Static Loading of Different Intraradicular Preparation Depths of Trinia Endocrowns in Maxillary Canines.

AIM: The aim of this study is to compare the fracture resistance of canine teeth restored using TRINIA Endocrowns with three different types of preparations (2, 3, and 4 intracanal preparations). MATERIALS AND METHODS: Thirty maxillary-extracted canines were collected. All teeth were fixed in orthodontic acrylic resin and decapitated at the level of the proximal cemento-enamel junction (CEJ). After being endodontically treated, specimens were distributed equally between 3 groups (n = 10) with different preparation depths (GT: 2 mm Intraradicular Preparation, GH: 3 mm Intraradicular Preparation, GF: 4 mm Intraradicular Preparation). Thirty TRINIA endocrowns were dry milled. After surface treatment, all endocrowns were bonded to their corresponding roots using Permaflo a dual-cure resin cement. Each specimen was then fixed in the lower part of a universal testing machine with a load cell of 5 KN, at an angle of 45 degrees to the tooth long-axis at 0.5 mm/min crosshead speed. Failure loads were recorded in Newton's. Data were recorded, organized, and statistically investigated. RESULTS: Shapiro-Wilk tests revealed that the data were not normally distributed. Descriptive statistics revealed a high mean fracture resistance of GH (647 N), then GT (475.6 N), and finally GF (353.9 N). The Kruskal-Wallis test revealed a significant difference that existed between the groups being studied (p = 0.036). CONCLUSION: TRINIA endocrowns with intracanal preparations of 2 and 3 mm provide more promising fracture resistance than those with intracanal preparations of 4 mm as a way of treating of root-canal-treated maxillary canines. TRINIA endocrowns (2 and 3 mm intracanal preparations) are as promising as fiber posts and all ceramic crowns in terms of fracture resistance. TRINIA endocrowns with 2 mm intracanal preparations are mostly reparable after failure, but those of 3 and 4 mm are mostly irreparable after failure. CLINICAL SIGNIFICANCE: Modifying endocrowns to have intraradicular projections, simulating Nayyar core, may improve the success and longevity of endocrowns in anterior teeth. How to cite this article: Alahmad AM, Alenezi AY, Rayyan M, et al. Static Loading of Different Intraradicular Preparation Depths of Trinia Endocrowns in Maxillary Canines. J Contemp Dent Pract 2024;25(6):575-580.

Comparative Evaluation of Fracture Resistance in Different Post and Core Systems with Varying Ferrule Locations: An In Vitro Study.

AIM: Endodontically treated teeth often require 360° ferrule to retain post and core restoration. The literature support on scientific evidence of partial ferrule is limited, hence this study was conducted to evaluate the fracture resistance of two post and core systems, i.e., Edelweiss and glass fiber post and core system with varying ferrule locations. MATERIALS AND METHODS: About 54 extracted mandibular 1st premolars were divided into Edelweiss post and core (Group A) and glass fiber post and core (Group B). They were further subdivided into 3 groups each (Partial functional, partial non-functional, and circumferential). A standardized endodontic procedure was carried out on all the specimens. For group A, an Edelweiss drill of 1.4 mm was used to prepare the post space. Canals were then etched, a bonding agent was applied and posts were luted with paracore resin. For group B, post space was prepared with a straight fissure bur, followed by the same procedure as that of group A. Core build-up was done with composite resin. Cast crowns were fabricated and cemented with GIC. Fracture resistance was evaluated with UTM with a compressive load capacity of 1000 N until fracture occurred. RESULTS: The results of this study stated that in the Edelweiss group partial functional ferrule showed higher fracture resistance and in the glass fiber group circumferential ferrule showed higher fracture resistance. The study also showed that MOF is favorable in all the groups. CONCLUSION: The type of ferrule was one of the factors that affected the fracture resistance of Edelweiss and Glass fiber post and core group of specimens. The study also concluded that there was a predominant favorable mode of fracture across all groups, in all different ferrule locations. CLINICAL SIGNIFICANCE: This study opens multiple avenues and methods in tooth restoration and shows that even a partial functional ferrule is sufficient for restoration, provided the right system is used. How to cite this article: Jadhav PD, Shetty R, Mehta D, et al. Comparative Evaluation of Fracture Resistance in Different Post and Core Systems with Varying Ferrule Locations: An In Vitro Study. J Contemp Dent Pract 2024;25(5):480-485.

Comparison of Compressive Strength Between Traditional and Novel Open-Faced Stainless Steel Crowns Filled With Different Restorative Materials.

Purpose: To compare the compressive strength of traditional open-faced stainless-steel crown (OFSSC) to novel Preformed OFSSC (POFSSC) filled with different restorative materials. Methods: Seventy-five uniform 3D-printed models were divided into five groups (n=15): Group one (G1) traditional OFSSC; Group two (G2) POFSSC with restorative composite; Group three (G3) POFSSC with bulk-fill composite; Group four (G4) POFSSC with flowable resin restorative; and Group 5 (G5) POFSSC with resin-reinforced glass-ionomer. Samples were subjected to 1,000 cycles of thermocycling, at five degrees to 55 degrees Celsius, followed by a tactile exam. Instron was used for compressive strength test, with the maximum force at fracture initiation recorded in Newtons (N). Failure of the facial-surface was categorized as <50% facial-surface chipped, ≥50% to <100% facial-surface chipped, or the entire facial-surface came-off. One-way analysis of variance and the Kruskal-Wallis test was used (P<0.05). Results: All samples were intact during the tactile exam following thermocycling. The compressive strengths are ranked as: G2???784.66±86.29 N; G3???730.46±159.52 N; G4???726.33±150.47 N; G1???650.59±116.05 N; G5???556.60±137.65 N. The compressive strength of G2 was significantly higher than G1 (P=0.007). G5 showed significantly lower compressive strength than G2 (P=0.0), G3 (P=0.001), and G4 (P=0.001). The entire facial-surface cameoff as follows: G2???6.67%; G4???13.33%; G5???26.67%; G3???53.33%; G1???66.67%. Conclusion: Compressive strength of G2 was significantly higher than control; and G2 had the lowest percentage of the entire facial-surface coming-off.

An in vitro evaluation of tensile strength of molar endocrown milled from various computer aided design and manufacturing materials.

New computer-aided design and computer-aided manufacturing (CAD-CAM) materials have been reported to have suitable mechanical and physical properties for endocrown restorations. However, there is a lack of literature on evaluating the retention of endocrown using these materials. This in vitro study aimed to compare the retention of endocrowns fabricated from 3 different CAD-CAM materials. Sixty human mandibular third molars were divided into 3 groups (n = 20) according to the material used: (e.max CAD, Ivoclar AG, Schaan, Liechtenstein), (HC, Shofu, Koyoto, Japan), and (Brilliant Crios, Coltene, Altstätten, Switzerland) (n = 20). Specimens were stored in distilled water at 37 °C for 1 week and subjected to 5000 thermal cycles. A universal testing machine (5500R/1123, Instron, Norwood, USA) was used to measure the tensile force. All results were statistically analyzed using one-way ANOVA (α = 0.05), and different failure modes were demonstrated. The results revealed that e. max CAD showed the highest mean tensile force value (402.35 ± 15.812) N, and the lowest mean tensile force value was for Brilliant Coris (118.90 ± 12.430) N (P < .001). It is concluded that e.max CAD endocrowns showed the highest tensile force values after thermocycling in comparison to other materials with a significant difference, which may have a promising impact on the survival of endocrown restorations.

Of the article: evaluation of the masticatory efficiency of children with stainless steel crowns: a pilot cross-sectional split-mouth study.

BACKGROUND: Stainless steel crowns (SSCs) are commonly employed to restore the posterior teeth of children and over the years, they are available with improved anatomical shapes. This study was conducted to evaluate and assess the effect of the placement of SSCs on the masticatory efficiency of children. METHODS: This pilot cross-sectional split-mouth study assessed masticatory efficiency in children aged 6-11 years. Fifteen participants, each with stainless-steel crowns placed unilaterally at least one month prior, were included. This study utilized two flavours of trident chewing gum (red and green) to measure masticatory efficiency. The child was asked to chew half a strip of red and green chewing gum placed one on top of the other using either the noncrown or crown side 15 times. Another set of chewing gum was given to the child to chew 20 times on the same side. The chewing exercise was repeated using teeth on the other side. Chewed gum samples were collected, photographed, and analysed via ImageJ software to determine the red and green areas. Masticatory efficiency was subsequently calculated with the help of a formula in which the red areas and green areas were calculated via ImageJ software. The data were analysed with paired t tests via SPSS (version 20.0). RESULTS: When the mean values of the crown side were compared with those of the noncrown side following 15 chewing cycles, the chewing efficiency on the noncrown side was greater, with a difference of 0.303, whereas the chewing efficiency following 20 chewing cycles was greater on the crown side, with a difference of 0.814. However, both differences were statistically nonsignificant, with t values of -0.07 and 0.26, respectively, and p values of 0.94 and 0.8, respectively. CONCLUSION: The presence of SSCs on the molars of children did not affect masticatory efficiency.

In-vitro comparison of fracture resistance of CAD/CAM porcelain restorations for endodontically treated molars.

BACKGROUND: This study evaluates the fracture strength and patterns of feldspathic porcelain restorations made using CAD/CAM technology for lower first molars with extensive crown destruction. The restorations include post-core and full-contour crown, composite resin core and full-contour crown, and endocrown. This research provides insights into effective restorative options to address tooth fracture risk, supporting minimally invasive procedures and CAD/CAM integration in dental practices. METHODS: This study utilized 80 permanent mandibular first molars, which were divided into four groups: Group I (Post-Core-Full-contour crown), Group II (Core- Full-contour crown), Group III (Endocrown), and Group IV (Control). Root canal treatment was performed on all samples except for the control group. Following access cavity preparation, restorations for each tooth were fabricated using the CAD/CAM system and cemented with resin cement. The specimens were embedded in acrylic blocks. After undergoing thermomechanical aging, the samples were subjected to fracture resistance testing using a universal testing machine, which applied force until fracture occurred. The fracture patterns were subsequently analyzed, and the data were statistically evaluated using the Kruskal-Wallis and Chi-Square tests (p < 0.05). RESULTS: A significant difference in fracture values under axial forces was observed (p < 0.05). The control group had the highest fracture strength (1830 ± 277 N), while the Core- full-contour crown group showed the lowest (1532 ± 371 N). Failure types varied significantly among the groups (χ2 = 26.886, df = 9, p = 0.001). The most common failure type was Type-2 (33.75%), characterized by restorable fractures, while Type-3 fractures, unrestorable, were the least common (12.5%). CONCLUSIONS: The findings underscore the significance of technological advancements in CAD/CAM for effectively restoring endodontically treated teeth with extensive crown damage. This study contributes valuable insights, emphasizing the clinical relevance of selecting appropriate restorative options to mitigate the risk of tooth fracture associated with coronal restoration failures.

Removable partial dentures: Part 2.

The provision of removable partial dentures (RPDs) is an important skill for practitioners. It can often be challenging to make a successful prosthesis which the patient finds satisfactory. This three-part series has been designed to provide an overview of the clinical management of patients requiring RPDs. This second part discusses three clinical scenarios that may be commonly faced in general dental practice: the use of immediate dentures for patients requiring extractions; the management of patients with lone-standing teeth using windowed dentures; and the incorporation of surveyed crowns into cobalt chromium RPDs. For each clinical technique, the advantages, disadvantages and indications are summarised.

Minimizing excess cement around implant restorations: an in vitro study of cementation techniques.

Excess cement around cement-retained implant crowns is associated with a higher incidence of peri-implantitis, but there are limited data to indicate which cement application technique minimizes excess cement. The purpose of this in vitro study was to evaluate the amount of excess cement that resulted from different cement application techniques. Fifty identical titanium custom abutments and monolithic zirconia crowns were digitally designed and milled in the shape of a maxillary first molar. Ten crowns were cemented by applying temporary cement only to the intaglio coronal surface of the crown; these specimens were used as a control group to determine the amount of cement to be used in all other groups. Four different cement application methods were evaluated (n = 10): wall layer technique, in which cement was brushed on the intaglio axial walls of the crown; precementation technique, in which cement was applied to the intaglio coronal aspect of the crown, and the crown was precemented on an abutment replica, quickly removed, and then repositioned on the milled abutment; rim application, in which cement was applied to the cervical marginal rim of the crown; and increased cement space, in which the cement space was increased to 60 µm (compared with 40 µm in other groups) and cement was brushed on the intaglio coronal surface. Digital photographs of the cemented crowns were taken, and image editing software was used to measure the displacement of excess cement, that is, the distance that it traveled below the finish line on the mesial, distal, buccal, and lingual surfaces. Excess cement was then removed from each specimen and weighed. An analysis of variance test was used to evaluate the difference among groups, and each pair of groups was compared with the t test. Compared with all of the other experimental groups, specimens cemented with the wall layer technique showed a significantly smaller amount of cement excess in terms of both the distance traveled and weight (P < 0.05). Based on the findings, the wall layer cementation technique, in which cement is brushed on the intaglio walls of the crown, is recommended to reduce excess cement around implant crowns.

Comparison of flexural strength, marginal gap, and internal fit of milled and 3D-printed crown materials.

The purpose of this study was to compare the flexural strength, Weibull modulus (reliability), marginal gap, and internal fit (internal gap) of 4 materials for milling or 3-dimensional (3D) printing of definitive and provisional crowns: IPS e.max CAD (IEC), Paradigm MZ100 Block (PMB), Permanent Crown Resin (PCR), and Temporary CB Resin (TCR). Flexural strength was tested by subjecting sectioned milling blocks (IEC and PMB) or 3D-printed bars (PCR and TCR) to a 3-point bending test in a universal testing machine (n = 15 per material). Crowns were milled or 3D printed, and the marginal gap and internal fit were measured using microcomputed tomography (n = 5 per material). The data were analyzed with a t test and compared using analysis of variance (ANOVA) with Tukey post hoc comparisons (α = 0.05). The groups demonstrated the following mean (SD) flexural strength values: IEC, 335.50 (28.97) MPa; PMB, 154.34 (21.03) MPa; PCR, 128.09 (7.30) MPa; and TCR, 126.29 (9.23) MPa. A 1-way ANOVA revealed significant differences in the flexural strengths of sectioned and 3D-printed bars (P < 0.001). The PMB group showed the lowest Weibull modulus (8.77), indicating its poor reliability. The IEC group showed the smallest marginal gap, 53.42 (31.99) µm; this value was significantly smaller than the gap in the TCR group (P < 0.001) but not the PCR or PMB group. The PMB group had the smallest internal fit discrepancy (87.44 [37.60] µm) but was not significantly different from PCR, while TCR had a significantly greater internal fit discrepancy (130.61 [65.16] µm) than IEC, PMB, and PCR (P < 0.001). The occlusal internal fit discrepancies of 3D-printed crowns were significantly greater than those of milled crowns (P < 0.001). There was no statistically significant difference in flexural strength between the 3D-printed definitive (PCR) and provisional (TCR) materials. When the data were combined according to manufacturing method, the marginal gap and internal fit of crowns fabricated with 3D printing were comparable to those of milled crowns, and all mean marginal gaps were within a clinically acceptable limit of less than 120 µm.

Evaluation of Wear on Primary Tooth Enamel and Fracture Resistance of Esthetic Pediatric Crowns Manufactured from Different Materials.

Background and Objectives: Advances in dental materials and CAD-CAM technology have expanded crown options in primary teeth due to their improved appearance and mechanical properties. Thus, this study aimed to assess the enamel wear and fracture resistance of prefabricated, milled, and 3D-printed esthetic pediatric crowns. Materials and Methods: The study involved 60 extracted maxillary second primary molars and 60 3D-printed resin dies, divided into six groups based on different crown materials (n = 10): prefabricated zirconia, prefabricated composite, milled composite, milled resin matrix ceramic, milled PEEK, and 3D-printed resin. Prefabricated crowns were selected after the preparation of the typodont mandibular second primary molar tooth, while milled and 3D-printed crowns were custom produced. The specimens underwent mechanical loading of 50 N at 1.6 Hz for 250,000 cycles with simultaneous thermal cycling. The 3D and 2D wear amounts were evaluated by scanning the specimens before and after aging. Then, the fracture resistance and failure types of the restorations were recorded. Results: The results showed that the milled PEEK group had superior fracture resistance compared to the other groups, while prefabricated zirconia crown group had the lowest value. Milled resin matrix ceramic crown group displayed the lowest 3D wear volume, while 3D-printed crown group showed the highest 2D wear. Conclusions: The restorative material type did not have a significant effect on the wear of primary tooth enamel. The fracture resistance of the tested materials differed according to the material type. Although the milled PEEK group showed the highest fracture resistance, all tested materials can withstand chewing forces in children.

Conservative management of malpositioned maxillary anterior implant. Technique description and case report.

This case report presents the conservative management of a malposed implant in the maxillary anterior region caused by craniofacial bone remodeling. The patient expressed dissatisfaction with the position and shade of an implant that was placed almost three decades previously. After evaluating different treatment options, the patient opted to replace the implant prosthesis. The selected treatment consisted of a zirconia crown layered with feldspathic porcelain (including pink porcelain) cemented onto a screw-retained customized zirconia abutment with an angled screw channel for the single-unit permanent fixed implant prosthesis. The report highlights the importance of informed decision making and patient preferences in treatment option selection. It emphasizes the conservative approach of replacing a malposed implant prosthesis with pink porcelain to address the patient's esthetic concerns. Dental photographs and shade-matching protocols were crucial in achieving satisfactory esthetic outcomes. The report also underscores the potential for infraocclusion as well as proclination caused by craniofacial growth in implant therapy, and emphasizes the significance of patient education regarding long-term considerations.

[Analysis of polyetheretherketone framework on the stress distribution of implant-supported fixed maxillary prosthesis: 3-D finite element analysis].

PURPOSE: To analyze the stress distribution of polyetheretherketone framework of implant-supported fixed maxillary prosthesis by three-dimensional finite element method. METHODS: Three dimensional finite element model of implant-supported fixed maxillary prosthesis was established. Polyetheretherketone as framework material, resin, zirconia, PEEK, baked plastic and lithium silicate were used to make crown prosthesis as experimental group, pure titanium and monolithic zirconia prosthesis model was used as control group. The feasibility of PEEK framework was analyzed by loading 150N axially and obliquely on the first molar, and the maximum compressive stress, minimum tensile stress and von Mises principal stress of the framework, crown, screw, implant, cortical and cancellous bone were measured and compared. RESULTS: Under axially loading, the von Mises stress in the monolithic zirconia and lithium silicate crowns were 361 MPa and 295 MPa, while the stress in resin and PEEK crowns were 35 MPa and 37 MPa, respectively. The screw von Mises stress of the experimental group was 694-724 MPa, which was much higher than 61 MPa of the control group.The maximum and minimum stresses of the screw appeared in the resin crown and PEEK crown group. Under oblique loading,von Mises stress of the framework in the experimental group was lower than that in the control group, but the maximum stress appeared in the resin crown and PEEK crown. von Mises stresses of monolic zirconia and lithium disilicate crowns in the experimental group were higher than that of resin and PEEK crowns. von Mises stress of the implant in the experimental group was twice that of the control group. von Mises stress in screw of the experimental group was much higher than that of the control group, and the maximum stress was 22 times that of the control group. The stresses of cancellous bone and cortical bone in the experimental group were twice that of the control group, and the differences were larger than that under vertical loading. CONCLUSIONS: In order to reduce the stress of crowns,resin or PEEK materials are preferred to be used as the crown prosthesis when PEEK was framework of implant-supported fixed maxillary prosthesis. Reducing the cantilever and lateral force may avoid excessive stress in screw.

Dental Biofilm Accumulation and Gingival Health of Teeth with Fixed Single Prosthesis Fabricated by Various Prosthetic Materials.

Background Periodontal health plays an important role in maintaining the health of natural teeth as well as in the success of all dental procedures. Fixed single prosthesis (dental crown) can be fabricated with different types of prosthetic restorative materials like Metal, Ceramic, Ceramic fused to metal. These different materials have different affinity for plaque accumulation leading to the development of gingival inflammation and periodontal disease. Objective To determine the amount of Plaque accumulation and gingival health of teeth with a fixed single prosthesis fabricated by various Prosthetic materials. Method This quantitative cross-sectional study was carried out from July 2021 to March 2022. The patients who visited the hospital after six months of use of the prosthesis enrolled and were categorized into three groups according to the material used for the prosthesis metal, ceramic, and metal-ceramic. The periodontal condition was assessed using the plaque index and gingival index. Result A total of 136 patients (78 female and 58 male) were enrolled in the study, with a mean age of 39.44 ± 16.23 years (Range 19 - 70 years). There were 47 patients with ceramic crowns, 39 patients with metallic, and 50 patients with metal ceramic crowns. The mean plaque index of metal, ceramic, and metal-ceramic crowns was found 1.15 ± 0.546, 0.86 ± 0.479, and 0.93 ± 0.498 respectively. Similarly, the mean gingival index of metal, ceramic, and metal-ceramic crown were 1.22 ± 0.56, 0.91 ± 0.48, and 1.09 ± 0.55 respectively. Conclusion The dental biofilm (plaque) accumulation and hence gingival inflammation is less in ceramic crowns than in metal and metal-ceramic crowns.

Effect of cementation protocols on the fracture load of bilayer ceramic crowns manufactured by the Rapid Layer Technology.

To evaluate the fracture load of bilayer ceramic crowns manufactured by Rapid Layer Technology (RLT) after different cementation protocols of the veneering ceramic to the zirconia infrastructures. Sixty epoxy resin preparations simulating a molar tooth were obtained and 60 zirconia infrastructures and feldspathic crowns were manufactured by RLT and divided into 6 groups according to the cementation protocol at the interface to veneering ceramic (n=10): Ctr- control: conventional resin cement; Al- Al2O3 sandblasting 50µm + conventional resin cement; Al/MDP- Al2O3 sandblasting (50µm) + resin cement with MDP; Sil- silicatization 30µm + conventional resin cement; Gl/HF- glaze + hydrofluoridric acid (5%,60s) + silane + conventional resin cement; Gl- glazing as bonding agent. The feldspathic ceramic internal surface was etched with fluoridric acid (5%) + silane followed by cementation according to respective protocols. All samples were mechanically cycled (200N and 4.5x105 Pa, 37°C, 2x106 cycles, 3.4Hz) and submitted to axial compressing fracture load test (10kN, 0.5mm/min). The results(N) were submitted to descriptive and analytical statistical analysis with 1-way ANOVA, Weibull, and the Tukey test (α=0.05). ANOVA revealed that there was a significant difference among the tested groups (p<0.0001). The group Al/MDP presented the higher resistance to fracture (1972.46A N), followed by the Ctr group (1584.41B N). The characteristic strength(σ0) was significantly different (p=0.000). The crack and chipping were the predominant failures. The air-abrasion at the external surface of zirconia with Al2O3 followed by cementation with MDP resin cement, should be selected to Rapid Layer Technique when felspathic ceramic is used as veneer ceramic.

Exploring fiberglass post numbers for enhanced fatigue resistance in molars without coronary remnants.

This study aimed to assess the fatigue resistance of molars lacking a coronary remnant, using zero, one, two, or three fiberglass posts. Forty caries/crack-free human molars with coronal portions removed at the pulp chamber floor were randomly allocated into four groups (n=10). Following endodontic treatment, posts (Whitepost DC/DC.E 0.5, 1.0, FGM) were silanized (silane agent, Angelus) and cemented with a resin cement (RelyX U200, 3M ESPE). Resin composite cores (Z350, 3M ESPE) were built, and metal crowns were fabricated and cemented using the same luting system. Samples underwent cyclic fatigue testing at 45°, applying load in the occlusal surface at 10 Hz and 100 N initial load for 10,000 cycles, with 50 N increments every 10,000 cycles until failure. Fatigue failure load and cycles for failure data were recorded and subjected to survival analysis through Kaplan-Meier and Mantel-Cox post hoc tests, and Weibull analysis. Fractography patterns of failed crowns were qualitatively analyzed. The group without posts exhibited the lowest fatigue performance (p < 0.05) for both fatigue failure load and cycles to failure. Superior fatigue performance was observed in the three-post group, followed by groups with one or two posts, corroborated by the Weibull characteristic strength parameter. Weibull moduli were similar among conditions. All specimens exhibited failure involving detachment of the restorative set (posts/core/crown) with a portion of the dental remnant, without tooth fracture. Thus, when restoring mandibular molars without crown remnants, the use of fiberglass posts promotes greater fatigue resistance to oblique loads.

Knowledge, Awareness, and Use of Stainless-Steel Crowns Among Dental Professionals in Sana'a City, Yemen.

BACKGROUND Stainless-steel crowns (SSCs) have been the most effective and efficient methods of tooth restoration in pediatric dentistry, and they have shown consistently high success rates. This study aimed to evaluate the knowledge, awareness, and practice of SSCs among dental professionals in Sana'a City, Yemen. MATERIAL AND METHODS A modified questionnaire was prepared from previous similar studies and distributed to 700 participants. It consisted of 3 parts: the first was related to participant characteristics; the second consisted of questions related to knowledge and awareness of SSCs such as indications, advantages, challenges, and parent's rejection to SSCs; and the third part was correlated to questions related to the use and practice of SSCs, number of children treated, and SSCs cemented per week. Statistical significance was determined using a chi-square test, and the P value was set at <0.05 for statistical significance. RESULTS A total of 604 dental professionals answered the questionnaire, 159 (26.3%) had used SSC restoration, and 12 (80.0%) of them had a degree in pediatric dentistry, with significant differences among participants (P<0.000). Respondents with higher academic qualifications recorded higher percentages in using SSCs during their clinics, with significant differences (P<0.005). A significant difference was detected between general practitioners and pedodontists in practice questions (P=0.000). Most of the respondents (78.8%) indicated a desire for more practice and hands-on training in use of SSCs. CONCLUSIONS General dentists in Sana'a City, Yemen, do not frequently use SSCs. Most of the respondents stated that they lacked practical training and expressed a need for further knowledge and continuing education.

Surface topography changes and wear resistance of different non-metallic telescopic crown attachment materials in implant retained overdenture (prospective comparative in vitro study).

BACKGROUND: The purpose of this study was to evaluate the effect of using different types of metallic and non-metallic telescopic crown attachment materials on wear resistance and surface tomography changes in implant-retained mandibular overdentures. MATERIALS AND METHODS: Completely edentulous mandibular epoxy models were fabricated, in which two implants were placed in the canine region and retained to the implants with three different material combinations used for the construction of telescopic attachments. Thirty-three identical mandibular overdentures were fabricated using the conventional standardized technique. The study groups were divided into three categories according to the material used for the construction of the secondary copings. The primary copings in all the study groups were constructed of PEEK, while the secondary coping in group I was PEEK, group II was ZrO2 and CoCr for group III. Primary copings were cemented on a ready-made abutment. Secondary copings were placed over the primary copings in the desired path of insertion, then picked up into the intaglio surface of the overdentures. A cyclic loading machine was used to apply repeated insertion-removal cycles simulating nearly 10 years of clinical use. Stereomicroscope with a built-in camera was used to monitor the reduction in width of the primary copings to evaluate the wear resistance of each material combination. RESULTS: There was highly statistically significant difference between the study groups after the application of 1.000, 5.000 and 10.000 cycles. The highest level of wear resistance was recorded for the PEEK/PEEK combination, whereas PEEK/ZrO2 and PEEK/CoCr showed no significant differences. CONCLUSIONS: Implant retained overdenture with PEEK-PEEK telescopic crown attachment is associated with the highest wear resistance among all the study groups. PEEK-PEEK combination may be the treatment of choice for fabrication of telescopic attachment in implant retained overdenture as it provides better resistance to wear. It offers the advantages for geriatric patients as it decreases the possibility for repeated repair and replacement of attachment, increase long-term patient satisfaction and shelf life of prosthesis.

Clinical outcomes and supragingival microbiota analysis around dental implants and teeth in patients with a history of periodontitis: a preliminary study of 6 months follow-up.

OBJECTIVES: To investigate the supragingival microbiome surrounding dental implants and neighbouring tooth in periodontitis history and periodontally healthy patients. METHODS: Subjects with a history of periodontitis (test) and periodontally healthy subjects (control) received one of two types of dental implants with different surface characteristics: sandblasted acid-etched (SLA) or precision dimension laser-treated (PDL). Periodontal clinical measurements were collected at baseline (V1), 3 months after implant placement (V4), at zirconia crown placement (V6) and 3 months after zirconia crown placement (V8). Supragingival bacterial microbiota was studied using Illumina MiSeq sequencing. RESULTS: Supragingival microbial community on SLA implants in test group significantly differed to control group at V8 (p < 0.05). A longitudinal shift displaying microbial dysbiosis occurred on SLA implants (p < 0.05) and adjacent teeth (p < 0.05) among test patients from V6 to V8. On PDL implants and the adjacent tooth, no significant difference between test and control groups from V6 to V8 (p > 0.05). Co-occurrence network in test group of SLA implants and the adjacent tooth at V8 showed increased disease-associated bacteria and reduced health-associated bacteria. Health-associated bacteria were dominant in control group of SLA implants at V8. CONCLUSION: The surface characteristics and prosthetic components of dental implants may be important risk factors in patients with a history of periodontitis. CLINICAL RELEVANCE: Dysbiosis of supragingival microbiome may predispose dental implants to peri-implant diseases. Thus, a strict supportive periodontal care plan is imperative to prevent early onset of biological complications.

[New intraoral digital impression with pneumatic gingival retraction used in the restoration of crown for posterior teeth: a case report].

In fixed prosthodontics, clear exposure of the preparation margin is the prerequisite for obtaining accurate digital impressions and improving the marginal fit of restorations. To resolve the issues associated with the cord retraction technique, such as pain, acute injury, and prolonged procedural time, this study proposes a new technology for intraoral digital impression taking with pneumatic gingival retraction. The new scanning head blows a high-speed airflow that instantaneously separates the free gingiva, locally exposing the subgingival preparation margin. Combined with the farthest point preservation stitching algorithm based on the distance from the normal vector and high-speed laser scanning photography, it achieves global preparation edge data and gingival reconstruction, realizing painless, non-invasive, and efficient precise acquisition of the preparation margin. Using this new technique, a patient with a full porcelain crown restoration on a posterior tooth was treated. The digital impression revealed a clear margin of the preparation, and the crown made from this data has a good marginal fit.

Efficacy evaluation of zirconia crown on primary molars with caries defects.

OBJECTIVES: This study aimed to estimate the therapeutic effects of preformed metal crown (PMC) and prefabricated zirconia crowns (ZC) on decayed primary morals in children, as well as to analyze the possible influencing factors. METHODS: A retrospective cohort study was performed on the data of 192 patients (aged 3 to 8) in the Stomatological Department of Shenzhen Children's Hospital from October 2021 to December 2021. The decayed mandibular first molars were selected and restored by vital-pulp therapy followed by PMC and ZC, including 96 cases (96 caries) in the PMC group and 96 cases (96 caries) in the ZC group. Oral clinical examination was performed at 3 months, 1 year, and 2 years after treatment, overwiewing the clinical therapeutic effects and periodontal status of PMC and ZC groups, as well as recording the crown integrity, gingival index (GI), probing bleeding index (BI), plaque index (PLI) and various prosthetic indices. RESULTS: No significance differences existed in the periodontal status of PMC and ZC groups at 3 months, 1 year, and 2 years after treatment (P>0.05). However, the GI, BI, and PLI in the PMC group were higher than those in the ZC group at 3 months, 1 year, and 2 years after treatment, and the difference was dramatically significant (P<0.05). No significances difference existed in various prosthetic indices (P>0.05), as well as in the GI, BI, and PLI, between the two groups (P>0.05). No significant differences existed in various prosthetic indices between genders after PMC restoration (P>0.05). The scores of girls in various prosthetic indices after ZC restoration were higher than those of boys (P<0.05). Pearson correlation analysis indicated an inverse correlation between age in the PMC group and the GI, BI, PLI, and FDI indices (P<0.01), rather than in the ZC group (P>0.05). CONCLUSIONS: PMC and ZC can be applied to restore deciduous molar caries. The periodontal status of deciduous teeth in ZC group was superior to that in the PMC group. The periodontal status of deciduous teeth in PMC group may be stable with increased age.