble sparging for hiPSC proliferation was designed using a plastic fluid as a culture medium. The rising bubble velocity in the plastic fluid decreased and was lower than that in a Newtonian fluid when the time interval between bubbles generation, Δt, was greater than 0.14 s. Under this condition, aggregate distribution in the plastic fluid was maintained without liquid flow. Although large aeration induced aggregate coalescence and growth inhibition, the apparent specific growth rate at Δt > 0.14 s increased with an increase in the aeration rate, and the maximum value was similar to that of the conventional suspension culture in a stirred bioreactor system. The gas hold-up in the plastic fluid was higher than that in a Newtonian fluid because of the lower rising bubble velocity, which leads to the suppression of bubble sparging. Therefore, our results indicated that using a plastic fluid leads to a more efficient oxygen supply without agitation in a spatial-temporal phase-transition culture system.

Phase equilibria, physical and rheological properties of extracellular polymeric substances in the aqueous urea solutions at different temperatures and concentrations.

Extracellular polymeric substances (EPS) were extracted from aerobic granule sludge (AGS) using 8 M aqueous urea solution. It seems that the knowledge of these multi-component systems properties and the ability to predict their phase behavior is necessary for the extraction units design as well as process optimization. In this regard, water activity using the Dynamic Vapor Sorption (DVS) method, viscosity and shear stress, pH, and conductivity were measured at 283.15-343.15 K and 0.0108 to 0.0375 wt fraction of EPS. The salting effects in ternary systems assessed and the results were interpreted in terms of solute-water and solute-solute interactions. It was found these systems were not semi-ideal and except at 283.15 K, had a positive deviation from ideal solution behavior and only at this temperature as the optimum extraction temperature, the salting-in effect was observed for each concentration of EPS. The ternary solutions behave like pseudo-plastic fluids while aqueous urea solution is a Newtonian fluid. Increasing the temperature causes a decrease and increase in pH and conductivity of ternary solutions, respectively and the presence of EPS increases those of 8 M urea solution significantly.

Protection of human induced pluripotent stem cells against shear stress in suspension culture by Bingham plastic fluid.

Suspension culture is an important method used in the industrial preparation of pluripotent stem cells (PSCs), for regenerative therapy and drug screening. Generally, a suspension culture requires agitation to keep PSC aggregates suspended and to promote mass transfer, but agitation also causes cell damage. In this study, we investigated the use of a Bingham plastic fluid, supplemented with a polysaccharide-based polymer, to preserve PSCs from cell damage in suspension culture. Rheometric analysis showed that the culture medium gained yield stress and became a Bingham plastic fluid, after supplementation with the polymer FP003. A growth/death analysis revealed that 2 days of aggregate formation and 2 days of suspension in the Bingham plastic medium improved cell growth and prevented cell death. After the initial aggregation step, whereas strong agitation (120 rpm) of a conventional culture medium resulted in massive cell death, in the Bingham plastic fluid we obtained the same growth as the normal culture with optimal agitation (90 rpm). This indicates that Bingham plastic fluid protected cells from shear stress in suspension culture and could be used to enhance their robustness when developing a large-scale.

CFD and Optimization Study of Frictional Pressure Drop Through Bends.

BACKGROUND: The non-Newtonian pseudoplastic liquid flow through different types of the bend is more complicated compared to the simple straight pipe as the bends are associated with various curve geometry. Bends have wide application in bioengineering, biotechnology and biomedical such as study biofluids, blood rheology study, the design of medical equipment like equipment measuring the cholesterol etc. Method: The papers deal with the estimation of loss coefficient and frictional pressure drop of Newtonian and non-Newtonian pseudoplastic fluid flow through the different bend of 0.0127 m diameter pipe geometry using commercially available CFD software fluent 6.3. We revised all patents relating to the pipe flow through different types of bend. The present study also deals with the efficient application of Genetic Algorithm (GA) for optimization of frictional pressure drop. Laminar Non-Newtonian Power law model is used for Sodium Carboxy Methyl Cellulose (SCMC) solution to solve the continuity and the momentum equations numerically. Generalized input-output correlation has been developed by Gene Expression Programming (GEP) using Matlab. RESULTS: The above-mentioned algorithm is used to predict and optimize the pressure drop. It has been found that, the process exhibit the minimum pressure drop across the bend under optimum condition (Angle = 133.160, Concentration = 0.2 Kg/m3 and velocity = 0.53 m/s). The effect of flow rate, bend angle, fluid behaviour on static pressure and pressure drop has also been investigated. CONCLUSION: From the study, it can be concluded that the developed GA model has a good agreement with the CFD model. The software predicted data might be used to solve various industrial problems and also to design different equipment.

Mechanism of memory effect of paste which dominates desiccation crack patterns.

When a densely packed colloidal suspension, called a paste, behaves as plastic fluid, it can remember the direction of its motion it has experienced, such as vibrational motion and flow. These memories kept in paste can be visualized as the morphology of crack patterns that appear when the paste is dried. For example, when a paste remembers the direction of vibrational motion, all primary desiccation cracks propagate in the direction perpendicular to the direction of the vibrational motion that the paste has experienced. On the other hand, when a paste remembers the direction of flow motion, all primary cracks propagate along the flow direction. To find out the mechanism of memory effect of vibration, we perform experiments to rewrite memory in paste by applying additional vibration to the paste along a different direction before the paste is dried. By investigating the process of rewriting memory in paste, we find the competitive phenomena between quasi-linear effect and nonlinear effect, which were studied in each theoretical model based on residual tension theories. That is, at the initial stage of the memory-imprinting process of the vibrational motion, the mechanism predicted by the quasi-linear analysis based on residual tension theory holds, but, as the paste is vibrated repeatedly, the mechanism shown by the nonlinear analysis gradually come to play a dominant role in the memory effect.This article is part of the theme issue 'Statistical physics of fracture and earthquakes'.