Colorimetric detection of Cr(VI) in water using tetramethyl benzidine (TMB) as an indicator.

Hexavalent chromium (CrVI) poses a serious risk to both human and environment health. Hence, a simple, robust, and efficient analytical method must be developed to monitor the presence of Cr(VI) in the environment. The current investigation concentrated on the colorimetric detection of Cr(VI) using TMB as indicator in the presence of H2O2. The study found that Cr(VI) reacts with H2O2 to generate hydroxyl radicals which oxidize TMB in a concentration dependent manner. Under optimized conditions, the method obtained a good linearity range (0.025-0.5 mg/L, r2 = 0.9944) with LOD and LOQ of 0.009 mg/L and 0.029 mg/L, respectively. The technique was further improved by the addition of EDTA in the sample preparation protocol to reduce the false positive result by the presence of ions like Cu2+, Fe3+, etc. The study recorded improved Cr(VI) recoveries (81.73-111.40 %) at different fortification levels (0.1-0.5 mg/L). Under optimized conditions, the EDTA added method obtained a good linear response (r2 = 0.9952) with a detection limit of 0.023 mg/L which is less than the prescribed limits by WHO (0.05 mg/L) and US EPA (0.1 mg/L) for drinking water. The developed analytical method is very simple without use of any nanomaterial and the results with natural water samples show that it has the potential for real-time detection of Cr(VI) in the environment.

Qualitative and quantitative water investigation of Erin-Ijesha (Olumirin) Waterfall, Erin-Ijesha, Nigeria.

This study focused on the assessment of water quality in Erin-Ijesha (Olumirin) Waterfall, a prominent natural attraction in southwestern Nigeria. The physiochemical parameters, heavy metal concentrations, and bacteriological characteristics were examined in the upstream, midstream, and downstream sections, to ensure the resource quality and safety from harm. The results revealed notable variations in water quality. The pH, Total Dissolved Solids, Electrical Conductivity, and Temperature were highest in the midstream while Total Hardness, Alkalinity, salinity, Chloride, sulphate, Phosphate, Nitrate, Calcium, and Magnesium were highest in the downstream section. The physicochemical parameters were within the acceptable limits of World Health Organization (WHO), United States Environmental Protection Agency (USEPA), and the Standard Organization of Nigeria (SON) standards, except the pH, temperature, and Total Hardness were higher than the acceptable limits of 6.5-8.5, <25 °C or >50 °C and 50 mg/L in all the sections. Iron was above the WHO, USEPA, and SON permissible limits of 3.0 mg/L in all the sections of the river while there was no indication of copper, lead, and cadmium. Bacterial contamination, particularly the presence of E. coli, exceeded recommended safety thresholds. The Total Bacterial Count (TBC) exceeded safety limits by 0.1 million cfu/mL in the downstream. The mean of the parameters was higher in some instances, and sometimes lower than the values in the various sections of the river. A significant relationship existed between most physical, chemical, and bacteriological parameters at p < 0.01. The appraisal of water quality in Olumirin Waterfalls emphasizes the need for proactive measures to ensure water safety, preserve ecosystems, and promote responsible water resource management.

Visual arsenic detection in environmental waters: Innovating with a naked-eye biosensor for universal application.

Arsenic contamination in environmental water sources poses a significant threat to human health, necessitating the development of sensitive and accessible detection methods. This study presents a multidimensional optimization of a bacterial biosensor for the susceptible and deoxyviolacein (DV)-based visual detection of arsenic. The research involved screening six different arsenic resistance (ars) operons and optimizing the genetic circuit to minimize background noise. Introducing an arsenic-specific transport channel enhanced the sensor's sensitivity to 1 nM with a quantitative range from 0.036 to 1.171 µM. The pigment-based biosensor offers a simple colorimetric approach for arsenic detection without complex instrumentation. The preferred biosensor demonstrated characteristics of anti-chelating agent interference, consistently quantified As(III) concentrations ranging from 0.036 to 1.171 µM covering the World Health Organization (WHO) drinking water limit. Innovatively, it effectively detects arsenic in seawater within a linear regression range of 0.071 to 1.125 µM. The biosensor's selectivity for arsenic was confirmed, with minimal cross-response to group 15 metals. Our naked-eye biosensor offers a novel approach for the rapid, on-site detection of arsenic in various water sources. Its simplicity, cost-effectiveness, and versatility make it a valuable tool for environmental monitoring and public health initiatives.

Flow analysis-solid phase extraction system and UHPLC-MS/MS analytical methodology for the determination of antiviral drugs in surface water.

An automated flow analysis-solid phase extraction (FA-SPE) system and methodology of ultra-high-performance liquid chromatography with tandem mass spectrometry (UHPLC-MS/MS) analysis were developed for the determination of selected antiviral drugs (acyclovir, amantadine, rimantadine, and oseltamivir) in water samples. The proposed FA-SPE approach enables the integration of various extraction stages and elimination of the sample evaporation step and offers individual customisation of SPE parameters, inter alia sample, and eluate flow rate and volume. Using the developed FA-SPE procedure, e.g. a 100-fold preconcentration of the target analytes in 1 h was achieved. A method for chromatographic analysis was also developed to determine the selected antiviral drugs in combination with the use of the FA-SPE system. The developed FA-SPE UHPLC-MS/MS method was validated including the determination of linearity of analytical graphs, limits of detection (5.5-99.9 pg mL-1) and quantification (18.3-329.8 pg mL-1), intra-day (1.8-8.3%) and inter-day (3.0-9.2%) precision, recovery (95.6-105.3%), and matrix effects (- 12.9 to 13.2%). The proposed method was successfully applied to analyse tap, drinking, and river water samples, revealing the presence of amantadine at a concentration of 40.1 pg mL-1 in one sample. The environmental impact of the developed FA-SPE sample preparation procedure was also assessed using the AGREEprep metric tool and compared with five other literature methods, achieving the most sustainable outcome.

Effect of short-term sample storage and preparatory conditions on losses of 18 per- and polyfluoroalkyl substances (PFAS) to container materials.

There is a lack of agreement on a suitable container material for per- and polyfluoroalkyl substances (PFAS) analysis, particularly at trace levels. In this study, the losses of 18 short- and long-chain (C4-C10) PFAS to commonly used labware materials (high-density polyethylene (HDPE), polypropylene (PP), polystyrene (PS), polypropylene co-polymer (PPCO), polyethylene terephthalate (PET), polytetrafluoroethylene (PTFE), and glass were investigated. The influence of sample storage and preparation conditions, i.e., storage time, solvent composition, storage temperatures (4 °C and 20 °C), and sample agitation techniques (shaking and centrifugation) on PFAS losses to the container materials were investigated. The results showed higher losses for most of the considered PFAS (up to 50.9%) in 100% aqueous solutions after storage for 7 days regardless of the storage temperature compared to those after 3 days. Overall, the order of losses to different materials varied for individual PFAS, with the highest losses of long-chain PFAS observed to PP and HDPE after 7-day storage at room temperature. The addition of methanol to aqueous PFAS solutions reduced the losses of long-chain PFAS to all tested materials. The use of sample centrifugation and shaking did not influence the extent of losses for most of the PFAS in 80:20 water:methanol (%, v/v) to container materials except for 8:2 fluorotelomer sulfonic acid (8:2 FTS), 9-chlorohexadecafluoro-3-oxanone-1-sulfonic acid (9Cl-PF3ONS), perfluorodecanoic acid (PFDA) and 4:2 fluorotelomer sulfonic acid (4:2 FTS). This study demonstrates lower losses of both long- and short-chain PFAS to glass and PET. It also highlights the need for caution when deciding on sample preparatory steps and storage during the analysis of PFAS.

Portable IC system enabled with dual LED-based absorbance detectors and 3D-printed post-column heated micro-reactor for the simultaneous determination of ammonium, nitrite and nitrate.

BACKGROUND: The on-site and simultaneous determination of anionic nitrite (NO2-) and nitrate (NO3-), and cationic ammonium (NH4+), in industrial and natural waters, presents a significant analytical challenge. Toward this end, herein a 3D-printed micro-reactor with an integrated heater chip was designed and optimised for the post-column colorimetric detection of NH4+ using a modified Berthelot reaction. The system was integrated within a portable and field deployable ion chromatograph (Aquamonitrix) designed to separate and detect NO2- and NO3-, but here enabled with dual LED-based absorbance detectors, with the aim to provide the first system capable of simultaneous determination of both anions and NH4+ in industrial and natural waters. RESULTS: Incorporating a 0.750 mm I.D. 3D-printed serpentine-based microchannel for sample-reagent mixing and heating, the resultant micro-reactor had a total reactor channel length of 1.26 m, which provided for a reaction time of 1.42 min based upon a total flow rate of 0.27 mL min-1, within a 40 mm2 printed area. The colorimetric reaction was performed within the micro-reactor, which was then coupled to a dedicated 660 nm LED-based absorbance detector. By rapidly delivering a reactor temperature of 70 °C in just 40 s, the optimal conditions to improve reaction kinetics were achieved to provide for limits of detection of 0.1 mg L-1 for NH4+, based upon an injection volume of just 10 µL. Linearity for NH4+ was observed over the range 0-50 mg L-1, n = 3, R2 = 0.9987. The reactor was found to deliver excellent reproducibility when included as a post-column reactor within the Aquamonitrix analyser, with an overall relative standard deviation below 1.2 % for peak height and 0.3 % for peak residence time, based upon 6 repeat injections. SIGNIFICANCE: The printed post-column reactor assembly was integrated into a commercial portable ion chromatograph developed for the separation and detection of NO2- and NO3-, thus providing a fully automated system for the remote and simultaneous analysis of NO2-, NO3-, and NH4+ in natural and industrial waters. The fully automated system was deployed externally within a greenhouse facility to demonstrate this capability.

Simultaneous and on-line detection of organic and heavy metal components in water using a novel nebulization-assisted injection plasma ionization triple quadruple mass spectrometry instrument.

BACKGROUND: The global release of organic and heavy metal components into natural water bodies is a major concern for the environment and human health. The assessment of water quality relies on analyzing organic and heavy metal components qualitatively and quantitatively. Real-time identification of organic and metal components in water systems requires different analytical techniques due to varying measurement requirements. Thus, on-line detecting both organic compounds and heavy metals in ambient water systems simultaneously using a single instrumentation setup presents a significant challenge. RESULTS: In this study, an analytical technique of nebulization-assisted injection plasma ionization mass spectrometry (NI-PIMS) was developed. This novel method enables the simultaneous detection of heavy metals and organic compounds in water system with high sensitivity, which has been demonstrated by the limit of quantification (LOQ) values below 1.0 µg/L for the three sterols (Enrofloxacin, ciprofloxacin, and clenbuterol) and three heavy metals (Pb, Ba, and Cd). Moreover, the method was successfully applied to rapidly analyze real water samples from urban and rural areas in China. The analytical results are available in less than 0.5 min, and only a few microliters of sample are required for each analysis. SIGNIFICANCE AND NOVELTY: As far as we know, this is the first report of on-line simultaneous analysis of organic compounds and heavy metals in a water system using a single mass spectrometry instrument. Compared to traditional methods, NI-PIMS demonstrates higher efficiency, sensitivity, no or lower sample preparation, and less sample consumption. The advancement and widespread use of this technology are expected to enhance the effectiveness of mass spectrometers, broaden the applications, and play an important role in complex sample analysis in fields such as atmospheric science, environmental science, and earth science.

Fabrication of molecularly imprinted carbon nanotubes integrating ionic liquids for efficient detection of perfluoroalkyl carboxylic acid in environmental water.

It is extremely significant while challenging to accurately detect low-levels of perfluoroalkyl carboxylic acid compounds (PFCAs) in environmental water. Herein, adopting perfluorotetradecanoic acid as the dummy template, selective molecularly imprinted composites (CNTs@ILs@MIPs) grafted carbon nanotubes integrating hydrophilic ionic liquids were successfully prepared via surface imprinting and dummy-template imprinting techniques. The obtained CNTs@ILs@MIPs were applied as selective extraction adsorbent for specifically extract PFCAs in environmental water coupled with gas chromatography-mass spectrometry quantification. Detailed studies were conducted on the main preparation parameters and extraction conditions. The CNTs@ILs@MIPs displayed excellent adsorptivity, and the established method exhibited low LODs (0.60-1.64 ng L-1), wide linearity with R2 above 0.9994, and satisfactory adsorption recoveries (80.5-112.5%) for seven PFCAs. This proposed method provides a new applicable approach for the detection of targeted pollutants in environmental water by utilizing the high affinity and recognition ability of molecularly imprinted carbon nanotube functional materials modified with ionic liquids.

Magnetic Poly(Amidoamine) Dendrimer for the Dispersive Solid Phase Extraction of Nitrophenols from Environmental Water Samples.

A fast and simple dispersive solid phase extraction method is described for nitrophenols determination in water samples by using gas chromatography-nitrogen phosphorous detector. Firstly, the Poly(amidoamine) grafted Fe3O4 magnetic nanoparticles were synthesized in different generations by successive addition of butyl acrylate and ethylenediamine. After characterization, the prepared dendrimer was utilized as an adsorbent for magnetic solid phase extraction of 2-nitrophenol, 3-nitrophenol, and 4-nitrophenol to benefit large number of surface amine interaction sites. The effects of the different parameters influencing the sample preparation efficiency were investigated. The proposed method showed linearity in the ranges of 0.04-700 and 0.05-700 µg/dm3 for nitrophenols. The obtained limits of detection and quantification under optimized conditions were 0.01-0.02 and 0.04-0.05 µg/dm3, respectively. The relative standard deviations (n = 5) were less than 3.8% (at 10 µg/dm3). Moreover, the calculated enrichment factors were above 200. In addition, the relative recoveries for a spiked river water sample were satisfactory.

Design and optimization of a cost-effective paper-based voltammetric sensor for the determination of trinitrotoluene (TNT) utilizing cysteamine-linked Fe3O4 @Au nanocomposite.

This paper presents the development and optimization of a cost-effective paper electrochemical sensor for the detection of TNT using Fe3O4-Au core-shell nanoparticles modified with cysteamine (Fe3O4@Au/CA). The sensor was constructed by modifying a graphite paste with the aforementioned nanoparticles, which facilitated the formation of a Meisenheimer complex between cysteamine and TNT as an electron donor and an electron acceptor, respectively. The central composite design was employed to optimize four key parameters pH, modifier percentage, contact time, and buffer type to enhance the performance of the sensor. The detection limit was found to be 0.5 nM of TNT, while the linear range of the electrode response spanned from 0.002 µM to 10 µM. The simplicity and low cost of the sensor make it highly attractive for practical applications, particularly in scenarios where rapid and on-site TNT detection is required.

A zirconium metal-organic framework functionalized with a S/N containing carboxylic acid (MOF-808(Zr)-Tz) as an efficient sorbent for the ultrafast and selective dispersive solid phase micro extraction of chromium, silver, and rhodium in water samples.

Metal-organic frameworks (MOFs) are good adsorbents for targeted chemicals with their adjustable properties. Herein, we prepared a zirconium based MOF (MOF-808(Zr)) and functionalized it employing 2-mercapto-4-methyl-5-thiazolacetic acid (MOF-808(Zr)-Tz). The prepared MOFs were characterized by XRD, FTIR, SEM-EDX, TGA, N2 sorption, zeta potential measurements, and elemental analysis. The surface area of MOF-808(Zr)-Tz was 1348 m2/g. Dispersive solid-phase micro-extraction (D-SPµE) method based on MOF-808(Zr)-Tz was firstly developed and applied to the extraction of chromium, silver, and rhodium in waters. The determination of the analytes was done by FAAS. The optimal pH and eluent for analytes were 7.0 and 3 mL of 2 mol L-1 HCl, respectively. The contact times were 1 min for adsorption and 3 min for elution. The LOD and PFs of the D-SPµE for analytes were 2.3 µg L-1 and 13.3 for chromium, 2.1 µg L-1 and 13.3 for silver, and 3.1 µg L-1 and 13.3 rhodium, respectively. The D-SPµE method was verified with analyses of NW-TMDA-54.6 Lake water and SPS-WW1 Batch 114 Wastewater and with spiked dam water, river water, well water, sea water, and wastewater. The recoveries of the analytes changed from 89 to 108 %. The results indicated that the method is selective, simple, effective, and rapid for extracting chromium(III), silver(I) and rhodium(III) in waters.

Recent developments of (bio)-sensors for detection of main microbiological and non-biological pollutants in plastic bottled water samples: A critical review.

The importance of water in all biological processes is undeniable. Ensuring access to clean and safe drinking water is crucial for maintaining sustainable water resources. To elaborate, the consumption of water of inadequate quality can have a repercussion on human health. Furthermore, according to the instability of tap water quality, the consumption rate of bottled water is increasing every day at the global level. Although most people believe bottled water is safe, it can also be contaminated by microbiological or chemical pollution, which can increase the risk of disease. Over the last decades, several conventional analytical tools applied to analyze the contamination of bottled water. On the other hand, some limitations restrict their application in this field. Therefore, biosensors, as emerging analytical method, attract tremendous attention for detection both microbial and chemical contamination of bottled water. Biosensors enjoy several facilities including selectivity, affordability, and sensitivity. In this review, the developed biosensors for analyzing contamination of bottled water were highlighted, as along with working strategies, pros and cons of studies. Challenges and prospects were also examined.

Analytical methods for determining environmental contaminants of concern in water and wastewater.

Control and prevention of environmental pollution have emerged as paramount global concerns. Anthropogenic activities, such as industrial discharges, agricultural runoff, and improper waste disposal, introduce a wide range of contaminants into various ecosystems. These pollutants encompass organic and inorganic compounds, particulates, microorganisms, and disinfection by-products, posing severe threats to human health, ecosystems, and the environment. Effective monitoring methods are indispensable for assessing environmental quality, identifying pollution sources, and implementing remedial measures. This paper suggests that the development and utilization of highly advanced analytical tools are both essential for the analysis of contaminants in water samples, presenting a foundational hypothesis for the review. This paper comprehensively reviews the development and utilization of highly advanced analytical tools which is mandatory for the analysis of contaminants in water samples. Depending on the specific pollutants being studied, the choice of analytical methods widely varies. It also reveals insights into the diverse applications and effectiveness of these methods in assessing water quality and contaminant levels. By emphasizing the critical role of the reviewed monitoring methods, this review seeks to deepen the understanding of pollution challenges and inspire innovative monitoring solutions that contribute to a cleaner and more sustainable global environment.•Urgent global concerns: control and prevention of pollution from diverse sources.•Varied contaminants, diverse methods: comprehensive review of analytical tools.•Inspiring a sustainable future: innovative monitoring for a cleaner environment.

Adsorption enrichment integrated with paper-based devices for detection of trace levels of hexavalent chromium in water samples.

In the present study, a sensitive microfluidic paper-based analytical device (µ-PADs) integrated with adsorption enrichment procedure was developed to analyze Cr(VI) in water samples. The affecting factors, including pH and amounts of reagents were optimized. The limit of detection of 0.0015 mg L-1 and linear range of 0.005-2 mg L-1 were achieved with good intra- and inter-day precision of 5.1 and 7.6% RSD, respectively. The results obtained by the proposed method were validated by inductively coupled plasma-optical emission spectrometry (ICP-OES). The recoveries of the present method and ICP-OES were ranged from 96.3 to 109.0‬% and 106.0 to 109.7%, respectively. The two sets of (µ-PADs and ICP-OES) results were in a good agreement as paired t-test indicated no significant differences. The proposed method could be utilized for analyzing trace levels of Cr(VI) in water samples in the absence of conventional analytical instruments.

PathoSense: a rapid electroanalytical device platform for screening Salmonella in water samples.

Salmonella contamination is a major global health challenge, causing significant foodborne illness. However, current detection methods face limitations in sensitivity and time, which mostly rely on the culture-based detection techniques. Hence, there is an immediate and critical need to enhance early detection, reduce the incidence and impact of Salmonella contamination resulting in outbreaks. In this work, we demonstrate a portable non-faradaic, electrochemical sensing platform capable of detecting Salmonella in potable water with an assay turnaround time of ~ 9 min. We evaluated the effectiveness of this sensing platform by studying two sensor configurations: one utilizing pure gold (Au) and the other incorporating a semiconductor namely a zinc oxide thin film coated on the surface of the gold (Au/ZnO). The inclusion of zinc oxide was intended to enhance the sensing capabilities of the system. Through comprehensive experimentation and analysis, the LoD (limit of detection) values for the Au sensor and Au/ZnO sensor were 0.9 and 0.6 CFU/mL, respectively. In addition to sensitivity, we examined the sensing platform's precision and reproducibility. Both the Au sensor and Au/ZnO sensor exhibited remarkable consistency, with inter-study percentage coefficient of variation (%CV) and intra-study %CV consistently below 10%. The proposed sensing platform exhibits high sensitivity in detecting low concentrations of Salmonella in potable water. Its successful development demonstrates its potential as a rapid and on-site detection tool, offering portability and ease of use. This research opens new avenues for electrochemical-based sensors in food safety and public health, mitigating Salmonella outbreaks and improving water quality monitoring.

Non-target screening in water analysis: recent trends of data evaluation, quality assurance, and their future perspectives.

This trend article provides an overview of recent advancements in Non-Target Screening (NTS) for water quality assessment, focusing on new methods in data evaluation, qualification, quantification, and quality assurance (QA/QC). It highlights the evolution in NTS data processing, where open-source platforms address challenges in result comparability and data complexity. Advanced chemometrics and machine learning (ML) are pivotal for trend identification and correlation analysis, with a growing emphasis on automated workflows and robust classification models. The article also discusses the rigorous QA/QC measures essential in NTS, such as internal standards, batch effect monitoring, and matrix effect assessment. It examines the progress in quantitative NTS (qNTS), noting advancements in ionization efficiency-based quantification and predictive modeling despite challenges in sample variability and analytical standards. Selected studies illustrate NTS's role in water analysis, combining high-resolution mass spectrometry with chromatographic techniques for enhanced chemical exposure assessment. The article addresses chemical identification and prioritization challenges, highlighting the integration of database searches and computational tools for efficiency. Finally, the article outlines the future research needs in NTS, including establishing comprehensive guidelines, improving QA/QC measures, and reporting results. It underscores the potential to integrate multivariate chemometrics, AI/ML tools, and multi-way methods into NTS workflows and combine various data sources to understand ecosystem health and protection comprehensively.

Determination of Eugenol Residues in Fish Tissue, Transport, and Temporary Water of Aquatic Product by Gas Chromatography-Tandem Mass Spectrometry with Application of the Electrospun Nanofibrous Membrane.

Using gas chromatography-tandem mass spectrometry and electrospun nanofibrous membrane, we developed and validated a simple, rapid, and sensitive methodology for quantifying eugenol residues in fish tissue and water samples. Fish tissue extract and water samples (315 samples) collected from three southeastern China provinces (Shanghai, Zhejiang, and Fujian), originating from eight provinces of Zhejiang, Jiangsu, Shandong, Guangdong, Fujian, Anhui, Shanghai, and Jiangxi, from April 2021 to April 2023 were filtered with an electrospun nanofiber membrane, extracted with trichloromethane/n-hexane, and directly concentrated to dry after simple purification. An internal standard of p-terphenyl in n-hexane and 5-µL injection volumes of the solutions was used to analyze eugenol via internal calibration with a minimum concentration of 0.5 µg/L in water samples and 0.1 µg/kg in aquatic product samples. The highest amount of eugenol was detected in Fujian province, possibly due to the higher temperature during transportation, while the lowest amount was found in Shanghai, which mainly uses temporary fish-culture devices. This is a fast, inexpensive, and effective method for testing large quantities of fish water and meat samples.

Complete holography-based system for the identification of microparticles in water samples.

Here, we present a comprehensive holography-based system designed for detecting microparticles through microscopic holographic projections of water samples. This system is designed for researchers who may be unfamiliar with holographic technology but are engaged in microparticle research, particularly in the field of water analysis. Additionally, our innovative system can be deployed for environmental monitoring as a component of an autonomous sailboat robot. Our system's primary application is for large-scale classification of diverse microplastics that are prevalent in water bodies worldwide. This paper provides a step-by-step guide for constructing our system and outlines its entire processing pipeline, including hologram acquisition for image reconstruction.

Development of a column switching for direct online enrichment and separation of polar and nonpolar analytes from aqueous matrices.

Trace substances in surface waters may threaten health and pose a risk for the aquatic environment. Moreover, separation and detection by instrumental analysis is challenging due to the low concentration and the wide range of polarities. Separation of polar and nonpolar analytes can be achieved by using stationary phases with different selectivity. Lower limits of detection of trace substances can be obtained by offline enrichment on solid phase materials. However, these practices require substantial effort and are time consuming and costly. Therefore, in this study, a column switching was developed to enrich and separate both polar and nonpolar analytes by an on-column large volume injection of aqueous samples. The column switching can significantly reduce the effort and time for analyzing trace substances without compromising on separation and detection. A reversed phase (RP) column is used to trap the nonpolar analytes. The polar analytes are enriched on a porous graphitized carbon column (PGC) coupled serially behind the RP column. A novel valve switching system is implemented to enable elution of the nonpolar analytes from the RP column and, subsequently, elution of polar analytes from the PGC column and separation on a hydrophilic interaction liquid chromatography (HILIC) column. To enable separation of polar analytes dissolved in an aqueous matrix by HILIC, the water plug that is flushed from the PGC column is diluted by dosing organic solvent directly upstream of the HILIC column. The developed method was tested by applying target analysis and non-target screening, highlighting the advantage to effectively separate and detect both polar and nonpolar compounds in a single chromatographic run. In the target analysis, the analytes, with a logD at pH 3 ranging from -2.8 to + 4.5, could be enriched and separated. Besides the 965 features in the RP phase, 572 features from real wastewater were observed in the HILIC phase which would otherwise elute in the void time in conventional one-dimensional RP methods.

Synthesis and characterization of pH-responsive deep eutectic solvent followed by HPLC for trace determination of bisphenol A in water samples.

A microextraction based on pH-responsive deep eutectic solvent combined with high-performance liquid chromatography was developed for the separation, preconcentration, and determination of bisphenol A in water samples. Five deep eutectic solvents were prepared using thymol (hydrogen bond acceptor) and 6-, 8-, 9-, 10-, and 12-carbon carboxylic acids (hydrogen bond donor), and were used as extraction solvent. Herein, by alkalinizing the environment, phase transition takes place, and by adding acid, phase separation and extraction of analytes occur simultaneously. Some important parameters on the extraction such as deep eutectic solvent type, molar ratio of deep eutectic solvent components, deep eutectic solvent volume, potassium hydroxide concentration, hydrochloric acid volume, extraction time, and salt addition were optimized. Under the optimum conditions, intra- and interday precisions of the method based on seven replicate measurements of 10 µg L-1 of bisphenol A in water samples were 2.2% and 4.3%, respectively. The analytical performance of the method showed linearity over the concentration of 0.05-50 µg L-1 with the detection limit of 0.02 µg L-1 . The accuracy of the method was confirmed by spiking different concentrations of bisphenol A in real water samples and obtaining relative recoveries in the range of 92.5%-105.2%.