[Oblique Lumbar Interbody Fusion Combined With 4-Screw Fixation for Treating Two-Level Degenerative Lumbar Diseases:A Finite Element Study].

Objective To demonstrate the feasibility of oblique lumbar interbody fusion (OLIF) combined with 4-screw fixation for treating two-level lumbar degenerative diseases.Methods An intact finite element model of L3-S1 (M0) was constructed and validated.Then,we constructed the M1 model by simulating OLIF surgery at L3/4 and L4/5 segments on the M0 model.By attachment of posterior 4-screw or 6-screw fixation to the M1 model,three 4-screw fixation models (M2-M4) and one 6-screw fixation model (M5) were established.The segmental and overall range of motion (ROM) and the peak von Mises stresses of superior endplate,cage,and posterior screw-rod were investigated under each implanted condition.Results Under the motion modes of forward flexion,backward extension,bilateral (left and right) flexion,and left and right rotation,the L3/4 ROM of M2 model and L4/5 ROM of M3 model increased,while the L3/4 and L4/5 ROM of M4 and M5 models significantly decreased compared with those of M1 model.Under all motion modes,the L4 superior endplate in M2 model and the L5 superior endplate in M3 model showed the maximum peak von Mises stress,and the peak von Mises stresses of L4 and L5 superior endplates in M4 and M5 models were close.The L3/4 cage in M2 model and the L4/5 cage in M3 model showcased the largest peak von Mises stress,and the peak von Mises stresses of cages in M4 and M5 models were close.The peak stresses of internal fixation in M2-M5 models were close.Conclusion Four-screw fixation can replace 6-screw fixation in the OLIF surgery for treating two-level degenerative lumbar diseases.

Biomechanical Design Optimization of Distal Humerus Fracture Plates: A Review.

The goal of this article was to review studies on distal humerus fracture plates (DHFPs) to understand the biomechanical influence of systematically changing the plate or screw variables. The problem is that DHFPs are commonly used surgically, although complications can still occur, and it is unclear if implant configurations are always optimized using biomechanical criteria. A systematic search of the PubMed database was conducted to identify English-language biomechanical optimization studies of DHFPs that parametrically altered plate and/or screw variables to analyze their influence on engineering performance. Intraarticular and extraarticular fracture (EAF) data were separated and organized under commonly used biomechanical outcome metrics. The results identified 52 eligible DHFP studies, which evaluated various plate and screw variables. The most common plate variables evaluated were geometry, hole type, number, and position. Fewer studies assessed screw variables, with number and angle being the most common. However, no studies examined nonmetallic materials for plates or screws, which may be of interest in future research. Also, articles used various combinations of biomechanical outcome metrics, such as interfragmentary fracture motion, bone, plate, or screw stress, number of loading cycles to failure, and overall stiffness (Os) or failure strength (Fs). However, no study evaluated the bone stress under the plate to examine bone "stress shielding," which may impact bone health clinically. Surgeons treating intraarticular and extraarticular distal humerus fractures should seriously consider two precontoured, long, thick, locked, and parallel plates that are secured by long, thick, and plate-to-plate screws that are located at staggered levels along the proximal parts of the plates, as well as an extra transfracture plate screw. Also, research engineers could improve new studies by perusing recommendations in future work (e.g., studying alternative nonmetallic materials or "stress shielding"), clinical ramifications (e.g., benefits of locked plates), and study quality (e.g., experimental validation of computational studies).

Pars interarticularis screws for posterior cervical fusion - investigating a new trajectory using a CT-based multiplanar reconstruction: Part I.

BACKGROUND: Lateral mass screw fixation is the standard for posterior cervical fusion between C3 and C6. Traditional trajectories stabilize but carry risks, including nerve root and vertebral artery injuries. Minimally invasive spine surgery (MISS) is gaining popularity, but trajectories present anatomical challenges. RESEARCH QUESTION: This study proposes a novel pars interarticularis screw trajectory to address these issues and enhance in-line instrumentation with cervical pedicle screws. MATERIALS AND METHODS: A retrospective analysis of reformatted cervical CT scans included 10 patients. Measurements of the pars interarticularis morphology were performed on 80 segments (C3-C6). Two pars interarticularis screw trajectories were evaluated: Trajectory A (upper outer quadrant entry, horizontal trajectory) and Trajectory B (lower outer quadrant entry, cranially pointed trajectory). These were compared to standard lateral mass and cervical pedicle screw trajectories, assessing screw lengths, angles, and potential risks to the spinal canal and transverse foramen. RESULTS: Trajectory B showed significantly longer pars lengths (15.69 ± 0.65 mm) compared to Trajectory A (12.51 ± 0.24 mm; p < 0.01). Lateral mass screw lengths were comparable to pars interarticularis screw lengths using Trajectory B. Both trajectories provided safe angular ranges, minimizing the risk to delicate structures. DISCUSSION: and Conclusion. Pars interarticularis screws offer a viable alternative to lateral mass screws for posterior cervical fusion, especially in MISS contexts. Trajectory B, in particular, presents a feasible and safe alternative, reducing the risk of vertebral artery and spinal cord injury. Preoperative assessment and intraoperative technologies are essential for successful implementation. Biomechanical validation is needed before clinical application.

Combining robotics and 3D printing facilitates closed reduction of humeral shaft fractures using a minimally invasive plate as a reduction template: A proof-of-concept study.

BACKGROUND: Minimally invasive percutaneous plate osteosynthesis for humeral shaft fractures (HSFs) has limitations due to malreduction and radiation exposure. To address these limitations, we integrated robotics and 3D printing by incorporating plates as reduction templates. METHOD: The innovative technology facilitated closed reduction of HSFs in the operating theatre using 18 models with cortical marking holes. The dataset of the precontoured plate was imported into 3D planning software for virtual fixation and screw path planning. The models were divided into half to simulate transverse fractures. During the operation, the software generated drilling trajectories for robot navigation, and precise plate installation achieved automatic fracture reduction. RESULTS: The evaluation results of reduction accuracy revealed variations in length, apposition, alignment, and rotation that meet the criteria for anatomic reduction. High interoperator reliabilities were observed for all parameters. CONCLUSIONS: The proposed technology achieved anatomic reduction in simulated bones.

Evaluating three internal fixation techniques for Pauwels III femoral neck fractures via finite element analysis.

The selection of implants for fixing unstable femoral neck fractures (FNF) remains contentious. This study employs finite element analysis to examine the biomechanics of treating Pauwels type III femoral neck fractures using cannulated compression screws (3CS), biplane double-supported screw fixation (BDSF), and the femoral neck system (FNS). A three-dimensional model of the proximal femur was developed using computed tomography scans. Fracture models of the femoral neck were created with 3CS, BDSF, and FNS fixations. Von Mises stress on the proximal femur, fracture ends, internal fixators, and model displacements were assessed and compared across the three fixation methods (3CS, BDSF, and FNS) during the heel strike of normal walking. The maximum Von Mises stress in the proximal fragment was significantly higher with 3CS fixation compared to BDSF and FNS fixations (120.45 MPa vs. 82.44 MPa and 84.54 MPa, respectively). Regarding Von Mises stress distribution at the fracture ends, the highest stress in the 3CS group was 57.32 MPa, while BDSF and FNS groups showed 51.39 MPa and 49.23 MPa, respectively. Concerning implant stress, the FNS model exhibited greater Von Mises stress compared to the 3CS and BDSF models (236.67 MPa vs. 134.86 MPa and 140.69 MPa, respectively). Moreover, BDSF displayed slightly lower total displacement than 3CS fixation (7.19 mm vs. 7.66 mm), but slightly higher displacement than FNS (7.19 mm vs. 7.03 mm). This study concludes that BDSF outperforms 3CS fixation in terms of biomechanical efficacy and demonstrates similar performance to the FNS approach. As a result, BDSF stands as a dependable alternative for treating Pauwels type III femoral neck fractures.

Clinical study on freehand of bicortical sacral screw fixation with the assistance of torque measurement device.

BACKGROUND: Sacral screw loosening is a typical complication after internal fixation surgery through the vertebral arch system. Bicortical fixation can successfully prevent screw loosening, and how improving the rate of bicortical fixation is a challenging clinical investigation. OBJECTIVE: To investigate the feasibility of improving the double corticality of sacral screws and the optimal fixation depth to achieve double cortical fixation by combining the torque measurement method with bare hands. METHODS: Ninety-seven cases of posterior lumbar internal fixation with pedicle root system were included in this study. Based on the tactile feedback of the surgeon indicating the expected penetration of the screw into the contralateral cortex of the sacrum, the screws were further rotated by 180°, 360°, or 720°, categorized into the bicortical 180° group, bicortical 360° group, and bicortical 720° group, respectively. Intraoperatively, the torque during screw insertion was recorded. Postoperatively, the rate of double-cortex engagement was evaluated at 7 days, and screw loosening was assessed at 1 year follow-up. RESULTS: The bicortical rates of the 180° group, 360° group, and 720° group were 66.13%, 91.18% and 93.75%, respectively. There were statistically significant differences between the 180° group and both the 360° and 720° groups (P < 0.05). However, there was no statistically significant difference between the 360° group and the 720° group (P > 0.05).The rates of loosening of sacral screws in the 180° group, 360° group, and 720° group were 20.97%, 7.35% and 7.81%, respectively. There were statistically significant differences between the 180° group and both the 360° and 720° groups (P < 0.05). However, there was no statistically significant difference between the 360° group and the 720° group (P > 0.05). The bicortical 360° group achieved a relatively satisfactory rate of dual cortical purchase while maintaining a lower rate of screw loosening. CONCLUSION: Manual insertion of sacral screws with the assistance of a torque measurement device can achieve a relatively satisfactory dual cortical purchase rate while reducing patient hospitalization costs.

Optimal Fixation Strategies for Displaced Femoral Neck Fractures in Patients 18-59 Years of Age: An Analysis of 565 Cases Treated at 26 Level 1 Trauma Centers.

OBJECTIVES: The objective of this study was to determine the difference in failure rates of surgical repair for displaced femoral neck fractures in patients younger than 60 years of age according to fixation strategy. DESIGN: This is a retrospective, comparative cohort study. SETTING: Twenty-six Level 1 North American trauma centers. PATIENT SELECTION CRITERIA: Patients younger than 60 years of age with a displaced femoral neck fracture (OTA 31-B2, B3) undergoing surgical repair from 2005 to 2017. OUTCOME MEASURES AND COMPARISONS: Patient demographics, injury characteristics, repair methods used, and treatment failure (nonunion/failed fixation, avascular necrosis, and need for secondary surgery) were compared according to fixation strategy. RESULTS: Five hundred and sixty-five patients met inclusion criteria and were studied. The mean age was 42 years, 36% were female, and the average Pauwels' angle of fractures was 55 degrees. There were 305 patients treated with multiple cannulated screws (MCS) and 260 treated with a fixed-angle (FA) construct. Treatment failures were 46% overall, but was more likely to occur in MCS constructs versus FA devices (55% vs. 36%, P < 0.001). When FA constructs were substratified, the use of a sliding hip screw with addition of a medial femoral neck buttress plate (FNBP) and "antirotation" (AR) screw demonstrated better results than either FNBP or AR screw alone or neither with the lowest overall construct failure rate of 11% (P < 0.036). CONCLUSIONS: Historically used fixation constructs for femoral neck fractures (eg, multiple cannulated screws and sliding hip screw) in young and middle-aged adults performed poorly compared with more recently proposed constructs, including those using a medial femoral neck buttress plate and an antirotation screw. Fixed-angle constructs outperformed multiple cannulated screws overall, and augmentation of fixed-angle constructs with a medial femoral neck buttress plate and antirotation screw improved the likelihood of successful treatment. Surgeons should prioritize fixation decisions when repairing displaced femoral neck fractures in patients. LEVEL OF EVIDENCE: Therapeutic Level III. See Instructions for Authors for a complete description of levels of evidence.

Clinical and Radiographic Results After Treatment of Traumatic Syndesmotic Instability Using a Novel Screw-Suture Syndesmotic Fixation Device.

OBJECTIVES: The objective of this study was to report early outcomes of a novel screw-suture syndesmotic device compared with suture button fixation devices when treating traumatic syndesmotic instability. DESIGN: Retrospective chart review. SETTING: Single academic Level 1 Trauma Center. PATIENT SELECTION CRITERIA: All adult patients who had syndesmotic fixation with the novel device [novel syndesmotic repair implant (NSRI) group] compared with a suture button device (SB group) between January 2018 and December 2022. OUTCOME MEASURES AND COMPARISONS: Medial clear space and tibiofibular overlap measurements were compared immediately postoperatively and at the final follow-up. Patients were followed for a minimum of 1 year or skeletal healing. RESULTS: Fifty-nine patients (25 female) with an average age of 47 years (range 19-78 years) were in the NSRI group compared with 52 patients (20 female) with an average age of 41 years (range 18-73 years) in the SB group. There were no significant differences when comparing body mass index, diabetes, or smoking status between groups (P > 0.05). There was no difference when comparing the postoperative and final medial clear space measurements in the NSRI group compared with the SB group (P = 0.86; 95% confidence interval, -0.32 to 0.27). There was no difference when comparing the postoperative and final tibiofibular overlap measurements in the NSRI group compared with the SB group (P = 0.79; 95% confidence interval, -0.072 to 0.09). There were 3 cases of implant removal in the NSRI group compared with 2 in the SB group (P = 0.77). There was 1 failure in the NSRI group and none in the SB group. The remaining patients were all fully ambulatory at the final follow-up (P = 0.35). CONCLUSIONS: A novel screw-suture syndesmotic implant provides the fixation of a screw, and the flexibility of a suture had similar radiographic outcomes compared with suture button fixation devices in treating ankle syndesmotic instability. LEVEL OF EVIDENCE: Therapeutic Level III. See Instructions for Authors for a complete description of levels of evidence.

Biomechanical evaluation of different medial column fixation patterns for valgus pilon fractures.

BACKGROUND: The purpose of this study was to perform a biomechanical analysis to compare different medial column fixation patterns for valgus pilon fractures in a case-based model. METHODS: Based on the fracture mapping, 48 valgus pilon fracture models were produced and assigned into four groups with different medial column fixation patterns: no fixation (NF), K-wires (KW), intramedullary screws (IS), and locking compression plate (LCP). Each group contained wedge-in and wedge-out subgroups. After fixing each specimen on the machine, gradually increased axial compressive loads were applied with a load speed of one millimeter per minute. The maximum peak force was set at 1500 N. Load-displacement curves were generated and the axial stiffness was calculated. Five different loads of 200 N, 400 N, 600 N, 800 N, 1000 N were selected for analysis. The specimen failure was defined as resultant loading displacement over 3 mm. RESULTS: For the wedge-out models, Group-IS showed less displacement (p < 0.001), higher axial stiffness (p < 0.01), and higher load to failure (p < 0.001) than Group-NF. Group-KW showed comparable displacement under loads of 200 N, 400 N and 600 N with both Group-IS and Group-LCP. For the wedge-in models, no statistical differences in displacement, axial stiffness, or load to failure were observed among the four groups. Overall, wedge-out models exhibited less axial stiffness than wedge-in models (all p < 0.01). CONCLUSIONS: Functional reduction with stable fixation of the medial column is essential for the biomechanical stability of valgus pilon fractures and medial column fixation provides the enough biomechanical stability for this kind of fracture in the combination of anterolateral fixation. In detail, the K-wires can provide a provisional stability at an early stage. Intramedullary screws are strong enough to provide the medial column stability as a definitive fixation. In future, this technique can be recommended for medial column fixation as a complement for holistic stability in high-energy valgus pilon fractures.

Evaluation of the clinical efficacy of using an inverted triangular cannulated compression screw in combination with positive or negative buttress reduction for the healing of femoral neck fractures.

OBJECTIVE: We aimed to compare the clinical efficacy of inverted triangular cannulated compression screws combined with Gotfried positive or negative buttress reduction in the healing of femoral neck fractures. METHODS: Between October 2017 and March 2021, 55 patients with femoral neck fractures underwent treatment using inverted triangular cannulated compression screws combined with Gotfried positive or negative buttress reduction. Among these patients, 29 received inverted triangular cannulated compression screws combined with Gotfried positive buttress reduction treatment. This group consisted of 16 males and 13 females, with an average age of 43.45 ± 8.23 years. Additionally, 26 patients received inverted triangular cannulated compression nails combined with Gotfried negative buttress reduction treatment. This group included 14 males and 12 females, with an average age of 41.96 ± 8.69 years. Postsurgery, various measurements were taken, including the degree of shortening of the femoral neck, degree of bone nonunion, degree of fixation failure, degree of ischemic necrosis of the femoral head, and Harris score of the hip joint. RESULTS: All patients were followed up for a minimum of 18 months. The group that underwent treatment with an inverted triangular cannulated compression screw combined with Gotfried positive buttress reduction did not experience any cases of bone nonunion, fixation failure, or ischemic necrosis of the femoral head. In the group that received treatment with inverted triangle cannulated compression screws combined with Gotfried negative buttress reduction, there was one case of bone nonunion, three cases of early fixation failure, and one case of ischemic necrosis. Ultimately, five patients (19.23% of the total) underwent joint replacement surgery. The average shortening lengths in the vertical plane were 4.07 ± 1.98 mm and 8.08 ± 3.54 mm, respectively. In the horizontal plane, the average shortening lengths were 3.90 ± 1.57 mm and 7.77 ± 3.31 mm, respectively. At the last follow-up, the group that received Gotfried positive buttress reduction had a greater Harris hip joint score. CONCLUSION: The success rate of combining inverted triangular cannulated compression screws with Gotfried positive buttress reduction surgery is relatively high. This surgical approach effectively prevents femoral neck shortening and improves hip joint function. Moreover, it is crucial to avoid negative buttress reduction when managing femoral neck fractures.

Experimental study on the biomechanical stability of complex acetabular fractures in the quadrilateral area: application of a dynamic anterior titanium-plate screw system.

BACKGROUND AND OBJECTIVE: Complex acetabular fractures involving quadrilateral areas are more challenging to treat during surgery. To date, there has been no ideal internal fixation for these acetabular fractures. The purpose of this study was to evaluate the biomechanical stability of complex acetabular fractures using a dynamic anterior titanium-plate screw system of the quadrilateral area (DAPSQ) by simulating the standing and sitting positions of pelvic specimens. MATERIALS AND METHODS: Eight formal in-preserved cadaveric pelvises aged 30-50 years were selected as the research objects. First, one hip of the normal pelvises was randomly used as the control model (group B) for measurement, and then one hip of the pelvises was randomly selected to make the fracture model in the 8 intact pelvises as the experimental model (group A) for measurement. In group A, acetabular both-column fractures in the quadrilateral area were established, and the fractures were fixed by DAPSQ. The biomechanical testing machine was used to load (simulated physiological load) from 400 N to 700 N at a 1 mm/min speed for 30 s in the vertical direction when the specimens were measured at random in simulated standing or sitting positions in groups. The horizontal displacement and longitudinal displacement of the acetabular fractures in the quadrilateral area were measured in both the standing and sitting simulations. RESULTS: As the load increased, no dislocation or internal fixation breakage occurred during the measurements. In the standing position, the horizontal displacement of the quadrilateral area fractures in group A and group B appeared to be less than 1 mm with loads ranging from 400 N to 700 N, and there was no significant difference between group A and group B (p > 0.05). The longitudinal displacement appeared to be greater than 1 mm with a load of 700 mm in group A (700 N, 2 cases), and the difference was significant between group A and group B (p < 0.05). In the sitting position, the horizontal and longitudinal displacements of the quadrilateral areas were within 0.5 mm in group A and group B, and there was no significant difference between group A and group B (p > 0.05). CONCLUSION: For complex acetabular fractures in the quadrilateral area, DAPSQ fixation may provide early sitting stability, but it is inappropriate for patients to stand too early.

Staples, tension-band plates, and percutaneous epiphysiodesis screws used for leg-length discrepancy treatment: a systematic review and proportional meta-analysis.

BACKGROUND AND PURPOSE: The primary aim of this systematic review and meta-analysis was to evaluate the success rate of 3 different epiphysiodesis techniques with implant usage for the treatment of leg-length discrepancy (LLD) in the pediatric population. The secondary aim was to address effectiveness (final LLD) and the reported complications of staples, tension-band plates (TBP), and percutaneous epiphysiodesis screws (PETS). METHODS: In this systematic review we searched MEDLINE (PubMed), Embase, Cochrane Library, Web of Science and Scopus for studies on skeletally immature patients with LLD treated with epiphysiodesis with an implant. The extracted outcome categories were effectiveness of epiphysiodesis (LLD measurements pre-/postoperatively, successful/unsuccessful) and complications that were graded on severity. RESULTS: 44 studies (2,184 patients) were included. 455 underwent epiphysiodesis with PETS, 578 patients with TBP, and 1,048 with staples. Successful epiphysiodesis was reported in 76% (95% confidence interval [CI] 61-89) with PETS (9 studies), 67% (CI 54-79) with TBP (10 studies), and 51% (CI 28-65) with Blount staples (8 studies). From pooled analysis, the severe complications rate was 7% for PETS, 17% for TBP, and 16% for Blount staples. Angular deformity was reported in 4% after PETS, 10% after TBP, and 17% after Blount staples. CONCLUSION: Our results showed that epiphysiodesis with PETS implants was the most successful technique. PETS had a higher success rate, fewer severe complications, and a lower proportion with angular deformity.

Thermographic analysis of perforations in polyurethane blocks performed with experimental conical drill bit in comparison to conventional orthopedic drill bit: a preliminary study.

OBJECTIVE: Conical orthopedic drill bits may have the potential to improve the stabilization of orthopedic screws. During perforations, heat energy is released, and elevated temperatures could be related to thermal osteonecrosis. This study was designed to evaluate the thermal behavior of an experimental conical drill bit, when compared to the conventional cylindrical drill, using polyurethane blocks perforations. RESULTS: The sample was divided into two groups, according to the method of drilling, including 25 polyurethane blocks in each: In Group 1, perforations were performed with a conventional orthopedic cylindrical drill; while in Group 2, an experimental conical drill was used. No statistically significant difference was observed in relation to the maximum temperature (MT) during the entire drilling in the groups, however the perforation time (PT) was slightly longer in Group 2. Each drill bit perforated five times and number of perforations was not correlated with a temperature increase, when evaluated universally or isolated by groups. The PT had no correlation with an increase in temperature when evaluating the perforations universally (n = 50) and in Group 1 alone; however, Group 2 showed an inversely proportional correlation for these variables, indicating that, for the conical drill bit, drillings with longer PT had lower MT.

Effect of cortical bone thickness on shear stress and force in orthodontic miniscrew-bone interface - A finite element analysis.

Miniscrews are widely used in orthodontics as an anchorage device while aligning teeth. Shear stress in the miniscrew-bone interface is an important factor when the miniscrew makes contact with the bone. The objective of this study was to analyze the shear stress and force in the screw-bone interface for varying Cortical Bone Thickness (CBT) using Finite Element Analysis (FEA). Varying CBT of 1.09 mm (1.09CBT) and 2.66 mm (2.66CBT) with miniscrews of Ø1.2 mm, 10 mm length (T1), Ø1.2 mm, 6 mm length (T2) and Ø1.6 mm, 8 mm length (T3) were analyzed. Six Finite Element (FE) models were developed with cortical, cancellous bone, miniscrews and gingiva as a prism. A deflection of 0.1 mm was applied on the neck of the miniscrews at 0°, +30° and -30° angles. The shear stress and force in the screw-bone interface were assessed. The results showed that the CBT affects the shear stress and force in the screw-bone interface region in addition to the screw dimensions and deflection angulations. T1 screw generated lesser shear stress in 1.09CBTand 2.66CBTcompared to T2 and T3 screws. Higher CBT is preferred for better primary stability in shear aspect. Clinically applied forces of 200 gms to 300 gms to an anchorage device induces shear stress in the miniscrew-bone interface region might cause stress shielding. Thus, clinicians need to consider the effect of varying CBT and the size of the miniscrews for the stability, reduced stress shielding and better anchorage during orthodontic treatment.

Computed Tomography-Based Occipital Condyle Morphometric Analysis in the Turkish Population: A Trajectory Analysis for Optimal Screw Selection.

AIM: To provide a comprehensive analysis for accurate screw size selection and insertion angle during surgical procedures. MATERIAL AND METHODS: In this retrospective study, a total of 120 patients participated, resulting in the analysis of 240 occipital condyles using coronal, sagittal, and axial planes on CT scans. Statistical evaluation was performed using the Wilcoxon rank-sum test, with p < 0.05 considered statistically significant. RESULTS: The mean sagittal length and height were measured at 17.2 ± 1.7 mm and 9.1 ± 1.5 mm, respectively. The average condyle angle, a crucial factor for screw insertion, was assessed at 38.0 ± 5.5 mm in length, 19.6 ± 2.6 mm in width, and 9.5 ± 1.0 mm in height. Condyle height in the anterior and posterior hypoglossal canals was measured at 10.8 ± 1.4 mm and 9.0 ± 1.4 mm, respectively. Screw angle and condyle width were statistically smaller in females compared to the male population. CONCLUSION: The OC is a significant anatomical structure in the craniovertebral junction, playing a crucial role in stability. The obtained morphological values are applicable to the Turkish population and offer statistically significant findings for preoperative planning involving occipital condyle screw instrumentation.

Optimizing Subtalar Arthrodesis: A Human Cadaveric Evaluation of a Novel Partially-Threaded Screw Combination in the Delta Configuration.

Background and Objectives: Despite the established role of subtalar joint arthrodesis (SJA) for treatment of subtalar osteoarthritis, achieving bone union remains challenging, with up to 46% non-union rates. Adequate compression and stable fixation are crucial for successful outcomes, with internal screw fixation being the gold standard for SJA. The delta configuration, featuring highly divergent screws, offers stability, however, it can result in hardware irritation in 20-30% of patients. Solutions to solve this complication include cannulated compression screw (CCS) countersinking or cannulated compression headless screw (CCHS) application. The aim of this biomechanical study was to investigate the stability of a delta configuration for SJA utilizing either a combination of a posterior CCHS and an anterior CCS or a standard two-CCS combination. Materials and Methods: Twelve paired human cadaveric lower legs were assigned pairwise to two groups for SJA using either two CCSs (Group 1) or one posterior CCHS and one anterior CCS (Group 2). All specimens were tested under progressively increasing cyclic loading to failure, with monitoring of the talocalcaneal movements via motion tracking. Results: Initial stiffness did not differ significantly between the groups, p = 0.949. Talocalcaneal movements in terms of varus-valgus deformation and internal-external rotation were significantly bigger in Group 1 versus Group 2, p ≤ 0.026. Number of cycles until reaching 5° varus-valgus deformation was significantly higher in Group 2 versus Group 1, p = 0.029. Conclusions: A delta-configuration SJA utilizing a posterior CCHS and an anterior CCS is biomechanically superior versus a standard configuration with two CCSs. Clinically, the use of a posterior CCHS could prevent protrusion of the hardware in the heel, while an anterior CCS could facilitate less surgical time and thus less complication rates.

Comparative effectiveness of cortical bone trajectory screws and pedicle screws in the treatment of adjacent segment degeneration after lumbar fusion surgery: a systematic review and meta-analysis.

PURPOSE: To compare the efficacy and safety of cortical bone trajectory (CBT) screw and pedicle screw (PS) internal fixation in the treatment of adjacent segment degeneration (ASD) after lumbar fusion. METHODS: This study was registered on International Prospective Register of Systematic Reviews (PROSPERO) (ID: CRD42023484937). We searched PubMed, Embase, Web of Science, Cochrane Library, China National Knowledge Infrastructure (CNKI), Wan Fang Database, and Wei Pu Database by computer to collect controlled clinical studies on the efficacy and safety of cortical bone trajectory (CBT) screw and pedicle screw (PS) internal fixation in the treatment of adjacent segment degeneration (ASD) after lumbar fusion from database establishment to November 2023. Two researchers screened the literature, extracted data and evaluated the risk of bias of the included studies, recorded the authors, and sample size, and extracted the intraoperative blood loss, operation time, Oswestry disability index (ODI), Visual analogue scale (VAS), disc height (DH), hospital length stay and complications in each study. Meta-analysis was performed using Revman 5.4 software provided by Cochrane Library. RESULTS: A total of 6 cohort studies (CS) and 1 randomized controlled study with a total of 420 patients were included in this study, including 188 patients in the CBT group and 232 patients in the PS group. The CBT group had lower intraoperative blood loss than the PS group [mean difference (MD) = -129.38, 95% CI (-177.22, -81.55), P < 0.00001] and operation time was shorter than that of the PS group [MD = -1.42, 95% CI (-2.63, -0.20), P = 0.02]. Early postoperative back and leg pain improved more significantly in the CBT group [MD = -0.77, 95% CI (-1.35, -0.19), P = 0.01; MD = -0.24, 95% CI (-0.37, -0.10), P = 0.0005]. CONCLUSION: Compared with PS, CBT for adjacent segment degeneration after lumbar fusion has the advantages of less intraoperative blood loss, shorter operation time, and less back and leg pain in the early postoperative period.

Mechanical evaluation of a threaded interference interlocking mechanism for angle-stable intramedullary nailing.

OBJECTIVE: To assess the fatigue and load-to-failure mechanical characteristics of an intramedullary nail with a threaded interference design (TID) in comparison to a commercially available veterinary angle-stable nail with a Morse taper bolt design (I-Loc) of an equivalent size. METHODS: 10 single interlocking screw/bolt constructs of TID and I-Loc implants were assembled using steel pipe segments and placed through 50,000 cycles of simulated, physiologic axial or torsional loading. Entry torque, postfatigue extraction torque, and 10th, 25,000th, and 50,000th cycle torsional toggle were assessed. Each construct was then loaded to failure in the same respective direction as fatigue testing. Four complete constructs of each design were then assessed using a synthetic bone analog with a 50-mm central defect via nondestructive torsional and axial loading followed by axial load to failure. RESULTS: All constructs were angle stable at all time points and withstood fatigue loading. Median insertional torque, extraction torque-to-insertion torque ratio, and torsional yield load were 33%, 33%, and 72.5% lower, respectively, for the TID interlocking screws. No differences in torsional peak load, torsional stiffness, axial yield load, axial stiffness, or axial peak load were identified. No differences in complete construct angle stability, torsional stiffness, axial peak load, axial stiffness, or axial yield load were identified. CLINICAL RELEVANCE: The TID had an inferior torsional yield load when compared to I-Loc implants but generated angle stability and sustained simulated physiologic fatigue loading. The TID may be a suitable mechanism for generating angle stability in interlocking nails.

Torsional stability of fixation methods in basicervical femoral neck fractures: a biomechanical study.

BACKGROUND: Basicervical femoral neck fracture is a rare proximal femur fracture with a high implant failure rate. Biomechanical comparisons between cephalomedullary nails (CMNs) and dynamic hip screws (DHSs) under torsion loading are lacking. This study compared the biomechanical performance of three fixations for basicervical femoral neck fractures under torsion load during early ambulation. METHODS: The biomechanical study models used three fixations: a DHS, a DHS with an anti-rotation screw, and a short CMN. Finite element analysis was used to simulate hip rotation with muscle forces related to leg swing applied to the femur. The equivalent von Mises stress (EQV) on fixation, fragment displacement, and strain energy density at the proximal cancellous bone were monitored for fixation stability. RESULTS: The EQV of the short CMN construct (304.63 MPa) was comparable to that of the titanium DHS construct (293.39 MPa) and greater than that of the titanium DHS with an anti-rotation screw construct (200.94 MPa). The proximal fragment displacement in the short CMN construct was approximately 0.13 mm, the greatest among the constructs. The risk of screw cutout for the lag screw in short CMNs was 3.1-5.8 times greater than that for DHSs and DHSs with anti-rotation screw constructs. CONCLUSIONS: Titanium DHS combined with an anti-rotation screw provided lower fragment displacement, stress, and strain energy density in the femoral head than the other fixations under torsion load. Basicervical femoral neck fracture treated with CMNs may increase the risk of lag screw cutout.