RESUMO
Polybromodiphenyl ethers (PBDEs), the widely used flame retardants, are common contaminants in surface soils at e-waste recycling sites. The association of PBDEs with soil colloids has been observed, indicating the potential risk to groundwater due to colloid-facilitated transport. However, the extent to which soil colloids may enhance the spreading of PBDEs in groundwater is largely unknown. Herein, we report the co-transport of decabromodiphenyl ester (BDE-209) and soil colloids in saturated porous media. The colloids released from a soil sample collected at an e-waste recycling site in Tianjin, China, contain high concentration of PBDEs, with BDE-209 being the most abundant conger (320 ± 30 mg/kg). The colloids exhibit relatively high mobility in saturated sand columns, under conditions commonly observed in groundwater environments. Notably, under all the tested conditions (i.e., varying flow velocity, pH, ionic species and ionic strength), the mass of eluted BDE-209 correlates linearly with that of eluted soil colloids, even though the mobility of the colloids varies markedly depending on the specific hydrodynamic and solution chemistry conditions involved. Additionally, the mass of BDE-209 retained in the columns also correlates strongly with the mass of retained colloids. Apparently, the PBDEs remain bound to soil colloids during transport in porous media. Findings in this study indicate that soil colloids may significantly promote the transport of PBDEs in groundwater by serving as an effective carrier. This might be the reason why the highly insoluble and adsorptive PBDEs are found in groundwater at some PBDE-contaminated sites.
Assuntos
Coloides , Retardadores de Chama , Água Subterrânea , Éteres Difenil Halogenados , Poluentes do Solo , Solo , Poluentes Químicos da Água , Éteres Difenil Halogenados/análise , Coloides/química , Água Subterrânea/química , Poluentes do Solo/análise , Poluentes do Solo/química , Solo/química , Poluentes Químicos da Água/análise , China , Retardadores de Chama/análise , Monitoramento Ambiental , Modelos QuímicosRESUMO
Food waste is a serious worldwide issue that has an impact on the environment, society, and economy. This comprehensive review provides a detailed description of methods and approaches for reducing food waste, emphasizing the necessity of comprehensive strategies to tackle its intricate relationship with environmental sustainability, social equity, and economic prosperity. By scrutinizing the extent and impact of food waste, from initial production stages to final disposal, this comprehensive review underlines the urgent need for integrated solutions that include technological advancements, behavioral interventions, regulatory frameworks, and collaborative endeavors. Environmental assessments highlight the significant contribution of food waste to greenhouse gas emissions, land degradation, water scarcity, and energy inefficiency, thereby emphasizing the importance of curtailing its environmental impact. Concurrently, the social and economic consequences of food waste, such as food insecurity, economic losses, and disparities in food access, underscore the imperative for coordinated action across multiple sectors. Food waste can also be effectively reduced by various innovative approaches, such as technological waste reduction solutions, supply chain optimization strategies, consumer behavior-focused initiatives, and waste recovery and recycling techniques. Furthermore, in order to foster an environment that encourages the reduction of food waste and facilitates the transition to a circular economy, legislative changes and regulatory actions are essential. By embracing these multifaceted strategies and approaches, stakeholders can unite to confront the global food waste crisis, thereby fostering resilience, sustainability, and social equity within our food systems.
Assuntos
Reciclagem , Gerenciamento de Resíduos , Reciclagem/métodos , Gerenciamento de Resíduos/métodos , Abastecimento de Alimentos , Alimentos , Perda e Desperdício de AlimentosRESUMO
The increasing global demand for cement significantly impacts greenhouse gas emissions and resource consumption, necessitating sustainable alternatives. This study investigates fresh geopolymer (GP) pastes incorporating 20 wt.% of five industrial wastes-suction dust, red mud from alumina production, electro-filter dust, and extraction sludges from food supplement production and from partially stabilized industrial waste-as potential replacements for traditional cement. Consistent synthesis methods are used to prepare the geopolymers, which are characterized for their physicochemical, mechanical, and biological properties. Ionic conductivity and pH measurements together with integrity tests, thermogravimetry analysis (TGA), and leaching analysis are used to confirm the stability of the synthesized geopolymers. Fourier-transform Infrared (FT-IR) spectroscopy is used to follow geopolymerization occurrences. Results for ionic conductivity, pH, and integrity revealed that the synthesized GPs were macroscopically stable. TGA revealed that the main mass losses were ascribable to water dehydration and to water entrapped in the geopolymer networks. Only the GP filled with the powder of the red mud coming from alumina production experienced a mass loss of 23% due to a partial waste degradation. FT-IR showed a red shift in the main Si-O-(Si or Al) absorption band, indicating successful geopolymer network formations. Additionally, most of the GPs filled with the wastes exhibited higher compressive strength (37.8-58.5 MPa) compared to the control (22 MPa). Only the GP filled with the partially stabilized industrial waste had a lower mechanical strength as its structure was highly porous because of gas formation during geopolymerization reactions. Despite the high compressive strength (58.5 MPa) of the GP filled with suction dust waste, the concentration of Sb leached was 25 ppm, which limits its use. Eventually, all samples also demonstrated effective antimicrobial activity against Escherichia coli and Staphylococcus aureus due to the alkaline environment and the presence of metal cations able to react with the bacterial membranes. The findings revealed the possibility of recycling these wastes within several application fields.
RESUMO
Anaerobic digestion (AD) has the potential to catalyse the shift from a linear to a circular economy. However, effective treatment and management of both solid (DSF) and liquid (DLF) digestate fraction treatment and management require adopting sustainable technologies to recover valuable by-products like energy, biofuels, biochar, and nutrients. This study reviews state-of-the-art advanced technologies for DSF and DLF treatment and valorisation, using life cycle assessment (LCA) and techno-economic analysis (TEA) in integrated digestate management (IDM). Key findings highlight these technologies' potential in mitigating environmental impacts from digestate management, but there's a need to improve process efficiency, especially at larger scales. Future research should prioritize cost-effective and eco-friendly IDM technologies. This review emphasizes how LCA and TEA can guide decision-making and promote sustainable agricultural practices. Ultimately, sustainable IDM technologies can boost resource recovery and advance circular economy principles, enhancing the environmental and economic sustainability of AD processes.
Assuntos
Agricultura , Agricultura/métodos , Agricultura/economia , Anaerobiose , Biocombustíveis/economia , Eliminação de Resíduos/métodos , Eliminação de Resíduos/economiaRESUMO
Carbon dioxide (CO2) capture has been identified as a potential technology for reducing the anthropic emissions of greenhouse gases, particularly in post-combustion processes. The development of adsorbents for carbon capture and storage is expanding at a rapid rate. This article presents a novel sustainable synthesis method for the production of chitosan/activated carbon CO2 adsorbents. Chitosan is a biopolymer that is naturally abundant and contains amino groups (-NH2), which are required for the selective adsorption of CO2. Spent coffee grounds have been considered as a potential feedstock for the synthesis of activated coffee grounds through carbonization and chemical activation. The chitosan/activated coffee ground composite microspheres were created using the emulsion cross-linking method with epichlorohydrin. The effects of the amount of chitosan (15, 20, and 25 g), activated coffee ground (10, 20, 30, and 40%w/w), and epichlorohydrin (2, 3, 4, 5, 6, 7 and 8 g) were examined. The CO2 capture potential of the composite beads is superior to that of the neat biopolymer beads. The CO2 adsorbed of synthesized materials at a standard temperature and pressure is improved by increasing the quantity of activated coffee ground and epichlorohydrin. These findings suggest that the novel composite bead has the potential to be applied in CO2 separation applications.
Assuntos
Dióxido de Carbono , Carvão Vegetal , Quitosana , Café , Epicloroidrina , Epicloroidrina/química , Dióxido de Carbono/química , Quitosana/química , Café/química , Adsorção , Carvão Vegetal/química , Microesferas , Reagentes de Ligações Cruzadas/químicaRESUMO
Economic and environmental considerations have elucidated research interests on the best approach to managing electronic waste (e-waste), which has increasing social, environmental, and economic impacts. Proper e-waste managementis essential for resource recovery, environmental sustainability, and public health protection, and effective management of e-waste necessitates analytical techniques to assess and characterize their elemental composition. Despite expansive literature published on the topic of e-waste, there is scarce coverage of the various analytical techniques employed to characterize the inorganic contents of e-waste. This review discusses the various e-waste characterization techniques used in studies published between 2013 and 2023. Specifically, this review covers the analytical approaches employed to characterize the inorganic content of e-waste, the electronic devices or their components analyzed, the elements identified, the sample preparation methods adopted, and the merits and demerits of the analytical procedures. This review highlights the disparate approaches to e-waste characterization and the need for reliable and repeatable e-waste analysis and sample preparation methods.
Assuntos
Resíduo Eletrônico , Reciclagem , Gerenciamento de Resíduos , Resíduo Eletrônico/análise , Reciclagem/métodos , Gerenciamento de Resíduos/métodosRESUMO
Plastic waste management has received significant attention in recent decades due to the urgent global environmental crisis caused by plastic pollution. The versatile and durable nature of plastic has led to its widespread usage across various sectors. However, its nonbiodegradable nature contributes to unsustainable production practices, leading to extensive landfill usage and posing threats to marine ecosystems and the food chain. To address these environmental concerns, numerous challenges have been recently addressed through investigating alternative approaches for disposing of plastic waste, with the construction sector emerging as a promising option. Incorporating plastic waste materials into concrete not only offers economic benefits but also provides a valid alternative to conventional disposal methods. This paper presents the results of different experimental studies, some of them available in the literature and others new, discussing the feasibility of integrating plastic waste into concrete and its impact on mechanical properties. The influence of different sizes, natures, treatments, and percentages of plastic waste in the concrete mixtures is dealt with in order to provide further data for helping to understand the nonunivocal results in the literature, under the conviction that only further observations can help to understand the mechanics of concrete with plastic aggregates. The experimental investigation highlighted that one parameter that is better than others and can be considered to compare different experimental investigations is the variation in weight (due to the effective volume of plastics in the mix), determining a sort of increasing of porosity that degrades the mechanical characteristics. However, this seems inconsistent in some cases. Therefore, the need for further research is highlighted to refine production methods and optimize mix designs.
RESUMO
In order to understand the organophosphate flame retardants (OPFRs) pollution and evaluate the inhalation exposure risk in formal e-waste recycling facilities, the air concentrations, particle size distribution and gas-particle partitioning of OPFRs in four typical workshops were investigated. The total Σ15OPFR concentrations inside workshops were in the range of 64.7-682 ng/m3, with 5.80-23.4 ng/m3 in gas phase and 58.8-658 ng/m3 in particle phase. Triphenyl phosphate (TPHP) and tris(2-chloroisopropyl) phosphate (TCIPP) were main analogs, both of which contributed to 49.0-85.7% of total OPFRs. In the waste printed circuit boards thermal treatment workshop, the OPFRs concentration was the highest, and particle-bound OPFRs mainly distributed in 0.7-1.1 µm particles. The proportions of TPHP in different size particles increased as the decrease of particle size, while TCIPP presented an opposite trend. The gas-particle partitioning of OPFR analogs was dominated by absorption process, and did not reach equilibrium state due to continuous emission of OPFRs from the recycling activities. The deposition fluxes of OPFRs in respiratory tract were 65.7-639 ng/h, and the estimated daily intake doses of OPFRs were 8.52-76.9 ng/(kg·day) in four workshops. Inhalation exposure was an important exposure pathway for e-waste recycling workers, and deposition fluxes of size-segregated OPFRs were mainly in head airways region.
Assuntos
Resíduo Eletrônico , Retardadores de Chama , Organofosfatos , Tamanho da Partícula , Reciclagem , Retardadores de Chama/análise , China , Organofosfatos/análise , Humanos , Exposição Ocupacional/análise , Exposição por Inalação/estatística & dados numéricos , Poluentes Atmosféricos/análise , Monitoramento Ambiental/métodos , Poluentes Ocupacionais do Ar/análiseRESUMO
The aim of the present study, an attempt to shed light on the use of industrial-based wastes as alkali-activated binder (AAB) material is mainly. The present novel research work, the characterization of waste ferrochrome slag (FCS) and the performance of alkali-activated mortar consisting of fly ash (FA) were investigated. The characterization of used materials were carried out using advanced microstructural analysis techniques (XRF, XRD and SEM). A total of thirty two mortars are prepared using FCS (90-60%) and FA (10-40%) with 5 M, 10 M sodium hydroxide (NaOH), Na2SiO3/NaOH (SS/SH = 1 and 2) solution. All specimens were cured in an oven at 70 °C and 100 °C for 24 h. After oven curing, the geopolymer mortars were kept in the laboratory for 28 days and thermal and mechanical tests were applied to them. The A5 mixture (SS/SH = 1 with 10%FA, 90%FCS and 5 M NaOH) was found to be optimum in terms of thermal insulation properties, making it suitable for use in sustainable construction in terms of low energy cost through exterior insulation. The C8 mixture (SS/SH = 1 with 40%FA, 60% FCS and 10 M NaOH) was found to be optimum in terms of strength and durability, making it suitable for use in sustainable construction. As a result, in this study, an optimum mixture of waste FCS and FA was obtained and geopolymer building materials that provide thermal insulation and structural performance and are resistant to external influences were produced.
RESUMO
This review addresses the critical issue of a rapidly increasing worldwide waste stream and the need for sustainable management. The paper proposes an integrated transformation toward a next-generation methanization process, which leads not only to treating waste but also to converting it into higher value compounds and greener energy. Although the current and commonly used anaerobic digestion process is useful for biogas production, it presents limitations of resource exploitation and some negative environmental impacts. Focusing on the acidogenic stage in waste stream processing, the paper discusses the recent strategies to enhance the recovery of volatile fatty acids (VFAs). These acids serve as precursors for synthesizing a variety of biochemicals and biofuels, offering higher value products than solely energy recovery and soil fertilizers. Additionally, the importance of recycling the fermentation residues back into the biorefinery process is highlighted. This recycling not only generates additional VFAs but also contributes to generating clean energy, thereby enhancing the overall sustainability and efficiency of the waste management system. Moreover, the review discusses the necessity to integrate life cycle assessment (LCA) and techno-economic analysis (TEA) to evaluate the environmental impacts, sustainability, and processing costs of the proposed biorefinery.
Assuntos
Biocombustíveis , Ácidos Graxos Voláteis , Ácidos Graxos Voláteis/metabolismo , Metano/metabolismo , Anaerobiose , Fermentação , Gerenciamento de Resíduos/métodos , ReciclagemRESUMO
This study explores the adhesive properties of copolymers comprising glycidyl methacrylate (GMA) and 3-(trimethoxysilyl)propyl methacrylate (MPTMS), focusing on their suitability for adhesive applications. Peel resistance measurements revealed a substantial impact of the GMA/MPTMS ratio on adhesion capabilities, identifying an optimal ratio of 30/70 for copolymerization with tert-butyl acrylate (tBA) to improve foaming performance. tBA, a foaming monomer activated by a photoacid generator and heat, enhances the copolymerized adhesive's adhesion strength and foamability for postuse delamination. Chemical structure analysis through Nuclear magnetic resonance (NMR) and Fourier-transform infrared spectroscopy (FTIR) confirmed successful polymerization, while rheological properties indicated decreased complex viscosity and adhesive strength with an increasing tBA content. The deprotection of the t-butyl group facilitated foam formation, supported by morphology analysis. These findings provide insights into foamable adhesive development with potential applications in delamination processes and implications for further exploration in polymer adhesion.
RESUMO
Integrated circuits (ICs) and central processing units (CPUs), essential components of electrical and electronic equipment (EEE), are complex composite materials rich in recyclable high-value strategic and critical metals, with many in concentrations higher than in their natural ores. With gold the most valuable metal present, increase in demand for gold for EEE and its limited availability have led to a steep rise in the market price of gold, making gold recycling a high priority to meet demand. To overcome the limitations associated with conventional technologies for recycling e-waste, the use of greener technologies (ionic liquids (ILs) as leaching agents), offers greater potential for the recovery of gold from e-waste components. While previous studies have demonstrated the efficiency and feasibility of using ILs for gold recovery, these works predominantly concentrate on the extraction stage and often utilise simulated solutions, lacking the implementation of a complete process validated with real samples to effectively assess its overall effectiveness. In this work, a simulated Model Test System was used to determine the optimal leaching and extraction conditions before application to real samples. With copper being the most abundant metal in the e-waste fractions, to access the gold necessitated a two-stage pre-treatment (nitric acid leaching followed by aqua regia leaching) to ensure complete removal of copper and deliver a gold-enriched leach liquor. Gold extraction from the leach liquor was achieved by liquid-liquid extraction using Cyphos 101 (0.1 M in toluene with an O:A = 1:1, 20 °C, 150 rpm, and 15 min) and as a second process by sorption extraction with loaded resins (Amberlite XAD-7 with 300 mg of Cyphos 101/g of resins at 20 °C, 150 rpm and 3 h). In both processes, complete stripping and desorption of gold was achieved (0.5 M thiourea in 0.5 M HCl) and gold recovered, as nanoparticles of purity ≥95%, via a reduction step using a sodium borohydride solution (0.1 M NaBH4 in 0.1 M NaOH). These two hydrometallurgical processes developed can achieve overall efficiencies of ≥95% for gold recovery from real e-waste components, permit the reuse of the IL and resins up to five consecutive times, and offer a promising approach for recovery from any e-waste stream rich in gold.
Assuntos
Ouro , Líquidos Iônicos , Reciclagem , Líquidos Iônicos/química , Ouro/química , Reciclagem/métodos , Resíduo EletrônicoRESUMO
By 2050, the world's population is predicted to reach over 9 billion, which requires 70% increased production in agriculture and food industries to meet demand. This presents a significant challenge for the agri-food sector in all aspects. Agro-industrial wastes are rich in bioactive substances and other medicinal properties. They can be used as a different source for manufacturing products like biogas, biofuels, mushrooms, and tempeh, the primary ingredients in various studies and businesses. Increased importance is placed on resource recovery, recycling, and reusing (RRR) any waste using advanced technology like IoT and artificial intelligence. AI algorithms offer alternate, creative methods for managing agro-industrial waste management (AIWM). There are contradictions and a need to understand how AI technologies work regarding their application to AIWM. This research studies the application of AI-based technology for the various areas of AIWM. The current work aims to discover AI-based models for forecasting the generation and recycling of AIWM waste. Research shows that agro-industrial waste generation has increased worldwide. Infrastructure needs to be upgraded and improved by adapting AI technology to maintain a balance between socioeconomic structures. The study focused on AI's social and economic impacts and the benefits, challenges, and future work in AIWM. The present research will increase recycling and reproduction with a balance of cost, efficiency, and human resources consumption in agro-industrial waste management.
Assuntos
Agricultura , Inteligência Artificial , Resíduos Industriais , Gerenciamento de Resíduos , Gerenciamento de Resíduos/métodos , Agricultura/métodos , ReciclagemRESUMO
Sustainable anode materials, including natural silica and biomass-derived carbon materials, are gaining increasing attention in emerging energy storage applications. In this research, we highlighted a silica/carbon (SiO2/C) derived from Streblus asper leaf wastes using a simple method. Dried Streblus asper leaves, which have plenty of biomass in Thailand, have a unique leaf texture due to their high SiO2 content. We can convert these worthless leaves into SiO2/C nanocomposites in one step, producing eco-materials with distinctive microstructures that influence electrochemical energy storage performance. Through nanostructured design, SiO2/C is thoroughly covered by a well-connected framework of conductive hybrid polymers based on the sodium alginate-polypyrrole (SA-PPy) network, exhibiting impressive morphology and performance. In addition, an excellent electrically conductive SA-PPy network binds to the SiO2/C particle surface through crosslinker bonding, creating a flexible porous space that effectively facilitates the SiO2 large volume expansion. At a current density of 0.3 C, this synthesized SA-PPy@Nano-SiO2/C anode provides a high specific capacity of 756 mAh g-1 over 350 cycles, accounting for 99.7% of the theoretical specific capacity. At the high current of 1 C (758 mA g-1), a superior sustained cycle life of over 500 cycles was evidenced, with over 93% capacity retention. The research also highlighted the potential for this approach to be scaled up for commercial production, which could have a significant impact on the sustainability of the lithium-ion battery industry. Overall, the development of green nanocomposites along with polymers having a distinctive structure is an exciting area of research that has the potential to address some of the key challenges associated with lithium-ion batteries, such as capacity degradation and safety concerns, while also promoting sustainability and reducing environmental impact.
RESUMO
Printed circuit boards (PCBs) make up a substantial amount of electronic waste (e-waste) generated annually. Waste PCBs contain high quantities of copper and gold in comparison to natural ores. As such, "urban mining" of waste PCBs to recover these metals is of commercial interest. In this work, we used life cycle assessment to compare the environmental impact of four copper and gold recovery processes. We evaluated pyrometallurgy, chemical leaching, and bioleaching, as well as a hybrid leaching process that uses bioleaching to recover copper and chemical leaching to recover gold. Furthermore, we considered differences in environmental impact based on differences in electricity sources. If electricity comes from fossil fuels, the pyrometallurgical process results in the lowest environmental impact in all impact categories studied. If electricity comes from carbon-free sources, the pyrometallurgical process results in the lowest environmental impact in all categories studied except global warming, where the hybrid leaching process results in the lowest impact. In all cases, metal recovery from waste PCBs leads to lower environmental impact than primary metal production. Our goal is to guide e-waste recyclers towards more environmentally sustainable metal recovery processes and to provide knowledge gaps in the field to guide future research.
RESUMO
This study addresses the challenge of incomplete separation of mechanically recovered residual films and impurities in cotton fields, examining their impact on resource utilization and environmental pollution. It introduces an innovative screening method that combines pneumatic force and mechanical vibration for processing crushed film residue mixtures. A double-action screening device integrating pneumatic force and a key-type vibrating screen was developed. The working characteristics of this device were analyzed to explore the dynamic characteristics and kinematic laws of the materials using theoretical analysis methods. This led to the revelation of the screening laws of residual films and impurities. Screening tests were conducted using the Central Composite Design method, considering factors such as fan outlet, fan speed, vibration frequency of the screen, and feeding amount, with the impurity-rate-in-film (Q) and film-content-in-impurity (W) as evaluation indexes. The significant influence of each factor on the indexes was determined, regression models between the test factors and indexes were established, and the effect laws of key parameters and their significant interaction terms on the indexes were interpreted. The optimal combination of working parameters for the screening device was identified through multivariable optimization methods. Validation tests under this optimal parameters combination showed that the impurity-rate-in-film was 3.08% and the film-content-in-impurity was 1.94%, with average errors between the test values and the predicted values of 3.36% and 5.98%, respectively, demonstrating the effectiveness of the proposed method. This research provides a novel method and technical reference for achieving effective separation of residual film and impurities, thereby enhancing resource utilization.
Assuntos
Gossypium , Fibra de Algodão/análise , Poluição Ambiental/prevenção & controleRESUMO
The imminent generation of significant amounts of Li ion battery waste is of concern due to potential detrimental environmental impacts. However, this also poses an opportunity to recycle valuable battery materials for later use. One underexplored area is using commonly employed cathode materials such as nickel, manganese cobalt (NMC) oxide as an electrocatalyst for water splitting reactions. In this work we explore the possibility of using NMC materials of different metallic ratios (NMC 622 and 811) as oxygen evolution and hydrogen evolution catalysts under alkaline conditions. We show that both materials are excellent oxygen evolution reaction (OER) electrocatalysts but perform poorly for the hydrogen evolution reaction. NMC 622 demonstrates the better OER activity with an overpotential of only 280â mV to pass 100â mA cm-2 and a low tafel slope of 42â mV dec-1. The material can also pass high current densities of 150â mA cm-2 for 24â h while also being tolerant to extensive potential cycling indicating suitability for direct integration with renewable energy inputs. This work demonstrates that NMC cathode materials if recovered from Li ion batteries are suitable OER electrocatalysts.
RESUMO
BACKGROUND: The effects of prenatal element exposure on mothers and fetuses have generated concern. Profiles of trace and toxic elements in biological material are urgently desired, especially for women who reside near e-waste recycling facilities. The aim of this study was to investigate elements concentrations in placenta, cord blood, and maternal blood of women and to evaluate the influencing factors. METHODS: A group of 48 women from an e-waste recycling site and a group of 31 women from a non-e-waste recycling site were recruited. Basic characteristics were collected by questionnaire and the concentrations of 17 elements in placenta, cord blood, and maternal blood samples were analyzed by inductively coupled plasma mass spectrometry (ICP-MS). Finally, the generalized linear model regression analysis (GLM) was used to test the association between element concentrations and possible factors. RESULTS: Compared to the control group, the exposed group had significantly elevated cadmium (Cd), zinc (Zn), nickel (Ni), and antimony (Sb) in placenta, and higher lead (Pb) in maternal blood and cord blood (P<0.05). Sb concentration in maternal blood was significantly lower than in the control group (P<0.05). GLM analysis showed that element concentrations were mainly associated with maternal age [chromium (Cr), iron (Fe), selenium (Se), cobalt (Co), mercury (Hg) in placenta, copper (Cu) in maternal blood], education (Se, Sb in placenta), family income (Cu in maternal blood and Ni in placenta), passive smoking [Cu and Zn in placenta, Pb in maternal blood], and e-waste contact history (Hg in cord blood, Cu, Zn, and Cd in maternal blood). CONCLUSIONS: Women in the e-waste recycling area had higher toxic element levels in the placenta and blood samples. More preventive measures were needed to reduce the risk of element exposure for mothers and fetuses in these areas.
Assuntos
Resíduo Eletrônico , Sangue Fetal , Placenta , Humanos , Feminino , Sangue Fetal/química , Sangue Fetal/metabolismo , Gravidez , Adulto , Placenta/metabolismo , Placenta/química , Reciclagem , Oligoelementos/sangue , Adulto JovemRESUMO
Disposable bamboo chopsticks (DBCs) are difficult to recycle, which inevitably cause secondary pollution. Based on energy and environmental issues, we propose a facile strategy to fabricate floatable photocatalyst (fPC) coated onto DBCs, which can be flexibly used in water purification. The photocatalyst of titania and titanium carbide on bamboo (TiO2/TiC@b) was successfully constructed from TiC-Ti powders and DBCs using a coating technique followed heat treatment in carbon powder, and the fPC exhibited excellent photocatalytic activity under visible light irradation. The analysis results indicate that rutile TiO2 forms on TiC during heat treatment, achieving a low-density material with an average value of approximately 0.5233 g/cm3. The coatings of TiO2/TiC on the bamboo are firm and uniform, with a particle size of about 20-50 nm. XPS results show that a large amount of oxygen vacancies is generated, due to the reaction atmosphere of more carbon and less oxygen, further favoring to narrowing the band gap of TiO2. Furthermore, TiO2 formed on residual TiC would induce the formation of a heterojunction, which effectively inhibits the photogenerated electron-hole recombination via the charge transfer effect. Notably, the degradation of dye Rhodamine B (Rh.B) is 62.4% within 3 h, while a previous adsorption of 36.0% for 1 h. The excellent photocatalytic performance of TiO2/TiC@b can be attributed to the enhanced reaction at the water/air interface due to the reduced light loss in water, improved visible-light response, increased accessible area and charge transfer effect. Our findings show that the proposed strategy achieves a simple, low-cost, and mass-producible method to fabricate fPC onto the used DBCs, which is expected to applied in multiple fields, especially in waste recycling and water treatment.
RESUMO
Electronic waste recycling companies have proliferated in many countries due to valuable materials present in end-of-life electronic and electrical equipment. This article examined the business characteristics and management performance of Electronic Products Recycling Association (EPRA), a Canadian nationwide electronic product stewardship organization. The organization's annual performance reports, from 2012 to 2020, for nine Canadian provinces in which it currently operates were aggregated and analyzed. Temporal analysis using regression and Mann-Kendall tests were employed, and five characteristics of EPRA's business were analyzed, including e-waste products collected, number of drop-off locations, efforts to build public awareness, operating expenses, and growth of e-waste stewardship. Results show a decline in the amount of e-waste collected across the provinces, except in New Brunswick, which started its program in 2017. The Mann-Kendall test revealed declining temporal trends in most provinces. Although the collection/drop off sites and stewardship organizations increased astronomically over the study period in Canada, the amounts of e-waste collected decreased. We found that public awareness generally did not increase the amount of e-waste collected, and these campaigns only appeared to be effective in jurisdictions with good accessibility of e-waste recycling. Processing cost accounted for the majority of the e-waste management budget in Canada, and different factors affected the financial success of the stewards differently.