Synergistic Toughening of Epoxy Composite with Cellulose Nanofiber and Continuous Pineapple Leaf Fiber as Sustainable Reinforcements.

In this work, the effect of cellulose nanofiber (CNF) on the mechanical properties of long pineapple leaf fiber (PALF)-reinforced epoxy composites was investigated. The content of PALF was fixed at 20 wt.% and the CNF content was varied at 1, 3, and 5 wt.% of the epoxy matrix. The composites were prepared by hand lay-up method. Comparison was conducted between CNF-, PALF- and CNF-PALF-reinforced composites. It was found that the introduction of these small amounts of CNF into epoxy resin caused very small effects on flexural modulus and strength of neat epoxy. However, impact strength of epoxy with 1 wt.% CNF increased to about 115% that of neat epoxy, and, as the content of CNF increased to 3 and 5 wt.%, the impact strength decreased to that of neat epoxy. Observation of the fractured surface under electron microscope revealed the change in failure mechanism from a smooth surface to a much rougher surface. For epoxy containing 20 wt.% PALF, both flexural modulus and strength increased significantly to about 300% and 240% that of neat epoxy. The composite impact strength increased to about 700% that of the neat epoxy. For hybrid systems containing both CNF and PALF, there were few changes observed in both flexural modulus and strength compared to the PALF epoxy system. However, much improvement in impact strength was obtained. By using epoxy containing 1 wt.% CNF as the matrix, the impact strength increased to about 220% that of 20 wt.% PALF epoxy or 1520% that of neat epoxy. It thus could be deduced that the spectacular improvement in impact strength was due to the synergistic effect of CNF and PALF. The failure mechanism leading to the improvement in impact strength will be discussed.

Epoxy-Modified Bismaleimide Structural Adhesive Film Toughened Synergistically with PEK-C and Core-Shell Polymers for Bonding CFRP.

Bismaleimide (BMI) resin-based structural adhesives have excellent heat resistance, with important applications demonstrated in the bonding of high-temperature BMI composites. In this paper, we report an epoxy-modified BMI structural adhesive with excellent properties for bonding BMI-based CFRP. We prepared the BMI adhesive using epoxy-modified BMI as the matrix and PEK-C and core-shell polymers as synergistic tougheners. We found that the epoxy resins improve the process and bonding properties of BMI resin but slightly reduce thermal stability. PEK-C and core-shell polymers synergistically improve the toughness and bonding performances of the modified BMI adhesive system and allow the maintenance of heat resistance. The optimized BMI adhesive exhibits excellent heat resistance, with a high glass transition temperature of 208.6 °C and a high thermal degradation temperature of 425.4 °C. Most importantly, the optimized BMI adhesive exhibits satisfactory intrinsic bonding and thermal stability. It has a high shear strength of 32.0 MPa at room temperature and up to 17.9 MPa at 200 °C. The BMI adhesive-bonded composite joint has a high shear strength of 38.6 and 17.3 MPa at room temperature and 200 °C, respectively, indicating effective bonding and excellent heat resistance.

Synergistic Delamination Toughening of Glass Fiber-Aluminum Laminates by Surface Treatment and Graphene Oxide Interleaf.

The synergistic effects of surface treatment and interleaf on the interlaminar mechanical properties of glass fiber-aluminum laminates were studied. Aluminum sheets were treated with alkaline etching. Meanwhile, a graphene oxide (GO) interleaf was introduced between the aluminum sheet and the glass fiber-reinforced epoxy composite. Double cantilever beam and end-notched flexure tests were employed to evaluate the interlaminar fracture toughness of the glass fiber-aluminum laminates. The obtained results show that the toughening efficiency of the interleaf is dependent on the aluminum surface characteristics as well as the GO loading. Further comparison reveals that the highest mode-I and mode-II fracture toughnesses are obtained in the specimens with alkali etching treatment and addition of GO interleaf with 0.5 wt% of GO loading, which are 510% and 381% higher in comparison to the plain specimen. Fracture surfaces were observed to further uncover the reinforcement mechanisms.

Integrated Ternary Bioinspired Nanocomposites via Synergistic Toughening of Reduced Graphene Oxide and Double-Walled Carbon Nanotubes.

With its synergistic toughening effect and hierarchical micro/nanoscale structure, natural nacre sets a "gold standard" for nacre-inspired materials with integrated high strength and toughness. We demonstrated strong and tough ternary bioinspired nanocomposites through synergistic toughening of reduced graphene oxide and double-walled carbon nanotube (DWNT) and covalent bonding. The tensile strength and toughness of this kind of ternary bioinspired nanocomposites reaches 374.1 ± 22.8 MPa and 9.2 ± 0.8 MJ/m(3), which is 2.6 and 3.3 times that of pure reduced graphene oxide film, respectively. Furthermore, this ternary bioinspired nanocomposite has a high conductivity of 394.0 ± 6.8 S/cm and also shows excellent fatigue-resistant properties, which may enable this material to be used in aerospace, flexible energy devices, and artificial muscle. The synergistic building blocks with covalent bonding for constructing ternary bioinspired nanocomposites can serve as the basis of a strategy for the construction of integrated, high-performance, reduced graphene oxide (rGO)-based nanocomposites in the future.

Synergistic toughening of graphene oxide-molybdenum disulfide-thermoplastic polyurethane ternary artificial nacre.

Inspired by the ternary structure of natural nacre, robust ternary artificial nacre is constructed through synergistic toughening of graphene oxide (GO) and molybdenum disulfide (MoS2) nanosheets via a vacuum-assisted filtration self-assembly process. The synergistic toughening effect from high mechanical properties of GO and lubrication of MoS2 nanosheets is successfully demonstrated. Meanwhile, the artificial nacre shows high electrical conductivity. This approach for constructing robust artificial nacre by synergistic effect from GO and MoS2 provides a creative opportunity for designing and fabricating integrated artificial nacre in the near future, and this kind of ternary artificial nacre has great potential applications in aerospace, flexible supercapacitor electrodes, artificial muscle, and tissue engineering.