Virucidal Coatings Active Against SARS-CoV-2.

Three types of coatings (contact-based, release-based, and combined coatings with both contact-based and release-based actions) were prepared and tested for the ability to inactivate SARS-CoV-2. In these coatings, quaternary ammonium surfactants were used as active agents since quaternary ammonium compounds are some of the most commonly used disinfectants. To provide contact-based action, the glass and silicon surfaces with covalently attached quaternary ammonium cationic surfactant were prepared using a dimethyloctadecyl[3-(trimethoxysilyl)propyl]ammonium chloride modifier. Surface modification was confirmed by attenuated total reflection infrared spectroscopy, X-ray photoelectron spectroscopy (XPS), scanning electron microscopy, and contact angle measurements. The grafting density of the modifier was estimated by XPS and elemental analysis. To provide release-based action, the widely used quaternary ammonium cationic disinfectant, benzalkonium chloride (BAC), and a newly synthesized cationic gemini surfactant, C18-4-C18, were bound non-covalently to the surface either through hydrophobic or electrostatic interactions. Virus titration revealed that the surfaces with combined contact-based and release-based action and the surfaces with only release-based action completely inactivate SARS-CoV-2. Coatings containing only covalently bound disinfectant are much less effective; they only provide up to 1.25 log10 reduction in the virus titer, probably because of the low disinfectant content in the surface monolayer. No pronounced differences in the activity between the flat and structured surfaces were observed for any of the coatings under study. Comparative studies of free and electrostatically bound disinfectants show that binding to the surface of nanoparticles diminishes the activity. These data indicate that SARS-CoV-2 is more sensitive to the free disinfectants.

Sustainable detergent-disinfectant agent based on whey mineralizate and silver nanoparticles for cleaner production in dairy industry.

Detergents and disinfectants for dairy industry must meet a variety of characteristics, including low toxicity, high antibacterial activity, and excellent rinsing of pollutants from working surfaces. This work presents an innovative detergent-disinfectant agent based on whey mineralizate and silver nanoparticles (Ag NPs), which allows reducing production costs and ensuring high cleanliness of treated surfaces compared to analogues. For this purpose, a method for obtaining sols of Ag NPs stabilized with didecyldimethylammonium bromide (Ag NPs-DDAB) was developed and optimized using neural network algorithms. Characterization of Ag NPs-DDAB showed particles with a radius of 4.5 nm and 20 nm, stable in the pH range from 2 to 11. An acute toxicity study of Ag NPs in mice showed LD50 = 4230 µg/kg. Based on the degree of accumulation and inhalation toxicity, Ag NPs-DDAB are classified as low-hazard chemicals. The developed detergent-disinfectant had a washability of about 90%, high antimicrobial activity (0.005 mg/mL) against Penicillium roqueforti and a sanitary and hygienic effect on coliforms, general contamination and pathogenic microorganisms, a low-corrosive effect and low toxicity (315 mg/mL) to Danio rerio. It was concluded that the use of detergent-disinfectant agent will completely eliminate the consumption of water for the equipment cleaning process and can be used to clean an electrodialysis unit's circuits, enabling the utilization of secondary waste from membrane milk processing and promoting resource efficiency and cleaner production in the dairy industry.

A Chemical Toolbox to Unveil Synthetic Nature-Inspired Antifouling (NIAF) Compounds.

The current scenario of antifouling (AF) strategies to prevent the natural process of marine biofouling is based in the use of antifouling paints containing different active ingredients, believed to be harmful to the marine environment. Compounds called booster biocides are being used with copper as an alternative to the traditionally used tributyltin (TBT); however, some of them were recently found to accumulate in coastal waters at levels that are deleterious for marine organisms. More ecological alternatives were pursued, some of them based on the marine organism mechanisms' production of specialized metabolites with AF activity. However, despite the investment in research on AF natural products and their synthetic analogues, many studies showed that natural AF alternatives do not perform as well as the traditional metal-based ones. In the search for AF agents with better performance and to understand which molecular motifs were responsible for the AF activity of natural compounds, synthetic analogues were produced and investigated for structure-AF activity relationship studies. This review is a comprehensive compilation of AF compounds synthesized in the last two decades with highlights on the data concerning their structure-activity relationship, providing a chemical toolbox for researchers to develop efficient nature-inspired AF agents.

Volatilization and disinfection efficacy of gaseous hypochlorous acid from an air washer-type humidifier in a large space.

An air washer-type humidifier has two useful functions: humidification, and air purification, and it applies to large indoor spaces. In this study, the efficacy of an air washer-type humidifier fed with 24 L of weakly acidic electrolyzed water（WAEW) at pH 5.0 and 30 mg/L in disinfecting attached bacteria and airborne microorganisms was studied in a 480 m3 indoor space. The humidifier was operated at a shower volume of 9.0 L/min of WAEW and at an air flow rate of 29 m3/min. Volatilization of gaseous hypochlorous acid（HOCl(g)) proceeded according to first-order kinetics during the 60 min of operation. Fresh WAEW was supplied to the humidifier every 60 min, and the HOCl(g) concentration in the indoor space was maintained within the range of 25-52 ppb for at least 180 min of operation. The number of viable bacterial cells on wet agar plates placed on the floor at a distance of 5-20 m away from the humidifier decreased by 2.0-3.0 log after 30 min of operation, and no viable cells were detected after 60 min of operation. A logarithmic reduction of more than 2.7 was achieved within 15 min against bacteria-attached plates placed at a 1.5 m-height position where the outlet airflow from the humidifier was directly exposed. This indicates that the disinfection efficacy of HOCl(g) volatilized from the humidifier depends on the rate of outlet airflow reaching the bacteria-attached plates. The number of viable airborne microorganisms decreased by approximately 54% after 180 min of operation. This study demonstrated that an air-washer-type humidifier can spread HOCl(g) evenly throughout a large indoor space and is effective in disinfecting attached bacteria and airborne microorganisms.

Enhanced electrolytic production of hypochlorous acid using phosphorus-modified carbon felt electrodes: A study in disinfectant synthesis.

In this study, we fabricated phosphorus-modified carbon felt electrode anodes for chloride oxidation in saline solutions to produce HClO via electrocatalysis, forming a compound fungicide saline applicable for debridement and disinfection. A low-cost phosphorus-modified carbon felt electrode (P@CF) with high chlorine evolution reaction activity was synthesized to address the reduced efficiency of CER and the solution's pH increase. Heteroatoms P and O were introduced into the carbon felt by phosphoric acid activation followed by heat treatment. The maximum active chlorine concentration on the P@CF electrode could reach 616.8 mg/L in 60 min under the optimal synthesis conditions of a phosphoric acid mass fraction of 30%, a phosphoric acid impregnation time of 3 h, and a heat treatment temperature of 300 °C. The active chlorine concentration was 1.8 times higher on the P@CF electrode compared to the original carbon felt electrode. The optimal reaction conditions for the generation of active chlorine were as follows: salt concentration of 9 g/L, voltage of 7 V, and electrode spacing of 2 cm as verified by response surfaces. This electrolysis reaction follows one-stage reaction kinetics. Subsequently, the disinfection efficacy of the produced disinfectants was examined. The prepared disinfectant was also compared to a commercially available hypochlorite disinfectant, showing similar disinfection effects on E. coli for both.

Engineered MXene/Bi2S3 nanoflowers in sodium alginate hydrogel: A synergistic eradicator of disinfected byproducts in aqueous environment.

In this work, Bi2S3 nanoflowers were in situ anchored on the surface of Ti3C2 via a hydrothermal process to obtain MXene-supported Ti3C2/Bi2S3 nanocomposite, then incorporated inside in sodium alginate polymer to prepared hydrogel materials (Ti3C2/Bi2S3@SA-H) which outperforms and have an excellent capability for the removal of pollutants like disinfected byproducts. The synthesized hydrogel material Ti3C2/Bi2S3@SA-H may be utilized for a variety of functional materials in environmental applications. Furthermore, the Ti3C2/Bi2S3@SA-H was characterized by SEM, EDX, XRD, BET, AFM, FTIR, Zeta potential, XPS, Raman and TGA. Remarkably, Ti3C2/Bi2S3@SA-H hydrogel 0.007 cm3 g-1, 159.5 nm and 0.0017 cm3 g-1, 160.5 nm materials exhibited the highest average pore diameter. The research focused on evaluating the adsorption capability of Ti3C2/Bi2S3@SA-H hydrogel materials for 2,6-dibromo-4-nitrophenol (DBNP), 2,4,6-triiodophenol (TIP), 2,4,6-Trichlorophenol (TCP) and 2,6-dichloro-4-nitrophenol (DCNP). The findings indicated that the material exhibited the eradication efficiency of about 662, 657, 647 and 617 mg/g from DBNP, TIP, TCP and DCNP respectively. Several adsorption isotherms were extensively examined, encompassing the Temkin, Langmuir and Freundlich models, alongside pseudo-first and second-order models. The Langmuir and pseudo-second-order models showed the highest degree of consistency with the observed data. Concerning regeneration and reusability, the materials demonstrated easy regeneration and effective recyclability over the course of 10 cycles. The notable adsorption capacity, coupled with the innovative combination of Ti3C2/Bi2S3 and polymer hydrogel, along with its recyclability, positions our material Ti3C2/Bi2S3@SA-H as a highly prospective competitors for wastewater treatment and other critical areas in water research.

TRPA1 nanovesicle-conjugated receptonics for rapid biocide screening.

Although biocides are important materials in modern society and help protect human health and the environment, increasing exposure to combined biocides can cause severe side effects in the human body, such as lung fibrosis. In this study, we developed a receptonics system to screen for biocides in combined household chemical products based on biocides. The system contains transient receptor potential ankyrin 1 (TRPA1) nanovesicles (NVs) to sense biocides based on pain receptors and a side-gated field-effect transistor (SGFET) using a single-layer graphene (SLG) micropattern channel. The binding affinities between the TRPA1 receptor and the various biocides were estimated by performing biosimulation and using a calcium ion (Ca2+) assay, and the sensitivity of the system was compared with that of TRPA1 NV receptonics systems. Based on the results of the TRPA1 NV receptonics system, the antagonistic and potentiation effects of combined biocides and household chemical products depended on the concentration. Finally, the TRPA1 NV receptonics system was applied to screen for biocides in real products, and its performance was successful. Based on these results, the TRPA1 NV receptonics system can be utilized to perform risk evaluations and identify biocides in a simple and rapid manner.

Formation of the emerging disinfection byproducts halocyclopentadienes from phenolic compounds after chlorination.

Halocyclopentadienes (HCPDs) are an emerging class of alicyclic disinfection by-products (DBPs) with high toxicity in disinfected drinking water. However, their potential precursors remain unclear, which hinders the understanding of their formation and further development of control strategies. In this study, two HCPDs, 1,2,3,4-tetrachloro-1,3-cyclopentadiene (TCC) and 1,2,3,4,5,5-hexachloro-1,3-cyclopentadiene (HCC), were identified in chlorinated lignin and tannic acid samples for the first time. The chlorination of four lignin-like and two tannic-like phenolic model compounds confirmed that guaiacol and digallic acid can produce HCPDs. According to their structures, ortho-substituents of phenolic compounds were speculated to be crucial for HCPDs formation. The simulated disinfection of catechol, 2-ethoxyphenol (2-EOP), 2-propoxyphenol (2-POP) and 3,4-dihydroxy-5-methoxybenzoic acid (DH-5-MBA) with different ortho-substituents demonstrated that three of these compounds can generate HCPDs, except catechol, which further indicates that ortho-substituents, such as the methoxy, ethoxy and propoxy groups, contribute to HCPDs generation. Guaiacol was the simplest compound for generating HCPDs, and possible formation pathways during chlorination were proposed. Seven hydroxy-chlorocyclopentadienes were tentatively identified and are likely important intermediates of HCPDs formation. Additionally, TCC and HCC were confirmed in tap water and chlorinated SRNOM samples with total concentrations up to 11.07 ng/L and 65.66 ng/L, respectively, further demonstrating the wide existence of HCPDs and their precursors. This study reports the clear precursors of HCPDs and provides a theoretical foundation for controlling HCPDs formation in disinfected drinking water.

Biocide physically cross-linked hydrogels based on carrageenan and guanidinium polyampholytes for wound healing applications.

Over last years, hydrogels based on natural polymers have attracted considerable interest as materials for wound healing. Herein, hydrogel films based on kappa-carrageenan and guanidinium polyampholytes were prepared by the in situ physical cross-linking with potassium chloride and borax, respectively. The polyampholytes were obtained by a free radical copolymerization of 2,2-diallyl-1,1,3,3-tetraethylguanidinium chloride and unsaturated acids. To characterize the composite films, NMR, FTIR, SEM, TGA, XRD, element analysis and tensile test were used. Ampicillin was incorporated into the hydrogels to enhance wound healing potential. The healing-related characteristics, including swelling ratio, drug release and antimicrobial activity, were assessed. The equilibrium swelling ratios were in the range of 3.9-6.5 depending on the polyampholyte composition. According to the in vitro ampicillin release studies, 30-43 % of ampicillin was released from the hydrogels after 5 h at 37 °C and pH 7.4, with drug release being temperature and pH dependent. The ampicillin-loaded films showed a remarkable antimicrobial effect. The inhibition sizes for Escherichia coli and Staphylococcus aureus were 1.10-1.85 and 1.95-2.60 cm, respectively. Although the bi-polymeric hydrogels were thoroughly characterized, with the in vitro study of their biocidal effects carried out in this work, the in vivo drug release assessment needs to be further explored.

Fate and transport of chlorine dioxide: Modeling chlorine dioxide in water distribution systems.

This study aims to conduct a comprehensive analysis of switching disinfectants from sodium hypochlorite bleach to chlorine dioxide (ClO2) in the water distribution system of Geyikbayiri, Antalya. For this purpose, bulk decay rates of ClO2 at various water temperatures were determined in laboratory studies. The study revealed ClO2 bulk decay rates of 0.12639 day-1, 0.17848 day-1, and 0.19621 day-1 at temperatures 15°C, 20°C, and 30°C, respectively. The EPANET, a widely employed computer program for simulating the extended-period behavior of hydraulic and water quality in pressurized pipes, was utilized for the analysis of the fate and transport of ClO2. A hydraulic model was first developed, calibrated, and verified using distinct data sets. The Hazen-Williams friction coefficient of the PSA was determined to be 120 by the trial-and-error method with a mean absolute error (MAE) of 0.408 m. A ClO2 model was then integrated with the calibrated and verified hydraulic model, revealing a wall decay rate of 0.01 m/day and an average MAE of 0.034 mg/l. After calibration and verification of the ClO2 model, several management scenarios were developed, and ClO2 dosing rates were determined. The study showed that ClO2 dosing rates of 0.40 mg/l and 0.45 mg/l should be applied to keep ClO2 concentrations within certain limits. PRACTITIONER POINTS: Disinfectants must maintain a sufficient residual in water distribution systems. Chlorine dioxide requires less contact time and is not affected by pH fluctuations. Modeling serves as a decision-making tool for the management of disinfectants. Bulk and wall decay rates of chlorine dioxide are crucial for management strategies. Chlorine dioxide is a good alternative as a disinfectant in such systems.

Probing the toxic hypochlorous acid in natural waters and biosystem by a coumarin-based fluorescence probe.

Since the onset of the SARS-CoV-2 pandemic in early 2020, there has been a notable rise in sodium hypochlorite disinfectants. Sodium hypochlorite undergoes hydrolysis to generate hypochlorous acid for virus eradication. This chlorine-based disinfectant is widely utilized for public disinfection due to its effectiveness. Although sodium hypochlorite disinfection is convenient, its excessive and indiscriminate use can harm the water environment and pose a risk to human health. Hypochlorous acid, a reactive oxygen species, plays a crucial role in the troposphere, stratospheric chemistry, and oxidizing capacity. Additionally, hypochlorous acid is vital as a reactive oxygen species in biological systems, and its irregular metabolism and level is associated with several illnesses. Thus, it is crucial to identify hypochlorous acid to comprehend its environmental and biological functions precisely. Here, we constructed a new fluorescent probe, utilizing the twisted intramolecular charge transfer mechanism to quickly and accurately detect hypochlorous acid in environmental water and biosystems. The probe showed a notable increase in fluorescence when exposed to hypochlorous acid, demonstrating its excellent selectivity, fast response time (less than 10 seconds), a large Stokes shift (∼ 102 nm), and a low detection limit of 15.5 nM.

Control of Aromatic Disinfection Byproducts in Potable Reuse Water by the UV222/H2O2 vs UV254/H2O2 Advanced Oxidation Processes.

Research has demonstrated the difficulty associated with degrading the conventional 1-2 carbon aliphatic halogenated byproducts of disinfectant reactions with organic matter [disinfection byproducts (DBPs)] within advanced oxidation process (AOP) units in potable reuse trains, but the efficacy of AOP units for treating the emerging classes of halogenated aromatic DBPs is unclear. We herein demonstrate more effective removal of 28 halogenated aromatic DBPs in the UV/H2O2 AOP at 222 nm (UV222) than in the conventional UV/H2O2 AOP at 254 nm. Direct photolysis of 28 halogenated aromatic DBPs was greatly enhanced at 222 nm with fluence-based photodecay rate constants of 4.31 × 10-4-1.53 × 10-2 cm2 mJ-1, which was mainly attributed to the higher molar absorption coefficients of halogenated aromatic DBPs at 222 nm than 254 nm. Generally, quantum yields of halogenated aromatic DBPs at both 222 and 254 nm followed the order of halophenols > halohydroxybenzaldehydes > halonitrophenols. All 28 halogenated aromatic DBPs exhibit high reactivity toward HO• with second-order rate constants ranging from 2.18 × 109 to 1.15 × 1010 M-1 s-1 determined by X-ray radiolysis. The UV fluence required to achieve 90% loss of halogenated aromatic DBPs in the UV222/H2O2 AOP was 75-95% lower than that in the UV254/H2O2 AOP, and 90% removal of most tested halogenated aromatic DBPs can be achieved in the UV222/H2O2 AOP within the UV fluence levels commonly applied in potable reuse (700-1000 mJ cm-2).

Biocompatible hydrogels based on quaternary ammonium salts of chitosan with high antimicrobial activity as biocidal agents for disinfection.

The paper reports new hydrogels based on quaternary ammonium salts of chitosan designed as biocidal products. The chitosan derivative was crosslinked with salicylaldehyde via reversible imine bonds and supramolecular self-assemble to give dynamic hydrogels which respond to environmental stimuli. The crosslinking mechanism was demonstrated by 1H NMR and FTIR spectroscopy, and X-ray diffraction and polarized light microscopy. The hydrogel nature, self-healing and thixotropy were proved by rheological investigation and visual observation, and their morphology was assessed by scanning electron microscopy. The relevant properties for application as biocidal products, such as swelling, dissolution, bioadhesiveness, antimicrobial activity and ex-vivo hemocompatibility and in vivo local toxicity and biocompatibility on experimental mice were measured and analyzed in relationship with the imination degree and the influence of each component. It was found that the hydrogels are superabsorbent, have good adhesivity to skin and various surfaces and antimicrobial activity against relevant gram-positive and gram-negative bacteria, while being hemocompatible and biocompatible. Besides, the hydrogels are easily biodegraded in soil. All these properties recommend the studied hydrogels as ecofriendly biocidal agents for living tissues and surfaces, but also open the perspectives of their use as platform for in vivo applications in tissue engineering, wound healing, or drug delivery systems.

[An in vitro experiment on the stability and irritant of hypochlorous acid in oral cavity].

PURPOSE: To study the stability of physicochemical properties and sterilizing effect about two commercially available hypochlorous acid (HClO) products under simulated clinical conditions, and to evaluate the compatibility of HClO on soft and hard tissues and cells in oral cavity. METHODS: Samples of HClO solution with different production processes were prepared, to detect the changes of physicochemical indexes of each sample over time under simulated clinical conditions (shielded from light at 20-25 ℃, open the cover for 5 minutes every day), including free available chlorine, oxidation-reduction potential and pH. Through suspension quantitative germicidal test, the antibiosis-concentration curve of HClO solution was made, so as to calibrate the change of antibacterial ability of disinfectant with the decrease of available chlorine content during storage. Pulp, tongue and dentine were immersed in PBS, 100 ppm HClO, 200 ppm HClO and 3% NaClO. The influence on soft and hard tissues was evaluated by weighing method and microhardness test. The toxic effects of HClO, NaClO and their 10-fold diluent on human gingival fibroblasts were determined by CCK-8 cytotoxicity assay. GraphPad PRIS 8.0 software was used to analyze the data. RESULTS: Under simulated conditions, the free available chlorine (FAC) of HClO solution decayed with time, and the attenuation degree was less than 20 ppm within 1 month. The bactericidal effect of each HClO sample was still higher than 5log after concentration decay. There was no obvious dissolution and destruction to soft and hard tissues for HClO(P＞0.05). The cell viability of HClO to human gingival fibroblast cells (HGFC) was greater than 80%, which was much higher than 3% NaClO (P＜0.001). CONCLUSIONS: The bactericidal effect and stability of HClO solution can meet clinical needs, which has low cytotoxicity and good histocompatibility. It is expected to become a safe and efficient disinfection product in the field of living pulp preservation and dental pulp regeneration.

Relationship between chlorine decay and nanobubble application in secondary treated wastewater.

There has been numerous research on the uses of treated wastewater that needs chlorine disinfection, but none have looked at the impacts of injecting nanobubbles (NBs) on the decomposition of residual chlorine. Gas NB injection in treated wastewater improves its properties. The kinetics of disinfectant decay could be impacted by changes in treated wastewater properties. This paper studies the effect of various NB injections on the residual chlorine decay of secondary treated wastewater (STWW). It also outlines the empirical equations that were developed to represent these impacts. The results show that each type of NBs in treated wastewater had a distinct initial chlorine concentration. The outcomes demonstrated a clear impact on the decrease of the needed chlorine quantity and the reduction of chlorine decay rate when utilizing NB injection for the STWW. As a result, the residual chlorine will remain for a longer time and will resist any microbiological growth under the application of NBs on treated wastewater. Moreover, NBs in secondary treated effluent reduce chlorine usage, lowering wastewater disinfection costs.

Natural pyrite and ascorbic acid co-enhance periodate activation for inactivation of antibiotic resistant bacteria and inhibition of resistance genes transmission: A green disinfection process dominated by singlet oxygen.

The transmission of antibiotic resistance genes (ARGs) and the propagation of antibiotic resistant bacteria (ARB) threaten public health security and human health, and greener and more efficient disinfection technologies are expected to be discovered for wastewater treatment. In this study, natural pyrite and ascorbic acid (AA) were proposed as environmental-friendly activator and reductant for periodate (PI) activation to inactivate ARB. The disinfection treatment of PI/pyrite/AA system could inactivate 5.62 log ARB within 30 min, and the lower pH and higher PI and natural pyrite dosage could further boost the disinfection efficiency. The 1O2 and SO4•- were demonstrated to be crucial for the inactivation of ARB in PI/pyrite/AA system. The disinfection process destroyed the morphological structure of ARB, inducing oxidative stress and stimulating the antioxidant system. The PI/pyrite/AA system effectively reduced the intracellular and extracellular DNA concentration and ARGs abundance, inhibiting the propagation of ARGs. The presence of AA facilitated the activation of PI with natural pyrite and significantly increased the concentration of Fe2+ in solution. The reusability of natural pyrite, the safety of the disinfection by-products and the inhibition of ARB regeneration indicated the application potential of PI/pyrite/AA system in wastewater disinfection.

Effects of UV light on physicochemical changes in thermoplastic polyurethanes: Mechanism and disinfection byproduct formation.

The presence of microplastics (MPs) products and particles in the environment can significantly impact the human body. Most MPs that enter the environment also enter the water cycle. During sunlight light irradiation (especially ultraviolet (UV) part) or UV disinfection, many of these MPs, particularly those rich in surface functional groups like thermoplastic polyurethanes (TPU), undergo physicochemical changes that can affect the formation of disinfection byproducts (DBPs). This study investigates the physicochemical changes of TPU in water after exposure to UV irradiation and incubation in the dark, as well as the formation of DBPs after chlorination. The results show that TPU undergo chain breakage, oxidation, and cross-linking when exposed to UV irradiation in an aqueous system. This leads to fragmentation into smaller particles, which facilitates the synthesis of DBPs. Subsequent research has demonstrated that the TPU leaching solution produces a significantly higher DBP content than the chlorination of TPU MPs, particularly at high concentrations of CHCl3. Therefore, it is important to give greater consideration to the soluble DBP precursors released by TPU.

Unexpected weakened formation of disinfection byproducts and enhanced production of halates by cupric oxide during chlorination of peptide-bound aspartic acid.

Under the condition that the residual chlorine is guaranteed, the biofilm still thrives in drinking water distribution systems through secreting a large number of extracellular polymeric substances (EPS), in which protein components are the primary precursor of disinfection byproducts (DBPs), mostly in the form of combined amino acids. The aim of this study is to investigate the action of CuO on the formation of halates (XO3-, ClO3- and BrO3-) and DBPs (trihalomethanes, THMs; haloacetonitriles, HANs) with aspartic acid tetrapeptide (TAsp) as protein surrogate. The presence of CuO promoted the self-decay rather than TAsp-induced decay of oxidants, resulting in an increase in XO3- yield and a decrease in DBPs yield. It was CuO-induced weaker production of cyanoacetic acid and 3-oxopropanoic acid that induced the decreased yields of HANs and THMs, respectively. The FTIR and Raman spectra indicate a weak complexation between CuO and TAsp. Given this, the CuO-HOX/OX- complexes were inferred to be reactive to HOX/OX- but less reactive to TAsp. The study helps to better understand the formation of XO3- and DBPs during the chlorination of EPS, and propose precise control strategies when biofilm boosts in water pipes.

An effective and rapidly degradable disinfectant from disinfection byproducts.

Chloroxylenol is a worldwide commonly used disinfectant. The massive consumption and relatively high chemical stability of chloroxylenol have caused eco-toxicological threats in receiving waters. We noticed that chloroxylenol has a chemical structure similar to numerous halo-phenolic disinfection byproducts. Solar detoxification of some halo-phenolic disinfection byproducts intrigued us to select a rapidly degradable chloroxylenol alternative from them. In investigating antimicrobial activities of disinfection byproducts, we found that 2,6-dichlorobenzoquinone was 9.0-22 times more efficient than chloroxylenol in inactivating the tested bacteria, fungi and viruses. Also, the developmental toxicity of 2,6-dichlorobenzoquinone to marine polychaete embryos decreased rapidly due to its rapid degradation via hydrolysis in receiving seawater, even without sunlight. Our work shows that 2,6-dichlorobenzoquinone is a promising disinfectant that well addresses human biosecurity and environmental sustainability. More importantly, our work may enlighten scientists to exploit the slightly alkaline nature of seawater and develop other industrial products that can degrade rapidly via hydrolysis in seawater.

In Silico Assessment of Chemical Disinfectants on Surface Proteins Unveiled Dissimilarity in Antiviral Efficacy and Suitability towards Pathogenic Viruses.

Viral pathogens pose a substantial threat to public health and necessitate the development of effective remediation and antiviral strategies. This short communication aimed to investigate the antiviral efficacy of disinfectants on the surface proteins of human pathogenic viruses. Using in silico modeling, the ligand-binding energies (LBEs) of selected disinfectants were predicted and combined with their environmental impacts and costs through an eco-pharmaco-economic analysis (EPEA). The results revealed that the binding affinities of chemical disinfectants to viral proteins varied significantly (p < 0.005). Rutin demonstrated promising broad-spectrum antiviral efficacy with an LBE of -8.49 ± 0.92 kcal/mol across all tested proteins. Additionally, rutin showed a superior eco-pharmaco-economic profile compared to the other chemicals, effectively balancing high antiviral effectiveness, moderate environmental impact, and affordability. These findings highlight rutin as a key phytochemical for use in remediating viral contaminants.